Grid Console and Console Configuration change?

Similar Questions

• Backup and managing configurations on ONS 15454 devices

  We have a lot of ONS 15454 and CiscoWorks LMS 4 apparently does not support these devices (I can't pick the cards ML1000 configurations or configs of chassis).

  Can I save the configurations of the STC cards/chassis using the CTC? I see a backup option of database under maintenance contract, but I'm not entirely of this make. Basically, I want to assure you that if one of these devices suffers a hardware failure, I have backups of the way in which the circuits are provided.

  Is there a better tool to use?

  Any advice would be great

  For nodes to backup through the CTC, the Cisco ONS 15454 procedure Guides describe the steps to be taken to save the nodes (section below the latest version is:)

  Cisco Transport Manager is a management system of item available for the largest optical networks and has features to back up the databases of several nodes.

  =========

  NTP-A108 back up the database

  Goal	This procedure saves a backup version of the TCC2/TCC2P (software) database on the workstation running Cisco transport (CTC) controller or a network server.
  Tools/equipment	None
  Pre-trial proceedings	None
  Required / have required	Mandatory. Cisco recommends to perform a backup of database at intervals of about a week and before and after configuration changes.
  Onsite / remote	On-site or remotely
  Security level	Maintenance or higher

  

  Note You need to back up and restore the database for each node on a path of the circuit in order to maintain a complete circuit.

  

  Note The following settings are not backed up and restored: node name and Internet Inter - ORB Protocol (IIOP) port. If you change the name of the node and restore a backup of a database with a different node name, the circuits map to the new node name. Cisco recommends keeping a record of the old and new node names.

  Step 1 Complete the "DLP-A60 Log into CTC" task at the node that you want to back up. If you are already connected, go to step 2.

  Step 2 Click it maintenance > Database tabs.

  Step 3 Click on backup.

  Step 4 Save the database on the hard drive of the workstation or network storage. Use a file name with the extension of .db file. for example, database.db.

  Step 5 Click Save.

  Step 6 Click OK in the confirmation dialog box.

  Stop. You have completed this procedure.

• How to: display "last configuration change.

  How can I get my routers to display:

  "The last configuration change" and

  "configuration change since...". »

  and if possible I can trap on these?

  1720 = 12.2 IOS

  Thank you in advance,

  Bart

  To get these displays the router must make sure what date and time is. The best way to do this is to run NTP and learn the time from an NTP server. An alternative is to use the clock control to set time.

  When the router has a time that authoritative display you want is automatic.

• 6 ESXi, nVidia GRID, vCSA and problems of Console mouse

  All,

  I'm running into a problem with the mouse on my VDI machines control deployed with GRID NVidia GPU in k-1.

  The machines I deployed with the GPU K1 can no longer be controlled by using the console.  Either thick client or web client.  The servers that are running on the same host are fine, but anything with map GRID on it, fails to display the mouse in Console.

  Rotates through the documents best practices for GRID map and all parameters seem to be good.   Also tried to re - install (uninstall, reinstall) VMtools.

  Any help is appreciated.

  Thank you!

  You will lose the console if you use vGPU or vDGA on a virtual machine.

  I suggest to use another way to on these remote administration, Remote Desktop for example.

  Linjo

• Not able to get the 192.168.1.1 console configuration in Bridge Mode only

  Hello

  I use the Linksys WAG200G wireless modem and connection mode is ' Bridge Mode Only ', in this mode I do not get the console configuration 192.168.1.1 and Wifi set-up. Please help me to solve these problems. Appreciate your help. Thank you.

  1. you set a static IP address, for example 192.168.1.2 mask 255.255.255.0 on the computer and he wire the WAG to get access.

  2. do not allow the wireless and basically anything else on the WAG during a bridge mode. In bridge mode, it works like a standard modem and all you can change is the modem related settings.

• All my configuration page and fonts have changed suddenly, how to restore the previous settings. THX

  All my configuration page and fonts have changed suddenly, how to restore the previous settings. THX

  Hi André Haub,

  Follow the steps in this document to perform a system restore. This process restores your system to a previous point files.

• "Windows updates were not be properly configured and restoration of changes." The computer freeze

  I have a laptop Dell inspiron 1501 with windows vista on it.

  I don't have the disc of windows Vista DVD you are referring to, I have never recived a Dell I bought the computer on the internet with vista already installed.

  My problem is that, with respect to the windows updates, I get a message saying "Windows have been developed to date not be properly configured and restoration of changes". I have 51 updates pending, 47 of these updates is equivalent to 170 MB.

  As a result of these updates, I think it's the cause of my freezing computer once I have connected and I have to restart only having do not 2 - 3 times.

