HP Pavilion a6552f Desktop will not start - almost tried everything

Similar Questions

• HP P6280 desktop will not start

  Hardware: HP Desktop, 2.5 Ghz/6 GB RAM 6280

  Software: Windows 7 Home Premium

  Symptom: Slider, upper left corner flashing. Will not start windows. Does not start the system recovery

  Tests: will start at diagnosis; all components are

  Visual: all current fans running, hard drive access light blinks.

  Tried:

  1. how to remove the card reader and re - start with a statement found here. No change

  2. removed the hard drive and connected to another computer via the USB interface. The road climbs and all the folders/files are present

  3. re-installed the hard drive and the boot order changed to search first of hard drive. Still no change.

  Question: Do you think a FIXBOOT is possible hard disk using a different computer with the hard drive via the USB interface?

  Any other suggestions would be appreciated.

  Hello

  Please use the following link

  http://h30434.www3.HP.com/T5/desktop-operating-systems-e-g-Windows-8-software-recovery/black-screen-w-blinking-cursor/TD-p/1330837

• Pavilion ID46 g6 will not start

  Product: Pavillion g6 ID46

  [Edited by Moderator] Serial No.

  Product # A6Z74UA #ABA

  OP sys: Windows 7 Home Prem OA

  Pavillion G6 my husband will not start. What happened: returned to the computer after being away for a while, shook the wake up the mouse and the screen «has exploded in many colors and motion pixels» Screen went black, then a screen "do you want to start in safe mode" popped up. He tried a start-up without danger, but he failed and gave him a Bios Application error 501. He tried to restart the computer, but it crashes on the 'Starting Windows' screen with 4 color icon.

  I have:

  Removed the battery and tried to restart. Not good.

  Has taken the hard disk and and reinstalled it. Ditto.

  Tried to boot mode safe, before and after the following below. "Loading files" still stuck on Windows\System32\drivers\CLASSPNP. SYS

  Burned and ran a repair disc. Took 4 hours and the program ran at the end when I was asked to reboot. Computer hooked on "Starting Windows" screen. (I left this screen function for more than 5 hours without this change.)

  Ran the program System Repair twice, same results.

  Start of Tests ran. After self-test of the main hard drive, hard drive SMART and verification Test of memory system (passed 100%)

  Tried to restore the BIOS using Windows + B and power with several attempts. Button Power LED stays on, about 20 seconds later a small LED on the "caps lock" key flashes white twice. Black screen and nothing happens after 5 minutes. He raised his eyes and 2 flashes is supposed to be the corruption of the BIOS.

  Error log lists these: quick 03F0 303, 501 error and error of hard disk 1.

  I have a lot of intelligence of the computer, so appreciate any help you can give, especially if assistance is simple and easy to follow terms.

  Mahalo in advance!

  Well, nothing worked and I did not attempt to remove the HD and turn it on again. Husband returned to a comp sci student who managed to get some info on the HD, but said that the HD was shot.

  Good thing is that I got a new Asus laptop and put my old computer to my dear husband. So, I guess that the problem is solved!  Thanks for your help.

• FOR SOME REASON, MY WIFE LOST BOOTMGR AND HIS NETBOOK WILL NOT START I TRIED TO OBTAIN DE FACTO

  FOR SOME REASON, MY WIFE LOST HER NETBOOK HP BOOTMGR AND IT WILL NOT START I HAVE TRIED TO GET THE FACTORY SETTINGS, BUT IT WILL NOT DO THAT CAN HELP YOU

  
  

• Dimension 4700 desktop will not start

  I have a Dimension 4700 desktop computer that has been sitting in storage for a while. I wanted to start and see is there something to this subject that I had to save or erase the hard drive. As far as I know, it was working fine when it was put away. Now it won't start at all. Here is what I know-

  Dimension 4700

  Service etiquette: ADMIN NOTE: Service tag deleted by privacy policy >

  running Windows XP Home Edition

  Power light turns on and remains lit (green). DVD players do a rotation test (but will not read a boot disk). The hard drive light comes on and stays on.

  Does NOT display a Dell spash screen. The screen is blank (black) with the exception of a simple white flashing cursor (line underscore). It crashes in this condition.

  Does not meet the keyboard commands (ctl + alt + del, esc, f8, f11... etc.). Does not respond to reset (press power button in disable).

  Diagnostic lights are lit on the rear panel. A, B, C are all stable and green. D is amber and regular.

