How to connect my potentiometer (3 connections: wine, Vout & amp; common) to USB-6008

Similar Questions

• How to connect an lvdt and cell to usb 6008

  Please help me iam do not know how to choose a daq card. looking for a lost lt but iam.

  I want to measure the force and displacement at the same time a bench test of suspension and I wanted to use or usb6008 because of my budget for the project.

  can I use this daq card to measure these parameters?

  answer please... Thanks in advance.

  Hi Sylvia,.

  To be able to determine or not with a box NI USB-6008 would be appropriate for your application, it would be useful to get a little more information on measures you can take. If possible you would be able to provide the range of voltage, you intend to measure with your instruments and sampling rate, you need?

  I also noticed in the subject line you use an LVDT, will you also production for this tension with the 6008 or this will be done separately?

  To give you some setting in context, the NI USB-6008 case does not really simultaneous readings at every moment, but will be replacing rapdily between channels, to give effectively simultaneous samples. As this unit has a sampling rate of 10 kech. / s, and you use 2 channels, the sampling rate effective for each entry would be 5 kech. / s.

• Connect a BNC connector to a USB-6008 isometric Force sensor

  I have a force isometric sensor with a BNC socket: http://www.radnoti.com/products/force_transducers

  I want to connect to the USB-6008, but I have no experience of EA. I found on a similar forum that I can cut and strip Cable BNC and connect the positive wire to the AI0 (AI0 +) and the AI4 (AI0)-.

  http://forums.NI.com/T5/LabVIEW/how-connect-NI-USB-6008-to-BNC-out-on-transonic-T110-w-t-ground/TD-p...

  This would apply to my device?

  Thank you!

  It should work.

  Lynn

• How to connect 12 '' MacBook (2015) to a 24 "or 27" Apple Cinema Display AND fresh!

  I made this post on my site here: https://underground.net/how-to-connect-an-apple-display-to-a-usb-c-macbook/ (which I will update regularly)

  This installation took me a LONG time to understand, but it works very well, no wake mode 'sleep', etc.

  To connect the new MacBook to a 24″ Cinema Display or Apple 27″ LED Display Monitor (who both have a record which is the same as the Thunderbolt connector, but are not actually screens Thunderbolt) you can opt for a really cheap option, as the following point 3.1 AllSmartLife USB Type C adapter Mini DisplayPort Amazon for $ 20 :

  

  That works very well, but you cannot load your computer when you are connected to the screen, nor can you plug something else on your computer as an external hard drive, etc.

  To be able to recharge your computer AND connect to the screen AND connect other devices to your MacBook, you need the following configuration, and it works great, btw.

  1 first download this USB-C for USB multi-port, Belinda® USB-C for 3 ports USB 3.0 , which is about $ 36 on Amazon.

  

  2 then, you need an expensive element, StarTech.com USB 3.0 to DisplayPort 2560 x 1600 video card Multi monitor external adapter (USB32DPPRO), which is around $74 on Amazon:

  

  3 Finally you need a cheap item, the Cable questions DisplayPort / Mini DisplayPort male to female adapter at $ 9 on Amazon:

  

  Plug all the in such things and he ends up you look pretty clean where it connects to the computer, as you can see below and you can plug in the USB port of the screen on the hub and use the speakers on the screen, AND you still an available for a hard drive, external USB 3.0 port.

  

  It will cost you around $119! Wow, that's a LOT, but it works. Or you can go cheap and just get the first card for $20 but charge your MacBook by disconnecting from time to time to plug in the charger. What a PAIN in the * Apple.

  The new MacBooks coming will be equipped with a combined USB/Thunderbolt-c plug that should * hope * connect a screen and charge at the same time cheaper, but who knows?

  If you want me to your post something, I can put it on the MacBook 2015 using forum boards.

• How can I improve the rate of acquisition with daqmx and usb-6008?

  Hello

  I am trying to acquire data of analog voltage with a USB-6008. I'm under Labview 8.5 student on an HP laptop with a 1.33 Ghz cpu and 736MB RAM, apparently. I tried using the Daq assistant and the low-level Daqmx functions. My best results come with a task set in MAX for my analog input, and using the function 'Daqmx read' the 'unique double 1 d sample' value in a while loop. I insert the values returned in a table which built in the while loop, and then when I'm done, I check the number of samples in the table. In the test VI attached, I also use the time to Get before and after all loop. The best sampling rate I made using this method, is around 40samples/second. I have attached a VI below that illustrates this concept. In my actual application, the data acquisition code runs at a time while loop with 1ms, parallel to other code that controls the device I'm collecting data of. The sampling rate is roughly the same for my test below VI and my application program.

