If an entry is a constant range, is a tool that can make the exit choose for this number

Similar Questions

• That really means the vertical range? And the gain factor?

  The NI PXI-5102 digitizer: that means vertical range really means, it is the range of voltage of the signal to be measured or the signal to the ADC input terminal?

  How to control the gain of the digitizer? And what are the factors that can affect the gain?

  The portrait is located between the valid entries range of the digitizer on that channel.  If you set the interval to a value that is not valid, it will be converted to the next highest value.  This is the way you control the gain of the digitizer.  It is easier to define the vertical range on the maximum expected range of your input signal and allow the driver to NO-SCOPE compel the beach to the next highest value.  This allows you to use your code effectively with more than one type of digitizer (5102 and 5112).  For example, you know that your input signal has a range of 3 v (+/-1.5V).  Set the vertical range at 3.  OR-SCOPE that will force to 10V, the next beach valid more high for the 5102.  You can find the valid vertical beaches for your device in the folder of Documentation OR-SCOPE in your Start menu or online.

  Mitigation on your scope probe will affect the vertical range of the device.  If you have a 10 X probe and defined the vertical range to 10, the actual vertical scale will be 1.  You can have NO-SCOPE figure that out for you by setting the mitigation of the probe with vertical Configuration.

  More information on the routes of entry, and gains are available in NO-SCOPE help about using vertical configuration.

• Microsoft Bluetooth Notebook Mouse 5000 installation error: "problem installing the driver for the device software - file to install the driver for this device is missing a necessary entry.» Maybe it's because the file INF was written for windows 95 or la

  Original title: Microsoft Bluetooth Notebook Mouse 5000 install problem

  I have a LG S1 Pro Express dual computer with vista sp2. My Bluetooth Notebook mouse 5000 can be coupled to my computer, but after pairing, it will say "Device Bluetooth HID - ready to use" and "unidentified - device failed. It then opens a window saying "problem of installing the software driver for the device - driver for this device is missing a necessary entry.» Maybe it's because the file INF was written for windows 95 or later. »

  I checked some things here and read about intellipoint 7.x and installed but it still does not work. This used to work before mouse

  Hello
   
   
  The drivers that you try to install seems to be corrupted. Let us fisrt remove all traces of the software driver for this device in the Device Manager and then install the drivers from the manufacturer's Web site.
   
  Step 1.
  You can uninstall the audio drivers completely from the Device Manager and re-install from the manufacturer's Web site.
  I would also recommend to check if there are Windows updates for this device.
   
  Step 2.
  Here is the link to download the latest drivers.
  http://www.Microsoft.com/hardware/download/download.aspx?category=MK
   
  Select the type of product like "Mouse" and select the product as "Notebook Optical Mouse" and your version of operating system and the language of the operating system.
   
  This page will direct you to a link to download the IntelliPoint software, which is the software of the mouse.
   
  For more information see the links below.
  Automatically get recommended drivers and updates for your hardware
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly
  
  Tips for solving common driver problems
  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-fixing-common-driver-problems
   
  I hope this helps.
   

  Thank you, and in what concerns:
  Shekhar S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.

• Firefox has crashed, and now I have a constant stream of blank tabs that keep popping up in front of all the others. They will not erase.

  First all the tabs I had open suddenly lacking at the Firefox help page. Now I have a constant stream of blank tabs that keep popping up in front of others. I click again to remove the but they back just pop up. Also whenever I delete a tab while browsing a Web site, I get another white added to the front of all the others. I uninstalled and reinstalled the program and it did not help.

  You ensure that you do not have a problem with a sticky key F1 on your keyboard?

  Start Firefox in Firefox to solve the issues in Safe Mode to check if one of the Add-ons is the cause of the problem (switch to the DEFAULT theme: Tools > Modules > themes).

  • Makes no changes on the start safe mode window.

  See:

  • Troubleshoot extensions, themes, and issues of hardware acceleration to resolve common problems of Firefox
  • Solve problems with plugins like Flash or Java to solve the common problems of Firefox

  If this does not work in mode without failure, then disable all extensions and then try to find out who is the cause by allowing both the problem reappears.

  • Choose "Disable all add-ons" on issues to troubleshoot Firefox in Safe Mode to set window to disable all extensions.
  • Close and restart Firefox after each change through "file > exit ' (Mac: ' Firefox > leave";) Linux: "file > exit ')

  If this does not help then try a new profile.
  
  See basic troubleshooting: a new profile

  Your above posted the details of the system tampon() obsolete show with known risks to stability and security that you should update.

