How to read the Serial Arduino data using labview VISA?

Similar Questions

• How to read the tag bluetooth data in labview 2015 running on Windows 10

  Hi all

  I have a Development Board Nordic semiconductor nr51. This card is programmed as a tag bluetooth which simply announces his address with 16 bits of data appended to the end.

  My laptop came with loan materials smart bluetooth. I installed an app interactor lighthouse to bluetooth on my laptop and the software is able to detect the tag as if shown on the image below.

  

  I wanted to write a LabVIEW program that will simply be careful bluetooth headlights and notify me in my computer every time a lighthouse with the specified address is detected. This mobile application below is provided by the manufactuerer of the Board of Directors and I wanted to develop a LabVIEW program something similar to what will read the given data and extract values.

  

  Somehow, all the sample applications provided data only shows how to read and write in a connected bletooth device but not analysis for tags. I also tried using the Bluetooth ' discover ' and it does not detect the bluetooth beacons.

  Could someone provide me with the necessary information or example program for detecting / reading of tags bluetooth in LabVIEW 2015 running on Windows 10?

  Do I need to install a third-party software to read data from bluetooth?

  Bluetooth in LabVIEW function nodes using the Winsock interface to access bluetooth resources. This works very well for Bluetooth 2.0 devices but not Bluetooth 4.0 devices WHEAT aka. Microsoft has created a completely different interface for these resources API as the model of overall service for WHEAT devices has radically changed.

  The API to use WHEAT devices is the API of the GATT (generic attribute profile) in Windows. There is supposedly a .net interface available that you can try to use (Windows.Devices.Bluetooth.GenericAttributeProfile). The WinAPI to lower level (https://msdn.microsoft.com/en-us/library/windows/hardware/hh450825(v=vs.85).aspx) is a C DLL API and does not lend at all to be called directly by the LabVIEW call library node, since some of the parameters of the function are quite complicated and you need to also access the SetupDI APIs to enumerate resources WHEAT and even harder to function parameters. In order to access this low-level API to write an intermediate DLL which results in low level API C a more acceptable API for LabVIEW.

  Another possible problem is that Windows don't at least in Windows 8 not allows devices to pair per program. Microsoft wanted to force developers in the use of the "inbox" experience, which means that all users must go through Microsoft provided service pairing, instead of each request for implementation of his own matching technique.

• How to read the digital I/o using PXI-7813R?

  Hi guys,.

  I'm reading a digital signal by using one of the ports in the PXI-7813R. The 7813R has 5 digital ports or 39 lines for playback of digital data. I have connected a SCB-68 as the physical hardware interface for 'plug-in' a 5V adapter, which will act as my signal at the moment.

  After you configure the PXI via MAX, I wrote two codes, one for my host pc and the other to control the FPGA through the host. But I think, I can have more complicated or completely gone in the wrong direction.

  Any help in the drafting of these codes would be well appreciaetd.

  Thank you, Anoop

  You need the FPGA to sample the signal how often you expect the device to send the data.

  If you write your data in the FPGA for the DMA, then on the side PC you just have to read the DMA.  I like to think of the DMA as a queue.  It makes it easier for me to understand how it works.

• read the serial port management using the SRM Protocol

  Hello

  I have a gas analyzer that communicates with the PC via the serial port.

  This is the "Industrial VarioPlus SRM".

  I have attached a PDF file that describes the communication protocol.

  I'm trying to decode the data that are sent from the parser, but I can't do it.

  I have attached the vi in which I made some effort.

  Any help is appreciated, at least for a single value in the data stream.

  Thank you.

  
  

• How to select the path of data through labview

  Hello gurus...
  I'm new user in labview. I want to read and write to the database via labivew. I have
  read and write the program. Now, I want to choose the way of storage of data through labview.
  I tried different ways, but I couldn't.
  First of all read and write the program I did via the UDL file path. Now, I want to choose ".mdb" file path directly.

  I do not know how...
  So if you know please help me...
  Thanks

  Concerning
  Joel M
  India

  Rather than trying to create an Access database, I have simply included a blank database with the installation.  Open, build the tables as required (as your example shows), and then copy (using the copy of the palette of Advanced File i/o) whenever you need it.  Your program will need to know where it is, therefore, store the connection information in a configuration file (as already mentioned) is a possibility.

  Here's how to use a connection string to open a database:

  

• How to get the PC host name using labview

  Hello

  I have a need to display the name of the host (login name) pc in my application. How do I get using labview in DURATION that is if I write a program and run it in different systems of PC / same system with different users, so I should get corresponding logins.

  Can someone help me on this?

  Thank you

  Kind regards

  DEGHA

  

  Should be available in LV RTE

• How to read the heart rate data recorded by the Apple Watch?

  My wife wears a Apple Watch and suffer from power cuts irregulars. After the last of them, I checked the data through the health app and saw that at the time of the blackout, there seems to be no saved data. A range of heart rate was recorded both before and after the blackout. Can someone explain how the data record? Thank you

  MIchael Gilmore

  This explains the various triggers causing the heart rate measure:

  Measure your heart rate with your Apple Watch - Apple Support

  Here is some additional information:

  Your heart rate. What it means, and where on Apple Watch you will find. -Apple Support

• Read the PXI-8431 channels using LabVIEW

  
  

  Hi Marc,

  The examples provided with LabVIEW and DAQmx drivers are very detailed and comprehensive to demonstrate how you can use cards. To join the Finder of the example, start LabVIEW and select help > find examples.