  The 6008 datasheet gives the sampling frequency maximum 10 kHz. I'd be happy with 2 to 2.5 kHz, or as soon as possible; I'm sure that I can achieve a little more than 40 Hz. My first idea was tied to the hardware, but the 6008 cannot make acquisitions NI hardware.

  My question is: How can I implement a faster sampling of analog voltages to a USB-6008 in LAbview? If I can't do it, is there another way I can taste the data more quickly?

  Thank you

  -SK-

  

  To the best of my knowledge, the USB-6008 can do timed equipment acquisition. Don't forget that this is a multiplexed device, so if you add 8 channels so the maximum you can set is 10 k/8

  If you are new to LabVIEW, I suggest that you try this sample program first

  \examples\DAQmx\Analog In\Measure voltage. llb\Acq & Graph tension-Int Clk.vi

  Amit

• Cannot connect Win 7 Ultimate to my secure WPA2 wireless network

  Any suggestions for how to connect to a wireless network secure n.   Currently running Win 7 Ultimate 64 bit and cannot get the sysytem works correctly?

  Hello

  Maybe this can help
  

  There is an inherent Catch22 to attempt to repair a computer wireless through wireless. Given that the without wire is not connected to the source, there is no interaction between the wireless source and the Wireless Client and no frame of reference to find what works and what does not.

  As a first step, I will temporarily move the computer to a place close to the wireless router and plug with a wire.

  When he works with a wire, switch Off the Wireless Security in the router, disconnect the wire and try to make wireless work. This must be done when the computer is always close to the wireless router to compensate for the weak, and or blocked the signal that could be part of the problem in the new suite spot work.

  In the computer itself.

  Most laptops have a physical switch for the wireless card. Read the manual of the computer and make sure that the wireless adapter is on.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• How to connect a HDD Momentus 5400.6 via a usb cable

  I am trying to recover data from an internal Momentus 5400.6 hard drive that was installed in a laptop ASUS who died recently. I connected the hard drive to another computer laptop pc under Win 7 sata to a usb cable. But when the system tried to install the driver that a failure has occurred. Through the Device Manager the drive appeared in the list of usb devices with an ASMT1051 tag, but with a yellow triangle with an exclamation point and the properties that "this device is not configured correctly. (Code 1) ». I tried to correct the problem by following a post suggesting to delete infcache.1 file in the c:\windows\system32\drivestore subdirectory and then restart and reinstall the hard drive, but that has not fixed the problem. Does anyone have any advice or suggestions on how to fix this problem?

  Hi again Isha,

  Thank you for continuing to read and answer all my dilemmas. My printer is a HP LaserJet 1100. The symptoms were it seems to load the driver ok, no harmful looking for signals through the Device Manager. When I printed a document if the print queue shows the document sent to the printer, but the printer just sitting there - no impression ensued. I tried attached to different usb ports, but nothing seemed to work. I noticed that there are 2 different printers available for printing of property. But neither the printers when selected would be to print a document. So I uninstalled the printer, rebooted and tried again. This time, it seemed to work ok. There was only a printer connected to the system and printed OK.

  I don't know if the condition to have 2 printers was caused by the setting of the printer on a different port or not.  I usually disconnect the printer until I need to print anything because of my 'office' layout So it appears I have my system back up and running as usual.

  Thanks again for the hand holding ;-)

• How to connect computer virtual machine host

  HI gurus,

  I have 2 internal hard drives in a PC. Primary (host) disc hard have win 2003 server and an SAP system, 2nd drive hard having (machine VMWARE) win server 2003 and another of SAP systems. I want to connect SAP through RFC systems. How to connect the 2 devices? What are all the steps needed to connect these 2 machines and 2 SAP systems? How to ensure that the connection has been established?

  Concerning

  Raja

  Your uses (host only) VMnet 1 and IP network address of the 192.168.174.0 network. Your host has the address of node of 192.168.174.1 in this network. You can see VMnet1 host IP configuration.

  To be able to get the two machines communicate with each other, the guest must have an IP address in the same network. You have two options here, where I would choose one to make sure that the address does not change in the future (better for SAP I think):

  1. assign a static IP address at the prompt.

  Go to your comments and change IP address of 200.200.200.20 to 192.168.174.2.

  2. use of VMWare DHCP Server service.

  By default, this service must be running. Go to theguest and choose DHCP in TCP/IP configuration. The client will automatically get an IP address of 192.168.174.0.

