HP photosmart more B210 series - scanning and turning off problems

Similar Questions

• Satalite P300D: standby and turn off problem

  I have a problem with the sleep mode in particular. When I close the laptop, it is supposed to go into sleep mode, and sometimes he just did it, but other times (especially if I do two times after eachother) the fan turn on extremely hard and the screen goes black and the only way to stop this is to press the power button until the laptop turns off. Sometimes, I have the same problem with the laptop shutdown.

  I think it started right after the installation of windows 7, might have something to do with it?

  Hi mate

  Well, this could be possible since the Windows 7 supports a few different settings of energy management as well.
  I recommend the BIOS.
  You need to update it if a newer version is available.

  In addition, you must install Win 7 Vientiane (value package) which can be downloaded from the page of European driver for Toshiba

• Photosmart HP B210a more: HP Photosmart Plus B210 missing Scan software

  Hi all

  OK, Ive problems (two hacks, printer malfunctions, 1 disk repair, etc. over the past months) my Mac for the last two days, I restored Mac OSX 10.10.4 successfully and everything is well save for my printer as indicated above. I didn't know the usefulness was eliminated when I upgraded to Yosemite and it was hogging my CPU with a processing loop that was killing my Mac (I call her Alice!...)). So, I did get them all today my research on what went wrong with these processes which lead me to upgrade drivers Max OSX Yosemite and tried troubleshooting through:

  (a) installation of printers, their uninstall through the system preferences/printers and Scanners to verify that the drivers are there, I installed via the using field list driver HP Photosmart Plus B210, who can confirm print successfully without any trail of CPU (I uninstalled the HP before this point utility).

  (b) tried to get into the system preferences/printers and Scanners / where I chose "Scan" in the window of the printer and it says "SCAN SOFTWARE does IS NOT INSTALLED" (see attached printer screen)

  

  (c) I installed the driver in the development of window for HP Photosmart Plus b210 series that SHOULD allow the printer and scanner to work from my window System Preferences/printers and Scanners, I've lived more troubleshooting try to import a scan of the system of preferences/Applications/Image Capture and preview also. The two scan attempts to import sent the same message, lack of scan software when I tried via the printers & Scanner on System Preferences window.

  So frustrasting as she is, I set up a test on the printer to use the port MMC to scan an image of the window of the printer to the MMC card, that I inserted in the printer and it worked to prove that the software of the printer works on scan, but not directly with my Mac. Printing software is confirmed later, brings back me to my Mac and his missing scan software.

  This seems to be missing and appropriate drivers that should make the impression (works fine, no trail of CPU as before) as well as scanning (missing software problem). Does anyone know how I can fix this and if I need to download software drivers or anything please provide your console if necessary with links to what I need...

  Thank you all... I should have logged at noon instead of 4.30... I just might have gotten something else after you fix this problem...

  Try to update the software by following these steps:

  Click on the Apple icon, then select about this Mac.
  Click software update, and then click the Store from the top of the indicated window menu and click on reload the Page.

  Be sure to install any update HP or Apple, then check for the difference.

  If it persists, try manually install the package below. Tjen try to scan the image:
  http://support.Apple.com/kb/dl907

  If you're still having problems, try the HP Easy Scan application below:

  https://iTunes.Apple.com/us/app/HP-easy-scan/id967004861?MT=12

  Shlomi

• HP Photosmart Plus B210 Series does NOT print black

  I use Windows 7 to print to the printer HP Photosmart Plus B210 Series. The black cartridge has been listed as half full, but I installed a new black cartridge with no improvement. I selected the clean and align the print head, but the printer prints only the color inks and not black. I checked the vent of the cartridge on the black ink cartridge, and it is clear.

  Any suggestions?

  I have completed the troubleshooting steps and nothing fixed the problem. I even followed the instructions for soaking the printhead for 10 minutes in hot water. I guess that the printhead has gone bad and needs replaced. Thanks for your help.

