I need to run activex to connect to a server

Similar Questions

• Change the SSL connection on the Server VMware - what customers?

  Hello

  I currently have Mirage Horizon 4.2.3 installed and I use NO SSL. Server is available only for users within the local network.

  I would change it and this server on the internet for the users will be able to backup data during a move and I'll be able to get diapers for them.

  All guests of Mirage are pointing to the internal address of Mirage.

  My questions are:

  -If I change server settings will be I lost the connection to the LAN clients or I'll go 'extra' access via https?

  -is it possible to make clients to use SSL connection without re-installing the agent of Mirage?

  -I can do it without full re-synchronization of data?

  [Thanks for the replies and suggestions:]

  Once you have changed the configuration of SSL for a server of Mirage, customers also has need to use SSL for connects to the server, otherwise the connection will not be established.

  You can change the settings of the Mirage customer without reinstallation:

  -In Windows, the tray icon, open the status of Mirage, CTRL + ALT + S, a new window to set up the client must open and then check the Option 'use SSL Transport'

  OR

  -Edit the Wanova.Desktop.service.exe.config file and change the 'useSslTransport' for real 'touch' and then restart the service Wanova Mirage

  Full re-synchronization of data should not be necessary, as endpoint and always the same agent

• Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Im trying to fill the network so my ps2 connections can use the signal wireless to my laptop running vista Basic. When I click to bridge, I get a message saying that I need at least 2 internet connections. is this in any way about this?

  Hi Jer9009,

  Welcome to the Microsoft answers site.

  ·         Could you give the exact error code or error number you get?

  To connect multiple computers, install a network adapter in each and run a network CAT5 cabling to connect each one to a hub (and thus the other.) The computer that will serve as a transition will have a standard network card for wired and a wireless network adapter that will connect to the wireless (WAP) access point or gateway on the second network.

  A network bridge is software or hardware that connects two networks or more so that they can communicate. You can create only a single bridge network on a computer, but a bridge can handle any number of network connections.

  For more information, see the link: create a network bridge:http://windows.microsoft.com/en-US/windows-vista/Create-a-network-bridge

  Add a connection to a network bridge: http://windows.microsoft.com/en-us/windows-vista/Add-a-connection-to-a-network-bridge

  Swathi B - Microsoft technical support.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• need to run windows in safe mode with network to have browserws working properly. using IE and Firefox. Website of punch comes in properly next tab sites just wai

  need to run windows in safe mode with network to have browserws working properly. using IE and Firefox. Web site fisting comes in following correctly sites just waiting for the website tab help

  If it works in Windows safe mode, then you have a problem with other software, maybe a security software or a system driver that runs on your computer.

  It is possible that your security (firewall, antivirus) software blocks or limit Firefox or the process of plugin-container without you inform, possibly after the detection of changes (update) for the Firefox program.

  Delete all rules for Firefox and the plugin-container in the permissions list in the firewall and leave your firewall again ask permission to get full unlimited access to the internet for Firefox and the plugin-container and the update process.

  See:

  • https://support.Mozilla.org/KB/server+not+found
  • https://support.Mozilla.org/KB/firewalls
  • https://support.Mozilla.org/KB/fix-problems-connecting-websites-after-updating

• need a HDMI cable to connect to the macbook pro via port USB - C

  Could someone please indicate what cable or adapter I need to run my MacBook Pro to a TV movies? It connects on the port of lightning or another? Thank you Jude.

  No MacBook Pro has lightning ports or ports USB - C.  Most have ports Thunderbolt, and some have even regular HDMI ports.

  The adapter you need to depend on the exact model of MacBook Pro you have.

  Until we can tell you what cable or adapter you need, you must tell us what model of MacBook Pro you have.

  You can watch in the Apple Menu-> about this Mac, option and after the year of model here.

  How to identify MacBook Pro - Apple Support models

• I need to run wzc wizzard how can I do this?

  Wizzard

  I need to run wzc wizzard how can I do this?

  Hi Paul, try this...

  How to start the Automatic Setup Wizard in Windows XP, Vista and Windows 7

  Read Full steps detailed here: http://www.inf.aber.ac.uk/advisory/faq/965/

  Set up Windows Zero Configuration (WZC) XP

  Most wireless cards of Clients (computer/laptop) can be configured by a manufacturer Wireless Utility that comes with the card, or Windows Zero Configuration (WZC)

  It is important that the wireless should be handled only with a single application.

  You can use the original, or WZC utility. When a is used, the other must be Off (not loaded in memory and not maintained active Windows service).

