Similar Questions

• How to access point password value

  I created two points where the element type is password.

  Name of the element is P1_PASS1 and P1_PASS2I

  In the PL/SQL code, I can't access the values ITEM P1_PASS1 and P1_PASS2

  I tried to debug too, but there is no value printed in the debug log.

  Actually, I want to call to a PL/SQL procedure where I need to pass the value as a variable. How to access values of these elements of password? I use 5 APEX

  Start

  wwv_flow. Debug ('test123');

  wwv_flow. Debug ('pass' |) V ('P1_PASS1'));

  p_testproc (V ('P1_PASS1'),: P1_RETVAL);

  end;

  If your problem is fixed?

• How does a wireless access Point?

  Hi all

  I've been Googling, but mostly they talk about how install Access point, but did not mention on how it actually works internally.

  T1) I just don't see AP as 'L2 wireless switch' which also fill the radio signal to the cable network network

  Q2) can AP work as long as independent if I want just a wireless connectivity in devices on it, without an uplink to any router.

  Kind regards
  Noob

  You will usually have many thinking just like a switch of layer 2 that happens to have a RF transceiver instead the banks of the port.  There is a little smarter, because it must consider for encryption and transfer of active sessions when the user moves from WAP to WAP, that sort of thing.

  Types a lot, if not all, have an 'ad hoc' (instead of 'infrastructure' mode) mode to pair pair without broader connectivity.  Never used it myself, end customers, I have worked with absolutely want the uplink router - if they are away from e-mail more than 47.2 seconds, they get tensed.

• How to access the CLI Mode in cisco sf 302 - 08 p 8-port 10/100 Managed switch

  Hello

  Can someone help me on how to access the CLI mode in cisco sf 302 - 08 p 8-port 10/100 Managed switch. I treid the each method they mentioned in the administration guide. I am not able to enter the command debug mode and comand menu after resetting the default password. Once connected, sound directly to guide me to switch main menu.

  Hello FAL, Mark,.

  Thank you for your participation in the community of support to small businesses. My name is Nico Muselle of Cisco Sofia HWC.

  To access the CLI, you must make sure that the version of the firmware on your switch is at least 1.1.0.73 or preferably higher. Then activate telnet or ssh on the switch and opening of these sessions or a console session you will see that you are in CLI mode. You can return to the console to function menu using the menucommand.

  I hope that answers your questions!

  Best regards

  Best regards

  Nico glacier

  Senior Network Engineer - CCNA - CCNA security

• How to access method Interface Client of App Mod from an another App Mod?

  Hello
  
  I have an application with a model project. It contains a module of application (say 'SharedAppMod') kept at the level of the session. There a few objects in view.
  A customer util Interface method is added to this SharedAppMod that is filtering for the object of said view with the said values and returns the result set. Structure is presented below.
  
  By SharedAppModImpl,
  
  lines filterUsingSecondaryRowSet (card) {} public
  Rowset resultRowSet = null;
  String [] attrNames = (String []) map.get('zoom') ("AttributeNames");
  Object [] attrValues = (Object []) map.get('zoom') ("AttributeValues");
  String viewObjectName = (String) map.get('zoom') ("ViewObjectName");
  ......
  ......
  }
  
  This project has been set in the jar to lib adf file to rest projects available in the rest of the applications. In so doing, given that this method of client interface is exposed under the control of data across applications, we are able to add an entry of the method described in our def file and run it to bean managed by discover the operation binding.
  
  But when you want to access the same method of AppModImpl or viewObjImpl from the rest of the applications, we do not know how to access.
  
  Can ppl give you an idea on how this can be done?
  
  Thanks in advance.
  
  Kind regards
  Julien V

  You can add the other module of the (shared) application to your application root module (main). Double-click the application root module and select the tab "DataModel" develop research of node n 'ApplicationModuleInstances' of the other module of application on the left side of the random. Select it and it shuffle to the right. This makes it accessible from the application module root (e.g. findApplicationModule or by the method that is created by the frame).

  Timo

• RV180W add the access point with itinerant support

  I have a client with a RV180w the latest firmware running.  We currently use the router as a router and provide wireless access.  We want to add a wireless coverage and I'm interested in our options.  We have a network unifying ethernet that we could use to give the new connectivity LAN AP.  Can buy us another RV180W and use it in AP mode and roaming wireless connectivity.  The customer wants a guest and business WLAN so we'll use the VLAN of the router.  How we set up the new AP?  Should we use WDS?   If we use WDS, can we still use WPA2?  Thank you for your help.

  Hello, Mr. Carl,.

  Yes is possible to use WDS and WPA2 at the same time.

  The master of accreditation will be setup as a RADIUS server to authenticate the other access points, while clients use the WPA2-PSK, which occupies the same on each access point.

