Hide parts of the follow-up process of the workspace

Similar Questions

• Read only access (to hide part of the config)

  Is there a way to allow read-only access to only part of the config.  I have clients that require read-only access, but I don't want the portions to the config.

  For any help or suggestion would be greatly appreciated.  Thank you

  If they have a connection to enable level, they will be able to see the entire configuration (absence of passwords encrypted assuming you are using the service encryption password).

  You can make more granular connections and prevent customers from, say, the ability to run arbitrary commands such as "show run". For example you could setup a given user to be alllowed to run 'show interface status' etc. NX - OS has this ability almost "cooked in the oven-in." IOS systems, to a little more work.

  Here's a guide to how to do if you use GANYMEDE for AAA:

  https://supportforums.Cisco.com/docs/doc-15765

  If you use local authentication, you can do similar things, using cli views or levels of privilege:

  http://www.Cisco.com/en/us/docs/iOS/12_2t/12_2t13/feature/guide/ftprienh.html

  http://www.Cisco.com/en/us/docs/iOS/12_3t/12_3t7/feature/guide/gtclivws.html

  http://www.NetworkWorld.com/community/node/57553

  I hope this helps.

• Virtual keyboard hides part of the change to the field

  Hello

  I have a labelfield, field change and a button that are centered aligned vertically. The three fields, I added in a Verticalfield Manager which is then added to a horizontal region Manager. And finally the HFM is added to an another value for money. Now in the 9800 device or curve 9380, I noticed that when I touch the edit field, virtual keyboard is coming. And he hides the field partially change.

  I want to move things to the top when the virtual keyboard appeared. How can I do. My code is here:

         HorizontalFieldManager hfm = new HorizontalFieldManager();
          VerticalFieldManager vfmComponent = new VerticalFieldManager(USE_ALL_WIDTH);
          vfmComponent.add(lfServerUrl);
          vfmComponent.add(mEfURL);
          vfmComponent.add(mBtnSave);
          hfm.add(vfmComponent);
          int topEmptySpace = (Display.getHeight() - (Bitmap.getBitmapResource(mStrTopBar).getHeight() + hfm.getPreferredHeight() + 25)) / 2;
          hfm.setMargin(topEmptySpace, 0, 0, 0);
          VerticalFieldManager vfmMain = new VerticalFieldManager(VERTICAL_SCROLL| NO_HORIZONTAL_SCROLL );
          vfmMain.add(hfm);
          add(vfmMain);
  

  Help, please.

  When you start to need as many managers to get the look you want, then you know that you should really create your own Manager.

  These two should help you to do:

  http://supportforums.BlackBerry.com/T5/Java-development/how-to-extend-Manager/Ta-p/446749

  http://supportforums.BlackBerry.com/T5/Java-development/create-a-custom-layout-manager-for-a-screen/...

  For example, I hacked together a "centeringManager" and the screen, which should do what you want.  But please use this as a reference sample, understand what he does and maybe even improve it.

  In production code, I would really remove the centeredManager and centering Manager across all fields and place them, but then you must code a manager which includes margins, which would confuse the point of this example - as a basic implementation of a Manager.

  Hope it's what you want.

  public final class CenteringScreen extends MainScreen {
  
      /**
       * verticallyCenteringManager takes one Field and positions it
       * centered in the space it has.
       */
      VerticalFieldManager centeringManager = new VerticalFieldManager() {
          protected void sublayout(int maxWidth, int maxHeight) {
              if ( this.getFieldCount() > 1 ) {
                  throw new RuntimeException("Expecting only one Field or Manager to be added");
              }
              if ( this.getFieldCount() == 1 ) {
                  Field f = this.getField(0);
                  layoutChild(f, maxWidth, maxHeight);
                  int requiredTopMargin = (maxHeight - f.getHeight())/2;
                  int requiredLeftMargin = (maxWidth - f.getWidth())/2;
                  setPositionChild(f, requiredLeftMargin, requiredTopMargin);
                  setExtent(maxWidth, maxHeight);
              } else {
                  setExtent(0, 0);
              }
          }
      };
  
      /**
       * Fields added to centeredManager will be displayed 'centered' vertically
       * regardless of orientation of screen and presence or absence
       * of virtual keyboard
       */
      VerticalFieldManager centeredManager = new VerticalFieldManager(VerticalFieldManager.VERTICAL_SCROLL | VerticalFieldManager.VERTICAL_SCROLLBAR);
  