• HP Photosmart more B210 not selected

  With my HP Photosmart more B210 printer, I accidentally not selected as the default printer.  I followed the video instructions to select this option to return, but he would not choose and instead, was a symbol of "troubleshooting."  There is no problems identified through troubleshooting.  I tried deslecting all other options down the left and always the symbol of "Troubleshooting" stayed.  When I tried to go to a frame earlier, the PH site says that there is no previous setting.

  At this point, I would say select you "remove device", then disconnect the USB cable.  Download the full driver recommended from HP here and reinstall the printer.  Do not reconnect the USB up to be instructed by the installer.

• Satellite P300 - 20 H refresh the screen every 10 minutes and turn off during 3 sec

  Hey,.

  Basically, I bought my P300 Sat about a month previously and each time it runs, battery, the same error will occur...
  It will update the screen every 10 minutes or more and turn off for 2-3 seconds.

  This isn't a big problem, but it is annoying that I can not sort.
  I tried to run a check of problem to find a solution, but he says that he can not find a.

  Help, please
  Thank you.

  Hello!

  Can you please explain what you mean with refresh? And what exactly is happening?

  It is not easy to say what the reason is for this, but have tested an external monitor on the laptop? And you can determine if it s a problem with the internal display or not.

  In addition, you must make sure that you have installed the latest display driver and BIOS. The two you can find on the Toshiba site:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported Downloads & => Download drivers

  If you installed a display driver Toshiba not you should remove it. These display drivers can often cause problems and don t have protection against overheating.

  Good bye

• Equium A60: After BIOS update device will beep several times and turns off

  Hello

  I downloaded the windows BIOS update for my Equium A60 (dated 11/15/05) and ran the executable by following the instructions, after ensuring that the current AC has been connected, etc.. The update has got a little more to halfway when the computer turns off suddenly.

  Now when I try to turn back on it just a few beeps and turns off again. It seems to me that the BIOS is screwed. Is there anything I can do to get my machine to run?

  Thank you
  Phil

  Hi Phil,

  Unfortunately, it seems that if the BIOS of your laptop is corrupted. Unfortunately, he didn't there has no easy way for you to correct yourself and you will need to take the phone to your nearest Toshiba Service agent who has the necessary specialized equipment to reflash your CMOS with a new BIOS chip.

  Kind regards

• Satellite A135-S4666 - cooling fan turns on and turns off every 20 seconds

  Hello

  I'm from the Argentina... I just bought a new Satellite A135-S4666 and I noticed that the cooling fan turns on and turns off every 20 seconds.
  It is a little annoying and it disctracts me of what I'm doing... is there a solution?

  Thank you very much.

  Hi Martin,

  This behavior is perfectly normal and nothing to worry about. If you find the noise irritating cooling fans you are likely to change their behavior by using the utility of Toshiba power where you should be able to set the cooling mode to run more quietly. I think trhe default is to allow the CPU to run at full speed, which will, of course, the fans turn every few seconds, but by reducing the speed of the CPU, the heat produced will be lower and therefore the fans will run less often.

  Kind regards

• Qosmio F20-154: BSOD and turns off

  Qosmio F20-154 goes to blue screen and turns off if the cd is inserted or if the flash drive is inserted
  Also hotkey error on turn on the computer

  Hello

  This means that you can not read data CD or USB key?
  Is this correct?

  Have you tried to boot from the CD or DVD?
  Have you tried to reinstall the OS?

• Satellite A60-181 heat up and turns off.

  Hope someone out there can help you.
  I was not able to use my A60-181 for awhile without being constantly plugged to electricity.
  And it seems to warm up and turns off.

  I bought a new battery, but I still get the same problem... and it is only 2 years old!
  Someone has an idea of what I need to do?

  In my view, this case is clear. It s a simple overheating. Usually the laptop stops automatically to prevent laptop damage material. Usually, this occurs if the laptop fans twist with speed and maximum performance.

  The reason for this behavior could be a dust and debris inside the laptop. Especially after 2 years of work and aspiration, the dust has a bad influence on the rotation of the fan.

  The module of cooling for computer laptop cleaning could help!
  But if you have no experience of it please contact the technician. It is recommended to clean the fans professionally.

