HP ProBook b 6450: issues of analog tapes to CD writing / Line-In

I have a HP Probook 6450 b, with 6 GB of RAM, running Windows 7 Professional (64 bit), equipped with the card its Intel(r) Audio display and the IDT Audio Control Panel, v. 1.0.6300.0.  I think I'm beyond the novice PC user and can even remove and swap the components of the laptop with success, although the will come I hope not at stake in connection with getting suggestions on the problem I have right now.

I'm trying to convert some audio analog tapes to digital format, for the eventual conversion for CD ROM media  I have a cassette player, which will provide the single channel output.  I also have a copy of Audacity, which I think is my best bet for capture and recording audio input.

I concede that I understand partially the role of the application of the IDT Audio Control Panel software installed, but I have noticed that it installs an Line-In option on the registration tab on the sound, under the Control Panel icon.  I tried to choose that and checked the Line-In input option under the configuration of Audacity.  I have 3.5 mm cable to connect the audio output of the tape drive to the input jack (MIC), on my laptop, but after several attempts, no audio output seems to be forwarded to the laptop and daring.  The microphone on the laptop works very well.  By plugging in an external speaker, I know that the cassette player's audio output.  My sound card doesn't have a dedicated Line-In plug, but I inferred that the IDT Control Panel has been able to fill this lack of a Line-In Jack with Microphone input jack.  And my cassette player, has only the single output (headphones) card available.

I have studied this subject of conversion band a lot, and I think my set-up is basically correct, but I think there is just a problem between the IDT Audio Control Panel and Audacity - software and my ability to record analog audio content successfully.  I will actively monitor this announcement for the next few days and provide comments/answers ready to any solutions/options/suggested questions.   Thank you!

Well, the answer to this question was not quite what I was hoping it would be, but there are a lot of questions out there, and perhaps a less number of responses (sort of a philosophical statement on life I guess...).

Anyway, here's some good news (I'm happier when I solve my own problems - although part of bread crumbs scattered along the digital track by some other bloggers, and some advice from right-to-target to a great Audacity manual online, were the key to the solution.)

Thus, it is a few steps (apparently) to get this band to Audacity output that are needed.  As for me (for later, when I forgot), that everyone, here are the steps:

  1. You must select the input parameters (Line-In) on Audacity
  2. You need to direct the sound output of the original device (tape player, etc.) to the Microphone Jack (not the headphone jack)
  3. On my HP laptop, you access the control panel IDT Audio and under the recording tab - set Microphone as the default recording device (it will probably have been set for initial internal Microphone as default device).
  4. You must ensure that your audio in the Control Panel icon, that tab Recording Microphone is set as the default device.
  5. The recommendation of Audacity tutorial, apparently, it is necessary in certain circumstances to track the Transport > Audio peripheral Rescan or restart Audacity instructions.
  6. From there, you will need to activate recording on Audacity and then adjust the audio output levels, on your output device original or on the audacity input slider.

And since the pictures are always better, here is the proof of the pudding... or in this case the sound.  I hope others down the road will find this solution useful.  I'm marking this resolved.

Tags: Notebooks

Similar Questions

  • Analog tapes in Garageband worm 4

    iMac 27 inch end 2013 10.11.2 running. GarageBand 4.1.2 worm (248,7) seems to be current answers here so here go us.

    Try to get a few old reel to reel audio tapes in garageband to scan content. Now my help Apple tells me that the headphone jack can be used for input or output audio sources. All I have to do is change in the sound preference. Well sound prefs gives me no option when I'm connected to the iMac with the audio bridge. Everything that comes is built into the microphone of the iMac. Power of the output line, which is the only tape recorder output. I use the cable is a male RCA plugs (they always call them who?) with a record mini heads.

    When I want to import analog tapes to a computer I always run it through an analog to digital converter as a BehrRinger UCA202.

  • I want to download DVDs, I made movies on analog tapes, my iMac for purposes of editing and archiving. None of the files are protected. How can I accomplish this?

    I created more than 75 DVD by copying the 30 years of personally owned and created the analog video tapes that have been recorded on my camcorder.  Now, I want to download these DVD on my MAC for editing and archiving of files application. I can't understand how better to achieve this?

    One of the possibilities-> http://www.roxio.com/enu/products/easy-vhs-to-dvd/mac/overview.html?rTrack=b_eas yvhsmac

  • Webcam HP Probook b 6450

    Hello

    I have a HP Probook 6450 b and it incorporates a webcam but when I tried to use it, he said that it was not on and I need to turn it on. How do you turn it on?

    Please help me.

    Kind regards

    Asim Ijaz

    Sorry, it's long back I answered,

    If the entry of imaging devices does not appear in Device Manager, go to the category of the "Bus USB controllers" in Device Manager, expand it, right-click on each entry "USB RootHub" below and click on uninstall. Once all USB roothubs are removed, click the Action tab and click Scan for hardware changes, check to see if the Webcam works, otherwise it may badly.

