IPS (AIP - SSM) ASA5520 module

Similar Questions

• CSM up-to-date IPS AIP - SSM

  Hi all

  I need help. I'm setting up my 3.1 CSM to apply the update on my IPS AIP - SSM.

  I went to the FPS tab apply and choose Update cisco.com. But it's still as treatment for a long time.

  I tried to enter my username and password for the sensors or account of the BCC but still no improvement. Anyone know how to configure it. I tried to read the user guide there is no examples.

  Thank you

  The two IPS - K9 - 5.1 - 8.pkg abd IPS-SSM_10-K9-sys-1.1-a-5.1-8-E3.img will recreate the image on the partition recovery and the application partition.

  The System Image will erase everything before starting the imaging process.

  The Service Pack Upgrade file will first of all take the current configuration and convert it to work with the new version and save off the coast. Also several other special folders on the sensor (for example, the license file) will be saved off the coast. The imaging process will run and then the saved to the large files will be automatically applied to the probe.

• where connect AIP - SSM 10 MODULE INTERFACE

  Hello

  We have CISCO ASA 5520 model with Module AIP - SSM 10 IPS, I'm new to IPS,

  1. I do not know where to connect from this port module (connectivity) another port it should connect to any router interface or L3?

  2. which IP address to use, it should be accessible network IP or customer?

  3 and the functioning of the IPS. ?

  with kindness is - anyone can guide me.

  Hello

  You will need the credentials of EAC by means of which you should be able to connect to www.cisco.com

  SPSP

• ASA5510 and AIP-SSM-10 module in promiscuous mode

  Hello

  I have a 5510 ASA with the AIP-SSM-10 and want to use just like an ID in promicuous mode.

  ASA 5510: ASA version 7.0 (8)

  AIP-SSM-10: IPS version 5,0000 E2

  At this point, we would like to configure a single interface of ASA to send traffic to the agreement in principle for the inspection of IDS (and continue to use our firewalls third existing). Is this possible?

  The following discussion gives to think this isn't:

  https://supportforums.Cisco.com/message/957351

  22.1.100.2/28 I have it configured on the interface Eth0/0 (outside) and 10.5.100.3/24 on the AIP - SSM management interface and switchports (Cisco 6509) have been configured by SPAN.

  Thanks for your advice in advance.

  Kind regards

  Lay

  You are right. Unfortunately, module AIP on ASA firewall does not listen on traffic SPAN. If you want that SPAN ports, then you can use the IPS (IPS 4200 series appliance) appliance that supports the SPAN traffic to inspect.

  PIX is also a firewall, not a feature of IPS, which cannot be used as an IPS device.

• Block P2P software using the ASA-AIP-SSM-20 module

  Hello

  I have a question about blocking P2P traffic on ASA AIP module. I've searched the forums and all I could find were solutions using regex, port block, MPF, but no example of implementation of AIP.

  Could someone point me in the right direction please?

  Thank you very much

  Martin

  Hello

  You can find all the associated p2p signatures in:

  http://Tools.Cisco.com/Security/Center/home.x

  A search using Signatures, p2p, all. Then, you can set the respective signatures to your needs.

  SPSP

• How to change him manage, lying on AIP - SSM ASA5520 IP

  As the title says how can you cahne the IP address of management? I was told, we could change but now we cannot access the device after reload to reset the password.

  current IP is not valid.

  IPS worm 6.0.3

  ASA worm. 7.2.3

  You must use a comma instead of a space between the subnet mask and the default gateway.

  "10.1.1.13/24,10.1.1.1" instead of "10.1.1.13/24 10.1.1.1".

• Cisco ASA 5510 + license + AIP - SSM

  Hello.

  I have this box.

  I have a few questions about it.

  (1) I'll be able to update the firmware (from 8.2 to 8.3 or greater for example) without smarnet for ASA 5510? And what can not do without smartnet?

  (2) I have only AIP-SSM-10 module this ASA 5510. is there a smartnet, too? And when I buy only one module is it build in a subscription for 1 year for the signatures of the IPS?

  (3) if I have the Cisco ASA 5510 base license, my IPS on AIP-SSM-10 will work?

  (4) as I foresee in a purchase of the year a 5510 more with the same module and mount ther of failover. I really need license Security more than failover (active / standby)? For active/active, I know I need one, Yes?

  Please help me.

  (1) you must Smartnet in order to download the software from the download from cisco.com site.

  (2) Yes, there is also a smartnet for the AIP module. Module AIP does not come with one year subscription, but you can ask for a demo license.

  (3) Yes, the basic license is OK for the AIP module.

  (4) Yes, you would need license security more on the two ASA to be able to run any type of failover on ASA5510.

  Hope that answers your questions.

• Getting started: ASA5520 w / AIP - SSM

  I'm trying to deploy an ASA5520 to a customer. I have no problem with the piece of implementing firewall, but I don't know where to start with the piece of IPS.

  I searched a bit on the ASA55XX & AIP - SSM, but can't seem to find much on what to do with the AIP - SSM beyond the initial Setup.

