Good IP address of my router extreme need.

Similar Questions

• How can I find screen confiquration router I need to enter a mac address for Xavier

  Xbox is having a problem contecting to the router by telling me to enter a mac address on-screen router confiquration... where is it?

  Hello

  I suggest you follow the link below and check if this can help:

  http://support.Xbox.com/en-us/pages/Xbox-360/troubleshoot/KB/error-cant-obtain-IP-address-router-modem.aspx?kbid=978976

  You can also post your query on Xbox discussion forum:

  http://forums.Xbox.com/

• Registry files have been deleted via a Norton 360 3.0 registry clean up - can't get an ip address from the router

  I'm running Vista Ultimate, -connection (Ethernet) with Verizon FIOS I ran a Norton registry clean and foolishly trust what he says to remove.

  At first, all of my USB cards have been screwed up (noted in the Device Manager with exclamation next to each one points)
  I did a system restore and that corrects this problem, but now I'm having a problem with my network card.
  , All diagnostic tests, etc. show that the material is very good. My router is also fine the problem is that windows can't get an IP address from the router and then assigns his own
  (a # 169 instead of a # 192)
  In the network connection properties, it says that the device is functioning correctly, and the driver is up-to-date.
  'Connection speed' tab: a window of diagnosstics is: I ran testto test adapters connect to connect to the network.
  Results: connection Test
  Test details:

  I have "this card is configured to obtain an IP address automatically. No DHCP server is present on the network. Windows selected an IP address by using the alternative private IP addressing. »

  X "Ping 0.0.0.0 Gateway: failure.
  !  "No DNS server is available for this connection.
  ! "No WINS server is available for this computer.
  X "Ping 0.0.0.0 network: failure.
  ------------------- -------------------------------------------------------------------------------------------------------------
  In this same window of diagnostics under the "LinksTab".
  Link current test status: (what is determine the current connection speed of the adapter and link partner)
  Results:
  ! The adapter is configured to negotiate the speed with the link partner, but 1000 Mbps was chosen as one of the possible speeds.

  The best link options-results of the speed test:
  ! Could not detect way reliable speed and duplex settings. Possible speed/duplex settings are 100 Mbps Full Duplex and Half Duplex 100.
  (Note that these link tests are online and I can't online)

  Also in the Diagnostics window-under the 'Cable' link cable - past-polarity is normal.
  Depending on the tab is the Hardware tab
  Hardware diagnostics check for I/O conflicts...
  Results: all the tests:
  EEPROM test
  FIFO test
  Test register
  Interruption of the tests
  Loopback test

  I also went in the prompt type in IPCONFIG... c which shows:
  Ethernet connection to the Local network card:
  ConnectionSpecific DNS suffix: (it's completely empty here)
  Link-local IPv6 address: fe80::bda9:951 d: 619f:a0dc 9%
  Autoconfiguration IPv4 address: 169.254.160.220
  Subnet mask: 255.255.0.0
  Default Gateway: 0.0.0.0

  I also have a sort of ping command here-cant remember the command, but the results were in the CBS... I didn't know how to reach. He however escape from something on the registry files.

  I went throughD-Link Tech router (router) support is good, Fios Tech support everything set up right, - Norton support(Norton denies that the files were not to be touched-although their report shows these registry files were deleted)-Dell Tech support because my warranty missed 3 weeks ago - although I still have the "your Tech Support team until 2013 - which is valid only if you have a hardware warranty-made no sense sold me the car without. the engine - directed the FTC to bring a complaint about it - after I get this fixed number.

  I hope someone can help... by the way I get perfectly in line with my laptop - I know this isn't my router. I'm sure it's due to some registry files being moved-(j'ai eu deles de messages d'erreur indiquant que les fichiers de Registre ont été endommagées ou manquantes) what do I do now? No system restore to restore this part of the register - I also installed the drivers from the dell drivers and Utilities disc - but maybe I've done that correctly? I put the disc - extract files-(he says they have been unpacked) was a new step for me to do after that? Help, please!
  Thank you!

  Hello
   
  We recommend that you install the router (see its manual) and the pilot of NIC once more and check the difference. In the first post, you mentioned that you decompressed or extracted files. Once the files are extracted, you will be asked to install the driver. However if you do not receive any prompts for the driver, then you will need to locate the destination folder where the files are checked to find the configuration file.
  
  Open the destination folder where the files are extracted and run the Setup file to complete the installation.
   
  To download and install the latest network card driver, visit the site Web of the manufacturer of the device or system.
   