      // Sample Fields to be added
      ButtonField sampleButton = new ButtonField("Button", ButtonField.FIELD_HCENTER);
      LabelField sampleLabel = new LabelField("Label", LabelField.FIELD_HCENTER);
      BasicEditField sampleBef = new BasicEditField("Text", "", 255, BasicEditField.FIELD_HCENTER);
  
      public CenteringScreen() {        
  
          super(Manager.NO_VERTICAL_SCROLL); // very important
          // The NO_VERTICAL_SCROLL means that the only Manager added to this Screen - centeringManager -
          // will be given as its maxHeight, the available screen height, regardless of
          // orientation or whether there is a virtual keyboard displayed
  
          // add Fields to centeredManager
          centeredManager.add(sampleButton);
          centeredManager.add(sampleLabel);
          centeredManager.add(sampleBef);
          centeringManager.add(centeredManager);
          this.add(centeringManager);
  
      }
  
  }
  

• Tool/Navigator panels hide part of the picture that I'm working on.

  How can I prevent the image I am trying to be obscured by the panels of the tool and Navigator when I select them on the develop Module?

  Press the space bar, which activates the hand tool, and then drag the image as needed.

  Or press Tab to hide the panels, press Tab again to make them reappear.

  You can also right-click on the little arrows on the sides and choose the manual option - in this way that they will not go out when you hover over them.

• PrE11: Active project box hides part of the monitor preview

  When you select the Adjust button or applied effects the displayed menus convienently slide the control screen to the left.  When you select the active button of the project and the menu unfolds this mask partially the control screen.  It may be more or less depending on the adjustable size of the active project menu.  The control screen don't move the road as with menus setting or applied effects.

  Can monitor preview somehow moved or taken to go?  Can the box of active project be transferred?

  Windows 7 64 bit

  Pre 11 64 bit

  16 GB of ram

  monitor 17 ''

  Thank you.

  Bill

  whsprague wrote:

  Can monitor preview somehow moved or taken to go?  Can the box of active project be transferred?

  No and no. The mobile components from earlier versions (accessible via the window > display host headers) is spent in v11.

  You can refine the drop by positioning the cursor on the right and slippery edge show only three columns.

  Note, however, that the usual behavior of the assets of the project drop-down is turning off when you click outside of it. He is only staying on screen because you chose to pin there.

  

  See you soon,.
  --
  Neale
  Insanity is hereditary, get you your children

• Dedicated is part of the Instance server process or not?

  Hi friends,

  I am new to Oracle database. I read book celebrates 'Expert Oracle Database Architecture' by Thomas kyte. Page n ° 62, he stated that "this dedicated server process is not (by definition) part of the instance."

  But in the [email protected] documentation to almost most of the places, they have mentioned this dedicated server is part of an instance. Interestingly, Tom Kyte has co-written book. I got confused because the dedicated server process would also PGA, so he will be part of the memory, so it should be part of the instance. Then Tom Kyte said to this dedicated particular process and why? It must be said that with any reason? What is it?

  I also asked my coach. But I don't have a satisfactory answer.

  Thank you.

  67bf3bdd-9577-45A7-a776-f8e8d3c9c0d3 wrote:

  Hi friends,

  I am new to Oracle database. I read book celebrates 'Expert Oracle Database Architecture' by Thomas kyte. Page n ° 62, he stated that "this dedicated server process is not (by definition) part of the instance."

  But in the documentations of [email protected] almost most of the places, they have mentioned that this dedicated server is part of an instance. Interestingly, Tom Kyte has co-written book. I got confused because the dedicated server process would also PGA, so he will be part of the memory, so it should be part of the instance. Then Tom Kyte said to this dedicated particular process and why? It must be said that with any reason? What is c?

  I also asked my coach. But I don't have a satisfactory answer.

  Thank you.

  Can cite you an instance- specific documentation indicating that dedicated server is part of the Forum?  Your embedded link is a "mailto" link, not a url to a document.

  I can provide specific links indicating otherwise.

  If I start to the Online Documentation of the database to Oracle 11 g Release 2 (11.2) I'm on the portal for all documents in database 11.2.

  From there, do a search for "dedicated server" and the results of this research to Oracle Database Search Results: dedicated server

  The first returned result is the definition in the Glossary

  The definition States:

  dedicated server

  A configuration database in which a Server process handles requests for a single client process.

  If I followed the link incorporated for the "server process", I get the definition of a "process server" to the Glossary

  Note that this definition is for the "process server", not just dedicated server.  It is said

  process server

  An Oracle process that communicates with a client process and the Oracle database to meet the demands of the user. The server processes are associated with an instance of database, but are not part of the instance.