  All inner and peripheral cables seem to be properly fixed.

  When the power to the hard drive cable is removed, it does NOT POST beeps (the condition is the same).

  I can't get to the Setup screen. I can't boot from a cd. I don't get any sound signals (beeps).

  It is out of warranty, and troubleshooting knowledge base sent in a recursive loop items that never exceeded the step #2. Someone at - it suggestions?

  Because it has been stored for a while, first stage, with the PC off, is to reinstall (unplug then plug back in) all the memory, PCI cards such as video, sound, etc. and all cable connectors.  Make sure that when you plug the points back in that you get fully and correctly reinstalled.     Back off and see if that makes a difference.

• HP Pavilion dv5z-1200 will not start, flashing LEDs

  LEDs keep blinking once every 4-5 seconds, computer does not start even in the BIOS.  Out of warranty.  The table shows the CPU is not functional.  After the hard reset several times, after the failure of the CMOS, I reinstalled the memory modules, nothing helps.  I opened the darn thing, reinstall the CPU, cleaned the existing thermal paste and replaced with a high thermal conductivity, one and clean thermal gel pads ugly that supposedly provide a cooling the GPU.  All this for nothing.

  Should I assume by now that the CPU is fried, or is there a chance to distance the BIOS EPROM chip is toast and cause all this?  Someone has experience in this sense, is the flashing model good to locate the faulty component?  All ready to offer their advice Jan 11-12 HP Expert?  I replaced a BIOS chip in an another HP Pavilion of last spring, so it wouldn't be a problem.  Don't want to invest all efforts - and paste - for nothing.

  In any case, this is / was my last HP laptop ever.  Between a ze4547 and this dv5z, I got so of many hardware problems, I prefer to buy netbooks cheap every two years than spend a zillion things expensive, shiny, flashy with abject genius inside.

  Thanks in advance to anyone!

  Taking up this issue and reported a permanent fix (i.e., more than 5 months).  Yet once, the defect could not solder in the graphics chip ATI Radeon (Northbridge).

  Chip HP ships this with a simple gel pad main Board between the radiator and the graphics, which after > 1 year of running hot develops inclusions of air and turns of conductor of heat a heat insulator.  Due to the high temperature resistance, brazing under the chip will slowly oxidize anr / or crystallize and develop cracks and inclusions of oxide.  The only solution in addition to buying a new card of mother is reinvest with a heat gun, or using a special station of redistribution and the improvement of heat transfer to the heatsink.

  Here's what the complete repair consists of:

  -Disassemble the laptop according to the instructions in the maintenance manual; Make sure that keep track of where each screw came from

  -Remove the heat sink fan and clean the end inside of the metal fins (simply by blowing canned air will not work)

  -cut a ~ 1 mm of thickness copper thick to the exact dimensions of the cushion gel covering the ATI Radeon chip and ensure its two surfaces are clear of any oxide

  -Clean the CPU and the Radeon perfectly cooling surfaces using 92% isopropyl alcohol; in a similar way to wipe the corresponding surfaces of the shiny heatsink

  -dissolve welding flow or Rosin in a few mL of 92% + isopropanol

  -pour a few drops of this solution of rosin under the chip Radeon on all 4 sides; Rosin ensures that reinvest the chip will recreate connections free of oxide with the main card; use a pipette or a pair of tweezers for this and not to spill the solution outside the area of interest

  -make a mask cardboard lined with aluminum for the entire main Board having a place of opening in the Center exactly as big as the Radeon chip; Make sure that the coating of aluminum foil extends to the lower part of the mask through the operning square to protect the card against high temperatures. use this youtube video as a guide (minute 06:50)

  -heat gun to regular heat on 'Medium' (or 'Low' if only two power settings); taking the mask in place immediately on top of the Radeon chip using a tool metal long (so you do not burn your fingers), slowly heat by lowering the gun hot air for the duration of a minute

  -maintain the hot graphics chip for about 30 seconds into the air gun hot about 1-2 inches above the chip. Make sure that the mask with double foil is aligned with the chip to avoid burning its below or other components of the motherboard; consider wearing a thermal glove or leather on the hand that holds the mask down with this tool metal long

  -slowly raise the heat gun on the time of ~ 30 seconds and then remove the mask and let the chip and the main map to cool for about 1-2 minutes