  When the computer "freezes" the cursor does not move throughout the scene, none of the keys works, including Manager tasks etc., the only thing that works is to turn the computer off. Sometimes, there is a beep, beep once the computer crashes.

  Over 95% the updates I have try have 'no '.

  I'm lost as how to how to repair?

  All good suggestions welcome to solve this problem, the simpler the better... I don't want to have to buy a new computer... If I won't Dell... and I'll have to get the windows disc... most solutions here seem to require it...

  Hi AL0001,

  Run the chkdsk command to check that there are no problems with your hard drive. To run the disk check, follow these steps:

  1. Restart your computer and immediately press the F8 key until you reach the menu Advanced Boot Options.
  2. Select Mode safe mode with command prompt.
  3. At the command prompt, type chkdsk/r (there is a space between the k and /)

  Meanwhile, check the Dell website to see how you can get a recovery disk in case you need to recover Windows.

• Very new to photoshop, I try to make changes to a photo and set up as a dynamic object, but after the selection of dynamic object, the grid appears and my photo dissppears

  Very new to photoshop, I try to make changes to a photo and set up as a dynamic object, but after the selection of dynamic object, the grid appears and my photo dissppears

  Well, something's wrong with Photoshop. Try to close Photoshop, and then press Command + Option + shift as you restart Photoshop. You will be asked to clear the Photoshop preferences. ATTENTION: you will lose all current preferences.

• Domain name for the IP and EBS r12 changed the configuration

  Dear all
  
  
  I have oracle ebs r12 installed on the development server on 64-bit linux OEL, I changed my domain name and IP address of this server. Please help me how to change this configuration to the instance of the EBS. When I run adstrtal.sh apps/apps his mistake to see the
  
  opmn id = hostname.domain.com:6200
  No matched process or applications.
  
  domain name shown above is old it is changed. name of domain and IP is changed no host name.
  
  Please advice how to retrieve.
  
  Abdelouahed

  Did you complete the steps described in these documents?

  Note: 338003.1 - how to change the host name or port of the database layer using automatic configuration
  Note: 341322.1 - how to change the hostname of a stream of Applications using automatic configuration

  Additionally, make sure that you clean the FND_NODES table according to the (how clean non-existent nodes or addresses IP of FND_NODES [260887.1 ID]).

  Thank you
  Hussein

• Syslog. Include the address IP of VTY in each message (the configuration changes)

  Hello guys,.

  I discovered that Huawei has a syslog messages different format when it comes to saving the configuration changes in external syslog, however if in Cisco you use a universal login for many users, it is impossible to know what connected IP address who commands...

  I know, a solution would be to allow all users to use its own login, however, I wanted to know is possible for a Cisco router associate the vty from the payer 'connected command' and include this information in Syslog.

  Here is the example for Huawei:

  %%10SHELL/5/cmd (l): - DevIP = 10.219.3.2 - 2 - task: vt0 ip:10.200.7.138 user: * command: display buffer

  Cisco has kind of understands the final message where says what was the IP address of the VTY, however, this IP address is not present in each message syslog like Huawei.

  68954: 168799: sep 22 14:29:21.839: % PARSER-5-CFGLOG_LOGGEDCMD: user: XXXXX connected command: no connection host 10.200.100.10 transport udp port 515

  68952: 168796: 14:18:25.341 Sep 22: % PARSER-5-CFGLOG_LOGGEDCMD: user: XXXXX connected command: exit

  68953: 168797: sep 22 14:18:26.053: % SYS-5-CONFIG_I: configured from console by XXXXX on vty5 (10.200.7.138)

  Is it possible to do something similar in Cisco

  If you Splunk or another business journal reports server you can correlate these events by building a transaction whenever you see a % SYS-5-CONFIG_I event. I have support for this in my application of networks Cisco for Splunk: https://apps.splunk.com/app/1352/ & https://apps.splunk.com/app/1467/

  Take a look and see what you think.

• I have 3 domains. A field is a constant date mm/dd/yy. The second field is a digital number (1-120) and can be changed. The third field calculates two fields 1 and 2 in the summation and shown in mm/dd/yy. How do I calculate that in the script?

  How do I calculate that in the script? I have 3 domains. A field is a constant date mm/dd/yy. The second field is a digital number (1-120) and can be changed. The third field calculates two fields 1 and 2 in the summation and shown in mm/dd/yy.

  You searched for ' add days?

  You must write a custom for this JavaScript calculation because you cannot add a number any date. Also the date strings are not just a number, even if we can convert a given date in a number for that date that represents the time form a date date (Epoch). Witn this value, we can achieve them all kinds of date calculations and collect a little information about the date. JavaScirpt uses midnight on January 1, 1970 UTC for starting point or the date of the time. Its value is zero, and every millisecond increases the value of 1. When a date string is converted to the date object JavaScirpt we have access to many properties of the date and can use several methods to extract information or adjust the date object.