  Let me share with you the information found on WDS and the configuration of basic, found on the guide me section.

  WDS configuration:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=ea8660ccb0cf4ae99cebfafd4303cdc1_WDS_Configuration_on_RV180W.XML&PID=4&FCID=&fpid=&slnid=13

  RV180W configuration:

  http://sbkb.Cisco.com/CiscoSB/UKP.aspx?VW=1&docid=dd5990ef4ad947ae89da5c3e0b8bd985_Wireless_Configuration_on_RV180W.XML&PID=4&FCID=&fpid=&slnid=4

  If this answer is satisfactory to you, please mark it as response.

  Diego Rodriguez

  Cisco network engineer

  Thank you

• How to access my voicemail from another phone?

  My Iphone is stuck in reboot mode (the logo remains on the screen) and when I connected to itunes and tried the update, I got error message 4013, saying that it cannot be updated and I need to restore. Is there another way to fix it without having to restore and lose all my data?

  You have asked two different questions here. If you receive an error 4013, then take a look at this document of support for the troubleshooting steps.  If you see the 9-4005, 4013, 4014 error when you restore your device iOS - Apple Support

  With regard to access to your voicemail from another phone, you must talk to your cellular operator and know how to access voicemail from another phone. They control the voice mail and would be able to explain their procedures, if you don't find anything on their website. It usually requires that call you your phone number, then press a series of buttons to enter your password to enter the voicemail server.

• HP Jet 8 5801 how to access the webcam

  I just bought HP 8 5801 stream, product number K5L4OUA. The card that I printed shows it has a front and a rear facing camera, but I can't find how to access the rear side.  The camera screen does not show how.

  Also, how can I return the default tablet.

  Hello mlmarsh2,

  To access the front camera, will be the camera is on and showing the live mode view, wide upward from the bottom and you will see a taskbar with the option 'change Camera.

  I see another post, that you have created that you had difficulty with some applications uninstall.

  To restore Windows to factory, off the shelf.

  Hold down the power button and the Volume button simultaneously for a few seconds.

  A screen lights up showing some options.

  Choose F11 for the system recovery option and follow the prompts.

  Hope that helps.

  PS: If this is the first time you used a Tablet, you may prefer the traditional workstations such as Windows 7 has. You can install Classic Shell Setup on the tablet of flows for the old office and it will work as well as it does on a tower or laptop.

• Empty the screen how to access the start menu

  There is no start menu in windows vista, after I improved my avast & restarted

  Hello

  See if that helps you.

  Do a Safe Mode system restore to before the problem started.

  http://bertk.MVPs.org/html/restoresysv.html

  How to access Safe Mode

  http://www.bleepingcomputer.com/tutorials/how-to-start-Windows-in-safe-mode/#Vista

  See you soon.

• E4200 Lan LAN connection - how to access the router

  Just bought the E4200 (for a home network) and have implemented as a Lan - Lan connection success. My Siemens Spreadstream DSL modem 6520 provided by Bell Aliant (is a wireless router / and is used as DHCP).  On the E4200 as per instruction changed the IP of E4200 address to 192.168.1.2, turned off the DHCP and NAT set to disabled. The E4200 is linked directly from the SpeedStream ethernet port to ports numbered on E4200 (not the internet port). The SpreedStream also feeds a Linksys switch with 16 ports (SD216).  When I connect a laptop through the new E4200 wirelesss network, I am able to see the rest of my network fine.

  When I connect a PC with the CISCO software installed to one of the ports E4200 software cannot access router of the E4200. I type 198.168.1.2 as a web address, but cannot connect. My question is, after all, the background information is... How can I access my new router E4200 to make changes with my lan - lan configuration. I want to be able to add an external drive USD to USB port of the E4200 years set up the account of wireless of comments.

  Kind regards

  Kevin Reid

  Charlottetown,

  Prince Edward Island

  Canada

  Change the address LAN IP of the E4200 to 192.168.2.2. Except, however, if 192.168.2.2 is part of the Siemens server DHCP address pool. Check which addresses IP Siemens allows to assign by using DHCP. The E4200 address must not be included.

  If you have the latest firmware installed your E4200 takes the bridge mode. In bridge mode, you can use the E4200 as access point connecting with the internet port for your Siemens. This way you can also use network comments and other features that will not or do not fully work with the configuration that you have right now...

• WAP54G Access Point using wireless mode, but not worked. :(

  I bought today WAP54G.
  My son and I have PC but we distance between our room each other and
  wireless signal is not strong enough sometimes.
  My son has wired Internet w / WRT54GS router and I have wireless
  USB G adapter to my room.
  Cat w / Linksys rep, the other day and he recommended buying WAP54G and I could leave this AP @ salon and do not need to have the connection cable.

