IPsec VPN with Cisco AnyConnect and 1921 ISR G2 router
Hello
Is it possible to establish a remote access VPN IPSec using Cisco Anyconnect client with router Cisco ISR G2 1921.
If someone does share it please the sample configuration. as I've been on this topic since last week a.
My Cisco rep recommended I have not try AnyConnect a router ISR or ASR. So I used an Open Source client. Don't say that AnyConnect won't work, just the route I took on my project. I work good known configuration for a 1921 with strongSwan as a Client. It is with IPSEC and IKEV2 using certificates for authentication.
Tags: Cisco Security
Similar Questions
-
ISA500 site by site ipsec VPN with Cisco IGR
Hello
I tried a VPN site by site work with Openswan and Cisco 2821 router configuration an Ipsec tunnel to site by site with Cisco 2821 and ISA550.
But without success.
my config for openswan, just FYI, maybe not importand for this problem
installation of config
protostack = netkey
nat_traversal = yes
virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%4:!$RIGHT_SUBNET
nhelpers = 0
Conn rz1
IKEv2 = no
type = tunnel
left = % all
leftsubnet=192.168.5.0/24
right =.
rightsourceip = 192.168.1.2
rightsubnet=192.168.1.0/24
Keylife 28800 = s
ikelifetime 28800 = s
keyingtries = 3
AUTH = esp
ESP = aes128-sha1
KeyExchange = ike
authby secret =
start = auto
IKE = aes128-sha1; modp1536
dpdaction = redΘmarrer
dpddelay = 30
dpdtimeout = 60
PFS = No.
aggrmode = no
Config Cisco 2821 for dynamic dialin:
crypto ISAKMP policy 1
BA aes
sha hash
preshared authentication
Group 5
lifetime 28800
!
card crypto CMAP_1 1-isakmp dynamic ipsec DYNMAP_1
!
access-list 102 permit ip 192.168.1.0 0.0.0.255 192.168.5.0 0.0.0.255
!
Crypto ipsec transform-set ESP-AES-SHA1 esp - aes esp-sha-hmac
crypto dynamic-map DYNMAP_1 1
game of transformation-ESP-AES-SHA1
match address 102
!
ISAKMP crypto key
address 0.0.0.0 0.0.0.0 ISAKMP crypto keepalive 30 periodicals
!
life crypto ipsec security association seconds 28800
!
interface GigabitEthernet0/0.4002
card crypto CMAP_1
!
I tried ISA550 a config with the same constelations, but without suggesting.
Anyone has the same problem?
And had anyone has a tip for me, or has someone expirense with a site-by-site with ISA550 and Cisco 2821 ipsec tunnel?
I can successfully establish a tunnel between openswan linux server and the isa550.
Patrick,
as you can see on newspapers, the software behind ISA is also OpenSWAN
I have a facility with a 892 SRI running which should be the same as your 29erxx.
Use your IOS Config dynmap, penny, you are on the average nomad. If you don't have any RW customer you shoul go on IOS "No.-xauth" after the isakmp encryption key.
Here is my setup, with roardwarrior AND 2, site 2 site.
session of crypto consignment
logging crypto ezvpn
!
crypto ISAKMP policy 1
BA 3des
preshared authentication
Group 2
lifetime 28800
!
crypto ISAKMP policy 2
BA 3des
md5 hash
preshared authentication
Group 2
lifetime 28800
!
crypto ISAKMP policy 3
BA 3des
preshared authentication
Group 2
!
crypto ISAKMP policy 4
BA 3des
md5 hash
preshared authentication
Group 2
!
crypto ISAKMP policy 5
BA 3des
preshared authentication
Group 2
life 7200
ISAKMP crypto address XXXX XXXXX No.-xauth key
XXXX XXXX No.-xauth address isakmp encryption key
!
ISAKMP crypto client configuration group by default
key XXXX
DNS XXXX
default pool
ACL easyvpn_client_routes
PFS
!
!
Crypto ipsec transform-set esp-3des esp-sha-hmac FEAT
!
dynamic-map crypto VPN 20
game of transformation-FEAT
market arriere-route
!
!
card crypto client VPN authentication list by default
card crypto VPN isakmp authorization list by default
crypto map VPN client configuration address respond
10 VPN ipsec-isakmp crypto map
Description of VPN - 1
defined peer XXX
game of transformation-FEAT
match the address internal_networks_ipsec
11 VPN ipsec-isakmp crypto map
VPN-2 description
defined peer XXX
game of transformation-FEAT
PFS group2 Set
match the address internal_networks_ipsec2
card crypto 20-isakmp dynamic VPN ipsec VPN
!
!
Michael
Please note all useful posts
-
Hi all
I am trying to create a VPN between a PIX and a Cisco 877W tunnel but can't seem to get the tunnel. When I do a 'sho crypto session"on the Cisco 877, I get, he said session state is declining, then changed to NEGOTIATE DOWN, but it is now down again... Please find attached the configs for both ends... Are there commands to confirm that the tunnel is up other than to try to ping the remote end? I would greatly appreciate any help lift this tunnel.
