HP Pavilion does not start after upgrading Windows 10

Similar Questions

• FF does not start after upgrading to version 27.0.1

  FF does not start after upgrading to version 27.0.1
  Crash ID: bp-2bc18734-d643-4843-a10f-fd6102140214

  Firefox 27.0.1 is too recent for me to know what unique issues it may have. I will message you a link to download the installer for Firefox 27.0 to see that the inversion or not the problem.

• computer does not start after the Windows XP logo window

  Windows xp home edition
  service pack 2
  Dell inspiron 1501

  1. computer does not start after the Windows XP logo window
  2 works well in safe mode, even connect to the external monitor
  3. I reinstalled xp many times, problem stil exist.

  All the answers?

  Hi dhanushm,

  1. What happens after the Windows logo screen?
  2. You receive an error message?
  3. You have security software installed on the computer?
  4. Have you performed an installation clean Windows XP and even after that this problem exists?

  Method 1

  As the computer starts up fine in safe mode there is a possibility that some third-party programs installed on the computer is the origin of the problem.

  I suggest that you configure the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See section to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. Click Start , and then click run.
  2. Type msconfig , and then click OK.
     The System Configuration utility dialog box appears.
  3. Click the general tab, click Normal Startup - load all device drivers and services , and then click OK.
  4. When you are prompted, click restart to restart the computer.

  Method 2

  If fails it above step can refer to the article below and try the steps mentioned, check if it helps.

  After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

  http://support.Microsoft.com/kb/318027

• Re: Smoker L30-10 X PSL33E does not start after upgrading RAM

  Hello

  I have a problem with my laptop.
  It has 1024 MB of RAM (2 x 512), but it wasn't enough, so I decided to update to 2048 MB (2 x 1024).

  I bought two modules and my computer does not start after changing them.
  It was only a screen black (same BIOS has not started). I tried another combination of installation of memory modules RAM.
  2 x 1024 - did not work
  1 x 1024 - did not work
  1 x 1024 + 1 x 512 - working but not properly.

  BIOS find that I only 896 MB (1024-128 for the video card)
  I said OK. Let's see what will show windows. He was also 896 MB.
  I launched CPU - Z and it shows that the total size of memory is 1536 MB (medium detect both modules).
  I found that CPU - Z detect 1 module 1 024 MB and 512 MB secondary, but the BIOS detect only 1024 MB 1536. How is that possible?

  I have fought, is that my BIOS is old, then I update the toshiba Web site form most recent version, but the problem persists.
  Please someboy help me and tell what to do.

  PS. the Modules are new and work correctly.
  They have been tested.

  Hello

  Have you used two identical RAM modules?

  What kind of modules did you use?

  In my view, that the problem is related to the new, inserted modules.
  There must be something wrong with the modules or modules are not completely compatible if the laptop can not boot after installation.

  According to a few pages of the book handles the DDR2 533 MHz (PC2-4200) 200-PIN SODIMM modules.

  Did you use these modules?

• Satellite P200D-130 does not start after upgrading RAM

  Hi, I just upgraded the RAM on my P200D 130 but it does not start after that.
  I removed the 2 Hynix 1 GB PC2-5200 and put in 2 SO Kingston DDR2 2 GB PC667 (should be the same as PC2-5200).
  Post-market nothing happens, light power control is turned on, I him stays CD drive but screen black, no beeps.

  I put one of the 1 GB modules, it starts normally, then I tried a 1 GB into the lower slot module and a 2 GB module in the top slot and it works.
  I tried a single 2 GB module in each slot, even in the form of 2 2 GB modules.

  What could be the reason, better: what would be the solution to ensure that the modules of 2 x 2 GB to work?

  Thanks in advance,

  Michael

  Hello!

  I think that both modules are not compatible to the laptop.
  Normally you can upgrade your laptop to 4 GB. Look in the user manual.

  The RAM, you should bring the computer dealer and request a new one. More buy modules with the same specifications and dimensions. Try buying RAM with the same specs as before.

  Good bye

• HP Laserjet 2100 does not work after upgrade Windows 10

  HP Laserjet 2100 does not work after upgrade to Windows 10. Tried using PCL 5, PCL 6 and also tried the HP Universal print driver. I agree, this is an old printer, but I am disappointed told me "the printer is in error" when I try to print after this upgrade. Worked fine on Windows 7...

  Thank you!

  If the printer is connected using a parallel printer cable, please see the link below for the solution.

  http://h30434.www3.HP.com/T5/LaserJet-printing/possible-solution-to-LPT-port-issues-with-Windows-10-upgrade/TD-p/5372582

• Satellite A200 PSAEOE does not start after upgrading memory

  Hi, I am first time here.