  Anyway, I don't know how to install this customer service, called today
  and she told me that I need to install the CD in my computer. But there is no
  connection by cable or router and I cannot install CD in my computer.
  So, I installed the CD in the PC of my son who has wired Internet and
  router. The installation has been completed.
  After the installation, turn off AP and move on to the living room.
  Then, there is no "link" light on. Lamp only Power and act on.

  Tried chat w / online but offline and it is really difficult to chat w /.
  them.

  Please let me know:
  1. can I use this without wired access point?
  I would like to implement the AP @ living room (between my son and my room)
  2. which PC do I need to install CD? But once again, my PC have no cable
  connection and cannot install the CD.

  I am very beginner wireless and PC so please tell me step by step.
  I read manual and I used the installation CD Wizard but still do not work.

  Please someone help me.

  I think that you must configure your AP as Repeater wireless... Follow the link here , make sure that when you set your Access Point to the "Wireless Repeater" mode, this device will communicate only with a different Access Point Linksys (WAP54G) and wireless G of Linksys (WRT54G) router...

• RV180W - multiple wireless access points

  Hey there, looking for some advice.

  I currently have 2 two devices Cisco RV180W and I'm looking to expand my saturation wireless in my house and you're looking for the best way. a bit of back story... I originally had a signal (1) RV180W and it was in my basement (essentially a pop room configuration) and on the top floor of my house, the signal was very week. I found a text of presentation mentioned due to the chipset RV180W best wireless Extender/Expander was actually another RV180W and just used in an access point mode. So now I have two of these devices whats their best way to put in place? I saw two different implementations in this scenario and im not sure which is best.

  1. install a WDS network. Add each as authorized access points.

  2. installation each with the same SSID but together on different channels.

  What is the best configuration for the best saturation wireless within the House thus maintain the client when hoping between AP connections? also looking for easy management.

  Hello

  I would say your best bet here would be option 2, with a wired connection between them.

  WDS can be useful, but it has a few drawbacks.  For each hop that you take your speed will get divided by two, since each station can send or receive at the same time, not both.  With a wired connection eliminate you this additional relay between a router and the other on the air and can get better wireless performance.

  One thing I should mention, is that neither the installation program will result in customers maintaining connections perfectly while hopping between APs.  This would require something called seamless roaming, which is only available on the business access points where there is a controller wireless LAN involved.

  However, most of the time when hop customers between two networks it will be very fast and they will lose only briefly about connections. The decision on the time of the actual customer belongs, so that all devices will act in the same way.

  So in short, the same SSID on different channels is your best bet, ideally the channels 1, 6 or 11 If you do not overlap.

  In regard to the ease of management, they will be essentially two independent devices, each managed separately.  But once you set up the access point RV180 it will not be too many reasons to change the configuration, except maybe to change the wireless password.

  Thanks for choosing Cisco,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• How to access my password forget password in windows 7

  How to access my computer after windows 7password forgeting

  There are a lot of options built into Windows to help you out of this situation:
  • Restart the computer with your Windows repair CD, then use system restore to set Windows in a few days (only works if you have recently changed the password).
  • Log on to your account admin to spare, and then reset the password for your existing account (works only if you set up an alternative admin account).
  • Log in as administrator mode without failure, then reset the password for your existing account (the password is usually empty).
  • Insert your flash drive USB with the password key file (only works if you have taken the time to create such a key file).
  • Use the password indicator (works only if you have created a hint and if it's good enough to allow you to guess the password)
  • Check your paper files (works only if you threw down the password somewhere)

• Converted from Photo of Dollar - subscribed; How to access Adobe Stock?

  Last week, accepted the offer of conversion before the closure of the Club Photo Dollar.

  When I login now, does not show that I have access to Adobe Stock.

  Q is how to access the reserve of 100 + transferred image of the Photo Club of Dollar?

  And how get the images plus two others, that I pay for in the new subscription.

  Thanks for your help.

  Please send reply to me: (deleted by mod..)

  And unfortunately, no quick and easy way to talk to someone and get this problem is resolved.

  Thank you!

  Hello

  Please see the links below for more information:

  Common questions, Adobe Stock

  How to use Adobe Stock with CC libraries | Tutorials Adobe Creative Cloud

  Dollar Dollar Photo Club Photo Club - photo galleries free high quality royalty and vectors.

  If you still need assistance, please contact adobe support.

  Contact the customer service

• How to access the filters Gallery tab filter on Photoshop CC?  It is gray and unavailable on my screen.

  How to access the filters Gallery tab filter on Photoshop CC?  It is gray and unavailable on my screen.

  Hi Nikon_Guy,

  Could you please let me know the format of the file open in Photoshop?

  Also, what is the mode of the file?

  What version of Photoshop is installed on your computer?

  The operating system you are working on Windows or MAC?

  Kind regards

  Tanuj