  Disabling the Wireless Utility manufacturer must be explained in the document of wireless cards.

  The following describes how to check and turn the WZC. The same principle applies in case you should stop and choose the options Off / stop while you're in the menus (the same method can be used to configure other services too).

  1. click on Start and run
  2. type in the box run "services.msc" (without the quotes).
  3 scroll down and look for the Automatic Wireless Configuration service of

  Double-click the Service, screenshot of services

  4. make sure he started and startup type is set to Automatic.

  Screenshot of WZC

  If the Service does not start, or and is not set to Automatic.

  To start the Service, click the Start button.

  To set the service to automatic, click on the arrow down and change it to Automatic.

  No Configuration Service automatic Windows at all.

  Use Windows regedit, drill down.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\WZCSVC

  Add a DWORD entry that is named 'Start' and the value '2 '.

  Note that if you are not familiar with regedit do not use it without competent support.

  How to troubleshoot wireless network connections in Windows XP

  Source: http://www.ezlan.NET/WZC.html

• One or more ActiveX controls could not be displayed because that is: 1) your current security settings prohibit running ActiveX controls on this page, or 2) you blocked an editor of one of the controls

  Well this problem started a week ago. When computer first starts or restarts (I did not open any program still!) I get this message,

  One or more ActiveX controls could not be displayed because that is: 1) your current security settings prohibit running ActiveX controls on this page, or 2) you blocked an editor of one of the controls

  I know this usually occurs with internet explore, but as I said I do not have anything yet open. I've activated all the active X controls in internet explore with no luck. I searched the web for active x forums and blocked the editor and followed all the instructions in the error message (most of them see enabling active x) but without success. I am an advanced user (15 years and more), but it has left speechless me. If I try to open "Services", I get the same error. When I opened my anti virus, it opens but it is just a blank page. I know that my anti virus is working well.  Also if I open internet explorer, I get a blank page, if I go to a website (enter it or go to my favorites) it works fine. I've deleted all the temp, historical, cookies etc. etc. (use CC Cleaner and other programs to clean) but if reopened once again it says white. If I use help and you want to see a help topic that it is said (may not display due to problems of congestion or network, check connection) but internet works fine. I know that I have not a virus (a lot of people in the forums think it) I scanned with Bitdefender, Eset Nod32, Super Anti Spyware pro, Malaware Anti Malawarebytes, Spybot, Stopzilla, etc. etc. and did not find a virus (in safe mode) there are many people on the web with the same problem (with the same and some with different programs). This problem seems to be random (does not affect a certain program) I tried for a week now and I'm stumped! Anybody have ideas that I heard yet?

  Thank you if you do!

  Hi Morksr2d2,

  As you mentioned that the problem reappears as soon as you run the anti-virus program, it seems that we found the cause of these error messages at startup.  I would like to recommend that you Uninstall the antivirus & check if the problem reappears. This should also allow you to make changes on the services tab in system configuration utility.

  Later, reinstall the antivirus program.

  Hope the helps of information. Please post back and we do know.

  Concerning
  Joel S
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Need help solving any internet connection. This happened to me several months ago and the supplier

  Need help solving any internet connection. This just started today, but it's happened to me several months ago and at that time the provider thought it was software related and suggested that I have to contact HP. I have a HP 2006 m7674n, Windows XP. For several days, I worked with HardBeatZ on a different issue that has been resolved today. However, for several days, I had been working msconfig to track down the cause of the problem; This resulted in several reboots the computer - this would have something to do with it? Also, I just started getting a RUNAS box popping up. HardBeatZ has provided a link to a possible solution to this, but since I can't do internet connection I can't get the fix. Right now I'm on a laptop with Wi - Fi for the same service internet/modem as my PC. I changed nothing onmy PC in the last days of several for the internet connection or services.  I always use eithernet connection from the router to the computer. I tried Wi - Fi today with my PC but not connect. I tried to unplug the router and reconnect but it does not solve the problem. I did a Network Diagnostic and printed the report; Here are the warnings and error messages in this report:

  1. under the terms of the bridge diagnosis; Warning: "www.microsoft.comcould hostname not be resolved (0x2afc error code). Could be the gateway or DNS problem.

  2. under diagnosis of layer IP; Corrupted IP routing table. Default route, road closures, route host itinerary local subnet and local are all valid; Invalid entries in the ARP cache. ACTION: the ARP cache has been emptied. »

  3. UNDER HTTP, HTTPS, FTP Diagnostic; all three had this warning: ' 12007 connection error at www.microsoft.com: the server name or address cannot be resolved. " and the error was unable to establish a connection.