  Can someone point me to some beginners IPS documentation that focuses on the AIP - SSM?

  Thank you

  Jeff

  In my view, there is a lack of documentation on how to get the IPS module to work with the ASA. It would be nice if there was a single document on how to get IPS working module with the ASA.

  Start with the documentation of the IPS. It's just on how to configure the IPS himself module. Assign an IP address for management, set the admin password, etc..

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids12/index.htm

  Then go to the documentation of the SAA on how to configure ASA to send traffic to IP addresses (via a service-policy):

  http://www.Cisco.com/univercd/CC/TD/doc/product/iaabu/csids/csids11/cliguide/clissm.htm#wp1033926

  There is a free viewer of IPS Cisco event offering to monitor events on the IPS. It can be downloaded from the download page of the Cisco IPS software.

  Finally, read the whitepaper SAFE on the deployment of the IPS and the setting.

  http://www.Cisco.com/en/us/NetSol/ns340/ns394/ns171/ns128/networking_solutions_white_paper09186a00801bc111.shtml

  I hope this helps. Remember messages useful rate. Thank you!

• Module AIP - SSM hung

  Hello

  I recently confgured my module AIP-SSM-40 in my firewall that is configured in HA(Active/Standby). It was working fine. Then, I upgraded the version of the image to IPS, 2.0000 E3.

  It worked fine for a week. Then I found that the secondary firewall was in a State of secondary failure. My AIP - SSM in the secondary firewall fails.

  I couldn't connect the AIP - SSM with command session 1. Display the order watch module

  Model serial number of map mod
  --- -------------------------------------------- ------------------ -----------
  0 ASA 5520 Adaptive Security Appliance, ASA5520

  1. ASA 5500 Series Security Services Module-40 ASA-SSM-40

  MAC mod Fw Sw Version Version Version Hw address range
  --- --------------------------------- ------------ ------------ ---------------
  0 0021.a09a.d1bb for 0021.a09a.d1bf 2.0 1.0 (11) 5 8.0 (4)
  1 0023.5e15.f6c8 to 0023.5e15.f6c8 1.0 1.0 (14) 5

  The Application name of the SSM status Version of the Application of SSM mod
  --- ------------------------------ ---------------- --------------------------

  Data on the State of mod aircraft compatibility status
  --- ------------------ --------------------- -------------
  0 to Sys does not apply
  1 does not not Applicable

  at the end of the failover see command shows

  Slot 1: ASA-SSM-40 rev hw/sw (1.0 /) status (does not/high)

  I suspect module SSM is having the problem. Is it possible to recover.

  Try to stop and reset the module using this command from the ASA:

  HW-module module 1 reset

• The ACE IPS Cisco and Cisco ASA AIP - SSM (IPS)

  Is there a difference between the features offered by the Cisco ACE IPS and Cisco ASA AIP - SSM (IPS) devices?

  Can we do without Cisco ASA AIP - SSM (IPS) of 'only' configuration/implementation Cisco ACE IPS.

  Cisco AVS/ACE emphasis on commissioning and to secure web-based applications. IP addresses do not focus on just the web applications and trying to get the multiple layers of the OSI stack. Consider the IPS as a general practitioner and the ACE/AVS as an eye surgeon, or something :)

  Here is the response from Cisco itself:

  http://www.Cisco.com/en/us/prod/collateral/modules/ps2706/ps6906/prod_qas0900aecd8045867c_ps6492_Products_Q_and_A_Item.html

  Q: how is Cisco AVS Firewall application differs from an intrusion prevention system (IPS)?

  A. IPSs are solid solutions of protection against targeted attacks of known vulnerabilities in major platforms such as Windows, Solaris, Apache or Microsoft Internet Information Services (IIS). Cisco AVS excels to protect against targeted attacks Web sites or enterprise applications. These applications can be built custom internal applications or software vendor. Signatures and security patches are generally not available for these types of applications, and building these security levels in each application, it would be almost impossible.

  Q: how is Cisco AVS Firewall application differs by a network firewall?

  A. The Cisco AVS 3120 and Firewall network such as the Firewall of Cisco PIX® and Cisco ASA 5500 Series Adaptive Security appliances are complementary products. The application Cisco AVS Firewall secures Web applications; excellent network in the network security firewall. and the Cisco AVS provides defense in depth for Web applications.

  Firewall network apply policy networks, IP addresses and ports; they have a wide range of application for many different protocols layer features. The firewall can and will be deployed in many locations, including the edge, edge of the enterprise network, branch, etc. Cisco AVS imposed the policy on data HTTP as URL, headers and parameters. Cisco AVS is deployed in the data center in front of Web applications

  Concerning

  Farrukh

• IPS Signature DataBase - ASA IPS/IOS IPS/IPS 42xx/AIP-SSM

  Hello

  Can someone briefly tell me the details of database signature (number of Signature) among the following devices

  --> ASA IPS/IOS IPS/IPS 42xx/AIP-SSM.