  • HP Probook b 6450-how can I get the recovery disc for the laptop. Crashed and don't have a recovery disk

    Got a Probook 6450 b that crashed. don't burn the recovery disk so need to recovery disks. tried to order online, but the site does not deliver in my country of origin.

    Have a friend who has a probook 6450 b but a processor 2.1 GHz and Windows 7 Home Premium OS. Mine is Wondows 7 Pro, 2.4 GHz. can I use its on my laptop recovery disks?

    How can I get preinstalled HP software back?

    Tell us about the hard drive crashed.  You can link it to your desktop and make a check disk on it? Which can make new bootable.  If you don't care the utility partition and recovery being installed (you really won't need if you download and make the disc), and then download it here (you might put in your key Microsoft 25-digit Windows 7 Pro code):

    http://en.community.Dell.com/support-forums/software-OS/w/microsoft_os/3316.2-1-Microsoft-Windows-7-official-ISO-download-links-Digital-River.aspx

  • HP Probook b 6450 memory upgrade question

    Hi all

    I seem to have a strange question seeks to upgrade the memory in a HP 6450 b probook (i5 - 480 m & ATI card). The laptop came with 2 GB of sps p/n 598856-002, which is ram 1333 mhz 1.5V with the manufacturer being ramaxel. I ordered and installed a few sticks of kingston 4 GB

    http://h30094.www3.HP.com/product/SKU/10473659/mfg_partno/KTH-X3BS/4G

    Mounted to them and all appeared to be as well as the operating system (win 7 32 bit pro) showed the recognized as 8 GB stick and 3 GB usable, the bios also reported 8 GB as well. However the moment that a 64 bit OS (Linux or Windows) is tempted to run just the laptop falls down or crashes

    I already tried this upgrade with two sticks of crucial memory but had exactly the same problem, so think about crucial memory was the question I put to the supplier and ordered the kingstons rather.

    I saw very similar question mentioned here:

    http://www.TomsHardware.co.UK/Forum/328016-30-memory-upgrade-ProBook

    and

    http://superuser.com/questions/580512/HP-ProBook-6450b-not-booting-after-memory-upgrade

    My instinct suggests this notebook can be very picky about the memory chips, it may have to be a 4 GB key 16 chip versus chip 8 4 GB sticks.

    Thoughts and help on this would be greatly appreciated.

    Thank you

    You are the very welcome.

    Yes, I have never, ever install any module of memory in my notebooks from HP that does not 16 chips.

    All the chips I use - 2 gigs and up, have 16 chips (8 on each side).

    Never had a problem.

  • Issues of analog input DAQ-6008, voltage not zero to pin when you are offline

    I use the 6008 NOR-DAQ to produce a series of tensions and then read a sense resistor using the analog input (CSR). I noticed that my analog input gives me 1.3 V, when I probe it (compared to the mass of the device), when it is completely disconnected. This changes the reading to give me a different measure of sense than expected resistance.

    Why is my pin for analog input non-zero? Any help would be appreciated. Thank you!

    The 1.3 V is expected. The USB-6008-and-6009 case have the strangest input of the world circuit. The input impedance is approximately 144000 ohms terminated in 1.4 V. check the document User Guide and specifications.

    Lynn

  • HP Probook b 6450: network card driver

    Newly bought laptop used with several problems - resembled a problem of software and the company is not interested.  Due to virus ussues, I just did a complete new installation of Windows 7 Home Premium (newly purchased).

    I am now unable to connect wireless to the internet and the message is "windows did not detect a network card is installed correctly.  I am also told "the drivers for this device are not installed Code 28'.

    I think that I committed a serious error in the installation of windows and should cut my financial losses by binning the laptop.  Any help would be appreciated - I am a relative novice with computers.

    Any advice would be greatly appreciated

    You are the very welcome.

    You need this card wireless driver...

    This package contains the Broadcom Wireless LAN driver and is required to activate the LAN adapter wireless Broadcom integrated in the laptop models running a supported operating system. This package also contains the Broadcom Wireless Utility and Extensions HSI application which adds support for the Extensions compatible Cisco.

    File name: sp63944.exe

  • HP ProBook b 6450: drivers


    Hello

    Download and install the Ricoh Media Card Reader Driver for PCI VEN_1180 & DEV_E230 & SUBSYS_146D103C & REV_01

    for the second of them should work

    http://h20000.www2.HP.com/bizsupport/TechSupport/S oftwareDescription.jsp? lang = in & cc = us & prodTypeId = 3...

    http://h20000.www2.HP.com/bizsupport/TechSupport/S oftwareDescription.jsp? lang = in & cc = us & prodTypeId = 3...

    http://h20000.www2.HP.com/bizsupport/TechSupport/S oftwareDescription.jsp? lang = in & cc = us & prodTypeId = 0...

    http://h20000.www2.HP.com/bizsupport/TechSupport/S oftwareDescription.jsp? lang = in & cc = us & prodTypeId = 3...

    http://h20000.www2.HP.com/bizsupport/TechSupport/S oftwareDescription.jsp? lang = in & cc = us & prodTypeId = 0...