  1. Shockwave Flash 10.1 r53
  2. Next-generation Java plug-in 1.6.0_14 for Mozilla browsers

  Update the Flash plugin to the latest version.

  • http://www.Adobe.com/software/Flash/about/

  Update the Java plugin to the latest version.

  • http://www.Oracle.com/technetwork/Java/javase/downloads/index.html (Java platform: download JRE)

• X 220 tablet screen type indicates that (and touch the problem of entry / does not work)

  Hey everybody. I have a question since lenovo seems to lack a complaints when it comes to this. I bought a used X 220 and can not identify whether she should be multitouch or pen of entry only on models. Screen part number is (according to lenovo page):
  04W3462

  Model number is 42962WU

  Touch screen with your finger does not work (if any).
  I don't have a stylus (pen) currently since she was not provided with the laptop BUT:
  Said property windows: no pen or touch input is available for this view.
  Reinstalled windows freshly twice as well as drivers (once downloaded manually, twice used Lenovo system update)

  Says always the same and there is no tablet or pen and touch settings in Control Panel.

  In some other subjects, someone suggested a similar problem as solution installation wacom pen drivers, lenovo Digitizer drivers etc.
  Tried the drivers provided and with each driver throws the same error: a Tablet supported is not found on the system

  Maybe there detect pen close to the laptop and it should be good?

  A I just got scammed?

  Thanks a bunch!

  For all of you who have the same problem, it's a hardware problem (motherboard).

• In the example LabVIEW Full featured, which makes the entry point button reappear?

  My question is this: what piece of LV code or invoke the node for the TS engine makes the entry Point button reappear when loading a file of sequence?

  Background:

  I inherited a modified version of Full Featured LabVIEW UI, which has been moderately modified (enough so this restart is not really an option, but it is still quite similar to use as comparisons for behaviors).  In addition, this code was started in LV2012/TS2012 and I'm migrating to LV2013/TS2013, but this behavior is consistent in both versions.

  Here is what I tried:
  I have found that when the command connect runs (see attachment), the button which is a TSUI. IButton control, SEAO is grayed out or hidden.  In the unmodified example user interface provided with TestStand, button is again displayed when loading a file of sequence.  The problem is that when I load a movie file in my code and click it before the race, the button does not reappear. In my code, I can run the sequence successfully by right click on the movie file and selecting run, so I don't think the sequence has an error, or the process model.

  Thanks in advance,

  Seth

  Seth,

  The entry 'options' of the ConnectCommand function controls this. On help page for this entry, you can see that there are options for "ignore enable" and "ignore visible." Or any of them may affect the functionality of the key entry point. You could try to make the options for both keys 0 and see if that fixes the problem. If this isn't the case, please let us know.

• is that any limits the current entry for the digital I/o?

  Hi all

  I wonder if there is no limit on the input to the digital I/o port. I have a device about 0.2 volt voltage outputing and the manual says the maximum sink current is 25mA. I connect this signal to a DI entry in my 6711 map. I wonder if the current is too large for the entrance of DI or the PFI?

  As we have already mentioned, there is no current flowing on the device in low level mode.

  The current specifications mentioned see the maximum current that can be managed by the device in low level mode.

  I hope not to confuse you more than necessary. On a row of data to the TTL level, nothing flowing from the device to the main circuit in level mode high current. In low mode, there is flowing in the main circuit in the current device. This current is inherently limited by the circuit.

  So, if you have a file specification of 25mA max. of the peripheral device in low level mode, it will never sink too much power from the main circuit. You can connect two devices without any risk. The maximum current is just specified in case you manage more current with the device, a led or a relay for example. In this case, the charge current must be limited, so that you do not damage the device. But - as mentioned - this is NOT the case in your application.

• Search a directory of data and display the data that is within the range of dates

  Hello

  I have a full idrectory of data from overtime, and I think of search in the directory and display the data files for specific dates. I only started this encoding yet but I figure I'll take the brain of some SMEs here labview and start in the right direction. My goal is to go through a comprehensive directory of data taken for a month or MORE csv files and select the data to process and display office files the date of its registration. If I take the data of last week, last month or last minute, it should just treat as an exact or more.

  Please help me get started on the right foot

  End date will be probably greater than the start date, right? So, end date must connect at the entrance to the upper limit. Then wire in the range? to the conditional terminal of a tunnel of conditional indexation.

  Lynn

• I can change the settings on my netbook so that it is not "off automatically" I need a constant power when charging my flip camcorder

  Original title: changing the settings!

  I can change the settings on my netbook so that it is not "off automatically" I need a constant power when charging my flip camcorder

  Hello Christina MacInnes,

  Please visit the links below with respect to the power settings.  It's for Windows 7, so please let us know if you are using a different version.