  Thank you

  IPS on ASA/PIX = signatures only 50 or so common

  Module AIP - SSM is same signatures as the Cisco 4200 series sensors. Few minor differences exist (such as signature support IPv6 etc.)

  Please rate if useful.

  Concerning

  Farrukh

• New deployment with the ASA and AIP - SSM module

  Hi guys and girls,

  I think to deploy an ASA with IPS module AIP - SSM to my perimeter. I'm going to use / * Style Definitions * / table. MsoNormalTable {mso-style-name : « Table Normal » ; mso-tstyle-rowband-taille : 0 ; mso-tstyle-colband-taille : 0 ; mso-style-noshow:yes ; mso-style-priorité : 99 ; mso-style-qformat:yes ; mso-style-parent : » « ;" mso-rembourrage-alt : 0 à 5.4pt 0 à 5.4pt ; mso-para-margin : 0 ; mso-para-marge-bottom : .0001pt ; mso-pagination : widow-orphelin ; police-taille : 11.0pt ; famille de police : « Calibri », « sans-serif » ; mso-ascii-font-family : Calibri ; mso-ascii-theme-font : minor-latin ; mso-fareast-font-family : « Times New Roman » ; mso-fareast-theme-font : minor-fareast ; mso-hansi-font-family : Calibri ; mso-hansi-theme-font : minor-latin ; mso-bidi-font-family : « Times New Roman » ; mso-bidi-theme-font : minor-bidi ;} Cisco IPS Manager Express (IME) to monitor the IP addresses to monitor the ASA. I have no plans on deploying a device IDS.

  Question: The IME is designed to send notices to the subject of threats? What are some of the configurations in your network? (Just prick with the last question.)

  THX...

  IME is designed only for IPS monitor (whether it be IPS appliance, module AIP - SSM on ASA or other module IPS). IME is not able on the control of ASA.

  EMI can provide advice by email about events which are fires on the IPS, while the IPS itself cannot. EMI may also keep all the events triggered by the IPS, while SPI buffer is small enough, that so if you have huge demonstrations, the buffer gets replaced pretty quickly.

  Here is more information about IME, if you are interested:

  http://www.Cisco.com/en/us/products/ps9610/index.html

• What are different between the IPS and AIP - SSC and AIP - SSM?

  Dear all,

  I'm not clear about the IPS, AIP - SSC and AIP - SSM module which are different?

  Then, when we can use IP addresses?

  When we use the AIP - SSC?

  When we can use AIP - SSM?

  Thus, a different IPS and AIP - SSC and AIP - SSM material or the same material?

  Best regards

  Rechard

  AIP - SSM is an IPS Firewall ASA module.

  IPS is available in different flavors:

  -Device of the IPS 4200 series

  AIP - SSM - module IPS Firewall ASA

  -IDSM2 - IPS module on 6500 series switch

  AIM - IPS - map IPS on router IOS

  Please rate and mark post useful.

• Downgrade IPS on AIP - SSM to 6.1.1 6.0.2

  Need to know how to return to v602 once a v611 upgrade was carried out.

  The recovery partition is also v611.

  Two methods as well as a comment. The comment is that you will want to come back to 6.0 (4), not 6.0 (2) for operational use.

  [edit] The following works of generically on autonomous sensors... I missed that this is a question for the AIP - SSM. It should still work on the AIP - SSM with adjustments for the input/output "foreigner in the area.

  To recover, a reimage using one of the tftp-able images (or a CD boot if you have a sensor 4235/4250) is the gold standard to go backward. You will lose your configuration when do you and you need to re-run the installation program.

  The other way and officially it is not supported for "damages", but it works 98% of the time, is to load the recovery image - r (IPS-K9-r-1.1-a-6.0-4-E1.pkg) and then make an application partition 'recover' the level of the "conf t". This reimage your sensor and preserve the installation of the base system. You will still lose the customizations of signature and passwords will be reset to factory default, but the network configuration is preserved, so you can do it remotely.

• silly question on module aip - ssm

  When the aip ssm module is in inline mode. fact the package first analyzed by the aip ssm module or it is first checked by the firewall rules if it is allowed and then sent to the aip ssm module.

  can someone throw some light on this.

  concerning

  Sushil

  All firewall rules are applied prior to sending the packets of the SSM.

  So if the package will be deleted by a firewall rule, the package will not be sent to the SSM.

  If the package will be changed by a firewall rule, then the change will be before being sent to the SSM.

  There are two exceptions, and this is the encryption and final release of the package.

  Encryption occurs after they are sent to the SSM, so SSM always sees a unencrypted traffic (where the ASA is encryption tunnel endpoint).

  And of course send the package by the SAA through external sound interfafes happens after the sending of the SSM.

  In the case of promiscuity, followed by the SSM, encryption and pass arrive just after that a copy is sent to the SSM.

  In the case of the line followed by the SSM, encryption and transmit occur only after that the SSM has completed the analysis and the package was not refused by the SSM.