  -It is best to test repair before reassembly of the computer; to do this, connect the power button, display, cooling fan, a single chip of RAM and a charged battery to the main card and turn on the laptop the bone bare; See the HP logo on the screen for a success to reinvest

  -use of money from high-quality thermal compound (for example, Arctic Silver 5) and coat the surfaces of cooling of the CPU and Radeon chip, as well as the corresponding surfaces on the heatsink of heat and the puck in copper, with one layer, thin and uniform; Wipe all spilled; Place the wedge of copper on the graphics chip and carefully assemble the heat sink; don't forget to plug the fan on the main card

  -Finally, back up the phone by following the steps for disassembly in reverse order; do not mix the screws, like using a long screw where it was not may cause a short circuit or cracks in the main map

  -Use of SpeedFan to monitor the performance of you cooling system in the processor; periodically blow out or spend vacuuming of dust between the cooling fins.

  Good luck to lovers!

• HP Pavilion DV6-3060em will not start

  Hello! Today I buy new USB mouse (Logitech Gaming G100s) and my laptop does not start. I turn on and the screen is black. Everything is OK, when I unplung this mouse, it starts normally. Somewho can help me? Thanks, sorry for my bad English, I'm Slovenian.

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  According to the message that you posted, I suspect that this could be due to the recent changes are applicable

  Please perform the steps to solve the problem below:

  Step 01. Turn off the computer

  Step 02. Turn on the PC and keep pressing the F8 key

  Step 03. Select "Last known good configuration" in the list of the early start Option

  Note: Wait until you get to the Windows desktop

  Step 04. Please remove unwanted startup items and uninstall unwanted applications

  Step 05. Please reboot / restart your PC normally

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  Although I am an employee of HP, I speak for myself and not for HP

• Pavilion dv9810us: computer HP Pavilion dv9810us laptop will not start

  Reminder: a few days before my laptop does not start up, all using the laptop, the screen has become, I guess the technical term would be 'nuts': horizontal lines an inch in height, made of blocks quickly black and white, all changing left and right, and I could see my spreadsheet in the background.  Could not do something about the problem, so I rebooted and it worked fine.

  Then a few days after that, I tried to turn on my laptop, and occurred the following:

  (1) blue illuminated switch, control all the keys lit in blue (volume, skip, repeat, DVD...), fan began and heard the dvd begins to check for a disc.  This lasted for about 2 seconds.

  (2) off laptop (all lights extinguished, no fan noise or a dvd).  This lasted for about 5 seconds.

  then it would just repeat steps 1 & 2 times: start 2 seconds, stop for 5...

  Steps that my work to correct (without success):

  -J' I disconnected and removed the battery.  Let stand a few minutes.  After I have inserted the battery and reconnected, I pressed the power button.  Same 2 steps as shown above (lit for 2 seconds, turn off for 5, repetition) happened.

  -saw a post on the site of HP on a hard reset.  so I unplugged, removed the battery, which is held from the Start button / stop for 20 seconds.  then replugged (without inserting the battery) and power on.  Same 2 steps above happened (lit for 2 seconds, off for 5, repetition...).

  -J' I reset memory as someone on the HP Board has suggested:

  (1) remove the two memory, then replace both in the correct order.

  Result: same problem (2 seconds 5 seconds, repeat...)

  (2) remove the top memory (1 GB), bottom (2 GB) by leaving in place.

  Result: same problem...

  (3) place 1 GB memory on the bottom, nothing over the top.

  Result: same problem...

  From the above information, no idea what the source of the problem is, and how to fix it?

  It would be to remove the motherboard and "re-invest" the video chip with a heat gun. Configure you with a shield from sheet aluminium with the chip pushing through like dessert in a TV dinner. There are many tutorials online, but like anything else go you better the more you do and the first time is risky. Repair shops using a better process called "reballing", which is basically rebuild the chip and requires hardware, that no individual can afford to have.

  Access to the old hard drive is easy. Physically, remove it from the machine.

  https://www.YouTube.com/watch?v=B3tAGVzCS7w

  See 02:20 in. You must remove the plastic adapter for in standard SATA ports. You can leave it in the basket after removing the plastic adapter bar. Then use a usb to SATA adapter and you can plug the old drive on USB ports on your computer again, and it will appear as a USB key where you can copy and paste things out of it to the new PC.

  http://www.Amazon.com/STARTech-com-SATA-drive-adapter-cable/DP/B00HJZJI84/ref=sr_1_1?ie=UTF8&QID=1432146725&SR=8-1&keywords=USB+to+SATA

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• MY hp pavilion dv7 - 1247cl will not start until it say BOOTMGR is missing.