Kind regards
REDA
Hello
Based on the configurations of joined, to do some changes. For example:
1. the isakmp policies do not match on the router and the pix. Make sure the hash group Diffie-Hellman and life correspond on the 877 and pix.
2. the access list for the ipsec traffic must be images of mirror of the other.
3. make sure life of ipsec on the two peers.
I hope it helps.
Kind regards
Arul
Rate if this can help.
-
IPSec VPN between Cisco ASA and Fortigate1000
Hello
I find a useful document on how to create a tunnel VPN IPSec with ASA 5510 firewall Fortigate 1000...
the configuration of the coast FG is done without any problem, BUT the document (. doc FG) said I must configure the ASA with a GRE interface and assign an internal IP address in order to communicate with the FG...
The question is: How do I configure the interface on the SAA ACCORD?
Thanks in advance, Experts...
Kind regards...
ASA firewall does not support the interface/GRE GRE tunnel.
If you need to have GRE configured, you will need to complete the GRE tunnel on router IOS.
If you want to configure just pure tunnel VPN IPSec (lan-to-lan), here is an example of configuration on the side of the ASA:
http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a0080950890.shtml
Hope that helps.
-
Remote IPSec VPN - client Windows 7 and ASA 5505
Hello
I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.
Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.
In the log, I see the warnings of this type:
TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)
I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.
Thank you for your help.
Petar Koraca
That's what you would have needed on versions 8.3 and earlier versions:
permit same-security-traffic intra-interface
Global 1 interface (outside)
NAT (outside) 1 192.168.150.0 255.255.255.0
However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_192.168.150.0_24 object
dynamic NAT interface (outdoors, outdoor)
Give it a shot and let me know how it goes.
-
IPSEC VPN with Dynamics to dynamic IP
Hello
I tried IPSEC VPN with dynamic IP to dynamic (router to router) for some time. But still can not auto-établir the tunnel.
Is someone can you please tell me if it is possible to do?
If so, please share with me the secret to do work.
Thank you!
Best regards
Rather than the Crypto map, I would use the profile of Crypto. Then, establish you an IPSEC tunnel. The beauty of the profile, is that you can run through it routing protocols, and you do not have to change constantly the cards whenever you change the topology of the network. The "* * *" in the timer event is "minute hour day week month" so "* * *" is updated every minute. In Tunnel destination, it's an IP address, not a hostname that is stored, but when you set it, you can put in a HOST name and it converts to the moment where you configure it to an IP address.
So, if you type:
config t
interface tunnel100
destination remote.dyndns.com tunneloutput
See the race int tunnel100
It shows:
interface Tunnel100
tunnel destination 75.67.43.79That's why the event handler goes and becomes the destination of tunnel every minute what ever the DDNS says that is the new IP address.
I have seen that two of your routers running DDNS. They will have to do this.
Local router:
crypto ISAKMP policy 1
BA aes 256
preshared authentication
Group 2
ISAKMP crypto key XXXXXXX address 0.0.0.0 0.0.0.0 no.-xauth
!
!
Crypto ipsec transform-set ESP-AES-SHA esp - aes 256 esp-sha-hmac
!
Profile of crypto ipsec CRYPTOPROFILE
game of transformation-ESP-AES-SHA
!
interface Tunnel100
Description of remote.dyndns.org
IP 10.254.220.10 255.255.255.252
IP virtual-reassembly
IP tcp adjust-mss 1400
source of Dialer0 tunnel
tunnel destination 75.67.43.79
ipv4 ipsec tunnel mode
Tunnel CRYPTOPROFILE ipsec protection profileIP route 192.168.2.0 255.255.255.0 10.254.220.9
Change-tunnel-dest applet event handler
cron-event entry timer cron name "CHRON" * * *"
command action 1.0 cli 'enable '.
action 1.1 cli command "configures terminal.
Action 1.2 command cli "interface tunnel100".
Action 1.3 cli command "destination remote.dyndns.org tunnel".
!--------
Remote router:
crypto ISAKMP policy 1
BA aes 256
preshared authentication
Group 2
ISAKMP crypto key XXXXXXX address 0.0.0.0 0.0.0.0 no.-xauth
!
!
Crypto ipsec transform-set ESP-AES-SHA esp - aes 256 esp-sha-hmac
!
Profile of crypto ipsec CRYPTOPROFILE
game of transformation-ESP-AES-SHA
!
interface Tunnel100
Description of local.dyndns.org
IP 10.254.220.9 255.255.255.252
IP virtual-reassembly
IP tcp adjust-mss 1400
source of Dialer0 tunnel
tunnel destination 93.219.58.191
ipv4 ipsec tunnel mode
Tunnel CRYPTOPROFILE ipsec protection profileIP route 192.168.1.0 255.255.255.0 10.254.220.10
Change-tunnel-dest applet event handler
cron-event entry timer cron name "CHRON" * * *"
command action 1.0 cli 'enable '.
action 1.1 cli command "configures terminal.
Action 1.2 command cli "interface tunnel100".