  (underlining)

• Firefox address field hide the last part of the address when loading.

  Firefox to hide the last part of the address entered when they were loaded.

  
  

• iTunes update errors with the following message appears: there is a problem with this Windows Installer package. A program run as part of the set up did not complete as expected.

  iTunes error update

  I am trying to install an update to iTunes on my laptop and find the folowing part-way through the installation error:

  "There is a problem with this Windows Installer package. A program run as part of the set up did not complete as expected. Contact your provider to support personal or package. »

  I got iTunes for 3-4 years now and have always been able to install updates successfully, so don't not sure what is the problem.

  I tried msconfig and changed the boot process, so it includes all of the non-Windows elements, as suggested on the Microsoft Web site, but that has not worked.

  Can anyone help?

  Thank you

  The instructions were to contact the vendor of the package. This isn't iTunes, Microsoft.

  Ask the question in the Apple Forums:
  https://discussions.Apple.com/index.jspa

• Part of the 'geography name referring to program' of the upgrade process?

  Hi all

  We were upgraded to R12.1.3 and currently in the first iteration.

  When you query the former transaction window workbench Transaction we get,"'the system cannot determine the geographic information for this place and cannot be derived from a tax jurisdiction. Contact your system administrator"error.

  I ran the "geography name program referencing" after getting this error. and that the error has been resolved.

  Advice kindly, 'name geography program SEO ', is it process a part of the upgrade or manually run the program.

  Thank you

  AtulR

  Please see:

  Workbench transaction error: the system cannot determine the geographic information for this place and cannot be derived from a tax jurisdiction (Doc ID 438718.1)

  Form transaction error: interviewing or creating a movement triggers the error: the system cannot determine the geographic information for this place and cannot be derived from a tax jurisdiction. Please contact your system administrator. (Doc ID 1350601.1)

  Problem of referencing name geography: Map_status for a location_id is 'E' in the table HZ_GEO_NAME_REFERENCE_LOG (Doc ID 1368312.1)

  Thank you

  Hussein

• How to dynamically change the last part of the url inside the body HTML in e-mail send to Apex process

  Hello

  I need to change the last part of the URL sent by post in the apex dynamically. I have a requirement that a person can register itself with a new user name and other details. When the user clicks on the button register after you have entered all the required values in the page all values will be inserted into the user_details_repository table in the database. At the same time an email with a url link is sent to the user admin for the assertion. When the admin user, click on the link it is redirected to a page where all the details submitted by this particular user is displayed. The admin user can confirm or reject the new user registration. If the admin user says, all the data repository of this particular user table will be inserted in a main table named user_details and data will be deleted from the repository table. Yet once if the admin user rejects, all the data repository of this particular user table will be deleted.

  For this, I have created two pages for this and all of the features mentioned above works correctly except change the link url each time a letter is sent to the admin user when a new user register itself. To send email, I created send e-mail process. I need to change the last word/part of URLs within html body according to the username provided by the new user.

  for example, the url to another user will be like this:

  http://localhost: 8080/apex/f? p = 103:9:3849261906471:NO:USERNAME:Namrata

  http://localhost: 8080/apex/f? p = 103:9:3849261906471:NO:USERNAME:Madhura

  Help, please.

  If there is another way to achieve the same thing please answer.

  Thank you

  Nilesh

  Hi Nilesh,

  You can use a Page element as a substitution variable in the body of the HTML message.

  for example, blah blah blah & P123_MY_PAGE_ITEM. blah blah blah

  The syntax is an ampersand in front of the name of page element and a point after the name.

  brgds,

  Peter

• Hide or crop part of the background image

  I am currently studying in master suite CS4. In InDesign, my background image is bigger than my canvas size (more bleeding). How to hide or reframe the portions of the image that go outside of the canvas size? I know it must be simple, but I'm just not see it.

  Do you mean bigger than the page? Or pasteboard? If this is the page, just use the black arrow to move one edge of the worms inside the frame. The content will still be there, but the part of it will be hidden. If it is larger than the editing table that I don't know, because I assume that you will not see the handles. Harvest before placing them?

• Wizard BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  This has two questions:

  1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.

  2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.

  3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.

  Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.

  The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.

  Then there is the BootCamp partition on the HARD drive partition #2.

  Is there a way to get what I need?

  That is what has been described in this notice of two canoes?

  Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3

  n-on-a-3-TB-fusion-drive http://twocanoes.com/Winclone/support/installing-Windows-on-a-Boot-Camp-partitio

  Thank you.

  After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.

  Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.

  A. take backup

  1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.

  B. fuse out of the merger in two physical disks drive: SSD + HDD

  1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)

  Cs diskutil list

  2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive.  Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.

  I hit this issue too.  To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:

  Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)

  and repeat for disk1/dev/disk1 which is the HARD drive in my case).

  This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.

  2 create independent partitions (non-fusionend) for the installation of OSX.

  Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".

  3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".

  C. install on the HARD disk as drive didier autonomous not fusion.

  1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.

  D. use BootCamp Yosemite f5 to install windows.

  1. launch Yosemite bootcamp.

  2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software.  Do not click on the last box to install or remove windows pie creating real bootcamp partition again.

  3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.

  4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use.  Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model).  Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.

  -From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.

  -Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.

  -Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.

  5. open Boot Camp Assistant again and only select the third option, install Windows 7.

  It will show you the screen to select what installation disk, select HARD drive.

  Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.

  For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.

  Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio

  6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.

  7. once the installation is complete, check that windows is functioning correctly.

  E. Si you want to upgrade to windows 10 Windows 7.

  1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page.  Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE.  Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.

  2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.

  F. reinstall OSX El Capitan

  Once your target windows system (if windows 7, windows 8 or windows 10) works very well.  You can continue to create again your Fusion drive and reinstall OSX El Capitan.

  1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.

  6 type the 'diskutil list' command to list all disks and partitions.

  The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.

  The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.

  G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc

  1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.

  Cs diskutil list

  6. in the terminal, type commands to delete logical drives from basic storage.  Note: All data will be destroyed in the logical drive.

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 121,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS GB SSD 121.0 disk0s2

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Apple_HFS 1.7 Untitled TB disk1s2

  3: disk1s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 503.0 GB disk1s4

  5: Apple_HFS 801,4 Untitled GB disk1s5

  8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.

  diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5

  Note: Mark the group id of logical volume shown in the results.

  In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.

  So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2

  9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.

  diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%

  10 command "diskutil cs type list" to check the resulting fusion drive created.

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E

  =========================================================

  Name: LVG

  Status: online

  Dimensions: 1815635525632 B (1.8 to)

  Free space: 90112 B (90.1 KB)

  |

  +-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 120988852224 B (121.0 GB)

  |

  +-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E

  |   ----------------------------------------------------

  |   Index: 1

  |   Disc: disk1s2

  |   Status: online

  |   Dimensions: 1694646673408 B (1.7 to)

  |

  +--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10

  ---------------------------------------------------

  Disc: disk2

  Status: online

  Size (Total): 1809780178944 B (1.8 to)

  Reversible: no

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  LVG Type: Fusion, sparse

  11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.

  12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.

  13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.

  14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.

  15. yet once please take personal responsibility on damage if you follow the instructions in this article.

• What are the official names of the parts of the window of Windows 7?

  I searched the official help files, but they don't show a picture of Notepad and talk of the title bar and the bar of menu etc.  I suppose it's useful for * Notepad * and many other applications that not much has changed...

  But I want to know the details of the new Windows 7 Windows Explorer window...

  You know, the "Aero" window  These things you have official names?

  Is it still the bar when he has no title of title (only the keys of control: reduce, enlarge, close)?

  What is the official label for the next bar?  "Navigation/Search Bar?  "Go-go Bar"?

  And the following?  "Command bar"?  "Standard toolbar?

  I was going to create an image, but I found one in the Windows Help file (I saw only Notepad example you mentioned first, but discovered an example of folder too).  Here's how to get there:

  1 - Press Windows-F1 to open Windows Help & Support.
  2 - Click on "learn the basics of Windows.
  3. under the heading programs, files and folders, click work with files and folders
  4 - scroll down (about halfway) under the heading understanding the parts of a window, where you will see the example image.
  The menu bar and the status bar are available, but disabled by default, so they are not included in the description.
  Also, not described is the title bar (although still there and visible on the technical level, the themes Aero comes hide text).  The command menu that normally indicates a program's icon is there too, just invisible (click in the upper left corner to see the menu).

• Martin Rosse - circulate returned comments on all or part of the reviewers.

  On behalf of Martin Rosse.

  Question: I don't see the possibility more to circulate back to all or part of the reviewers comments (by adding their email addresses in a separate step when setting up e-mail review). Is - it is no longer possible?

  Answer: I apologize because I could not understand the question. You want to add multiple recipients through tracker once you distribute the PDF document.