  Original title: I have a laptop hp pavilion dv7 - 1247cl which cannot start it say BOOTMGR is missing, can you help me please?

  I WAS ABOUT TO ERASE THE DATA AND THE LAPTOP WAS DISCONNECTED SO NOW CANNOT START UP

  Hello

   

  1. what operating system is installed on the computer?

  2. What is the full error message?

  3. using a program to erase data?

  4. have you already tried booting in Safe Mode?

  See the following article:

  Windows error message «Bootmgr is missing Press Ctrl + Alt + Delete to restart»

  http://support.Microsoft.com/kb/2622803

• OSX Yosemite - Flash Player will not even install - tried everything (I think!)

  I've tried everything. I have a new MacBook Pro with Yosemite 10.10

  I downloaded all Adobe Flash Player installation file that says will work with the latest Mac system, but it bounces right on the dock. I finally found one that actually opens a window of Setup, but when I click on 'Install' the beachball weaves, let him shoot all day today to see if the time would help. He just kept spinning as if it were really long Beach Boys concert.

  Please, someone help. All with the video seems to use it. I had this problem for the both Safari AND Firefox.

  Great, glad you were able to get running.  Usually when you see this, it's a third-party virus scanner - usually a release or off-brand a - which is to stop the installation program.  If you want to help us improve Setup online, newspapers would be useful.  Otherwise, we keep links updated for offline installation programs displayed on the installation troubleshooting guide.

  https://helpx.Adobe.com/Flash-Player/KB/installation-problems-Flash-Player-Windows.html

  https://helpx.Adobe.com/Flash-Player/KB/installation-problems-Flash-Player-Mac.html

  As this original thread started in February, I will block it now.  If you encounter problems with the installation and reading this thread, please try the above troubleshooting guides.  If this does not work, please start a new thread and include details about your system, all anti-virus/anti-malware products you use and ideally, your Setup logs.

  Thank you!

• Adobe Illustrator CS2 Doest not start! Tried everything...

  I have tried everything I can on my mac to the difficulty of this illustratorproblem. Illustrator freezes or stops loading or falls down or something at the start. I downloaded the mac.dmg file' of http://kb2.adobe.com/cps/534/cpsid_53468.html"but I don'thave the entire record, it described as the mappings, Unicode or anythingof sort." I also tried gel and reinstall the entire suite and then just the program illustrator. I've tried other solutions I found onlinesuch as policies removing or disabling fonts, adding the files I need, andnothing works. I also tried to create another user account, and it still does the same thing. I called and asked to Adobe and they refuse me becauseI have CS2 and not their new programs. So, I'm my own here, I am willingto try anything please help me

  I am running on a power mac g4 10.4.11.  I used the spotlight to find

  the location.  What are you running?

• Pavilion dx6500: Windows will not start

  I have laptop computer dx6500 computer laptop hp Pavilion Windows 7 Ultimate 64 bit running. I turn it on a day when he gave me a message that operating system is missing or damaged. Because I had valuable documents and other important stuffs on this subject, I decided to install a second operating system on the second partition and booted the laptop. I could get my fabrics that stood on the second partition and then I realized that the operating system has become two phone cuz always invite me to choose which operating system to boot from. Because I did not like that, I went to remove the operating system which was not established as the default operating system. The next day, I turn on the laptop to see a white screen with the message "press F1 to RESUME. or F10 Setup I pressed the F1 key and realized that it wasn't working, so I pressed the F10 key too but did not work too. So I decide to press any of the keyboard but realized that the keyboard did not. I decided to reformat then I inserted the windows installation CD in the drive so that he could boot from CD cos I put the CD drive as the first in the boot order but any time, I turned off the computer and turn it on, it goes back to same screen and would not even boot. Someone please help me!

  Hi @Dontworry,
  
  Thank you for visiting the HP Forums! A place where you can find solutions for your problems with the help of the community!
  
  I stumbled upon your post on the laptop and wanted to help you! I looked in your question about your HP Pavilion dv6500 CTO Entertainment Notebook and questions with press < F1 > to < F2 > for the installer to start. I recommend to restore the default BIOS settings. You could restore the BIOS withthis document by selecting the reload the default BIOS settings. In this way, it will look at the hardware installed on your laptop.

