iCloud library do not turn off

Similar Questions

• Updates configuration: phase 2 of 3-100% full. Do not turn off your computer. Don't know what to do next!

  I have a 503WM Compaq Presario with Windows Vista Home Premium, which has problems after a Windows updated today.  First of all, I have installed .NET Framework (3.5?).  Windows Update started and downloaded a few other updates, and then asked to restart my computer - on restart received the updates configuration message, but when you have to configure the updates: phase 2 of 3-100% full.  Do not turn off your computer, nothing happens--or my hard drive internal or external are doing something and Ctrl-Alt-Del does nothing.  What should I do next?

  Before that, I installed Hallmark Card Studio 2010 Deluxe and received an error message 2738.  Followed the instructions on Microsoft to add two files that had to do with the VB script.  Hallmark installation instructions downloaded then installed .NET Framework 3.5.  The update of Windows has started and installed (I think) 4 critical updates.

  Hello

  I guess that part of the question could be a driver which is really old or similar should not be loaded.

  This exit Windows updates on (after you have access) and stop the updates of the driver to load.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ---------------------------------------------------

  You can use the solutions in this KB - 3 methods and I listed a little help for them below

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista
  http://support.Microsoft.com/kb/949358

  Method 1: Start Windows Vista with the Windows installation media and use the repair feature

  How to do a startup repair in Vista
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  You can also do a safe mode startup repair to access the Recovery Options If you have them available
  or use the DVD as described above.

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Method 2: Start the system in safe mode and then use the system restore feature

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can also do a restore of the system of starting with a Vista disk.

  Method 3: Use the downloads at the end of this article - note for Vista x 86 versions 32 bit and Vista
  x 64 64-bit.

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista
  http://support.Microsoft.com/kb/949358

  ------------------------------------------------------

  Once you are in Windows I was running once again reset here as a precaution.

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Hope this helps sort it out for you.
  Rob - bicycle - Mark Twain said it is good.

• My computer is stuck in "configuration updates: stage 3 of 3 0% complete.". Do not turn off your computer. It restarts just over and over again with the same message.

  I have a Dell Inspiron 1525 with Windows Vista, and I have tried the following to fix my endless reboot with the "Configuring updates: stage 3 of 3 0% complete.".  Do not turn off your computer. »

  • I inserted the cd 'Réinstallation DVD Windows Vista', but it won't pop up any kind of prompt for me to do something with it.  I tried putting the cd in what was on the computer and tried leaving him in and restart it - but the cd has no EFFECT.
  • I used the F8 key and I tried the following with no luck: safe mode, safe mode with network, safe mode w / command prompt, enable logging, last known good configuration (Advanced) boot and debug mode.  Most of these options make the monitor off (to make you think he will do something), then it just restarts and did the thing reboot loop again and again.
  • I also tried the repair your computer option to the F8 key.  He asks me to log in as an administrator (but my password does not work).  So, I use the menu drop down and choose the name of my computer and then use my password, and I can connect to "restoration of access options '.  Once I'm in the "System Recovery Options".  I tried the following with no luck: Startup Repair tool, restore the system, Windows complete PC Restore, Windows Memory Diagnostic tool and command prompt.  THE only ONE that I HAVE NOT YET TRIED it IS THE "DELL FACTORY IMAGE RESTORE", it's because I want to try to fix it without losing everything on my hard drive.  Here are the details of the I've tried in the "System Recovery Options".
  • The command prompt says: 32 X:\Windows\system > (I have no idea how to use it, but it's what he says)
  • The memory diagnostic tool reboots the computer, but nothing new happening (just reboot over and over again)
  • In the PC restore full Windows: I tried to put the Windows Vista CD in, but it can not find a valid backup location
  • When I click on the system restore: it is said: "no restore points were created on your computer's system disk.  To create a restore open system protection point.  When I click on the system protection, it is said: "your computer is running in a limited diagnostic State.  If you use the system restore in this limited State, you can't undo the restore operation.  Help topics are not available in this State. "  So I press OK, and I'm back to square one.
  • When I click on startup repair: it says "Startup Repair could not detect a problem.
  • I know there are many many posts on this problem, and I think I've tried all the suggestions on how to solve the problem, but they do not work for me.
  • PLEASE HELP ME!  I need my computer for my college work.  I can't borrow laptop my friend forever!