  For more information on downloading and installing the drivers, visit this link:
  http://Windows.Microsoft.com/en-us/Windows-Vista/the-hunt-for-drivers-how-to-find-Windows-Vista-drivers-for-all-your-hardware
   
  I hope this helps.
  Kind regards
  Syed
  Answers from Microsoft supports the engineer.

• How to block a MAC address on my router?

  I need to know to block a MAC address on my router

  You must open 192.168.1.1 in a browser (such as Internet Explorer) [usually the user name and password are admin]. Then go to security settings (depending on the manufacturer, the user interface varies) where block you a particular MAC address, or allow only a specific MAC address (options vary for the manufacturer).

  If any additional support is required, you can contact the support of manufacturer of router for assistance.

• Printer HP B209a does not get the IP address of my router

  Computer is a HP G71 running under Windows 7 64-bit

  Router is a NETGEAR's WNR3500L with the latest firmware and a unique SSID

  Using the latest version of the software install HP B209a

  Towards the end of the installation for the wireless feature, the installation stops and tells me that my PC is on a network other than my printer.  All wireless devices connected to my router have 10.0.0 # IP addresses.  Through many installs the printers IP address is constantly as 192.168.0.109.  The summary on the printer wireless shows my unique routers SSID but when I open my router software and devices attached, the printer is not listed.  My router is attached to a simple DSL modem with no wireless features.  I tried the following hotfixes recommended in these forums.

  1. Connect the printer to the router through WPS with push button.  Connection is returned as a success, but identified printer router SSID as grabbled alphanumeric characters and not an IP address.  Router does not show the printer in the devices.  During the printing installation software PC and printer fail to communicate when the USB cable is connected.
  2. Connect the printer to the router through WPS with PIN.  Connection is returned as a success, but all the information in the router has been changed and all other wireless devices disconnected.  Connection to the router has shown the SSID THAT became grabbled of alphanumeric characters and the security key was changed.  No wireless device was attached to the router, but the wired connections remain intact.  Fixed key SSID and security.  All other wireless devices back in place, printer does not have.
  3. Ping network devices.  Ping 10.0.0.1 to 7 came back as successful.  192.168.1.109 ping failed.
  4. IP address of the printer has entered into a browser address bar.  Returns a Google search page, but not for access to the network printer.  Address of more than one entry address bar and couldn't connect to 10.0.0.1 (router) and 192.168.0.1 (DSL modem)
  5. Unplug the DSL modem router.  All wireless devices to connect to the router but do not have access to the internet.  During the installation of the printer software, when you are prompted to connect the USB to the PC, printer and PC fail to communicate.
  6. Turned off the Windows Firewall, both public and private without success
  7. Used the Hp network diagnostic utility and it does not can find printer.

  I have installed and uninstalled the software several times.  The printer has always identified my identifier SSID is correct and the network key.  But during the finalization of installation I get the message and cannot connect PC printer because they are on different networks.  I have no idea where the printer receives the IP address.  It should be an address from the router, but it is not.  IP address of the modem DSL IS in the format # 192.168.0, but given that the modem is the base model with the wireless or network capabilities, the printer cannot logically connect to it.  I tried to unplug the router and the printer several times without success.  The possibility of changing the IP of the printer through the browser is not possible for the reasons given in 4.  What are the other options to change the IP address of the printer?  If I can assign an address # 10.0.0, I think it will solve my problems.

  Is your DSL modem is a modem/router combo (most are)?  If so, it probably has a structure of 192.168.0.X and is probably a wired router (only).

  This DSL modem/router is attached to the WAN, or one of the LAN ports on the back of the Netgear?  Try to move to the other type of port, and then restart both routers.

  On the front of the printer, click the settings 'Restore defaults' and wireless the wireless radio.

  Finally, the Netgear settings, here are some tips:

  1 make sure that DHCP is active, the SSID is not hidden and that MAC filtering is not enabled.

  2. ensure that the 802.11 g mode (as well as other modes is very well).

  3. use WPA or WPA encryption, not WEP (it is not secure and may cause connection problems)

  4 change the channel of the Netgear to 11 (Yes, I know it makes no sense, but it works).

• How to access server dns on a photosmart 7510 address to set the address of my router?

  My father has just got a photosmart 7510.  I have a trendnet wireless router, which has a few computers connected wirelessly.  To get these to connect, I had to modify the IPv4 settings to set the default gateway and dns server addresses main address of my router. On the printer, I can find where to enter the default gateway, but NOT the primary dns server.  Printing of network configuration settings shows the dns backend as 0.0.0.0, as is the case, the router gave the printer MAC address, but they cannot talk to each other on IP and of setting up the PC on the network, I know that it won't work correctly together w/that.

  Where in the printer configuration menus this value is located so I can put it?

