Image on the side of client caching issues

Similar Questions

• on the side of client vpn ip address Apple Server help

  Hello

  i've got server apple running on a mac mini running yosemite and I put it in place for the vpn and everything works well on the server-side and client-side. I have what may be a stupid question so patient with me. When I'm on my machine client and vpn is connected, in order to access the storage disk, I have running on my server I have to enter the static ip address, that I attributed to my server. call 192.168.0.14. My question is: what happens if my router on the client computer affects 192.168.0.14 on a device? This results in a conflict? can I assign a static ip address within a range of numbers greater than my server so it's less likely to happen? I'm worrying about something stupid? I'm doing something wrong? Thanks to a light that you can throw on this dilemma.

  George

  Your network server should not be in the same subnet as the network that you are from the connection.   Which means that subnets 192.168.0.0/24 and 192.168.1.0/24 - is the range 192.168.0.1 to 192.168.1.254 - should be avoided.   Better to use a subnet or block 172.16.0.0/12 one subnet in the 10.0.0.0/8 block.  Usually a 24 (255.255.255.0) subnet somewhere in the range of 172.16.0.1 to 172.31.255.254 or 10.0.0.1 to 10.255.255.254, respectively.

  If you are entering the IP address of your server, then the DNS server is either not properly configured the address IP of the DNS server is not communicated to the VPN client or there is something other odd here.

  If your 'router' - probably a gateway box IP offering a combination of IP, NAT router, firewall, port forwarding, and Server features DHCP - past through apparently, built-in DHCP server IP address then you want set up to prevent it to the addresses that you have assigned statically.   In other words, the DHCP server should not be configured with a pool of available IP addresses that include statically assigned IP addresses.

  If you prefer, you can have your OS X Server act as DHCP server and disable the DHCP service in the IP gateway.

  The features and configuration and management of the gateway box varies.

• Policies WSM Oracle server or on the side of Client or both?

  Introduction:

  I am trying to create simple web breaks of Jdeveloper 11.1.1.7. I created a simple class with a single method called sayHi() that simply return a welcome message.

  Web servers has been created and tested on this is simple example.

  Questions and discussion:

  Is there an option to configure or add police Oracle in BOTH client and server side. Why do we need to configure both client and server policies? Is it enough to set up the strategy in the side server only, so when any client attempts to call the method on the server, it must meet the requirements of the police in the server?

  What do we mean by the addition of police in the client side? I do not understand, that is to say that in the customer side no one can send the request unless the policy requirements is met by the auto sender? Is that what the police has something to do with the side Server?

  Political aside server are executed on the server side when a Web service request is received and before giving it to the service object Web corresponding. Policies client-side are executed on the client side after you create a new application and before submitting it to the server. In most cases it is not enough to set up a strategy to side server only. It is necessary to set up the strategy of 'customer' corresponding to the client side too, or the client, and the server would not release properly.

  For example, you apply a security policy to the side server that requires a user name token validation, you must configure the security policy corresponding client on the client side so that the Web service client to add the token of user name necessary for the SOAP message prior to submitting the request to the server-side. If you do not configure this client-side client-side strategy, then the Web service client will not add a username token to the SOAP request, and the server will not accept the request.

  Dimitar

• Touch zoom - jumps from image on the side?

  Hello

  
  

  When I try to zoom in on an image by pinching, the image jumps on the side while zooming.

  I tried the option preferred to focus on zoom-click.

  
  

  What can I do?
  

  
  

  -Lightroom CC
  

  -Yoga Thinkpad 14, win 8

  Could you please try to reset once in Lightroom preferences and try again.

  Location of the Preferences of Lightroom file: preference file and other file locations | Lightroom 5

• Is it possible to reduce a large image on the side Server (before serving the user)?

  One of the banes of my existence resizes the same image several times due to the it appears in a variety of contexts. For example, the main image in an article will appear larger it will be on the index page, where many teasers of the article are placed. There is the image that the Facebook "share" og. There... you get the idea.

  Same image, different contexts, a lot of resizing in Photoshop, a lot of files to follow... but I save on bandwidth.

  On the flip side, I can target the same image (large) and simply cut via traditional HTML (width/height) on the side of the browser, but which will result in the download of a file that is about 50-75% larger than what is actually needed. If the teaser of the first page displays a 1280px to 500px image, it's a huge (and potentially costly) waste of bandwidth.

  HOWEVER...

  If I could do the same SERVER side... in other words, tell the server to take only the pixels that he needs of the (large) image and serve only THOSE to the end user... so the same image could be used in every context, and only the necessary bandwidth is used.

  Is this feasible? If so, what is the process called officially, and where will begin to learn how do?

  Thank you!

  Sure. Just search the Web for ' php dynamic image resize "or change whichever way server, language of script you use.

