IPv6 and IPV4 aid
Hello everyone,
I use a MacBook Pro 15 of retina in 2013. My ISP provides IPV6 connectivity yet, so I created a help service of Hurricane Electric IPV6 tunnel. I created a raspberry Pi to give IPV6 addresses on my subnet and everything works as expected. I have IPV6 connectivity on my MacBook and I can browse IPV6 sites. I did a test on http://ipv6-test.com . The results are positive, but he said that my browser (latest version of Google Chrome, but the problem is too much on Safari and Firefox) is not compatibility help. If I try the test again on Windows, Android, ecc. the warning message disappears.
The problem is that I can't browse websites using my MacBook. For example, the Apple site has not been appearing: I ran wireshark and Chrome was trying to load everything using IPV6, without success. Also try to access https://eolo.it/ (my ISP site) generates errors: it does not always work on my MacBook, while open it under Windows and IPV6 has no problem at all. I think that my MacBook (or in general OSX El Capitan) is not able to fall back to iPV4 when site an IPV6, but it does not work. I've read about 'Happy eyeballs' and I would like to know how to solve my problem.
I know that I could move to IPV6, but I prefer it to be, and in, I would like to be able to use iPV6 when my ISP provide me with an IPV6 address.
Thanks in advance.
I don't remember, in Sys Prefs > network > advanced, is there still a way to put automatic IPv6?
Tags: Older Software
Similar Questions
-
Limited Internet connectivity.
"limited access" means that your computer does not get an IP address from the router. This means usually a bad network password is stored in the PC and the router is rejected.
To diagnose the problem, try to connect your computer to another network. If it works, then you know that it is specific to your network. If it isn't, which would indicate a problem with installing wireless in your laptop. Try to remove and install the latest driver wireless.
Try to delete the particular network of list of computer networks. Then refresh the list to be able to enter the password again.
If this does not work, recycling the modem/router.
If all else fails, you can buy a plug in USB wireless network device for usually under $40, which will offer an additional wireless for you installation. They can actually be very beneficial because they work often better than the high ones. Make sure the USB network device you purchase is a N.
-
IPv6 and AirPort Extreme Gen 5 connection drops
My ISP is over native IPv6 but the AirPort Extreme (AE) abandons the connection every 30 minutes or more.
I've tried different settings IPv6 and the only one that gave stable results is to:
-Block all the incoming IPv6
-Allow teredo and IPSec tunnels
-IPv6 tunnel fashion game
If IPv6 is set to native, airport utility shows the Internet connection disabled. So far with the tunnel mode, it seems to work. IPv6 - test.com results show 6to4 good feature as well.
Someone else had problems with the products of the AE and IPv6 settings?
He would have nothing to do with IPv6, but the problem was triggered by the latter.
This modem do you have? Brand and model please.
And who is your Internet provider because your Setup sounds weird... it should not be necessary to the IPv6 block.
-
I'm having the problem of local connection on my Dell PC with Vista. ISP is Verizon FIOS. FiOS representative told me to disable Ipv6 and the problem stops. Is this correct?
original title: local area connection problemHello
1. What is the exact problem you are facing with local connection?
2. how many computers have you plugged into the network?
Please provide the information of network event logs to help you best.
Click on the link below.
In the meantime, run the troubleshooter mentioned in the link below.
http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems
-
We are preparing for a migration to IPv6, and I'll try to find if there is an OS ASA recommended by Cisco for IPv6 support. My firewall is currently version 7.2 (3). I know that this version contains IPv6 commands, but I want to make sure that it supports everything that I need.
Thank you!
Dan
Here is what is supported in the release 7.2.x for IPv6:
http://www.Cisco.com/en/us/docs/security/ASA/asa72/configuration/guide/IPv6.html
The latest version of the SAA has more supports IPv6.
Here's the configuration for ASA 8.3 guide and the IPv6 configuration can be found on a number of sections:
http://www.Cisco.com/en/us/docs/security/ASA/asa83/configuration/guide/config.html
(Under the configuration of interfaces, adding section a section of list of access IPv6 configuration section IPv6 Neighbor Discovery, etc.).
Hope that helps.
-
IPv6 on IPv4 VTI ipsec traffic
Hello
I have a VTI ipsec on ipv4 I use for LAN traffic between sites.