  When you load the example Finder, make sure you browse by task.

  For the programming of DIO:
  Navigate to hardware input and output > DAQmx > digital measurement. There is a few screws. Make sure you look in the list of requirements to see the example works with the PXI-6515.

  You can also visit the following links to learn more about programming DAQmx:
  Getting started with NO-DAQmx
  http://zone.NI.com/DevZone/CDA/tut/p/ID/5434
  Learn 10 functions in NOR-DAQmx and handle 80% of your Applications of Data Acquisition
  http://zone.NI.com/DevZone/CDA/tut/p/ID/2835

  For series programming:
  Navigate to hardware input and output > Serial
  You will find most of the screw example it can be used with the PXI-8431.

  I hope that helps you to get off the ground!

• Read the serial number of the PXI 8130

  Hello:

  Anyone know how to read the serial number of an SMU-8130 chassis controller programmatically? Read the serial number of a 1075 chassis will work also.

  Is it still possible?

  Thank you very much

  -Ilya.

  My apologies, as this thread is expanded to LabVIEW, I was assuming that the main language was LabVIEW. Currently, it is not a condition C library that reproduced the personality of the Configuration of the system. My understanding is that this feature is in the works, but not yet implemented.

  In the short term, you can choose to compile the necessary features of LabVIEW in a DLL called by your project. Otherwise, the MAC address can still be used as a unique identifier, if that's what you need.

  See you soon,.

• Sometimes the lost bytes, reading the serial port

  Hello!

  I'm reading the serial port data (flow rate 57600 baud rate) that works very reliable so that I do not open any other window

  or minimize/restore my window of the application during the program is running. Then a byte of incoming data will be lost.

  I get a string of 30 bytes each 50 m in most of the cases the first byte is lost, sometimes one in the middle.

  This occurs not only on a PC.

  Is this a problem of LabVIEW or Windows?

  Are there settings that can solve the problem?

  Best regards

  JK78

  I solved the problem.  

  There was a bug in my program who become visible only if a window has been reduced or restored.

  When there are two or more messages in the buffer VISA, the separation of the messages was incorrect.

  Array index corresponded to false so that the first byte of the second message was at the end of the first

  and so the second message in the buffer seemed incomplete.

  In normal operation, the playback loop runs so fast, never both messages are in the buffer.

  Thanks for all replies.

  JK78

  Either way, I work with LabVIEW 2009 and serial interface hardware motherboard. With XON/XOFF flow control

  is not possible in my application because all the hex values from 00 h to FFh may appear in a message.

• How to read the data from a channel named in windows using labview

  Hello

  I need to read the channel named in windows data. The pipe is created by python by another application. This application post permanent data on the pipe. But I don't know how to read data using labview. is it possible to read the data from different application? If possible, how to start?

  Thanks in advance

  concerning

  RJ

  Hi Rolf,.

  It's just, because of driving is not initialized completely, pipe read returns error 42, I added 2 seconds late, then its work perfect.

  Thank you very much.

  Concerning

  RJ

• you want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. A

  I want to send data using labVIEW to arduino using write visa and the process and to take action using arduino. After that, I want to arduino to send out necessary via a serial port to labVIEW which should be read using visa read and store in a chain. While I am able to write or read both individually, I can't do it consecutively. I used advanced read and write vi for checking my code, but nothing is helping. The wrong bed 'time delay before execution. " Please let me know where I can go wrong. Also is it possible to write code for hx711 using labVIEW

  1. you need not "\n" on your orders println().  This command adds an end of line character already in the message.

  2. you get the error because you have a loop around your reading.  After the first reading (well technically, the second because of you add an extra line end character), there is nothing left in the port.  As a result, you will get the timeout.

  3. you should really consider using a Structure of the event.  This way you just don't write and read when you press the Write button and you can also use the structure of the event to make the loop to stop.  I also go up to close the port inside the stop-> value Change event.

  

• How to read the two columns of data from the Port series

  Hello

  I'm reading two columns of data from the serial port.

  Example:

  52439 52430

  52440 52437

  52209 52214

  51065 51070

  52206 52390

  I use the serial of Visa service and I can read the first column of data from the serial port, but I can't understand how to read the second column.

  I want to both sets of chart data.

  I enclose my VI.

  Thank you for your help.

  The analysis of string function takes a "Format string" on top (with the right button of the function and choose Help, which explains all the entries).  In particular, you can say 'Give me two numbers separated by a tab' and the output will be two numbers (whole or floating, depending on the chosen format).  In particular, %d\t%d specifies a decimal integer, , whole decimal.

• How to read the data in a device connected to the usb port

  Is there a class or object, or the piece of code in Java that is comparable to the PDQComm32.ocx and the mscomm32.ocx used in VB6? I need to know how to read the data of a device plugged into the usb port of the BBerry. Is it possible to use the BB to read data from a device via a usb cable?

  I'm new in Java and I'm looking for the opportunity to write a project to read the data in a device with this program that can turn on a BB instead of on a pc.

  Thank you

  Did you watch net.rim.device.api.system.USBPort?

  That's what the doc says:

  Provides access to the USB port of the device.

  Avoid using this class in applications, as it is not portable. On the contrary, if you need to access the USB port, use factory CLDC Connector to serve a connection.

  Rab

• How to read the date and time of a file by labview information

  How to read the date and time of a file by labview information? for example, time created and updated time.

  The similar question had already spoken here (this is the old thread but still seems topical):

  http://forums.NI.com/T5/LabVIEW/file-date-created/TD-p/109836