Action 1.3 cli command "destination local.dyndns.org tunnel".Thank you
Bert
-
I have a desktop with windows 7 and a Linksys E1000 router and you want to connect a laptop with windows 8, it will work router?
Yes, it should work perfectly, if wired (Ethernet) or wireless.
Click on the network icon in the Notification area
Click on the available wireless network that you want to connect
In the list of available wireless networks, click a network, and then click on connect.
Some networks have need a network security key or password. To connect to one of those networks, ask the network administrator or service provider for key security or password.
-
Setup for use with Cisco Anyconnect VPN IPsec
So, I had trouble setting up VPN on our ASA 5510. I would use IPsec VPN so that we don't have to worry about licensing issues, but what I have read you can do with and always use Cisco Anyconnect. My knowledge on how to set up VPN especially in iOS version 8.4 is limited, so I've been using a combination of command line and ASDM.
I am finally able to connect from a remote location, but once I log in, nothing else works. What I've read, you can use IPsec for client-to-lan connections. I use a pre-shared for this. Documentation is limited on what should happen after have connected you? Shouldn't be able to local access on the vpn connection computers? I'm trying to implement work. If I have VPN from home, should not be able to access all of the resources at work? According to me, because I used the command-line as ASDM I confused some of the configuration. In addition, I think that some of the default policies are confused me too. So I probably need a lot of help. Here is my current setup with the changed IP address and other things that are not related to deleted VPN.
NOTE: We are still testing this ASA and is not in production.
Any help you can give me is greatly appreciated.
ASA Version 8.4 (2)
!
ASA host name
domain.com domain name
!
interface Ethernet0/0
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Ethernet0/1
nameif outside
security-level 0
IP 50.1.1.225 255.255.255.0
!
interface Ethernet0/2
Shutdown
No nameif
no level of security
no ip address
!
interface Ethernet0/3
Shutdown
No nameif
no level of security
no ip address
!
interface Management0/0
No nameif
security-level 100
IP 192.168.1.1 255.255.255.0
!
boot system Disk0: / asa842 - k8.bin
passive FTP mode
DNS domain-lookup outside
DNS server-group DefaultDNS
!
permit same-security-traffic intra-interface
!
network of the NETWORK_OBJ_192.168.0.224_27 object
subnet 192.168.0.224 255.255.255.224
!
object-group service VPN
ESP service object
the purpose of the tcp destination eq ssh service
the purpose of the tcp destination eq https service
the purpose of the service udp destination eq 443
the destination eq isakmp udp service object
!
allowed IP extended ip access list a whole
!
mask 192.168.0.225 - 192.168.0.250 255.255.255.0 IP local pool VPNPool
no failover
failover time-out period - 1
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 645.bin
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static source any any static destination NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 non-proxy-arp-search to itinerary
!
the object of the LAN network
NAT dynamic interface (indoor, outdoor)
Access-group outside_in in external interface
Route outside 0.0.0.0 0.0.0.0 50.1.1.250 1
Sysopt noproxyarp inside
Sysopt noproxyarp outdoors
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
Crypto ca trustpoint ASDM_TrustPoint0
registration auto
name of the object CN = ASA
Configure CRL
crypto ca server
Shutdown
string encryption ca ASDM_TrustPoint0 certificates
certificate d2c18c4e
864886f7 0d06092a c18c4e30 308201f3 3082015c a0030201 d 020204 2 0d 010105
0500303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609
02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109
3131 31303036 31393133 31365a 17 323131 30303331 39313331 0d 170d 6f6d301e
365a303e 3110300e 06035504 03130741 53413535 3130312a 2 a 864886 30280609
02161b 41 53413535 31302e64 69676974 616c 6578 7472656d 65732e63 f70d0109
6f6d3081 9f300d06 092 has 8648 86f70d01 01010500 03818d b 30818902-00-818100-2
8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b
37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c
234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c 51782
3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02
03010001 300 d 0609 2a 864886 f70d0101 05050003 8181009d d2d4228d 381112a 1
cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc
18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6
beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef
af72e31f a1c4a892 d0acc618 888b53d1 9b 888669 70e398
quit smoking
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 activate out of service the customer port 443
Crypto ikev2 access remote trustpoint ASDM_TrustPoint0
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 10
Console timeout 0
management-access inside
SSL-trust outside ASDM_TrustPoint0 point
WebVPN
allow outside
AnyConnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
AnyConnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2
AnyConnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3
profiles of AnyConnect VPN disk0: / devpn.xml
AnyConnect enable
tunnel-group-list activate
internal VPN group policy
attributes of VPN group policy
value of server WINS 50.1.1.17 50.1.1.18
value of 50.1.1.17 DNS server 50.1.1.18
Ikev1 VPN-tunnel-Protocol, l2tp ipsec ikev2 ssl-client
digitalextremes.com value by default-field
WebVPN
value of AnyConnect VPN type user profiles
always-on-vpn-profile setting
privilege of xxxxxxxxx encrypted password username administrator 15
VPN1 xxxxxxxxx encrypted password username
VPN Tunnel-group type remote access
General-attributes of VPN Tunnel-group
address (inside) VPNPool pool
address pool VPNPool
LOCAL authority-server-group
Group Policy - by default-VPN
VPN Tunnel-group webvpn-attributes
enable VPN group-alias
Group-tunnel VPN ipsec-attributes
IKEv1 pre-shared-key *.