  Oh, OK.  We should perhaps solve the problem of connection to the router, get the printer connected to it with a DHCP address, then go to the printer web page and tweak it.

  -Reboot the router by removing the power momentarily.

  -Change the channel to 11 router and make sure that you use WPA or WPA2

  -On the printer to go wireless > restore network keybord.

  -In the same network menu, run the Wireless Setup Wizard.

  The printer must be connected to the router, then you should be able to access it via its IP address.

• IP ADDRESS OF THE ROUTER WRT320N

  I recently bought the WRT320N router.  Set up was easy, I have 2
  computers (1 wired and 1 wireless). I have a wired
  printer. Recently, my son, home from College and he was able
  access my network of wirleess without any security problem.  The simple link
  Counsel has not indicated his computer while he was on the network (it
  lists the mentioned previously 2 computers and printers).  I tried
  to access the routers Set up basic web. I checked my computer and the
  The IP address is 192.168.1.1.  However, when I try to get on the web through the
  (http://192.168.1.1), I get "Internet Explorer can not display the.
  Web page.  Why is this happening? Why does my network seem to not course?

  Open a command window and type in ipconfig.  Verify that the default gateway to verify the IP address of your router is 192.168.1.1.  If this isn't the case connect you to this address and see if you can get to the admin pages.

  If it is still impossible to connect hard reset the router by pressing the reset for 30 seconds button and hold then release.  Wait 30 seconds and cycle power to the router.  Do not attempt to connect with the username password empty admin.  Reconfigure your router to your setting, then check your secruity.

• When you set the IP address of the router, WRT160N Inaccessible

  Hello

  I bought a WRT160N router yesterday and eagerly tried to connect my laptop to the internet (ADSL) modem using this router. As my ADSL modem is a router DHCP too, and I want to keep it like that, I have it plugged in ethernet cable form one of my ADSL modem/router, LAN ports in one of the LAN ports on the modem, Linksys have the Linksys operating as a bridge. However when I tried to specify an address of router static IP (192.168.1.254) in the basic parameters of configuration Linksys Panel, disabled the DHCP setting and saved, I could not connect to the router more using this new IP address - my browser tells me that the Web page doesn't seem to exist, but it cannot establish a connection with her. Then I have to reset the router in order to access configuration panels using the default address 192.168.1.1. Is there a reason why I cannot access the control panels of the router with the new IP address of the router that I've specified?

  Thanks for any help,

  Hello

  the problem is resolved, be it in a different way. I tried your trick to wait 30 seconds after the registration and the recycling of the modem, but this had no effect. What helped does not change the settings for address IP Routerl and the setting from the DHCP server on the router for the disabled at the same time. If I only changed the setting to the IP address of the router and recorded, the modem has been reset automatically and starts with the new correct router address. After that I changed the setting of DHCP server to the WRTN160 to off and then I was able to get the router working, like I wanted.

  I assume that when you connect the router to a computer reset (after taking out the IP address of the computer) with DHCP from the active router, the router assigns an IP address to the computer that somehow interferes with the local IP address parameter, if you define that at the same time.

  In any case, all work now, and I have excellent signal everywhere in the House. I guess that congratulations go to me :-) but still thanks to eliminate one possible cause of the problem

  Kind regards

  Gerard

• Bind the MAC to the static IP address with WRT54GL router

  Hello

  We use the WRT54GL Wireless router to connect 4 pc to internet. One of these pc requires a static IP address, because the router can do only reliable port-forwarding for IP static (I would ssh it and use it as a web server). I was told that this router has this ability, but for the life of me I can't find.

  Could someone tell me how to proceed? I am running the latest firmware (v4.30.11).

  Thanks in advance for your reply,

  Michiel

  DD - WRT is fairly stable and well maintained. There are a lot of people using it and you get excellent support, if you don't mind not very technical responses to opportunities. Generally, the flashing of the firmware does not support the warranty. But that wouldn't be a problem if you have had a bad flash. And even for a bad flash you often have options to recover the router.

  For the static IP address on the computer, change the settings of network to the ethernet interface. I do not know Gentoo you should have administration GUI for this somewhere.

  You can use the following values:

  IP (as mentioned earlier) for instance 192.168.1.10
  subnet mask 255.255.255.0
  address of the gateway 192.168.1.1
  192.168.1.1 DNS server

  As long as the static IP addresses do not conflict with the DHCP server address pool create there will be problems running some static IP computers in the same local network with DHCP clients.

