How to read the digital I/o using PXI-7813R?

Similar Questions

• How to read the digital square wave pulses

  Hello

  I recently bought a blue-white meter. I have successfully read the digital square wave from the sensor. However, I face a problem to calculate the flow rate and the total volume of liquid. Can someone help me with this?

  Technical data of the flowmeter can be access to the http://www.blue-white.com/Products/ElectronicFlow/MicroFlo/80000-406_microflo.pdf. And the calculation can be found on page 9. I use NI9401.

  Thank you

  
  

• How to read the Serial Arduino data using labview VISA?

  Hi =). Im a beginner work reading data series from an arduino but im facing... Lets do it step by step

  I built a voltage divider circuit which gives from output
  from 0 to 5V. The output of this circuit is sent to a 0 analog input pin
  of a Committee of Arduino Duemilanove.

  (1) Firstly, I connected the cable to connect to my laptop USB the Arduino.

  (2) I went to start-> control
  Control Panel-> system-> hardware-> Device Manager. Check the Ports (COM
  & LPT). In my laptop I can see USB Serial Port (COM4). Now I know only in
  LabVIEW that I must read the data series COM 4.

  (3) to the side of the arduino, here's the code to read changes in voltage
  entered to analog pin 0. The last line of 'delay' determines the sampling
  Rate of how we want to taste the output of the voltage divider:

  int potPin = 0;    Select the input pin for the output of the voltage divider
  int val = 0;       variable to store the value from the probe

  void setup()
  {
  Serial.begin(9600) (9600);    Opens the serial port, establishes the rate of 9600 bps data
  }

  void loop() {}
  Val = analogRead (potPin); read the value of the voltage divider
  Serial.println (Val);
  Delay (10);
  }

  I slightly modified the basis series reading writing VI... I have
  attached the block schema used with comments. Basically, I tried to read
  data series, divide by 1023 and multiply by 5 to graphic voltage
  variations of the voltage divider circuit.  But Im not getting
  the correct voltage output values. The value of the tension just keeps go
  0 and coming again, as shown in the photo.

  Could you guys please guide me on what went wrong?

  Thank you!

  -you read the data, even if there is no data on the port. If 0 bytes are read => «»

  -in the case of false, you resources VISA wired for the output of channel tunnel?

  -There is no close VISA at the end of the VI resources

  -you're not a loop this VI reading bytes

  I added an addaption of your VI that you should give a try maybe

• How to read the files on time capsule

  How to read the files on time capsule from iPad?

  Thank you

  Using an application like navigation on the iPad. More info here:

  Stratospherix - FileBrowser - overview

• How to read the status of User1 DIP-switch with a cRIO FPGA chassis?

  How to read the State of the DIP switches on a FPGA cRio chassis?

  I work with a cRIO 9022... My idea is to put the system in "service" mode with USER1 switch to IT and communicate with the FPGA via the FPGA - GUI (VI) on the host computer instead via the RT module that is used in normal conditions.

  Any ideas? Unfortunately, I don't have an unused channel on the left... .and (as I know) cannot use the interface RS232 of FPGA.

  Many thanks in advance,

  Luke

  Hi, this is the correct information. You cannot read the FPGA of DIP-switch status. The only thing you could do is to use the function of Reading Switch.vi located under the range of functions-> real-> utilities RT time

  It's how you probably know side host RT and not the FPGA.

  Cordially Virginia

• How to read the two columns of data from the Port series

  Hello

  I'm reading two columns of data from the serial port.

  Example:

  52439 52430

  52440 52437

  52209 52214

  51065 51070

  52206 52390

  I use the serial of Visa service and I can read the first column of data from the serial port, but I can't understand how to read the second column.

  I want to both sets of chart data.

  I enclose my VI.

  Thank you for your help.

  The analysis of string function takes a "Format string" on top (with the right button of the function and choose Help, which explains all the entries).  In particular, you can say 'Give me two numbers separated by a tab' and the output will be two numbers (whole or floating, depending on the chosen format).  In particular, %d\t%d specifies a decimal integer, , whole decimal.

• How to read the 32-bit depth .bmp image

  How to read the image, 32-bit depth using LabVIEW .bmp?

  
  

• How to read the analog inputs of one Board of R for (PXI-7851R) series

  You can guide me please with the steps for reading of the analog inputs of a series a. card I use as the target fpga PXI-7851R.