  I bought a Toshiba A200 PSAE0E-03J02JDR with 2 GB of RAM. I bought a pair of ram Corsair (2 * 2 GB VS2GSDS667D2). The computer does not start after that I installed the memory. I have intel 945 chipset, which is capable of 4 GB (manual page 1-2). The bios version is 1.8 2007.

  Can anyone help me, please.

  Post edited by: Marian ovidiu

  Hello

  The A200 series supports different chipsets;
  Intel 945 PM
  Intel 945GM
  Intel 943GML

  As far as I know your laptop supports the * 943GML * Intel chipset and the chipset supports 2 GB RAM max.
  Take a look at your laptop s user manual * Page 18.*

  Summer: 4 GB of RAM are not possible, and therefore your laptop does not start.

• Venue 11 7140 pro micro HDMI does not work after upgrade windows 10

  Has anyone tried connect a HDMI microphone on their place of dell 11 7140 pro after windows 10 upgrade? Mine does not work after the upgrade, but the HDMI from the dock works.

  I have thus display driver problems on 10 to win.

  For me, the micro HDMI port works fine. I use an active adapter, so that could make a difference.

  The HDMI on the dock works well, but only if I directly connect to an HDMI display. If I try to use a passive DVI adapter, then the external screen is not recognized. In addition, the DisplayPort on the wharf is also unnecessary, regardless of the type of cable or attached monitor.

  I encounter this problem after performing a new installation of Win 10, using the brand Dell drivers and latest drivers Intel installed by Windows update.

  It is certainly a driver problem Win 10 because everything works fine if I boot the Tablet under Linux using a USB key.

• listener does not start after upgrading clusterware

  Hello. RHEL 5, updated the clusterware 10.2.0.5 RAC to version 11.2.0.4 grid (database version is always 10). After the reboot, a node is OK, but on another auditor does not start. If trying to run manually, it starts with the error "the listener supports no services". After comparing with another node, it seems that 'bad' node uses old file listener.ora, which is now 0 bytes (probably was allowed during the upgrade):
  
  $lsnrctl start
  LSNRCTL for Linux: Version 10.2.0.5.0 - Production on 12 March 2014 09:37:16
  From /u01/app/oracle/product/10.2.0/db_1/bin/tnslsnr: Please wait...
  ...
  System settings file is /u01/app/oracle/product/10.2.0/db_1/network/admin/listener.ora
  Log messages written to /u01/app/oracle/product/10.2.0/db_1/network/log/listener.log
  Listen on: (DESCRIPTION = (ADDRESS = (PROTOCOL = tcp) (HOST = rac - 2)(PORT=1521)))
  ...
  The listener supports no services ".

  where/u01/app... - is my home, the home grid is in / U02 oracle. On another node, listener starting grid House. I checked the Setup log and found no errors on the listener. What can I do to fix this?

  You need to check first, which is not running and why (. / crsctl res stat - you), a lot of resources are dependent on network net1. Start by watching clusterware alertlog and check the config network of the second node. If the basic config is very good, you can try with netca or command line (oifcfg, iflist,...).

• First HP: HP first does not start after upgrading firmware 20160414

  Hello world

  Yesterday, I tried to update the firmware of my first HP as the connectivity kit he advised. Now, the first does not start.  The only way I can get it to do something, is pressing the Symb key and reset at the back. It then enters the V16 recovery mode.

  I am able to download the firmware, but after that it just does not start.

  I have reinstalled the kit connection several times.

  I used the option "use the new method of update" in the connectivity kit. But it won't help. I tried to download older versions of firmware.

  I tried the factory reset options: A, F, key simmultaneously O and then with the reset on the back

  I tried the Apps, Esc, now.

  It just does not start.

  Any suggestions anyone?

  With sincere friendships.

  Sigurd

  Ziggy76 wrote:
  

  Hello world

  Yesterday, I tried to update the firmware of my first HP as the connectivity kit he advised. Now, the first does not start.  The only way I can get it to do something, is pressing the Symb key and reset at the back. It then enters the V16 recovery mode.

  ...................
  

  It just does not start.

  Any suggestions anyone?

  The suspect first IMO is win10. You are a brave man to make an update based on win10. Try to do this on a computer with 7 or 8.

  Some on this forum may say they made a correct update of the firmware with 10 victory.

  However, to win 10 is known to his problems with the drivers and the software which is not original ms or not correctly connected.

• Tecra A11 - 11N does not start after upgrading CPU

  Hello

  I would like to do an upgrade of the processor for my Tecra A11 i5 - 430 M 11N to a probably much faster i5 processor. I thought that the i5 - 580 M'd, but the laptop does not start when I installed this processor.