  Hello

  I guess that part of the question could be a driver which is really old or similar should not be loaded.

  This exit Windows updates on (after you have access) and stop the updates of the driver to load.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ---------------------------------------------------

  You can use the solutions in this KB - 3 methods and I listed a little help for them below

  The update is not installed successfully, you receive a message, and the computer restarts when you try to
  install an update in Windows Vista
  http://support.Microsoft.com/kb/949358

  Method 1: Start Windows Vista with the Windows installation media and use the repair feature

  How to do a startup repair in Vista
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  You can also do a safe mode startup repair to access the Recovery Options If you have them available
  or use the DVD as described above.

  This tells you how to access the System Recovery Options
  http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspx

  Try recovery options Startup Repair

  How to do a startup repair
  http://www.Vistax64.com/tutorials/91467-startup-repair.html

  Method 2: Start the system in safe mode and then use the system restore feature

  How to make a Vista system restore
  http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

  You can also do a restore of the system of starting with a Vista disk.

  Method 3: Rename the Pending.xml file, and then change the registry (this method is part of the advanced troubleshooting)

  See article below for that.

  You can use this method on the updates that have this problem.
  http://support.Microsoft.com/kb/949358

  Hide the update (click right - HIDE in the updates of Windows) and go to the Microsoft Download Center to download
  and install it.

  Microsoft Download Center
  http://www.Microsoft.com/downloads/en/default.aspx

  ------------------------------------------------------

  Once you are in Windows I was running once again reset here as a precaution.

  How to reset the Windows Update components?
  http://support.Microsoft.com/kb/971058

  Hope this helps sort it out for you.
  Rob - bicycle - Mark Twain said it is good.

• iPad IOS 10 - AutoCorrect keyboard does not turn off?

  I don't know if it is a problem of IOS 10 or if it is a question of the iPad. One of the first things I do when I get a new device is turn off easily. I hate to correct automatically, but it seems not turning off itself. I was typing a message to a friend of mine and to instead keep the word I typed (Pervy) it replaces (Percy).

  I just upgraded to IOS 10 and checked to see if the AutoCorrect has been disabled or if she has it on again. Even with typing this message, it keeps replacing words on me with words that I don't type and are not what they should be. It is not a question of spelling either, so I don't know what to do to fix, but it's very annoying.

  Hello. You may also need to disable predictive. If you are using a physical keyboard, there are different settings for it. They appear only when it is connected.

• MacBook will not turned off properly

  Hello

  my MacBook Pro 13 "2013 retina is not turned off properly after installing macOS Sierra.

  It takes about 20 minutes after clicking n closed. The screen is black and miss me closed animation (this circle loading bit). After a long time the circle appear and it takes 10-20 seconds (normal closing time) to shut down my computer.

  To me it seems that there is a program or task that can not shut down properly.

  How to see what program slowed down the process of closing?

  Thank you very much for your help!

  You can try a SafeBoot to clear the cache of the SafeBoot https://support.apple.com/kb/PH18760?locale=en_US files

  Try resetting the SMC http://support.apple.com/kb/ht3964

  Try resetting the NVRAM/PRAM http://support.apple.com/kb/ht1379 memory

  The recovery utility (R command at startup) try disc > first aid on your Macintosh hard drive

  You can always try reinstalling macOS 10.12 on top of your existing macOS 10.12

  Always good to have a current backup plan: make a clone of your boot disk bootable

• With this update my computer not turn off. Clears the screen, but this is all about.

  This computer is the new 12-inch mac that came out this spring.when I've updated about a month ago, it would not turn off. I got tired of hold down the b power button to turn it off. I returned it for a back earlier upward. It automatically updated again and here I am in the same disorder. I think I'll just close the lid and stop worrying in this regard.