!
class-map inspection_default
match default-inspection-traffic
class-map ips
corresponds to the IP access list
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
Review the ip options
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
inspect the http
class ips
IPS inline help
class class by default
Statistical accounting of user
I would recommend buy AnyConnect Essentials. The cost of the license is nominal - list of US $150 for the 5510. (piece number L-ASA-AC-E-5510 =)
Meawwhile you can use the Cisco VPN client inherited with IKEv1 IPSec remote access VPN using profiles *.pcf.
I believe you can also use the client Anyconnect client SSL or DTLS transport access remotely (non-IPsec) without having to buy the license Anyconnect Essentials for your ASA focus.
As an aside, note that if you want to use AnyConnect Mobile (e.g. for iPhone, iPad, Android, Blackberry etc.clients) you will also get the additional license for it (L-ASA-AC-M-5510 =, also price US $150)
-
ASA 5510 Anyconnect licenses with Cisco Anyconnect VPN IP phone
Hi, hoping someone can shed some light on what I'm just more confused over trying to get by. Not sure if this goes in the section IP Telehpony or here...
We have an ASA 5510 with the base license. We need to install IP phones to home teleworkers, and I understand there are Cisco IP phones that have built-in VPN clients to enable a tunnel to the central private network. IT seems that you can't use Anyconnect VPN to do this, and I am trying to establish what upgrade licenses, we must apply to the ASA, as both Anyconnect licenses that you get for free on the SAA is not enough.
This is the phone that we seek;
I want to know is the Anyconnect Essentials license will work with these IP phones?
When I do a version of the show,
The devices allowed for this platform:
The maximum physical Interfaces: unlimited
VLAN maximum: 50
Internal hosts: unlimited
Failover: disabled
VPN - A: enabled
VPN-3DES-AES: enabled
Security contexts: 0
GTP/GPRS: disabled
SSL VPN peers: 2
The VPN peers total: 250
Sharing license: disabled
AnyConnect for Mobile: disabled
AnyConnect for Linksys phone: disabled
AnyConnect Essentials: disabled
Assessment of Advanced endpoint: disabled
Proxy sessions for the UC phone: 2
Total number of Sessions of Proxy UC: 2
Botnet traffic filter: disabled
This platform includes a basic license.
It shows "AnyConnect for Linksys phone: Disabled", it is the same for the Cisco IP phones? It is the kind of specific license, should I seek for Anyconnect on IP phones or will Essentials?
Hi Leo,
you will need 2 licenses: an Anyconnect Premium license and a permit «Anyconnect of Cisco VPN phone»
ASA 8.2 and earlier license "for Cisco VPN Phone" has been named "for phone Linksys' it's the same.
CFR. http://www.Cisco.com/en/us/docs/security/ASA/asa84/license/license_management/license.html#wp1487574
HTH
Herbert
-
IPSec VPN between Cisco and ScreenOS
Hello
I'm trying to set up a simple IPSec VPN between a Cisco 2911 router and a Juniper Netscreen ScreenOS (not exactly now the model) device. Initially the debbuging seems good (QM_IDLE), but the ISAKMP Security Association is deleted.
The guy managing the Juniper device send me an extract from his diary:
###########################################################################
2012-08-28 10:24:16 info 00536 IKE Phase 2 msg ID
System 9b 839579: negotiations failed.
2012-08-28 10:24:16 info system 00536 rejected a package of IKE loopback.11
of
: 500 to 217.150.152.45:500 with cookies
87960e39d074ca49 and 9302d26c7ce324a5
because there is no acceptable Phase
2 proposals...
It has defined the following phase 2 proposals:
IKE the value p2-proposal "G2_esp_aes256_sha_1800s" group2 esp aes256-sha-1, 1800 second
###########################################################################
And I use these:
###########################################################################
crypto ISAKMP policy 1
BA aes 256
preshared authentication
Group 2
!
ISAKMP crypto key
address 217.150.152.45 Crypto ipsec transform-set esp - aes esp - aes 256 esp-sha-hmac
card crypto ipsec vpn 2 isakmp
Description * VPN Anbindung nach PKI in Magdeburg *.
defined by peer 217.150.152.45
define security-association life seconds 1800
the value of the transform-set esp - aes
match address PKI-TRAFFIC
!