  If it's not a help to any first start Notepad hold b and Windows key. Just keep holding it. Once your nothing that happens, restart the laptop. This should restore the last configuration of the BIOS.
  
  Please let me know how it goes.
  
  Thank you.

• HP Pavilion dv5t-1000 will not start

  Hello

  Our battery died and now the computer initializes more. I did a hard reset, then unplugged, removed the battery, then hold the power button for 15 seconds, then plugged in and then tried to start.

  When we try to start, we get the HP screen and it says esc at startup. When we reached the esc, the computer is blocked.

  When we try to start and enter the EFI interface by pressing esc, it will beep with a solid 16 times pulsating rhythm. He says then esc... pause start-up, and then the computer is blocked.

  When we try to start and enter the EFI interface by pressing F10, the computer emits the same and then says the F10 bios menu, and then the computer is blocked.

  I fear that there may be a problem with the bios or other hardware failure. I would appreciate any advice.

  Thank you

  Paul

  Hi Paul,.

  Could you try removing the hard drive and you try to start?  Obviously it does not boot to the OS, but it can go beyond this splash screen.  If this is the case, try reinstalling the hard drive and see if it works now.

  If it freezes again without the installed hard drive, it may be a corrupted BIOS, and I see that you have tried to solve that with no luck.  I tried to click that link you, but he was dead.  You did to be sure it was the correct version of the BIOS?  If you have Vista or Windows 7, I think it would be the right version of the BIOS:

  http://h10025.www1.HP.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-75233-1&LC=en&DLC=en&cc=us&product=3744198&sw_lang=&OS=4062

  Of course you also could yourself some pain if this laptop is under warranty.  The guarantee can be verified here:

  http://www13.itrc.HP.com/service/ewarranty/warrantyResults.do?admit=109447627+1286541891570+28353475

  I hope this helps.

• MY TOP of DELL Dimension 1100/B110 DESKTOP will not start windows black screen of death.

  I had my computer when there was a power failure in a storm, it was on a surge protector but the next day I turned on the computer, it was clicking on and then he gave me a black screen with the time system and configuration system date drive and other different things, but no screen with safe MODE or something like that. and I have no enternet, here where I live. Help me please.

  MY DELL DESK TOP Dimension 1100/B110 STARTS at THE BEGINNING, GOES THROUGH THE MAIL. SO NOT ME NOT LEFT IN THE SAFE MODE SCREEN, IF I PRESS F8, IT GOES TO ANOTHER SCREEN WHICH ME SAYS THAT MY HARD DRIVE CANNOT BE FOUND. IF YOU GO TO ANYTHING ON THIS PAGE IT TELLS YOU THE "PRIMARY MASTER" PLAYER IS... HARD DRIVE. AND THE MAIN SLAVE DRIVE IS... OFFAND STUFF LIKE THAT BUT NO SAFE MODE OR ANYTHING. MY SCREEN IS A BLACK SCREEN. AND WHEN I START THE COMPUTER THERE AS A TRIGGER FOR A BIT BEFORE I GET THE SCREEN I GET. WHAT SHOULD I DO?

  Hello

  · You have the Windows XP Setup disk?

  You can follow the steps in the below links which will help you solve the problem.

  Link: "operating system not found" or "Missing operating system" error message when you start your Windows XP-based computer: http://support.microsoft.com/kb/321626

  Computer stops responding with a black screen when you start Windows XP: http://support.microsoft.com/kb/314503

  If you do not have the disk to the operating system, then you may need to contact the manufacturer of the computer. Link: http://support.dell.com/support/index.aspx?c=us&l=en&s=gen& ~ ck = mn

• Pavilion x 360: will not start

  HP Pavilion x 360
  Fully charged my camera before putting in operation and this is what has happened in stages:
  -prepare the auto repair
  -noise model
  -black screen (it is always on) nothing is popping up it just keeps making low noises
  It will display a blue screen with a sad face and a message to would pop a few seconds a word hard disk power something I forgot

  He has been in this State for a few months now and I bought almost a year ago.
  Once it was working, but it froze on me and happened the foregoing.
  He began to arrive when my classmates kept inserting their USB keys and get out them.

  If it's less than a year, it is probably still covered under the original HP warranty.  You need to contact HP customer care to see what HP can do for you: Contact HP customer care. HP® customer support