• find the ip address for actiontec router

  How to get the IP for windows vista

  Hello

  Follow these steps to find the IP address of the router:

  a. click on the "Start" button in the Windows taskbar. Right click on 'network '. Click 'properties '. The Network and Sharing Center will be open.
  b. click on the "View state" button to the right of the wireless network connection.
  c. click on "Details". The IP address of the router will appear next to the IPv4 IP address.

  Kind regards
  Afzal Taher
  Microsoft technical support engineer

• The IP address specified by Microsoft is different from the IP address of my router

  I received an email from Microsoft about unusual activity in my account. I changed my password twice since then. The email indicates a different IP address than that of the mi router. I also checked the recent activity and it shows an estimated position which is not close to me, but it's in the same district. It does not show firefox and ie browsers used, which is fine because I tried them both. Is it possible to display 2 IP addresses? I worry because I also received a message from yahoo indicating a 'sign in warned. I also changed my yahoo just in case. I am quite illiterate on technical issues so simplicity will appreciate in any recommendation. Thank you, AG

  I received an email from Microsoft about unusual activity in my account.

  -> Which account are you thinking of? Your Windows logon account? An e-mail account?

  The email indicates a different IP address than that of the mi router.

  -> This is an email that you have received (and not sent)? It show what address? How did you determine the IP address of your router?

  I also checked the recent activity

  -> How did you do that?

  I am quite illiterate on technical issues so simplicity will appreciate in any recommendation.

  ->, I suspect that you have received a fraudulent e-mail that has been generated by a person who is trying to get you to give them access to your PC. You should not do in any circumstance.

• How to find the IP address of the router from my computer in Windows 7?

  What is the best way to find the IP address of the router from my computer in Windows 7? I know not how to make using the start > cmd > ipconfig, but is there a way to do it with just the mouse?

  Right click on the WiFi icon or-> LAN in the system tray click on open network and sharing Center-> click on "Wireless network connection"--> details click-> see item highlighted on the screenshot:

  

• My printer Photosmart D100a wireless continues to change the IP address when the router reboots.

  My printer Photosmart D100a wireless continues to change the IP address when the router reboots.

  Another idea is to unnstall HP software (using its uninstall program), then restart your PC.  Finally, download the latest version of the software for your printer from the "Support & drivers" link at the top of this page.

  Meanwhile, keep your antivirus operational.  The installer configure it for you during the installation of the printer.

• I want to use my email to yahoo in form.would pls contact address, you explain what I need to do step by step? TNX

  I want to use my email to yahoo in form.would pls contact address, you explain what I need to do step by step? TNX

  Please check junk / e-mail notification file. Also, the server should support PHP mail.

  https://forums.Adobe.com/docs/doc-3581

  Thank you

  Sanjit

• Retrieve the external IP address of the router from a paralytic

  Hello

  I'm working on a workflow, that the provisions, a complete paralytic, I have nearly all that work, the only issue I am running into is not able to shoot/get the external IP address of the router once that vApp is put into service. Does anyone know which API can I gives the floor to get that information? I have attached a screenshot of the NAT tab in the firewall of vApp to give more details on the specific element, I'm trying to recover. Any help would be greatly appreciated.

  Thank you

  J

  Here's an excerpt from one of my workflows in test I use to inspect a vApp on vCloud Director with vCO 5.5 5.5:

  System.log("=== Network Configurations ===");
  var networkConfigurations = vApp.getVappNetworkConfigurations();
  for each (cfg in networkConfigurations){
      System.log("href: "+cfg.href);
      System.log("Description: "+cfg.description);
      System.log("isDeployed: "+cfg.isDeployed);
      var netConfig = cfg.configuration;
      System.log("ipScope: "+netConfig.ipScope);
      var routerInfo = netConfig.routerInfo;
      if (routerInfo != null){
          System.log("External IP: "+routerInfo.externalIp);
      }
  }
  

  I would like to know if this is useful, I just double it checked by running against one of my vApps has a similar configuration (NAT and Port Forwarding) and it displays the correct external IP address for me.

  [2014-02-18 11:41:33.514] [I] === Network Configurations ===
  [2014-02-18 11:41:33.515] [I] href: null
  [2014-02-18 11:41:33.515] [I] Description: This is a special place-holder used for disconnected network interfaces.
  [2014-02-18 11:41:33.515] [I] isDeployed: false
  [2014-02-18 11:41:33.515] [I] ipScope: null
  [2014-02-18 11:41:33.516] [I] href: null
  [2014-02-18 11:41:33.516] [I] Description:
  [2014-02-18 11:41:33.516] [I] isDeployed: true
  [2014-02-18 11:41:33.516] [I] ipScope: null
  [2014-02-18 11:41:33.516] [I] External IP: 192.168.1.61