###########################################################################
Here is my Log:
#################################################################################################################
28 August 08:23:46.416: ISAKMP: (0): profile of THE request is (NULL)
28 August 08:23:46.416: ISAKMP: created a struct peer 217.150.152.45, peer port 500
28 August 08:23:46.416: ISAKMP: new position created post = 0x2A2D7150 peer_handle = 0x8000003A
28 August 08:23:46.416: ISAKMP: lock struct 0x2A2D7150, refcount 1 to peer isakmp_initiator
28 August 08:23:46.416: ISAKMP: 500 local port, remote port 500
28 August 08:23:46.416: ISAKMP: set new node 0 to QM_IDLE
28 August 08:23:46.416: ISAKMP: (0): insert his with his 31627E04 = success
28 August 08:23:46.416: ISAKMP: (0): cannot start aggressive mode, try the main mode.
28 August 08:23:46.416: ISAKMP: (0): pair found pre-shared key matching 217.150.152.45
28 August 08:23:46.416: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
28 August 08:23:46.416: ISAKMP: (0): built the seller-07 ID NAT - t
28 August 08:23:46.416: ISAKMP: (0): built of NAT - T of the seller-03 ID
28 August 08:23:46.416: ISAKMP: (0): built the seller-02 ID NAT - t
28 August 08:23:46.416: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
28 August 08:23:46.416: ISAKMP: (0): former State = new State IKE_READY = IKE_I_MM1
28 August 08:23:46.416: ISAKMP: (0): Beginner Main Mode Exchange
28 August 08:23:46.416: ISAKMP: (0): lot of 217.150.152.45 sending my_port 500 peer_port 500 (I) MM_NO_STATE
28 August 08:23:46.416: ISAKMP: (0): sending a packet IPv4 IKE.
28 August 08:23:46.448: ISAKMP (0): received 217.150.152.45 packet dport 500 sport Global 500 (I) MM_NO_STATE
28 August 08:23:46.448: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
28 August 08:23:46.448: ISAKMP: (0): former State = new State IKE_I_MM1 = IKE_I_MM2
28 August 08:23:46.448: ISAKMP: (0): treatment ITS payload. Message ID = 0
28 August 08:23:46.448: ISAKMP: (0): load useful vendor id of treatment
28 August 08:23:46.448: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 239
28 August 08:23:46.448: ISAKMP: (0): load useful vendor id of treatment
28 August 08:23:46.448: ISAKMP: (0): provider ID is DPD
28 August 08:23:46.448: ISAKMP: (0): load useful vendor id of treatment
28 August 08:23:46.448: ISAKMP: (0): IKE frag vendor processing id payload
28 August 08:23:46.448: ISAKMP: (0): IKE Fragmentation support not enabled
28 August 08:23:46.448: ISAKMP: (0): pair found pre-shared key matching 217.150.152.45
28 August 08:23:46.448: ISAKMP: (0): pre-shared key local found
28 August 08:23:46.448: ISAKMP: analysis of the profiles for xauth...
28 August 08:23:46.448: ISAKMP: (0): audit ISAKMP transform 1 against the policy of priority 1
28 August 08:23:46.448: ISAKMP: AES - CBC encryption
28 August 08:23:46.448: ISAKMP: SHA hash
28 August 08:23:46.448: ISAKMP: group by default 2
28 August 08:23:46.448: ISAKMP: pre-shared key auth
28 August 08:23:46.448: ISAKMP: keylength 256
28 August 08:23:46.448: ISAKMP: type of life in seconds
28 August 08:23:46.448: ISAKMP: life (IPV) 0 x 0 0 x 1 0 x 51 0x80
28 August 08:23:46.448: ISAKMP: (0): atts are acceptable. Next payload is 0
28 August 08:23:46.448: ISAKMP: (0): Acceptable atts: real life: 0
28 August 08:23:46.448: ISAKMP: (0): Acceptable atts:life: 0
28 August 08:23:46.448: ISAKMP: (0): fill atts in his vpi_length:4
28 August 08:23:46.448: ISAKMP: (0): fill atts in his life_in_seconds:86400
28 August 08:23:46.448: ISAKMP: (0): return real life: 86400
28 August 08:23:46.448: ISAKMP: (0): timer life Started: 86400.
28 August 08:23:46.448: ISAKMP: (0): load useful vendor id of treatment
28 August 08:23:46.448: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 239
28 August 08:23:46.448: ISAKMP: (0): load useful vendor id of treatment
28 August 08:23:46.448: ISAKMP: (0): provider ID is DPD
28 August 08:23:46.448: ISAKMP: (0): load useful vendor id of treatment
28 August 08:23:46.448: ISAKMP: (0): IKE frag vendor processing id payload
28 August 08:23:46.448: ISAKMP: (0): IKE Fragmentation support not enabled
28 August 08:23:46.448: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
28 August 08:23:46.448: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM2
28 August 08:23:46.448: ISAKMP: (0): lot of 217.150.152.45 sending my_port 500 peer_port 500 (I) MM_SA_SETUP
28 August 08:23:46.448: ISAKMP: (0): sending a packet IPv4 IKE.
28 August 08:23:46.452: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
28 August 08:23:46.452: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM3
28 August 08:23:46.484: ISAKMP (0): received 217.150.152.45 packet dport 500 sport Global 500 (I) MM_SA_SETUP
28 August 08:23:46.484: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