• Adding images to the sides of the page width is fixed?

  Hey all -

  I was wondering how much it is difficult to add an image to both sides of a sheet of fixed width (960px). Something like the American Motorcyclist Association. Their images are clickable ads - I just want to add static images.

  I did a "view source" but does not know where one ends and another begins.  Add these images side would affect the reactivity of a site? Thank you.

  Of course that they are. But I had a bad thing-

  HTML {}

  background-image: url (.. / _img/bkg3.jpg);

  min-height: 100%! important;

  }

  {body

  Background: url (.. / _img/halfElephant3.jpg) not repeat fixed high on the right;

  margin: 0;

  do-family: Calibri, "Trebuchet MS", Arial, Helvetica, sans-serif;

  color: #771E00;

  min-height: 100%! important;

  }

  {#outer}

  Background: url (.. / _img/buffaloBG2.jpg) not repeat fixed left - 10px;

  }

  The two half images are on the body and that div. #outer The html code has this image of green background.

• How to capture the event of selection of a table on the side line client (JavaScript)

  The example is:
  < af:table >
  < af:column >
  < af:outputText... >
  < af:clientListener... / >
  < /... >
  < /... >
  
  However, the text does not fill to the top of the cell. So, if I click on the on the empty area, the event handler is not called.
  I hope, even if I click on the empty area of the line, the event handler will be called.
  In fact, if I click on a row of a table at any location, including the empty area, the line becomes blue. How to capture this select event row on the client side?

  You can try file the client listener as a child under tag instead of the ?

  
  ...
  
  
  
  

  The above code should call a function in your js file called "handleTableDoubleClick", which, in turn, queued a ClientEvent that can be attached to a Backing Bean method. Something like:

  ...
      public void handleTableDoubleClick(ClientEvent ce) {
         //do something when the table is double clicked.
      }
  ...
  

  hope that helps

• GUI of the side ThinPrint Client

  Does anyone know if there is a GUI available for ThinPrint Client side of the view?

  At the present time when installs the Client view, settings, it installs the ThinPrint are by default.  There are 2 important keys that are installed as part of this process that someone please pointed out recently on this forum.  They are:

  HKLM\Software\ThinPrint\Client\DefaultState - the default value is set to 1, which will ensure that your default printer on your virtual office is the same as the default printer on your local desktop.  Setting to 0 allows to change your default printer on the virtual desktop and keep this setting.

  HKLM\Software\ThinPrint\Client\DefPrintState - the default value is set to 1, which will ensure your local desktop (connected local or network) printers are mapped via ThinPrint in your VDI session.  Assignment of 0 interrupts ThinPrint mapping of these printers.

  These two parameters are very useful as the default settings may cause problems depending on the use case.

  Unfortunately, since these settings are in HKLM, a user requires admin rights to change.  Otherwise the customer view could be expelled with a transformations to change the default settings.  These two options are impracticle as a user may want to edit them on the fly.

  So the question is how is this possible?  Is there a. Available CPL or some available GUI that would solve this problem?

  Thank you

  From my understanding, you can go the ways local and AD Group Policy. Check out this document:

  www.vmware.com/files/pdf/VMware-View-ThinPrintGPOConfig-IG-EN.pdf

  VMware View-ThinPrint; Basics

• Cannot move the image to the side

  I have this page

  http://charlesnewmanpubl.com/catalog.html

  When you click on one of the track list, an iframe with a player rises, and a little on the image to download the file. But this is supposed to appear next to the drive, and instead, he keeps appearing directly below.

  Here is the code

  <iframe style=" display: none; width:400px; height:27px; border: 0;" id="mp3Holder" src=""></iframe><a href="" id="ac3dl" style="display:none;"><img src="http://charlesnewmanpubl.com/images/dl_button.jpg" width="30" height="19" border="0" alt="download"></a>
  

  How can I get it to appear to the right of the drive?

  
  Download Source File
  
  Take out what is highlighted in red and that should do the trick
  

• Several images in the header...

  First of all, I'm pretty new to Dreamweaver and work with HTML/CSS so newb friendly instructions and suggestions would be appreciated:

  I'm trying to add three images in the header of a liquid template 1 column. A small image to the side left which is a logo, a picture of the environment which is a standard banner/header and a picture on the right, which is a little graphic. However, if I try inserting several images in the header area - the second image automatically will come down to a new line under the first and so on.

  I want all of them to deal with the header in line with each other.

  Thus, I would like the left graph (a logo) to align the left edge, the image of the middle to stay centered and the right image to align right automatically - so that all of the header appears (somewhat) to expand or shrink with the column of the main body. I know enough to make a single image in the header auto-align where/how I want and how to put in place a custom CSS rule... can't do all three images appear online next to each other.