  • HP ProBook b 6450: Solution Center Software for the range of all-in-one printers, HP Photosmart C4385

    I installed the package full HP printer and it has not installed the solution Center. Impossible to find. Need this to scan documents. What should I do?

    Hello

    You can download the complete software of this site features:

    http://support.HP.com/us-en/drivers/selfservice/HP-Photosmart-C4380-all-in-one-printer-series/3221640/model/3221645#Z7_3054ICK0K8UDA0AQC11TA930O2

    Once you have done this, is that you can uninstall before reinstalling the software downloaded?

    This printer model IS USED the Solution Center.

    Let us know how it goes.

    Please click the "accept as solution" if it helped to solve your problem and "Bravo Thumbs up" as an encouragement

  • Need drivers and software to download on my laptop Sony PCG-9RFL VHS analog tapes. Please notify.

    I have, as mentioned above, a laptop Sony PCG-9RFL.

    I have a RCA / USB cable to go from my VCR to my laptop, but none of the software on my computer recognizes the plugin.

    Help, please.

    B

    My apologies, Win XP Home Edition.

  • HP probook b 6450: Hp probook 6450 b no sound through hdmi cable

    Hello

    I have a problem, because I had a virus on my laptop, I had to reinstall windows 10. Everything is working again except when I plug in my hdmi cable it does not recognize the hdmi audio output. If I look at my audio devices it says: digital audio (HDMI) not connected. I tried to put my card video/audiodrivers/all drivers to day/re-installing what I think of cound, but nothing works. Prior to the re - install everything worked fine, so I think it's a software problem, I just don't know what it is. Can someone help me?

    Evan

    You are the very welcome.

    OK, you should be able to solve this problem quite easily.

    Because HP does not officially support your laptop for W10, but graphics driver W10 works, let's add the HDMI audio driver from the file of graphics driver for W7 on your laptop support page, without messing with the display of work W10 driver.

    First of all, download and install this free utility for files.  The 2nd high page file is 64-bit.

    http://www.7-zip.org/

    After installing 7 - Zip, download and save but are not run this file from W7 graphics driver.

    This package provides the graphics driver Intel high definition (HD) with Turbo Boost technology for the notebook models and operating systems.

    FTP://ftp.HP.com/pub/SoftPaq/sp64001-64500/sp64360.exe

    Now that you have downloaded and saved the graphic driver file, right-click on it and select 7 - Zip from the list of options.

    Have 7-Zip extract of: and leave it to extract the driver file in its file name of the file (sp64360).

    Once this is done, go to the Device Manager and click on the peripheral plain high-definition audio (not the IDT one).

    Click on the driver tab, click on set to update driver.

    Select her browse my computer for driver software option and navigate to the driver 7-Zip created folder.

    Make sure that the include subfolders is enabled, and must install the audio driver.

    Restart the PC, and you should now have the video and audio via the HDMI out port.

  • Missing drivers for HP ProBook b 6450

    I'm missing this driver

    • PCI VEN_1180 & DEV_E230 & SUBSYS_146D103C & REV_01\4 & 349FB80B & 0 & 01E2
    • PCI VEN_1180 & DEV_E852 & SUBSYS_146D103C & REV_01\4 & 349FB80B & 0 & 02E2
    • ACPI\HPQ0004\3 & B1BFB68 & 0
    • USB\VID_138A & PID_0007\0030F6AA5586

    Please can someone help me install the missing driver.

    Thank you

    Hello:

    Since you leave me guess what operating system you use, you will need to visit your laptop support and the driver page, select the operating system, you're running and download and install:

    For the ACPI\HPQ0004\3 & B1BFB68 & 0:

    HP 3D DriveGuard... Found in the storage section.

    For the USB\VID_138A & PID_0007\0030F6AA5586:

    Driver fingerprint sensor fingerprint validity... Found in the Security section.

  • And outputs analog table 2D through 4 lines (PCI 6711)

    Hello

    I want to design a user interface where the user can set the level of analog voltage of a specific analog channel for a certain period of time.  Basically, I need a 2D table where the columns represent each channel on the PCI 6711 map (Ao 0:3) and the lines represent a specific amount of time for each line to last.  I guess it would have to be another array of verical 1 d with integers representing the number of ticks that each line will last.  I can't seem to find an example of code where this is implemented, so some examples or suggestions would be grealty appreciated.  I have included a picture of another program that does this, and I would like to reproduce this configuration.

    Pass the array using a loop for. This example gets each line. You can then use the subset of the table to get the columns with the voltage. This gets wired to a game of writing DAQmx for n channels 1 sample. The duration column index and son to a delay. Try it and post back you're stuck.

    Sorry, but the answer above is meaningless to me.

  • I get more choice when I tap on the search line

    When I updated Firefox I get more choice when I type in the search line how can I solve this

    See also:

Maybe you are looking for