  Power Managemnet

  http://Windows.Microsoft.com/en-us/Windows7/products/features/power-management

  Change, create, or delete a power plan (scheme)

  http://Windows.Microsoft.com/en-us/Windows7/change-create-or-delete-a-power-plan-scheme

• I can't have my Subvi simply use the default values for some of its entries?

  I use the code for a DS345 machine, using the sample code from here: http://sine.ni.com/apps/utf8/niid_web_display.download_page?p_id_guid=E3B19B3E9149659CE034080020E748...

  I use version 7.0 (because I'm in 7.1).

  Anyway. I managed to get the proper waveform I wanted, just stored waveform in the default values and frequency input, so I can some frequency I want input. When I run the example VI itself, it displays the waveform for the machine just that very well, however, when I use this example VI as a Subvi, it didn't come out of the machine data.

  Any ideas?

  Thank you

  Edit:

  When I say defaults for some of its entries, I mean the values that are usually connected by a user, controls that are not 'inputs' in VI.

  I understood the question, and I must say that I am embarrassed. If you look at the code, I'm feeding a resource VISA name, when the Subvi needs just a chain with the GPIB address number.

• OR USB-6009 can produce the constant current source/sink?

  Hi all

  I have a card NI USB DAQ to 6009. I need a battery for constant (charge/discharge current<1mA) and="" simultaneously="" monitor="" its="">

  I was wondering if I can use USB-6009 of output constant source/sink of charge/discharge current the battery? I've seen a few threads that says 6009 impossible to output constant son of currents, but other says we can use the digital output to provide the current, but it was not only described how.

  Thank you.

  All the outputs of the USB-6009 case are sources of tension and all have current limits low. There is no way to generate outputs current controlled directly from this device.

  What I would do (and have done) is to build circuits of external current source/sink with an op amp or a transistor and allows you to enable or disable a digital output of the USB-6009. If the current must be adjustable, use an op amp circuit that takes an input of the analog output of the USB-6009 voltage to set the current.  Use an analog input channel to monitor the battery voltage.

  Lynn

• How to perform several steps and the display of charts/indicators without repeating the same code for each entry (of the dozens of entries)?

  I have to repeat the same steps and display in the Panel before (graphic fft and other indicators).

  Do I need to repeat the same code for each entry/channel? I already have too many channels and whenever I change a measure (and code) for an input/channel, I have to repeat the changes to all the other entries.

  Thank you

  
  

• Make the double question mark average in a registry entry as------? \C:\WINDOWS\system32\drivers\

  In my registry HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\eabfiltr

  I see double points to mark that precedes the file name in the entrance to the path of the Image:

  Image path = ? ------C:\WINDOWS\system32\drivers\EABFiltr.sys

  They appear on a number of other drivers - I checked, some drivers with double question marks are signed, others are unsigned, which doesn't seem to be not that it.  The drivers are present and operational system.  Is there something special that means?  I couldn't find anything definitive in Google or Bing.

  That said, it does reference to a directory of temporary names created by windows at startup, does not sound like a sign of boredom

  http://help.WUGNET.com/Windows/registry-entry-path-preceded-ftopict630476.html

• You can change the default value of the page range when printing?

  When printing, the default value in the range 'page' is set to 'all '. Is it possible instead to set the default value of 'pages '?

  Hello

  In general, you have four options to choose the pages to print, including all pages in a document. To select individual pages or a sequence of pages, called a range, you can type the page numbers separated by commas or dashes. For example, if you type 1, 4, 5-7, only pages 1 and 4, and then pages 5 to 7, will be printed.

  The selection option prints only text or graphics that you have already selected in a document

  See: use your computer for printing, scanning and fax: http://windows.microsoft.com/en-US/windows-xp/help/setup/print-scan-fax

• Error in Windows Mail - "error 623 - system could not find the directory entry for this connection".

  Original title: Windows Vista, Windows Mail, error 623, unable to connect to the mail.
  This problem occurred after a storm. Modem was fried.  Replaced the modem with the modem "2wire" ATT.

  Now get "error 623: the system could not find the directory entry for this connection"or the sys works very well. " Att think maybe in Vista?  Help, please. Works of g-mail, but I like Windows mail.

  Hello Bbuddes,

  You can watch the following information/tutorial to help with most of the problems of Windows Mail.
  http://www.Vistax64.com/tutorials/62560-Windows-Mail-problems.html

  There is a section to reset Windows Mail which can help with your problem.

  Sincerely,.

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think