  Stop your Mac. Use the power button if you wish. Now start with the SHIFT key is pressed. This will start in Safe Mode, with all extensions turned off. Safe mode is slow to start, so give it time, it checks a lot of staff. If it works fine in Safe Mode, restart normally. If it works now, you are finished.

  If the problem comes back after a reboot, you have an extension conflict. Disable all extensions via system preferences. To isolate which extension is at fault, turn on an extension at the same time, restart in the meantime, until you find bad.

• 9.3.4 iOS alert tone calendar do not turn off

  Since upgrading my iPhone 5 to 9.3.4, I can not turn off the sound alarm for a calendar event.

  I have a Gmail calendar sync on my phone and all my calendar notifications are set as follows:

  Show in Notification Center > WE

  Sounds > None (alert sounds and vibrations are set to None)

  The app icon badge > WE

  Display the lock screen > WE

  However, the reminder time for a calendar event, I get an alert of the lock screen AND a "rope" carillon. I also tried to disable all notifications of reminders, but nothing is done, there is simply no way to activate sound alerts in the calendar. It wasn't the behavior of calendar on 9.3.3. Am I missing something?

  Another thing, that I discovered after the upgrade is that the captions under the buttons on the call screen are now highlighted. Is it because of the upgrade or some other setting?

  Thanks in advance for all the help and advice.

  Hi John,.

  Thank you for using communities Support from Apple. I know have a problem with notifications, it is not what you expect. If I understand correctly, you get a sound notification schedule even if this setting is disabled. Looks like you have tried to adjust some parameters already, so here's what I suggest for this problem:

  1 first, turn off the Notifications options for the calendar, and then restart your device under the tap down and starting process is important to keep the iOS software works correctly. Select the appropriate Notifications options and test this new:

  Restart your iPhone, iPad or iPod touch

  2. If you still experience the same behavior, I suggest to backup your personal data and then reset all the settings in settings > general > reset your device. This resets all settings on your device such as Notifications, which will have to be installed again after testing your problem of Schedule again.

  The backup of your iPhone, iPad and iPod touch
  Import photos and videos from your iPhone, iPad or iPod touch
  Reset iPhone - iPhone help

  See you soon!

• NO IPAD SIM IS FROZEN NOT TURN OFF OR RESET

  Tried to put a day, has frozen will not turn off, reset or anything

  What iOS you're on at the moment?

• iPhone is blocked and is not turned off of either

  Hello. I was updating my iphone to the latest iOS version 9.3. Everything is going well, and then he started to check the update. A few seconds later, a message box appears saying that iOS 9.3 could not be updated because connectivity issues and the sign of updates to audit showed constantly on the screen. Because of that sign, I was unable to do anyhting on the phone, I asked Siri to turn off wifi because I thought that would help to make the sign to go away, but after having turned off the wifi, there was nothing I could do. Even the iphone is not turning off. Now the phone is locked and I am unable to do anything. Please help me with this and let me know what I would do as soon as possible. Thank you!

  Press the sleep/wake and home buttons and keep them for at least 10 seconds.

  If you are unable to activate your iPhone, iPad or iPod touch after installing iOS 9.3 - Apple Support

• Display does not turn off when attached to the ear during a call

  When you hold my iPhone 6 up to my ear during a call, the screen is not turn off and disable the buttons. The sensor is not broken, because the auto brightness works very well. It is just inside the calls when he won't work. Is there a setting to turn off the screen when you hold it to my ear?

  JBS - GUY says:

  When you hold my iPhone 6 up to my ear during a call, the screen is not turn off and disable the buttons. The sensor is not broken, because the auto brightness works very well. It is just inside the calls when he won't work. Is there a setting to turn off the screen when you hold it to my ear?

  The proximity sensor and ambient light sensor are two different things. The fact that your ambient light sensor works you says nothing about the functioning of your proximity sensor.

  You get a deal on the phone? A screen protector? If so, remove them and test again. If the screen does not always dark, you may have a hardware problem.

• Windows 8.1 message 'you could not complete updates, by undoing the changes, do not turn off your computer.