28 August 08:23:46.484: ISAKMP: (0): former State = new State IKE_I_MM3 = IKE_I_MM4
28 August 08:23:46.484: ISAKMP: (0): processing KE payload. Message ID = 0
28 August 08:23:46.508: ISAKMP: (0): processing NONCE payload. Message ID = 0
28 August 08:23:46.508: ISAKMP: (0): pair found pre-shared key matching 217.150.152.45
28 August 08:23:46.508: ISAKMP: (1049): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
28 August 08:23:46.508: ISAKMP: (1049): former State = new State IKE_I_MM4 = IKE_I_MM4
28 August 08:23:46.508: ISAKMP: (1049): send initial contact
28 August 08:23:46.508: ISAKMP: (1049): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication
28 August 08:23:46.508: ISAKMP (1049): payload ID
next payload: 8
type: 1
address: 92.67.80.237
Protocol: 17
Port: 500
Length: 12
28 August 08:23:46.508: ISAKMP: (1049): the total payload length: 12
28 August 08:23:46.508: ISAKMP: (1049): lot of 217.150.152.45 sending my_port 500 peer_port 500 (I) MM_KEY_EXCH
28 August 08:23:46.508: ISAKMP: (1049): sending a packet IPv4 IKE.
28 August 08:23:46.508: ISAKMP: (1049): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
28 August 08:23:46.508: ISAKMP: (1049): former State = new State IKE_I_MM4 = IKE_I_MM5
28 August 08:23:46.540: ISAKMP (1049): received 217.150.152.45 packet dport 500 sport Global 500 (I) MM_KEY_EXCH
28 August 08:23:46.540: ISAKMP: (1049): payload ID for treatment. Message ID = 0
28 August 08:23:46.540: ISAKMP (1049): payload ID
next payload: 8
type: 1
address: 217.150.152.45
Protocol: 17
Port: 500
Length: 12
28 August 08:23:46.540: ISAKMP: (0): peer games * no * profiles
28 August 08:23:46.540: ISAKMP: (1049): HASH payload processing. Message ID = 0
28 August 08:23:46.540: ISAKMP: (1049): SA authentication status:
authenticated
28 August 08:23:46.540: ISAKMP: (1049): SA has been authenticated with 217.150.152.45
28 August 08:23:46.540: ISAKMP: try inserting a peer
/217.150.152.45/500/ and inserted 2A2D7150 successfully. 28 August 08:23:46.540: ISAKMP: (1049): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
28 August 08:23:46.540: ISAKMP: (1049): former State = new State IKE_I_MM5 = IKE_I_MM6
28 August 08:23:46.540: ISAKMP: (1049): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
28 August 08:23:46.540: ISAKMP: (1049): former State = new State IKE_I_MM6 = IKE_I_MM6
28 August 08:23:46.540: ISAKMP: (1049): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
28 August 08:23:46.540: ISAKMP: (1049): former State = new State IKE_I_MM6 = IKE_P1_COMPLETE
28 August 08:23:46.540: ISAKMP: (1049): start Quick Mode Exchange, M - ID of 1582159006
28 August 08:23:46.552: ISAKMP: (1049): initiator QM gets spi
28 August 08:23:46.552: ISAKMP: (1049): lot of 217.150.152.45 sending my_port 500 peer_port 500 (I) QM_IDLE
28 August 08:23:46.552: ISAKMP: (1049): sending a packet IPv4 IKE.
28 August 08:23:46.552: ISAKMP: (1049): entrance, node-1582159006 = IKE_MESG_INTERNAL, IKE_INIT_QM
28 August 08:23:46.552: ISAKMP: (1049): former State = new State IKE_QM_READY = IKE_QM_I_QM1
28 August 08:23:46.552: ISAKMP: (1049): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
28 August 08:23:46.552: ISAKMP: (1049): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE
28 August 08:23:46.584: ISAKMP (1049): received 217.150.152.45 packet dport 500 sport Global 500 (I) QM_IDLE
28 August 08:23:46.584: ISAKMP: node set-452721455 to QM_IDLE
28 August 08:23:46.584: ISAKMP: (1049): HASH payload processing. Message ID =-452721455
28 August 08:23:46.584: ISAKMP: (1049): treatment protocol NOTIFIER PROPOSAL_NOT_CHOSEN 1
SPI 0, message ID =-452721455, his 0x31627E04 =
28 August 08:23:46.584: ISAKMP: (1049): peer does not paranoid KeepAlive.
28 August 08:23:46.584: ISAKMP: (1049): remove the reason for HIS "fatal Recevied of information' State (I) QM_IDLE (post 217.150.152.45)
28 August 08:23:46.584: ISAKMP: (1049): node-452721455 error suppression FALSE reason 'informational (en) State 1.
28 August 08:23:46.584: ISAKMP: (1049): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
28 August 08:23:46.584: ISAKMP: (1049): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE
28 August 08:23:46.584: ISAKMP: node set 494253780 to QM_IDLE
28 August 08:23:46.584: ISAKMP: (1049): lot of 217.150.152.45 sending my_port 500 peer_port 500 (I) QM_IDLE
28 August 08:23:46.584: ISAKMP: (1049): sending a packet IPv4 IKE.
28 August 08:23:46.584: ISAKMP: (1049): purge the node 494253780
28 August 08:23:46.584: ISAKMP: (1049): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
28 August 08:23:46.584: ISAKMP: (1049): former State = new State IKE_P1_COMPLETE = IKE_DEST_SA
28 August 08:23:46.584: ISAKMP: (1049): remove the reason for HIS "fatal Recevied of information' State (I) QM_IDLE (post 217.150.152.45)
Intertoys_Zentrale_Waddinxveen_01 #.