Something like:
interface Tunnel0
IP 172.16.1.1 255.255.255.0
tunnel source 80.80.80.1
tunnel destination 90.90.90.1
ipv4 IPsec tunnel mode
protection of IPsec profile vti_profile tunnel
Now I want to tunnel IPv6 on those as well.
I tried the simple addition of an IPv6 on Tunnel0 address, but that did not work.
I can create a tunnel on the IPv4 link like this:
Tunnel1 interface
source of Tunnel0 tunnel
tunnel destination 172.16.1.2
ipv6ip tunnel mode
enable IPv6
3000::1/112 IPv6 address
But I was wondering if there was another solution?
See you soon,.
Sylvain
Sylvain,
I don't think you can carry IPv6 on IPv4 ASIT.
I believe that you have received a message that's not supported - negotiated proposals are explicitly for IPv4:
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
There is a tunnel mode ipsec, ipv6, BUT it is ipv6 via IPv6 only.
I think that your best choice is to run o IPsec instead of ASIT GRE if you want IPv6 tunnel at the same time.
(Please note that I have not kept up-to-date with all the improvements of VTI recently, maybe things have changed)
Marcin
-
OK, this is a really stupid question, but I'm trying to add a soundtrack to a project in first 10 elements, and the aide said section "click music in the action bar to display the Panel of music." I can't find a 'Music' box to click around. Can someone tell me please in the right direction?
cdmw
If your program is first items 10
a. you are in help for first items 11, not 10, and his description of the Action/music bar tab.
or
b. more unlikely since first elements 11 was not yet released, there is a typing error in the
First Elements 10 help.
In first 10, chronology workspace Elements, see Audio Tools (speaker icon) above the timeline and his choice of SmartSound.
Please review and study and then we can then what to do next.
Thank you.
RTA
-
TIVO requires certain ports to be unblocked. So I try to add the ports requiring TIVO. But when you try to add the default Type of firewall IPv6 Port Mapping ports and I can't change the value of the IPv4 Port Mapping because the input field is grayed out and no is not accessible. With Port IPv6 mapping I enter values in all areas except for the IPv6 address because I do not know what value to enter. I think the button 'save' ' is not available to hit because the IPv6 address field is empty or not valid. Note: my router Mode is ' Off (Bridge Mode). Same questions if my router DHCP Mode.
I changed my router Mode DHCP and NAT, then on the Type of firewall on the default page add ports, IPv4 Port Mapping and I could add ports but with this setting, I couldn't connect to internet in my Airport Extreme: my status remains orange light flashing.
I use Comcast and my Airport Extreme is connected to my Comcast router using ethernet.
I use my Airport Extreme as a router (wired and WIRELESS) and as a backup device.
My TIVO is connected to my Airport Extreme using ethernet.
How can I add the Ports requiring TIVO.
Golden in the networking rule. ....... Never try to configure port mapping when you have two devices on the same network the two acting as a router.
Unfortunately, this is exactly what you're trying to do.
You have three options:
(1) run the Comcast router "as what" and configure the port on the device of Comcast mapping... .the airPort Extreme must be configured in Bridge Mode when you do this.
(2) lance to the AirPort Extreme router Mode of DHCP and NAT and configure the ports on the airport map... the peripheral Comcast must be configured to operate as a simple modem in Bridge Mode when you do this.
(3) lance to the AirPort Extreme router Mode of DHCP and NAT and configure the ports on the airport map... swap Comcast modem/router you have now for a simple modem (it will have only a single Ethernet port).
In other words, either the Comcast is defined as the router and AirPort Extreme is in Bridge Mode... or... the AiPort Extreme is configured as a router and Comcast must be configured in Bridge Mode.
If you choose Option 1, then we can not help you on a matter of Comcast router. In bridged Mode, the AirPort Extreme requires no configuration.
If you choose Option 2 or Option 3, then we the following port values that the Tivo device needs:
Public or UDP ports
Public TCP
UDP private
Private TCP
In addition, you need to find the MAC address for the TIVO. It is a long code that looks something like this, for example:
A1: B2: C3: D4: E5: F6
A link to the Tivo instructions for port mapping would also be very useful. I have done this with a TIVO in the past, but is for some years.
If all goes well, an expert of TIVO will post to lend a hand.
-
The problem is that they both take an IP is static and a dynamic that is playing with the other computers.Computer performs an IP address and I have someone lose their Internet connection. Is a static IPv4 and ipv6 is dynamic.