  I started the 430M, done some research on the internet and discovered that the 580 M has a very high FSB speed, and that is what probably does not work / not compatible with my machine.

  http://Ark.Intel.com/products/43537/
  http://Ark.Intel.com/products/49653
  http://Ark.Intel.com/products/49652

  and also http://ark.intel.com/

  Now, I went back to the computer store, returned the 580M and got an i5 - 560 M compared to its specifications as I've seen it would not compatible because it has the same speed of the FSB with the 430 M.

  I then later in the day tried to install this cpu as an upgrade, BUT alas!
  It STILL does not START ALSO.
  I was dumfounded left. The processors in the same line of the family are supposed to be compatible between them provided: lithography, FSB and socket type are similar.

  Or what I'm missing here?
  I did upgrades of CPU in many cases for desktop computers and laptops, and this is the first that has left me with no word to say!

  Please offer assistance or advice.

  Simon

  + The message has been modified.

  Hello

  Recommend to check this doc from Toshiba:

  + Can I put th CPU, screen, or motherboard in my Toshiba laptop? +
  http://APS2.toshiba-tro.de/KB0/FAQ35006D000RR01.htm

  Upgrading the CPU is not supported (officially).
  The point is that, even if the chipset would support the new processor, it would be possible that the laptop wouldn't start because of compatibility problems between the BIOS or other components on the motherboard and the new processor.

• Satellite L670-1EE does not start after upgrading RAM 4 GB to 8 GB

  I'm trying to upgrade the RAM from 4 GB to 8 GB. If I replace two 2 GB of 2 modules of 4 GB modules, the BIOS (which is the most recent) realize the 8 GB, but does not start at startup. There is just the white cursor blinking not.

  When I put in the 1 4 GB module and 1 2 GB module the system starts without a problem and has 6 GB. I checked the two 4 GB modules, they work in any combination, but not when both are installed together.

  I couldn't find any rider or the settings of the bios for the RAM...

  Any idea?

  Thanks in advance for the help

  The last plausible explanation is that both modules are ok, but not compatible with each other.
  The laptop can be upgraded up to 8 GB of RAM. This should not be a problem since the unit is supported by the Chipset Mobile Intel HM55 Express.

  So I think that you need to replace the modules Kingston modules are great and work without problem.

• Satellite 1410-304 does not start after upgrading memory

  I tried to extend the memory of 512 MB to 1 GB by placing two memory modules in my laptop Satellite 1410-304.
  These blocks of memory are each 512 MB and type: DDR400 PC3200 SODIMM.

  Each memory separate block in one of the memory slots A or B works well, no problems.

  However, when the two blocks of memory are installed, the laptop does not start no more.
  I hear the soft beeps indicating that a problem has occurred. The system works under Windows XP.

  Someone who can tell me how to solve this problem. Thanks in advance for your help

  concerning

  Marten

  Memory sticks are made by the same company? If this isn't the case, it will not work.

• Satellite L100 113 does not start after upgrading memory

  Hello.

  Our Integrator bring to our company KVR800D2S5, but laptop memory modules does not start :(

  I read manual - this laptop supports 533 PC4200 memory modules.

  But SO-DIMM 533 MHz will be delivered in one month...

  The memory modules, we can install to Toshiba L100-113?

  Thank you.

  Hello

  I think that the laptop does not power upward because of a barrette memory faulty or not fully compatible.

  Please visit this memory 3rd party:

  [Memory for Toshiba Satellite L100 113 | http://www.orcalogic.co.uk/asp/prodtype.asp?prodtype=22360&ft=m&st=3]

  As you can see Satellite L100 113 memory can be upgraded up to 2 GB (2 x 1 GB) and you must use the DDR2 533 MHz (PC2-4200) 200 - PIN SODIMM

  Concerning

• Compaq 6200 PRO MT: Makes the computer does not start after upgrade CPU

  I have the HP Compaq 6200 PRO PC of MT 615114-001 motherboard and processor Intel Celeron CPU (LGA 1155). After I changed the CPU for Intel Core i5 (LGA 1155) computer does not start. He begins a minute (less than one second) and stops again. No beeps. After you have installed the Celeron back everything works fine. i5 CPU is brand new. What can be?

  In my previous post, I explained the reason it has not worked, and listed the CPU that will work.

  HP tests CPU in the laboratory and publishes a list of processors that will work in a notebook.

  Notebook motherboard BIOS has a list of processors that will work. If it is installed, which is not encoded as OK in the BIOS ROM file, then this will not work.

  Processors published (in the maintenance guide & Service for your nttebook series model) are available in models that can be deilvered in State CTO (configured to order).