  Have you looked at the examples provided with LabVIEW? There are examples showing how to read the analog inputs.

• Don't know how to read the results of netstat EI s list? If I received 860592506 bytes sent from 43421482 how to convert MB? And does this mean byte received?

  Don't know how to read the results of netstat EI s list? If I received 860592506 bytes sent from 43421482 how to convert MB? And does this mean byte received?

  Hello

  This shows the total number of bytes transmitted and received via the Ethernet card. This is the total of the amount of use up to this day.

  This includes all the Web sites you have visited and emails you sent, etc..

  You can calculate using one of the following methods:

  Method 1:

  860592506 / 1048576 = 820,72 MB

  Method 2:

  Multiply 860592506 with 9.53674316 * 10 ^-7 that will give us the result in mega bytes.

  860592506 bytes = 820 MB 9MB not, accept my apology for the miscalculation.
  Similarly 43421482 acroos = 40MB

• How to read the data in a device connected to the usb port

  Is there a class or object, or the piece of code in Java that is comparable to the PDQComm32.ocx and the mscomm32.ocx used in VB6? I need to know how to read the data of a device plugged into the usb port of the BBerry. Is it possible to use the BB to read data from a device via a usb cable?

  I'm new in Java and I'm looking for the opportunity to write a project to read the data in a device with this program that can turn on a BB instead of on a pc.

  Thank you

  Did you watch net.rim.device.api.system.USBPort?

  That's what the doc says:

  Provides access to the USB port of the device.

  Avoid using this class in applications, as it is not portable. On the contrary, if you need to access the USB port, use factory CLDC Connector to serve a connection.

  Rab

• How to read the values of the field of LOV disabled?

  Hi all

  I have a requirement, based on values that we entered one of the LOV fields, then we are arising from the new values based on the value that we entered this field of LOV. And then I must by default new LOV values derived in a two other fields of LOV and then disable them. Once the fields are disabled, then I'm not able to read the values using the pagecontext.getparameter... I get nothing when I tried to read using the pagecontext.getparameter.

  Pointers on how to read the values of disabled field/LOV?

  Thank you
  Clarriiza

  1. you already have values, and that's what you set in the LOV before turning off, right? So why do you need to recover again from the LOV.

  2. are you disabling or making it readonly? I think that if it is disabled, you might still be able to get the value using pageContext.getParameter.

  3 have you tried to get the handle to the LOV bean and get the value using lovBean.getValue (pageContext)?

  4. another Option is to combine the value of a FormValue Bean also (as well as the LOV bean) and retrieve it from FormValue.

  5 BTW, why are, why you're seen LOV if you disable it? Can't you just a TextBox?

  See you soon

  AJ

• How to remove the digital ID

  I have a digital ID in Adobe Reader X and forgot my password.  Because I don't believe that these passwords are recoverable, I need to delete the codes and start again.  But when I go to edit, then the protection window that opens is very light and I can draw anything to the top of this window. Can someone help me this this please?

  Hi GlendaKay,

  Please take a look at this thread: How to remove the digital ID in Acrobat 9 Pro Extended?

  Thank you

  Abhishek

• How to remove the variable created when using definedNamedWhereClauseParam()

  Hello
  
  My Jdev version 11.1.1.7.0.
  
  I'm Executive where clause programatically where I need to bind two bind parameters under certain conditions. Example, I have two bind variables X, Y.
  
  Here's the problem:
  
  Assume that the first time I'm setting one variable X, so I define X bind variable and execute the query.
  
  What second time I send only Y but not X. In this implementation of the scenario of VO throw an exception, given that the variable X is already created in the VO object and where clause does not have this setting.
  
  So how to remove variables created in the original Version all in definedNamedWhereClauseParam(). I need to erase what ever the previously created variable every time I execute method.
  
  I can make the similar functionlity using setWhereClauseParam (using literals). But I have a few technical restrictions for use.
  
  Could you please help me how to remove the variable before vo using definedNamedWhereClauseParam.
  