• After the update to el Capitan my iMac will not be asleep. I put it to sleep and turn off the mouse and keyboard that goes with it, and 5-10 minutes later, he wakes up on his own. Now, I have to stop it after use and each time only. Major pain

  After the update to el Capitan my iMac will not be asleep. I put it to sleep and turn off the mouse and keyboard that goes with it, and 5-10 minutes later, he wakes up on his own. Now, I have to stop it after use and each time only. The Major pain. Any help would be greatly appreciated.

  Please test after taking each of the steps that you have already tried:

  Step 1

  Take all of the measures suggested in this support article, including those under the title "If the previous steps do not work." It is the starting point for a new effort to solve the problem.

  Note that, as stated in the article, the computer will not sleep, if some sharing services are enabled. In the menu bar, select

   ▹ System Preferences... ▹ Sharing

  Disable all sharing services.

  Step 2

  If sharing music iTunes home sharing is enabled, disable it or quit iTunes. Do the same with third-party applications that have a similar feature.

  Step 3

  Select

   ▹ System Preferences... ▹ Accessibility ▹ Speakable Items: Off

  Step 4

  Select

   ▹ System Preferences... ▹ ▹ Advanced Bluetooth...

  and uncheck the two boxes marked

  Open Bluetooth Setup Assistant at startup if...

  Step 5

  Reset the printing system.

  Step 6

  Back up all data.

  Triple-click on the line below on this page to select, then copy the text to the Clipboard by pressing Control-C key combination:

  /var/vm

  In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  A folder named 'vm' should open. Inside, there may be a file named 'drag '. Move this file and only this one in the trash, but do not yet empty. You will be asked for your password. Close the folder window.

  Restart the computer and empty the trash.

• Why windows constantly error reports and turn off

  Why windows constantly error reports and turn off. It is THE most reliable service.

  * original title - sucks of windows *.

  Hello williamiscome,

  This error message do you receive?

  The computer shuts down or restarts it?

  Let know us and we will continue to help you.

  Best regards

  Matthew_Ha

• After installing something from windows update my computer start Startup Repair each time and said "a hard disk problem is preventing Windows from start" and turn off.

  Hello

  After installing something from windows update (about 300 MB in size) my computer start Startup Repair each time and said "a hard disk problem is preventing Windows from start" and turns off.
  Then a window pops up saying "Startup Repair cannot repair this computer automatically.
  The details of the problem say;
  Problem event name: StartupRepairV2
  Signature of the problem 01: AutoFailover
  Signature of the problem 02: 6.0.6001.18000.6.0.6001.18000
  Signature of the 04:65537 problem
  Signature of the problem 05: unknown
  Signature of the 06 problem: BadDisk
  Signature of the 09 problem: unknown
  Signature of the 10:1168 problem

  System Restore does nothing, and all the other tools of recovery. :(

  Please help, it will be much apreciated :)
  DOM

  If you are sure that the problems began immediately after installing a Windows Update, use the free support of MS here:
  Visit the Microsoft Solution Center and antivirus security for resources and tools to keep your PC safe and healthy. If you have problems with the installation of the update itself, visit the Microsoft Update Support for resources and tools to keep your PC updated with the latest updates.  MS - MVP - Elephant Boy computers - don't panic!

• Is it possible to set up a computer to turn on and turn off itself every day or on any selected date?

  Is it possible to set up a computer to turn on and turn off itself every day or on any selected date?

  Mine is a HP G72-b27CL running Windows 7 64 bit laptop.

  Yes can schedule a task to start the system using the option shown in the screenshot below:

  

  You can schedule a task to turn the system off by as shown in the link below:

  http://www.thespinningdonut.com/how-to-automatically-shut-down-your-Windows-7-computer/

• Screensaver Windows 7 Pro x 64 and turn off monitor do not work

  On a new install of Windows 7 Pro x 64 (detail), the screen saver and turn off the monitor features do not work.

  I put the simpler (in white) screensaver at 1 minute and turn off the screen in 2 minutes, but are never triggered.

  I don't have a wireless mouse, as I read that may cause problems. All Windows updates have been applied.

  Please notify.

  Try to reinstall/update the chipset drivers and associated power, of your motherboard to the support site, maybe also an update of the Bios and