  Enter the following lines in the files 'hosts' of the two systems:

  192.168.174.1 ecc6.mycompany.com ecc6

  192.168.174.2 sapserver sapserver.mycompany.com

  Now try if the communication works: open a DOS window on the host computer, and run the command "ping 192.168.1.2. You should receive the prompt responses.

  Try to ping the host from the host by using 'ping 192.168.174.1' there.

  As long as this does not work, nothing else to Word the communications between two machines.

  If this works, you should be able to use shared folders using the names from the "hosts" file or IP addresses.

  For example:

  +
  ecc6\ +.

  +
  192.168.174.1\If you have found this information useful, please consider awarding points to 'Correct' or 'Useful' answers and answers. Thank you!!

• How to connect my i phone 6 to 10 on my computer windows

  How to connect my I Phone 6-10 Windows on my computer

  An iPhone will pair not via Bluetooth to a computer (Mac or Windows) with the exception of hotspot and then only if your cell phone plan he supports. See below for more information. https://discussions.Apple.com/docs/doc-7722

• How to connect to itunes for ipad airplay without using computer?

  HOW to CONNECT IPAD AIRPLAY to ITUNES WITHOUT the HELP of a FULL ❓l

  There is no need to shout. What you're trying to use AirPlay to stream content from your iPad to?

  Using AirPlay: How to use AirPlay on your iPhone, iPad or iPod touch - Apple Support.

  (I asked for your message to be moved to use iPad forum, where you have posted is for questions about the iTunes U app.)

• How to connect new IMac to old IMac to transfer files?

  I need to plug my June 2010 IMac in a new IMac 2016 to transfer data.  What cable do I and what ports should I use to connect?

  Thank you.

  Gina

  You can do it with an Ethernet cable (and on two Macs Ethernet ports) and use file sharing.  You can also connect via WiFi, but the transfer speed will be slower.  If both Mac connected to the Internet via a common router, you already have a link between two Macs.  Here is information on file sharing

  How to connect with the file sharing on your Mac - Apple Support

  There is also an automated tool called Migration Wizard, if duties are not suitable for your task

  Move your content to a new Mac - Apple Support

• How to connect a new MacBook in my time for the initial file transfer capsule

  How to connect a new MacBook to my existing time capsule to transfer files as part of the first implementation of my MacBook?

  You say that you have a new MacBook and that you have posted to the forum for the retina MacBook 12 "section, but your tag indicates that you have a MacBook Pro. Please specify.

• How to connect a drive to a 2015 iMac firewire external

  How to connect an external drive firewire to an iMac of 2015 for use with time machine?

  See love at first sight to FireWire adapter

  Apple Thunderbolt cables and adapters - Apple Support

• Want to 750-209: how to connect an old sound system to a new computer

  I wanted a new 750-209 and a former speaker of Cambridge Soundworks PCWorks 19th Point Surround 4 + under low voltage. There are 2 connector; Left and right who are article 3 (each take manages 3 drivers). The envy has 1 output. It seems that I need a derivation ending in female connectors.

  My question? How to connect the two? Is it still possible? I'd hate to have a decent sound system of junk. My needs are basic - just to be able to listen on AOL or YouTube.

  Any ideas on how to accomplsh my goal.

  Just to close this debate; unfortunaely the quick response has not responded to the problem. BestBuy has suggested that I try a composed of derivation of a shot and 2 containers. Finally, I got the system works 'after' discovery that the enormous power brick disliked the new arrangement of power when I replaced the old computer with the desire. I had to replace an adapter 3 - wat and consolidate the brick. A lot of noise to get her old system to work but now I have the choice of speakers or headphones driven by a hold on a HDMI monitor. All's well that ends well. Thanks for the interest.

• How to connect two computers and LAN

  I can't get my toshiba to interface with my desktop computer or to connect to the internet via a CAT5.
  I tried everything I know.

  I'm not too sure about the LAN MAC? He just will not connect even if the device is functioning properly.

  Any ideas?

  Here are the instructions how can connect the two computers.

  -First of all, you will need to disable the firewall.
  -Then you need to set the same workgroup on both computers
  -in the Lan Card Properties-> Protocol TCP/IP settings, you must assign the IP address manually. That is, a computer must use the 192.186.50.1 ip address and the other computer must be set to 192.186.50.2.
  -MAC address is fixed and cannot be changed. Each LAN card uses unique mac address

  After these settings, you must restart the portable computers (computers)

  PS: I recommend Google for details and further instructions.