  Caused by: java.sql.SQLException: try to set a parameter name that does not intervene in the SQL: itemNumber
  at oracle.jdbc.driver.OraclePreparedStatement.setObjectAtName(OraclePreparedStatement.java:15969)
  at oracle.jdbc.driver.OraclePreparedStatementWrapper.setObjectAtName(OraclePreparedStatementWrapper.java:911)
  at weblogic.jdbc.wrapper.PreparedStatement_oracle_jdbc_driver_OraclePreparedStatementWrapper.setObjectAtName (unknown Source)
  at oracle.jbo.server.OracleSQLBuilderImpl.bindParamValue(OracleSQLBuilderImpl.java:4669)
  at oracle.jbo.server.BaseSQLBuilderImpl.bindParametersForStmt(BaseSQLBuilderImpl.java:3687)
  at oracle.jbo.server.ViewObjectImpl.bindParametersForCollection(ViewObjectImpl.java:22742)
  at oracle.jbo.server.QueryCollection.buildResultSet(QueryCollection.java:1298)
  ... more than 96
  
  
  
  Thank you.
  
  -Diette.
  
  Published by: Vidya Diette on February 28, 2013 08:43

  Hello

  You need access to the variable Manager. Order of reading in the JavaDocs:

  http://docs.Oracle.com/CD/E28389_01/apirefs.1111/e10653/Oracle/JBO/ViewObject.html--> http://docs.oracle.com/cd/E28389_01/apirefs.1111/e10653/oracle/jbo/VariableManagerOwnerBase.html#getVariableManager%28%29--> http://docs.oracle.com/cd/E28389_01/apirefs.1111/e10653/oracle/jbo/VariableValueManager.html--> http://docs.oracle.com/cd/E28389_01/apirefs.1111/e10653/oracle/jbo/VariableManager.html#removeVariable%28java.lang.String%29

  Frank

• How to read the value of an independent textInput element inside the method?

  Hello
  
  I had a group of detail based on a readonly viewobject. I added an independent element textInput, you say, EndDate to this group that the user can enter a value inside. Now, when I run the app I select a row in the table and press a button that triggers a method inside a bean. My question is how I read the value in independent textInput (EndDate) within the method element?
  
  getTable () .getRowData () does not print the unbound attribute. It seems that it only contains attributes underlying viewobject
  
  I use JDev 11.1.1.4
  
  Kind regards
  Will do

  Will do,

  You can better create a transitional attribute for that in your view object, so you can use a regular expression #{row.bindings...} to get the value.

  Steven Davelaar,
  JHeadstart team.

• How to manage the photos Lightroom when using 2 computers, keeping any changes made on one or the other?

  Based on http://forums.Adobe.com/thread/1308132?TSTART=0 I decided to add each question separately:

  Hello, I am very interested in buying Lightroom 5.2. I tried the RC that was missing today. Yet, I have several questions that I can't find really good conclusive answers, I'd like to get an answer before buying LR. Please do not write maybe like this or that (assumptions), because I don't want to start my entire workflow and then realize that I have to change all around, please reply, if you know for sure that something works and you are, preferably, using this method too.

  Is the big question, where I want to especially a conclusive answer:  How to manage the photos Lightroom when using 2 computers, keeping all the changes made on one of them, using the same photos for editing. I'm not going to use DNG. Details: I mainly use my old MacBook Pro, but I wish I could use my PC as it is much better (card: i5 2500K, 16 GB of RAM, SSD, USB3, nVidia GTX 560 TI etc.). I have 2 external HD that I could use, one for backup and one for the actual Photos/changes. I you will probably need to use as my internal HDs are fairly complete and I cannot be the kind of things simply delete or move to one (developer, without loss of music, programs etc.).

  On this basis, how do I save all such Photos folder (pictures and retouching and preferably presets too)?

  According to me, that it should be possible to work cross-platform without having to create a link to the files each time, or without having to keep export/import of the catalog, keeping the single catalog and the picture library on an external drive that is then switched between systems as needed.

  Obvious first requirement is an external drive that is formatted in a way (for example, FAT32) that it can be used on both platforms in read/write mode. Given that, if the catalogue AND folder parent si le catalogue ET le dossier parent images are both set to the same level in a global parent folder, then it should be possible to take advatage of ability of Lightroom to use relative paths instead of absolute paths to detect the images, no matter if the player is named (Mac) or lettering (PC). This is how "export as catalog of ' works, that is, it creates a 'package', alias a parent folder, containing the catalog and a replica of the folder hierarchy to exported along with the catalog images. Take this 'package' to another system (same OS or not) and "it works" even if the drive letter is different or the operating system is different... because the relative path of the image catalogue is always the same.

  I have not tested this cross-platform (if I have between various PC systems with letters of different readers) so for me it's still just a theory, but there may be others who have done this successfully.