Thank you
Ok.. What is
Start > type cmd into the search bar > right click and select "Run as Administrator" > at the prompt of > ipconfig/release > reboot and see if it's still there. -
activate ipv6 and home group does not work windows 7
homegroup
Hello Steve409
Please write to the Microsoft Forums.
To help you better, please answer this question.
Which edition of Windows 7 you are using?
I guess you want to know how to enable ipv6.
I'll give you the steps to activate IPV6
1 right-click on the network icon
2. select open network and sharing Center.
3. in the window that appears, select "change the map settings.
4. in the network connections window, select the 'connection to the Local network' for the interface NETWORK integrated (or whatever it's called), then "change settings of this connection" or file > properties.
5. in the connection properties page, check the box 'Protocol Version 6 (TCP/IPv6) Internet'.
It may be useful
Thanks and greetings
Dinesh
Microsoft technical support
Visit our Microsoft answers feedback Forum and let us know what you think
-
I have three computers with Windows 7 Home Premium installed recently and works well. I want to create a homegroup. When I try to join one of the computers to an existing homegroup, I get the message "your network must have IPv6 enabled connection". I have tried the stop and restart, TCP/IPv6, but I can't the homegroup to work. I cut off all firewalls. How can I verify that TCP/IPv6 works, and how I can fix this problem if it is not.
The homegroup on two other computers worked without any problems. All are connected by ethernet cable to a Verizon FiOs router. The computer problem has no other problem of connectivity - internet and e-mail work correctly. I also see the computer of 'bad' on the map of the network on the part of others.
Hi SandyGrim,
Welcome to the Microsoft Answers site.
one) that you get an error message? If Yes, what is the exact error message?
I would like to explain that IPv6 has been dependent on the NPRI (redundant network routing protocol) service. To resolve this problem, we will see the following steps.
Step 1:
Temporarily disable the firewall and third-party antivirus on the computer for a test.
Step 2:
Check the relevant services are enabled.
1. click on "Start", type "services.msc" (without the quotes) in the search bar and press ENTER.
2. If you are prompted for an administrator password or a confirmation, type your password, or click on continue.
3. right click the "Peer Networking Grouping" service and choose Properties.
4. Please check if the service is started; If this isn't the case, please click on the Start button and see if it works.
5. you can also choose automatic next to startup type.
6. click on OK.
7. repeat the above steps with another service: PNRP Machine Name Publication Service.
Step 3:
Modify the key to register IPv6 to enable IPV6
Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756
1. Click Start, type regedit in the search bar and then click regedit in the list programs.
2. If you are prompted for an administrator password or a confirmation, type your password or click on continue.
3. Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\TCPIP6\Parameters
4. check if the "DisabledComponents" registry key exists. If so, move on the next steps.
5. double-click "DisabledComponents" registry key and change the value to 0.
(If the key does not exist, please create the above key and assign the value 0)
6. exit the registry editor and then restart the computer.
For more information, we can refer to the link below:
Homegroup get a must have IPv6 active fault
To disable IPv6 check the article mentioned below.
How to disable certain Internet Protocol version 6 (IPv6) components in Windows Vista, Windows 7 and Windows Server 2008
http://support.Microsoft.com/kb/929852
To troubleshoot IPv6, see the following articles.
Diagnose connections
http://msdn.Microsoft.com/en-us/library/ms881706.aspx
Troubleshooting IPv6
http://msdn.Microsoft.com/en-us/library/ms899599.aspx
Hope this information is useful.
Thanks and regards.
Thahaseena M
Microsoft Answers Support Engineer.
Visit our Microsoft answers feedback Forum and let us know what you think. -
Hi all
Anyone know if the view is compatible with IPv6?
IPv6 is a good response to massive infrastructure VDI with frequent updating, recompose, etc...
I mean, can we use a complete solution of IPv6 including?
- Connection brokers
- View customer (Zero customer)
- View agent (Windows 7)
I know that with Teradici 3.5 firmware, IPv6 is supported on the zero client, and of course on Windows 7 this is also the case.
I can barely find information on the rest of the components and especially the broker for connections.
Thank you
Eric
Sorry, cannot discuss road maps.
Track down the local VMware team and ask them a NDA submission.
Linjo
- Connection brokers
-
I read a LOT of other people who have this problem, and I've seen no good answer. (Answers require several days of analysis, and I don't have much time.)
Whenever Firefox updates automatically, it loses most of my passwords!