28 August 08:23:46.584: ISAKMP: Unlocking counterpart struct 0x2A2D7150 for isadb_mark_sa_deleted(), count 0
28 August 08:23:46.584: ISAKMP: delete peer node by peer_reap for 217.150.152.45: 2A2D7150
28 August 08:23:46.584: ISAKMP: (1049): node-1582159006 error suppression FALSE reason 'IKE deleted.
28 August 08:23:46.584: ISAKMP: (1049): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
28 August 08:23:46.584: ISAKMP: (1049): former State = new State IKE_DEST_SA = IKE_DEST_SA
#################################################################################################################
Is there something special that needs to be addressed when creating a VPN for Juniper devices?
Greetings
Thomas
The peer IPSec a PFS enabled, do the same in your crypto-map:
card crypto ipsec vpn 2 isakmp
PFS group2 Set
--
Don't stop once you have upgraded your network! Improve the world by lending money to low-income workers:
http://www.Kiva.org/invitedBy/karsteni -
Router configuration Cisco for the IPSec VPN with VPN in Windows 7 builtin client
Where can I find an example config for IPSec VPN where Windows 7 native client to connect to the Cisco routers. I use the cisco 881w, in this case.
Thomas McLeod
Native Client Windows supports only L2TP over IPSec. Example at the end of this doc may be enough for you:
I've not personally configured L2TP/IPSec on IOS, only on ASA, so cannot be 100% sure that the config in the link works, but the general idea should be ok.
-
HotSpot iOS 9.3.1 works do not with Cisco AnyConnect
Does anyone else have this problem? Since the upgrade to 9.3.1 iOS I am more able to use one of the hotspot from my iPhone to connect to the VPN from my company using Cisco AnyConnect. I can still connect via Wi-Fi, but not with the iPhone 5s or 6s hotspot feature.
Ideas?
TIA,
DM
Hello, I'm from the Italy, and I have the same problem on my 5 64 GB iPhone.
I have updated to iOS 9.3.1 and now I don't have the Hotspot feature in the phone settings Menu.
What is happen? I work with this feature and now I need to change the phone!
-
WILL IPSec VPN with mapped IP question
Hello
I am trying to configure two Cisco routers (1801 & 837) for VPN IPSec de ERG. One of them has a static IP and the other is a DSL connection; so a dynamic IP address. We have a few additional static IP assigned to us through DSL connection. So I try to use a static NAT to get the VPN connection. Unfortuantely, the VPN connection does not come to the top. Can anyone help... ? The configuration of the two routers is attached here.
R1
crypto ISAKMP policy 10
BA 3des
preshared authentication
Group 5
life 3600!
XXXX address 11.22.33.44 isakmp encryption key
!
Crypto ipsec transform-set 10 ah-sha-hmac esp-3des esp-sha-hmac
!
Crypto ipsec profile myprof
the value of the transform-set 10!
interface Tunnel10
IP 192.168.100.1 address 255.255.255.0
tunnel source 22.33.44.55
tunnel destination 11.22.33.44
protection of ipsec profile myprof tunnelIP nat inside source 192.168.3.1 static 22.33.44.55
R2
crypto ISAKMP policy 11
BA 3des
preshared authentication
Group 5
life 3600
!
XXXX address 22.33.44.55 isakmp encryption key
!
Crypto ipsec transform-set 10 ah-sha-hmac esp-3des esp-sha-hmac
!
Crypto ipsec profile myprof
the value of the transform-set 10!
interface Tunnel10
192.168.100.2 IP address 255.255.255.0
tunnel source 11.22.33.44
tunnel destination 22.33.44.55
protection of ipsec profile myprof tunnelFYI:-J' I try the same config with a loop back, also without success. But if I just change the IP address of the source R1 to be the dynamic IP address, it works fine. But, since it is a dynamic IP, I can't implement this.
Thank you in advance to you all...
Nimal
Hi Chris,
If public IP address 22,33,44,55 is routable R2, you can use the p2p gre + ipsec vpn. You can test it by creating an address of loopback on R1
lo10 int
22.33.44.55 Add IP 255.255.255.255
and ping 22.33.44.55 source R2 11.22.33.44.
If this public IP address is routable, you can use your configuration.
HTH,
Lei Tian
-
ASA IPSEC VPN with public IP dynamic
Hey,.
I have never deployed IPSEC VPN tunnel using ASA on two sides of a side using public IP dynamic production. I normally deploy VPN Tunnels with both sides using public static IP addresses (not always a public IP address on ASA directly however).
So I wonder how stable it works with a static public IP and the other side uses dynamic public IP?
Thank you
Shuai
If you use certificates and psk or main mode and aggressive it will work very well. I have a number of production sites using this method.
Sent by Cisco Support technique iPad App
-
IPSec VPN with DynDNS host problems after change of address
Hi guys,.