  Greetings,

  I installed updates in my Windows 8.1 partition.  Then he asked me to restart the computer, and the message "we could not finish updates, exchange loss, do not turn off your computer" appeared and was on-screen for hours.  I thought to reinstall bootcamp but I have software in the Windows partition that cannot be recovered.  I read that one of them starts Windows in 'Safe' Mode, but this is not possible. I use a MacBook Pro (retina, 13 inches, early 2015) OS X 10.10.5

  How can I fix this without wiping the Windows partition and lose my software?

  Thank you!

  Have you created a Windows system restore point before the upgrade?

• Default configuration of the Windows updates. Restoration of the changes. Do not turn off your computer

  Hi, I just refreshed my laptop that I got a few drops FPS at random. Initially, it worked fine, but after a while before instaled Norton started to cause me problems. At this time I uninstalled it and when he asked me to computer restatr now, I did. Now I'm stuck with this message window loading. Restart the computer from time to time, but the message is always the same: failure of configuration of Windows updates. Restoration of the changes. Do not turn off your computer.
  Computer: hp pavilion n006sm
  Operating system: win 8 pre-installed
  At the moment I'm stuck on this window for over an hour and nothing has changed

  Seems that problem solved by itself. As I correctly uninstalled Norton, I just put my automatic updates and restarted my laptop again. He installed the updates with no problem and its working fine. Seems that Norton was really the problem, will keep you informed.

• Satellite L750D - cooling fan will not turn off

  Satellite L750D-14R
  BIOS - 1.30
  THIS Version 1.10
  Temperature CPU Fan of 46% 53% speed

  Hi, just bought this laptop (5 days), the cooling fan is not turned off, the computer feels cool so don't know why it has run all the time. Read other articles on the upgrade of the BIOS but wouldn't go the upgrade in case missed me something obvious. It is a laptop replacement after the last Toshiba laptop (3 weeks old) no longer works in total. Prefer if possible to fix this with the help, rather than lose the computer for 3/4 weeks for repair, any advice would be greatly received.
  Thank you

  I put t know how you use your laptop computer but try to please use it with balanced power management. Change coolant also option method of optimized battery option. Cooling method you can find in the power options advanced > Toshiba Power saver settings.

  Please test and send feedback.

• Satellite PRO U300 does not turn off

  Hello

  I am facing a problem for the last few days on my Satellite PRO U - 300 (31st PSU)...

  The machine does not turn off and the power light stays on (blue LED) even after you have disabled. In fact, happened 3 - 4 times when I start the computer normally by pressing the power button / stop, it does not start and I noticed that the indicator was not extinguished even after + shut down +. Like any it is blocked! I have to finally, remove and reinsert the battery to start the laptop.

  Some details of my pc are as under:

  Version of the OS Microsoft® Windows Vista Business 6.0.6001 Service Pack 1
  BIOS Version V2.00
  Processor Intel (r) Core (TM) 2 Duo CPU T7100 @ 1.80 GHz

  Can someone help me solve this problem. Is it possible that during the uninstallation of programs, any perticular driver file is also deleted?
  Thank you

  JITENDRA

  Hello

  I don't know that you understand the indicator of power, but to me it sounds like AC Power LED and this LED is always on when the laptop is connected to the power supply.

  Power on / off LED is probably what you mean (the other starting on the left).
  Anyway, you turn off your laptop using a standard on the Start button?
  Are you sure you want to use the Hibernate mode.

  Believe me, the entire description here is pretty confusing to me. It may be that the laptop is turned OFF but power light is still on.

  Have you installed something 4 days ago? Or deleted some important application?
  Sorry, but it is not easy to say with certainty what the problem is here.

• Pavilion 15-e020tx: does not turn off pc portable hp pavilion 15-e020tx

  Hello.
  I have a pc hp laptop pavilion 15-e020tx. It does not turn off and does not wake up mode 'sleep'...

  I tried to restore my laptop to factory setting, updated everything I can, but it still does not work
  Could someone help me please

  Update the BIOS to the current version. A F.24. The direct link to the download is below.

  http://ftp.HP.com/pub/SoftPaq/sp69501-70000/sp69897.exe