  Still under network adapter diagnosis; It shows the connection status of network as "connected."

  Also, I have an older computer that I connected with eithernet and was able to connect to the internet but has been disconnected because the version of Windows is too old to support the connection. But I could briefly connecting on HP website before you log out. The point being I think it's a computer problem and not an internet router or provider problem.

  I read a few entries on this site and it seemed that the recovery of the system was the only solution. I hope that there are other things to try before I resort to that.

  I would appreciate any advice on the steps to diagnose the problem and insight as to what may have caused this to happen. Thank you. dt2012

  Sorry... still with you... OK, we know that your network card is good and we know that your first post;

  1. under the terms of the bridge diagnosis; Warning: 'host www.microsoft.com name could not be resolved (0x2afc error code). Could be the gateway or DNS problem.

  2. under diagnosis of layer IP; Corrupted IP routing table. Default route, road closures, route host itinerary local subnet and local are all valid; Invalid entries in the ARP cache. ACTION: the ARP cache has been emptied. »

  3. UNDER HTTP, HTTPS, FTP Diagnostic; all three had this warning: "error 12007 connecting to www.microsoft.com: the server name or address cannot be resolved." and the error was unable to establish a connection.

  4. still under network adapter diagnosis; It shows the connection status of network as "connected."

  For me, it seems that Internet Explorer is corrupted or damaged. Your computer is shipped with Microsoft Windows XP Service Pack 2 Media Center Edition 2005 but since you can have updated to XP SP3 or upgraded to a newer version of Internet Explorer. Please try the options listed in this document to Microsoft titled "how to reinstall or repair Internet Explorer" , since there are several options depending on your system configuration, please post if you need help to solve your problem.

• Implementation of VPN for INCOMING connections to my server running Windows 7

  I need to set up a private network virtual SERVER on my server on Windows 7 and can't find the information I need to do this. Can someone explain what I need to do. I have a fixed IP address for my cable modem.

  I need to set up a private network virtual SERVER on my server on Windows 7 and can't find the information I need to do this. Can someone explain what I need to do. I have a fixed IP address for my cable modem.

  See this article for help...

  http://Windows.Microsoft.com/en-us/Windows7/set-up-an-incoming-VPN-or-dial-up-connection

  Remember that for a PPTP VPN server you must forward/open the TCP 1723 Port through a firewall or a router to the PC server is behind. You must also make sure that the firewall or the router will pass traffic GRE protocol 47 . This is sometimes called PPTP Pass Through or VPN Pass Through the firewall or the router. Windows Firewall automatically communicates the GRE protocol traffic if you make an Exception for the Port TCP 1723.

  You can test it by running the test detailed in sections PPTP Ping and VPN traffic in this Cable Guy article.

  http://TechNet.Microsoft.com/en-us/library/bb877965.aspx

  You can download the tools, pptpsrv.exe and pptpclnt.exe to Microsoft or if you have an XP SP2 CD. To extract the programs on a PC Windows 7 open the CD and select open folder to view files in the AutoPlay window.

  Extra help...

  http://Windows.Microsoft.com/en-us/Windows7/why-am-I-having-problems-with-my-VPN-connection

  MS - MVP Windows Desktop Experience, "when everything has failed, read the operating instructions.

• A Remote Desktop Client running Windows 7 can connect to a server running Windows server 2003?

  A Remote Desktop Client running Windows 7 can connect to a server running Windows server 2003?

  Want to know if I need to upgrade a Windows Server 2003, if remote clients are upgraded from XP to Windows 7.

  Yes, windows 7 RD client connect to Server 2003.  You will see just a security warning, but you can just click Yes and connect as usual.

• Need a graphics card to connect two monitors.

  Is AMD CrossfireX and Nvidia SLI is the only way to connect two VGA?

  Original title: graphics card...

  It is not no need SLI or XFire to connect two monitors. SLI and XFire are mainly to
  improve performance by connecting the two cards together.
  SLI, to have the same model of card when you use Nvidia IE - two GTX560ti, but apparently, you can use different templates with XFire as long as they use the same gpu (it's because they sometimes "re-brand" a gpu a series on a new map in the following series).

  You can connect two monitors to a card and run games on two monitors, but the seam in the
  Middle is a problem, so it is really best to go three monitors or a larger screen.
  You can also run a game on one monitor and have something to open on the other.
  This can also be done with two cards of different model that are not related (Nvidia or ATI).
  or your integrated graphics, if you and a single graphics card.
  You can also use both outputs of an integrated graphics card to perform the duties of Office Basic
  two monitors.