I have a weird problem on an IOS router.
I need to implement IPSec VPN L2L.
Because of the security requirements of each site needed a clean pre-shared key. Sites dynamic IP and it's
why I use dyndns.
ISAKMP crypto key KEY hostname XXXXXXXXXXX.dyndns.org
CMAP_1 1 ipsec-isakmp crypto map
define peer dynamic XXXXXXXXX.dyndns.orgFirst of all, it works fine, but after the change of IP address it no longer works.
Debugging, I discovered that it resolves the new IP address but IPSec attempts to connect to the previous INVESTIGATION period.
I tried this on two other IOS, 15.0 and 12.4
This debugging output:
01:02:39.735 Mar 1: IPSEC: addr of Peer Link70 (70.1.1.3) is out of date, triggering DNS
* 01:02:39.735 Mar 1: IPSEC: Peer has the address 70.1.1.3 (DNS cache). New IP address
* 1 Mar 01:02:41.731: IPSEC (sa_request):,.
(Eng. msg key.) Local OUTGOING = 1.1.1.2, distance = 70.1.1.200, OLD IP
local_proxy = 0.0.0.0/0.0.0.0/0/0 (type = 4),
remote_proxy = 10.254.70.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des esp-sha-hmac (Tunnel),
lifedur = 240 s and KB 4608000,
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 0
* 1 Mar 01:02:41.739: ISAKMP: (0): profile of THE request is (NULL)
* 01:02:41.739 Mar 1: ISAKMP: created a struct peer 70.1.1.200, peer port 500
* 01:02:41.739 Mar 1: ISAKMP: new created position = 0x673FB268 peer_handle = 0 x 80000008
* 01:02:41.739 Mar 1: ISAKMP: lock struct 0x673FB268, refcount 1 to peer isakmp_initiator
* 01:02:41.743 Mar 1: ISAKMP: 500 local port, remote port 500
* 01:02:41.743 Mar 1: ISAKMP: set new node 0 to QM_IDLE
* 01:02:41.743 Mar 1: insert his with his 650AE400 = success
* 01:02:41.747 Mar 1: ISAKMP: (0): cannot start aggressive mode, try the main mode.
* 01:02:41.747 Mar 1: ISAKMP: (0): no pre-shared with 70.1.1.200! PROBLEM!
* 1 Mar 01:02:41.747: ISAKMP: (0): pre-shared key or Cert No. address. PROBLEM!
* 1 Mar 01:02:41.747: ISAKMP: (0): construct_initial_message: cannot start main mode
* 01:02:41.751 Mar 1: ISAKMP: Unlocking counterpart struct 0x673FB268 for isadb_unlock_peer_delete_sa(), count 0
* 01:02:41.751 Mar 1: ISAKMP: delete peer node by peer_reap for 70.1.1.200: 673FB268
* 01:02:41.751 Mar 1: ISAKMP: (0): serving SA., his is 650AE400, delme is 650AE400
* 01:02:41.755 Mar 1: ISAKMP: (0): purge the node-267512777
* 01:02:41.755 Mar 1: ISAKMP: error during the processing of HIS application: failed to initialize SA
* 01:02:41.755 Mar 1: ISAKMP: error while processing message KMI 0, error 2.
* 1 Mar 01:02:41.759: IPSEC (key_engine): had an event of the queue with 1 KMI messages...
Success rate is 0% (0/5)I'm building a lab to find a solution for this.
The other side is a VPN Linksys router, I tried with an IOS router on both sites also, but I got same results.
I tried with DPD, ISAKMP profiles don't... no help.
Hi Smailmilak83,
Configuration of a static encryption with a specific peer card creates a society of surveillance for the peer. Dns lookup he's now only the first time, he tries to connect, after which it's just going to be her generate a new key. If she would ideally use the value peer in the his and not the config or a dns lookup. So, it is wise to use a dynamic encryption card.
Please try to use a dynamic encryption instead of a static map. Although there are some limitations including crypto being initiated only at the other end, we can work around keeping the tunnel directly.
Hope that helps.
Sent by Cisco Support technique iPhone App
-Please note the solutions.
Maybe you are looking for
-
App Store problems not search results or slow download
Since the update to 9.3.3 iOS App Store (East coast of United States for me) gave me a lot of problems and errors with the search for updates and installation of applications. App detail pages also not load. What a coincidence, the update iOS or some
-
Hi I have an iphone 6s with 9.2.1 yesterday, I do not see in person can call list or when I made call or call... But that the contact is saved in my directory... I turn on and off the phone twice but it's not working. Please give me Sollution as soon
-
I want to listen to a live event, but all the tutorials I've seen say to use a cable thunderbolt. My 2010 iMac doesn't have a thunderbolt cable port. Y at - it an adapter or another cable I can use?
-
2DP ports M93P video card update
Dear community, I got my M93P with 620 nvidia graphic card. It does not work for me because I need two monitors to be at the same resolution and the map only has 1 VGA and 1 port of DP. I need Exchange of the card to one that has 2 ports of DP. The n
-
My points said decision but I never
My points said decision but I never