Yes, I read that there is a 'profile' blah blah blah. But does that mean that I have to go through all kinds of loops, when this automatic update occurs?
If so, I gladly leave Firefox and switch to another browser.
I never had this problem with any browser, never with Safari, I left only because he did not work with many websites.
I use a Mac, OS 10.6.8
Thank you
Why not update manually? If you do it this way, the profile is not in use when the update takes place, so nothing in it should be corrupted.
-
TouchEvent event and FieldChangeListener aid management
I have a class screen that extends screen and implements FieldChangeListener. I have a function that captures
TouchEvent.
protected boolean touchEvent(TouchEvent te)
I also have a function as implents FieldChangeListener
' Public Sub fieldChanged (field field, int context)
I get all the touchevents in the touchEvent function, but once I did information there, I need to go to the normal processing, is there a way to implements this? or at least goto the function fieldChanged with the right parameters (scope, context)
While when I click on an event, it goes to fieldChanged. I use picture.setChangeListener (this) to the fields I
Thank you
event management methods return true if the event has been consumed or handled and false otherwise.
If you want the event to wander in the chain must return false in your implementation of tocuhEvent (I don't know if the touch events are addressed later) -
problem with windows 7 starter Autoconfiguration IPv4 address and IPv4 address
I can not change or disable Autoconfiguration IPv4 address in the ipconfig-all command
I can't connect to the network any ip iput ditect as duplicate.
can anyone help?
ipconfig-all
Windows IP configuration
Name of the host...: xxx - PC
Primary Dns suffix...:
Node... type: hybrid
Active... IP routing: No.
Active... proxy WINS: No.Ethernet connection to the Local network card:
The connection-specific DNS suffix. :
Description...: Realtek RTL8168B/8111 Family PCI - E Gigab b
It Ethernet NIC (NDIS 6.20)
Physical address.... : 00-50-DB-00-15-2E
DHCP active...: No.
Autoconfiguration enabled...: Yes
Autoconfiguration IPv4 address. . : 169.254.242.251 (Duplicate)
... Subnet mask: 255.255.0.0.
IPv4 address...: 192.168.20.155 (Duplicate)
... Subnet mask: 255.255.255.0.
... Default gateway. :
NetBIOS over TCP/IP...: enabledTunnel adapter isatap. {F0C7F7B4-DF88-4908-A9C1-F8B888710CAC}:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Microsoft ISATAP adapter
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: YesHello
If a computer is only connected to a switch, the automatic configuration is not valid.
Autoconfiguration applies when a computer is connected to a server that can provide the configuration.
Wireless routers have a DHCP server that provides a valid IP address.
Ordinary switch is a transparent network device that cannot provide any configuration.
When there is no DHCP server, the computer must be configured with a static IP address.
Look at this page, http://blog.mclaughlinsoftware.com/2009/11/26/windows-7-static-ip/
Follow the path as described in step 5 (Do not pay attention to specific numbers, your number is to be determined in accordance with your network plan).
Maybe you want to provide an explanation of what you are trying to reach.
Jack-MVP Windows Networking. WWW.EZLAN.NET
Maybe you are looking for
-
Report is not visible in firefox 5, how to solve this?
I have change for firefox 5 this morning, he made me well this google toolbar was not compatible but did not mention Trusteer report. It did not work so I "fixed", even if it seems to work he put in place an error on a packet of mail and asked me to
-
Skype to play with Google Chrome
I came across a problem shortly after the update of Skype, I think. In Google Chrome, whenever I'm trying to look up a word in the omnibox, it brings me to the page but a window popups down saying "{did you mean go to http://{word, I searched}? This
-
WRT54GS V7.50.6 - WIFI problem
Hello.I have problem with router WRT54GS V7.50.6.First of all.Active DHCP.I have Off SSIDI have a personal WPA keyI allowed that MAC (and added mac from my computer)I don't see on the DHCP Tables all unknown host.There is no Firmware more recent I kn
-
Hello First of all, let me apologize if this question has already been addressed in another thread (probably, but I am unable to find a satisfactory answer). I recently encountered problems with the Vista Home Premium OS that came pre-installed on my
-
How can I find out what programs start or stop to start the computer?
How can I find out what programs start or stop to start the computer? Now there's like 68 programs that start at startup of the computer, I know that this is the way to much, I just need if bought a laptop with windows7premium installed and the probl