  I tried to insert a table of 3 rank (no columns) in the header, then insert the images that way, but the table does not grow/shrink for the purpose. However, I'm sure there's probably a better solution anyway.

  Thanks for the help in advance.

  apilgrim101 wrote:

  But I could not reproduce the same results from scratch with DreamWeaver for some reason any: first two images work fine, but if I set the new CSS class for the right one, it falls on a new line.

  Show us the new code you are editing.

  Answers to the questions of layout are still in the code.

• UCM images in the browser caching.

  I use presenter content to show images of the Complutense University of MADRID. Appeared fine, but every time that I load image page url points to the server of the University Complutense of MADRID as http://< UCMserver >/cs/idcplg?...

  My question is why these images are not being cached by the browser. Why my browser is trying to get these images still on the server.

  I have other images in my project, which come directly from my code. These images resemble URLs http://< appserver > / < frame > /images/image.png etc

  These images are getting cached in the browser.

  What should I do for images UCM cache also the side browser?

  Thank you

  Sanjeev.

  If you consider your question, it is actually a WebCenter Portal question since he is presenter of content that performs caching, regardless of the source.

  Take a look at this white paper on Oracle Web Cache - http://www.oracle.com/technetwork/middleware/webcenter/webcenter-webcache-integration-176984.pdf

  Note that Oracle Web Cache is a feature of the Web of Oracle, the Oracle web server layer, so if you have an architecture where the web servers are different application servers (Web tier is also included in licenses of Weblogic Server), you will need a special permit for this.

• I - Phone video sent to me to my grandchildern, are on the side. I would like to 'spin' as I am able to do with images

  I - Phone video sent to me to my grandchildern, are on the side. I want to 'spin' as I am able to do with images. I can't find any opportunity to 'change' on the videos. Does anyone have a solution? Thank you

  Hi SandyTurkington,

  ·         What version of Windows is installed on your computer?

  ·         What application you're using to play the video file?

  ·         What is the file format of the video file?

  You have this option to rotate a video in Windows Live Movie Maker. If you have not installed Windows Live Movie Maker, you can follow the link below and install Movie Maker:

  http://windowslive.com/desktop/MovieMaker

  Once you download and install Windows Live Movie Maker, you can follow the steps below to rotate and save the video:

  You can turn video clips in Windows Movie Maker by following these steps:

  a. import the video clip in Windows Movie Maker.

  b. drag the imported video clip and drop it on the timeline.

  c. on the Tools menu, click Video Effects.

  d. to rotate the clip to the right, drag the effect video rotation 90 and drop it on the movie in the timeline.

  -or-

  To rotate the video clip on the left, drag the video effect rotate 270 and drop it on the movie in the timeline.

  e. on the file menu, click on the video file and follow the instructions of the wizard movie recording.

  Hope this information helps.

• Image of the Webcam on the side

  I have a new T420 with integrated webcam.

  My problem is that my webcam image is always on the side. For example, this happens when I press Fn + F6 to bring up Lenovo's Communications Utility, which displays the image of the webcam and allows me to control its settings.

  The 'advanced settings camera' that Lenovo provides in their Communications Utility allows me 'Flip' or 'Mirror' image that I see, but does not give me the possibility of rotation of 90 degrees, which is what I should do to fix the problem on the side.

  Can someone tell me if there is anything I can do to work around this problem, or if on the contrary, it is a problem of driver/software of a certain type, or rather so, maybe that the camera has been installed physically hurt in my T420?

  Kevin

  I think that the camera has been installed on the camera/mic PCB incorrectly, you will need to have serviced it.

• Is it possible to increase the width of the panels on the left and right if the sides during the import of images?

  Is it possible to increase the width of the panels on the left and right if the sides during the import of images?

  Lol the side panels in the import window are of fixed size.

• I JUST DOWNLOADED AND INSTALLED ADOBE PHOTOSHOP ELEMENTS 13. WHEN I OPEN IT AND PUT AN IMAGE TO CHANGE. THERE ARE ONLY 8 TOOLS SHOWING ON THE SIDE LEFT. THERE IS NO TOOL ERRACER OR OTHERS. WHAT SHOULD I DO TO SOLVE THIS PROBLEM. «"«DINO»»»

  I JUST DOWNLOADED AND INSTALLED ADOBE PHOTOSHOP ELEMENTS 13. WHEN I OPENED IT AND PUT IN AN IMAGE TO CHANGE. THERE ARE ONLY 8 TOOLS SHOWING ON THE SIDE LEFT. THERE IS NO TOOL GUM OR OTHERS. WHAT SHOULD I DO TO SOLVE THIS PROBLEM. «"«DINO»»»

  Hello

  You are probably using the Quick - switch to Expert mode at the top. All the tools are only available in Expert mode.

  Brian