  Required information.

  Please provide the step by step procedure that you used to use Acrobat 9. If possible, join the snapshot, so I can understand and answer you.

  What are the options I really don't think that we stopped one of them in Acrobat X (in the Distribution of the PDF).

  Concerning

  SaVe

  

  Okey. So, if I'm not mistaken, allows you to get this option by clicking address book (step 3 of 4) option in the window to distribute the form. Acrobat 9 and 10, you can get later:

  (1) come to the window where you enter the email addresses by following the process of normal distribution.

  (2) click on 'To' button. It's right next to the text box where you enter the email addresses.

  (3) once you click on 'To' contacts will open and show you the option 'CC '.

  Is that what you're looking for? In case it is something different, please open this link and let me know at what stage you get that option and I'll tell you where exactly he is available in format Acrobat 9 / X. If this is the case.

  http://http://Acrobat.timhuff.NET/?p=10

  ~SaVe

• Is shuttle - possible to print values in the second part of the shuttle

  Shuttle took 2. parts. Is it possible to also load values iin database part of the shuttle at the beginning? For example the user sees in the first part of the books of the shuttle of database he loves, and in the second part of the shuttle books that he dislikes database. It could pass the books from one to the other part of the shuttle. Is this possible?

  Hello

  I set up a page the demo of the functionality you need: [http://htmldb.oracle.com/pls/otn/f?p=22619:4]

  This is based on the following tables:

  EMP
  EMPNO pk
  ENAME

  BOOKS
  BOOK_ID pk
  BOOK_NAME

  EMP_BOOKS
  EMP_BOOK_ID pk
  EMPNO fk
  FK BOOK_ID
  DATE_OUT

  What I did is:

  1 created a Select list with Submit called P4_EMPNO to allow you to choose an employee. The SQL code for this is:

  SELECT ENAME d, EMPNO r FROM EMP
  ORDER BY 1
  

  I have disabled the use of null values or extra.

  2 created a calculation before header which is subordinated to the P4_EMPNO = NULL, makes:

  SELECT EMPNO
  FROM EMP
  WHERE ENAME = (SELECT MIN(ENAME) FROM EMP)
  

  This just ensures that P4_EMPNO has a selected value when the page is loaded for the first time.

  3 created a shuttle component called P4_BOOKS that has a SQL query to:

  SELECT BOOK_NAME d, BOOK_ID r
  FROM BOOKS
  

  Note that I list all THE books here

  4 created a PL/SQL process that runs without condition "on the load - before the heading" with the following code:

  DECLARE
   vBOOKS VARCHAR2(100);
   vSEP VARCHAR2(1);
  BEGIN
   vBOOKS := '';
   FOR C IN (SELECT BOOK_ID FROM EMP_BOOKS WHERE EMPNO = :P4_EMPNO)
   LOOP
    vBOOKS := vBOOKS || vSEP || C.BOOK_ID;
    vSEP := ':';
   END LOOP;
   :P4_BOOKS := vBOOKS;
  END;
  

  This creates a string delimited by colon BOOK_ID values already selected for the current user and sets this string P4_BOOKS. The BOOK_IDs in this string, then say the features of the shuttle to move the items in the list on the right - then, all that is left in the list on the left is not selected for the user (so is your NOT IN)

  5. I have a button on the page called P4_SUBMIT_BUTTON that submits the page and redirects to page 4

  6 - Finally, I have a PL/SQL process that runs on submit, triggered by the submit button and has the following code:

  BEGIN
   DELETE FROM EMP_BOOKS
   WHERE EMPNO = :P4_EMPNO
   AND ':' || :P4_BOOKS || ':' NOT LIKE '%:' || BOOK_ID || ':%';
  
   INSERT INTO EMP_BOOKS (EMPNO, BOOK_ID, DATE_OUT)
   SELECT :P4_EMPNO, BOOK_ID, SYSDATE
   FROM BOOKS
   WHERE ':' || :P4_BOOKS || ':' LIKE '%:' || BOOK_ID || ':%'
   AND BOOK_ID NOT IN (SELECT BOOK_ID FROM EMP_BOOKS WHERE EMPNO = :P4_EMPNO);
  
  END;
  

  It removes the books of the EMP_BOOKS table for the employee, where they have been deselected (that is to say, inserted in the list on the left). It inserts then the books in the EMP_BOOKS table for the employee where the books appear in the right list BUT not included in the table EMP_BOOKS.

  And that's all!

  Andy