floppy cable of USB_serial of the ser2pl.sys

Similar Questions

• should my time capsule be connected with a cable for backups, after the initial installation?

  should my time capsule be connected with a cable for backups, after the initial installation?

  If you mean that you have to keep your Mac connected to a Time Capsule via Ethernet for future backups, then the answer is no. Time Machine and time Capsule are designed to work over wireless for your Mac would just need to be connected to the wireless network provided by the time Capsule.

• I have problems to make my battery charged, because the cable does not have a link solid with the socket of the phone.  The problem seems compatible with a lot of cables, so I think the problem is with the phone. Can it be fixed?

  I have problems to make my battery charged, because the cable does not have a link solid with the socket of the phone.  The problem seems compatible with a lot of cables, so I think the problem is with the phone. Can it be fixed?

  Probably there is debris and dust in the decision-making of the lightning.  Serve with compressed gas canned (NEVER orally).  If this doesn't help, try electronic contact cleaner has a q - Tip.  Finally, take it to Apple.

• Portege R100 video cable does not reach the replacement LCD screen

  Hi guys, I have replaced the LCD screen of my Toshiba R100, than they had in it was defective. It seemed that it was a replacement at some point however. In any case, I received my new screen, but does not reach the video cable to the top of the circuit of LCD screens. How am I meant to connect it to the screen? Is there an extension cable or what? The screen they had in there previously looked like they were welded copper wires about 8 digitizer.

  Here are 2 pictures of what I mean

  

  

  Hello

  Where did you buy this screen?
  Are you sure that it is perfectly compatible with your laptop protected R100 to 100%?

  Looks like it s not fully compatible
  However, if an extra cable is necessary you can get it from the Toshiba ASP in your country.

  In your case, I recommend you contact the guy and ask for compatible cable!

  Welcome them

• When I connect my Ipad or Iphone to my computer via a USB cable, I can open the storage folder without using a password. How can I avoid someone else do the same?

  When I connect my Ipad or Iphone to my computer via a USB cable, I can open the storage folder without using a password. How can I avoid someone else do the same?

  This storage folder are you referring? If you are referring to the film, what happens because you have accepted a trust between the iOS device and the computer. If the device has been connected to another computer, it must be unlocked and establish a relationship of trust as well. If you are referring to something different, please explain.

• Cannot boot safe mode or any mode - hangs on the mup.sys driver

  Can someone help me. I did some research on the internet and see that it is a familiar problem. I have been using a usb and someone removed without doing safely - storage key my laptop then froze and the only thing I could do was turn it off at the power button.

  Now I can't do anything - it just goes to several times on the same page saying that there was a problem to choose a way to start - I chose alone and nothing - it loads until the mup.sys driver and then just goes to the same page again. I'm out of ideas.

  Can anyone help?
  I'm trying to avoid the recovery disk that I really want to lose my job yet, but realize that might have to happen, you mind I read reports that it even still hangs when you try this option.

  Thanks Rachel

  Hello

  AFAIK the mup.sys is placed in the folder C:\Windows\System32\drivers and it s responsible for the control and the start-up of the operation of the system at the lower level (control of the printer or the graphics card, etc.).

  If your computer loads all the way up to mup.sys then your HARD drive should work. If he died it would not even charge anything at all. It would not even try to load this file.
  It is likely that this file is corrupted just.

  If you re not able to run the Win operating system and use the System Restore tool, so I put t see any other possibility to use the Toshiba Recovery CD.
  To save important files, you can remove the laptop HARD drive and connect the HARD drive to another computer via the USB interface.

• The fcpcmcia.sys file is not found on a Portege M200

  Hello

  Someone at - he never understand the problem "the file fcpcmcia.sys is not found"? I saw in another post, but suggestions does not solve it and the post has been locked while I couldn't answer.

  I have a Toshiba Portege M200, who has the same problem when I try to put in Windows XP Tablet PC edition 2005 level. I used the recovery CD to return to XP Tablet PC edition (because the previous installation was messed up) and then tried to launch the installation of Windows from a couple different XP Tablet PC 2005 CD that I got from MSDN.

  When I try to reboot when the installation program tells me to do, he runs the Windows Installer, but it quickly fails with the "the file fcpcmcia.sys is not found." She did not mention a location where the file is supposed to be. I can't get into Windows XP Tablet PC (first edition) very well and I see there are 3 files fcpcmcia.sys hard disk.

  Any ideas? I have to upgrade this Tablet PC for the 2005 edition, because some software I need to run demands it. I tried to reinstall the fcpcmcia.sys (drivers FreeCom) but that did not help.

  The CD player I use is a Targus slimline CD-ROM/DVD-ROM (PCMCIA, USB not) which is recommended by Toshiba on their Web site.