  To use a combination of graphics card integrated on my machine, I have to set the graphic option and dedicated North Bridge in the BIOS to "Onboard" or the integrated graphics card will not work.
  Also, when you use a single monitor I have to choose one or the other in the BIOS as only won't work
  at the same time when you use a single monitor.  It may be different on your system.

  There are different ways to use two monitors and the Setup is different between Nvidia and ATI.
  I've only played with Nvidia, ATI and Intel HD4000 options, so cannot really elaborate on
  the installation options.
  It is probably better to play with the settings of your cards some time control panel to
  get an idea of what is what and try again forum of the mfg graphics card for more details.

• I need to run two different versions of Firefox

  I'm currently crashing problems with Firefox 26 on openSUSE 13.1.
  25 Firefox works perfectly well. There's two versions of openSUSE rest. I suspect an add-on.
  To debug this I need to run both, one to report the bug and make my day job and one to test the bug.
  I saw the other similar thread, but I'm not sure that the subject is the same.
  I downloaded the last FF since the mozilla site and copied the folder ~ / Documents.
  But when I run "~/documents/firefox/firefox--non-reculees - p", choose a new profile, I always get firefox 25, the installed version, not Firefox 26, donwloaded version.

  If I add the troubleshooting information, the message is refused (too long)

  wait, it's me.

  I force you use local firefox correctly

  Sorry
  JDD

• Is anyone able to run Adobe CS5 with El Capitan now? I've read about problems with Illustrator and photoshop, but these seem to be in 2015 Octobe5. She improved at all? I need to upgrade that I am running an old OS v but I need to run CS5.

  I've read about problems with Illustrator and photoshop on EL Capitan, but these seem to be in October 2015. She improved at all? I need to upgrade that I am running an old OS v but I need to run CS5. Can not afford to go to CC. I have a Macbook Pro.

  CS5 and 10.11 are not supported and will never be supported by Adobe or Apple.

  However it works for some, more actually, but not all. There are sporadic problems with Illustrator, Photoshop seems to be the best. Do not expect an improvement and keep in mind that anyone from Adobe, Apple or anywhere else will fix it.

  Do a clean install

  Make sure you have the Apple Java

  h ttps://support.Apple.com/kb/DL1572?locale=en_US

  Make sure you have your serial number and if you are having problems with the serial number or the serialization however adobe of web server will not support your problem.

  update the application via photoshop.

• You want to know what ipad I need to run Apple Sound that for the scene.

  Sing Gospel music to the tracks on the CD.  You want to know which ipad should I get to run Apple Sound that to the scene.  That's all I'll use it for, so don't care about movies, phone, games, navigation, or much else. . She was told that 16 GB would be enough to hold 500 songs and IOS 7 need to run its what. If need one for this application. Don't know much to this topic, so really need help.

  Thanks Bill

  All the new iPad will run iOS 9 now. It would take a 16 GB iPad. I have 425 songs on my iPad, and they represent 1.8 GB of storage. But... You cannot add storage to an iPad, then you may want to consider eating less up to 32 GB. You never know what you could want on the road.

• Why do I need to run 7.1.1

  I was never very good at version control. Creating installation files is a pain if LV asks for such and such disc 2 years ago.  So, when I got my records of 2010, I did what I always do... I have uninstall the former LV (100%) and reinstall a new. In general, this works very well. I have to build my app again exe files, but it's OK.

  However, something is differenent this time.

  Everything seemed OK, but when I re-built a small exe and executed, the PC wanted to install Runtime 7.1.1. After the cancellation of the request, my program starts well. But now, same LV launch starts the request for RT 7.1.1 and I have to cancel.

  I tried to install RT 7.1.1 a DOWNLOAD but it fails because there is a more recent RT installed (and there has been for many years).

  Here is what I have done to contribute to this problem, I do not know how:

  (1) normally delete all software from LV is "grouped" in the Control Panel screen software, but I noticed an old runtime (6 something) listed separately, so I killed him.

  (2) I wanted to get rid of Datafinder (I hate the extra icons in my sandbox!) because I'm never going to use, so I uninstalled this software using the control panel.

  And that's all.

  Any suggestions?

  I think that the time required will depend on what you install in addition to LabVIEW. If you do not install the toolboxes or hardware drivers, it is possible/likely that you only need to run 2010. I have installed a generic LabVIEW since - never. I have time for 7.0, 7.1, 8.0.1, 8.2.1, 8.5.1, 2009, 2010 more CVI, GPIB, VISA etc, etc. Almost impossible (for me, anyway), what are the dependencies. Really nothing more it no more.