  Field 1 is in the format "Date" with a format of "mm/dd/yy".

  Field 2 is in «Number» format with 0 decimal.

  Zone 3 is in the format 'None '. The custom calculation script applies to the formatting.

  The custom for JavaScript calculation area 3:

  var cField1 = this.getField("Field_1").valueAsString;

  var cField2 = this.getField("Field_2").valueAsString;

  Event.Value = "";

  If (cField1! = "" & cField2!) = "") {}

  Console.println (cField1 + "" + cField2);

  calculate that if we as no null data;

  var cDateFormat = "mm/dd/yy";

  convert start date date object.

  Kai var = util.scand (cDateFormat, cField1);

  get the date of the month;

  David var = oDate.getDate ();

  Add field 2 number of days;

  David = Number (nDate) + Number (cField2);

  of being updated for the new date.

  oDate.setDate (nDate);

  Set the field to update formatting;

  Event.Value = util.printd (cDateFormat, letter);

  } / / end of data not null;

• I noticed from lately, when I change my settings on the 2 online games, I play, I can disconnect turn it back on and notice the changes eventually reversed to where it was before.

  original title: Vista settings will not save. Why?

  I have a problem. When you use this computer (and this computer has Windows Vista), I noticed from lately, when I change my settings on the 2 online games, I play, I can disconnect turn it back on and notice the changes eventually reversed to where it was before.

  It's getting boring because it is not happened in the past and when I noticed it happened for the 2nd game after seeing this constantly on my 1st game, it came to me that it is not the games that does this: it is the computer itself.

  What should I do so that the computer can actually record setting changes I made?

  Hey, Andrew,.

  Most likely a configuration of settings on your computer file is damaged. You can take a look at this article that Blizzard has published:

  http://us.battle.NET/support/en/article/fixing-corruption-and-damage-in-your-game-files

  You can also ask your question on the forums of World of Warcraft:

  http://us.battle.NET/wow/en/Forum/1011701/

• The ACE can be configured for recording the syslog server configuration changes?

  Hello

  On all our routers, switches and firewalls, we have configured syslog so we get headlines when configuration changes occur.

  Is it possible on the ACE too?

  Kind regards

  Sebastian

  Hi Sebastian,.

  Yes it is possible but depends on the upong the logging level, you have defined. So record trap 5 should be able to get configuration changes or command execution logs.

  November 1, 2013 11:20:33: ACE-5-111008%: "admin" user running the command "logging buffered 6'.

  November 1, 2013 11:20:48: ACE-5-111008%: "admin" user running the command "no book testlog.

  So, you should see these newspapers of level 5 on syslog if siphon 5 logging is configured.

  Let me know if you have any questions.

  Kind regards

  Kanwal

• by default become wallpaper and do not change...

  Hi you

  I installed window 8 I want to change my wallpaper, but it became by default and do not change.... Please help me...

  Hi Brian,.

  Thanks for posting your query on the Microsoft Community.

  Thank you for details on the issue and we will help solve you this problem.

  Make sure that your graphics driver is updated. I suggest you try the methods and check them off below if it helps:

  Method 1:

  1. Right-click on your desktop and click on Personalize.
  2. Click on the desktop background.
  3. Select a wallpaper or choose one of the themes.

  If the problem persists then follow the method below.

  Method 2: To activate the setting wallpaper the Office of the Local Group Policy Editor.

  1. On the screen, press the Windows key + R.
  2. Type gpedit.msc and click on OK.
  3. Under User Configuration , click Administrative Templates.
  4. Double-click Office.
  5. Yet once, double click on desktop.
  6. Double-click desktop wallpaper
  7. Change the setting on " Enabled".
  8. Click apply and Ok.

  Try the procedure described in the following Microsoft Help article and check if that helps.

  http://Windows.Microsoft.com/en-us/Windows-8/personalize-PC-Tutorial

  Hope this information is useful. Let us know if you need more help, we will be happy to help you.

  Thank you.

• Installation of updates Windows comes to approximately 96% complete, then said: "failed to update Windows, restore configuration changes.

  I just bought an Acer Aspire 5600U all-in-one computer. When attempting to install Windows updates, sometimes about 96% complete, then said: "failed to update Windows, restore configuration changes. How to solve this problem?

  Original title: Windows updates

  Hello

  Please, try to reset components Windows Update as mentioned here and see if this helps:
  http://www.kapilarya.com/fix-error-80070570-Windows-Update-encountered-an-unknown-error-some-updates-were-not-installed
  Hope this helps, good luck :)