  Thank you

  Bob

  Hello

  It is difficult to say why this message.
  The problem is that you have installed the OS of the original note Toshiba recovery CD.
  On the page of the Toshiba driver I found the cardbus driver. Maybe you need this driver?

  Usually if you install the new operating system, you must install the correct drivers Toshiba in the right order. The chipset utility, cardbus, common modules driver are very important and must be installed first.

• restart the server because of the Awvusbd64.sys file

  Hello

  When I checked the minidump file to know the cause for the restart of the server, I got under info

  Probably caused by: Awvusbd64.sys (Awvusbd64 + aa47)

  Help, please

  The pilot originally, the Awvusbd64.sys, is the USB driver anywhere.

  A similar error is mentioned in the following link:

  http://forums.Digi.com/support/forum/printthread_thread, 7265_printall, Yes

  If you have a SafeNet dongle it may be a confilct.

• I want to install a HD floppy Microsoft 2002, I have the keycodes, how can I do this? Windows XP, Works Suite 2002.

  I want to install a HD floppy Microsoft 2002, I have the keycodes, how can I do this? Windows XP, Works Suite 2002.

  Hi, Edward.

  Follow the steps listed here

• I want to install a HD floppy Microsoft 2002, I have the keycodes, how can I do this?

  I want to install a HD floppy Microsoft 2002, I have the keycodes, how can I do this?

  Microsoft 2002 what?

• where I can down load the mdismpx.sys file

  When I try to register my GPS upor, it asked me to download the MDISMPX.sys file, can someone tell me where I drop can I load?

  Hello

  Welcome to the Microsoft community.

  I understand how it could be frustrating when things do not work as expected. Please, I beg you, don't worry I'll try my best to resolve the issue.

  Are you Mdismpx.sys or Rndismpx.sys?

  If you get Rndismpx.sys you can refer to this article:

  Given that the problem is related to Upor GPS recording.  I suggest you to contact the support of the Callaway Upro for better assistance.

  http://www.callawayuxplore.com/support

  Please follow all the steps and if the problem persists, return back and we will be happy to help you.

• My floppy drive is not reading the disks. Device Manager does not detect any problems, I uninstalled and reinstalled the drivers. Now what?

  Floppy drive read only not the disks.

  Hello Fishface1977,

  Thank you for your message.  If nothing has changed on your system, recently, to include hardware, software or updates?  Also, have you installed the drivers that came on the CD with your system or you download/install the drivers the most recent of the website of the manufacturer of your computer?  It is recommended that you download/install the drivers provided by your computer manufacturer's website.  Please let us know so that we can better help you get this issue resolved.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.

• Windows XP, the power option button is gray and does not work. The hiberfil.sys file occupies all the available space.

  I can't install the updates, especially antiviruse updates and everything is slow because the hiberfil.sys file is huge.  I can't Devil Hibernate because the power button is gray-no matter how or where I'm trying to open it.  Also at the same time, the sound disappeared and the sound card displays a yellow button.  Difficult to use the computer and dangerous online.   Help!
  Eve

  Hi EveMontgomery,
   
  You can disable hibernation by running the hotfix given below article tool to solve this problem:
  How to disable and re-enable hibernation on a computer that is running Windows
   
  To solve the sound problem, follow the three steps solution given in the link below and see if this helps you.

  No sound in Windows

• How can I make sure my internet cable works even if the icon is not displayed by the clock

  I see the wireless connection icon, but I used to see one for the wired connection also. So where is it?

  How can I make sure my internet cable works even if the icon is not displayed by the clock?

  Click Start > Control Panel > network and Internet > network connections.

  Click with the right button on your Local network, and select Properties. In the window properties of LAN make you that these boxes are checked.

  [] Display the icon in the Notification area when connected

  [] Notify me when this connection is limited or no connectivity.

  Click [OK] and get out of here!

  Right-click on start and select Properties. On the taskbar and Start Menu click the taskbar tab, and then click the Customize in front of the Hide icon button inactive and it make sure that the option 'always show' for the local network is selected.

  HTH,

  NASS - http://www.nasstec.co.uk

• My floppy drive is not reading the disks. Device Manager does not detect any problems, I uninstalled and reinstalled the drivers. What should I do now?

  My floppy drive is not reading the disks. Device Manager does not detect any problems, I uninstalled and reinstalled the drivers.
  Convenience store said to click on properties Insert the diskette and
  Double click on open, but when I do that it stop computer
  and opens the recovery and ask for a correct diskette,

  Hello Tallm,

  Thank you for your message.  Did you get your floppy drivers of your installation diskettes?  If so, go to the website of the manufacturer of your computer and download/install the latest drivers.  Please let us know if this or help to solve your problem.
  See you soon

  Engineer Jason Microsoft Support answers visit our Microsoft answers feedback Forum and let us know what you think.