problem with windows 7 starter Autoconfiguration IPv4 address and IPv4 address
I can not change or disable Autoconfiguration IPv4 address in the ipconfig-all command
I can't connect to the network any ip iput ditect as duplicate.
can anyone help?
ipconfig-all
Windows IP configuration
Name of the host...: xxx - PC
Primary Dns suffix...:
Node... type: hybrid
Active... IP routing: No.
Active... proxy WINS: No.
Ethernet connection to the Local network card:
The connection-specific DNS suffix. :
Description...: Realtek RTL8168B/8111 Family PCI - E Gigab b
It Ethernet NIC (NDIS 6.20)
Physical address.... : 00-50-DB-00-15-2E
DHCP active...: No.
Autoconfiguration enabled...: Yes
Autoconfiguration IPv4 address. . : 169.254.242.251 (Duplicate)
... Subnet mask: 255.255.0.0.
IPv4 address...: 192.168.20.155 (Duplicate)
... Subnet mask: 255.255.255.0.
... Default gateway. :
NetBIOS over TCP/IP...: enabled
Tunnel adapter isatap. {F0C7F7B4-DF88-4908-A9C1-F8B888710CAC}:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Microsoft ISATAP adapter
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
Hello
If a computer is only connected to a switch, the automatic configuration is not valid.
Autoconfiguration applies when a computer is connected to a server that can provide the configuration.
Wireless routers have a DHCP server that provides a valid IP address.
Ordinary switch is a transparent network device that cannot provide any configuration.
When there is no DHCP server, the computer must be configured with a static IP address.
Look at this page, http://blog.mclaughlinsoftware.com/2009/11/26/windows-7-static-ip/
Follow the path as described in step 5 (Do not pay attention to specific numbers, your number is to be determined in accordance with your network plan).
Maybe you want to provide an explanation of what you are trying to reach.
Jack-MVP Windows Networking. WWW.EZLAN.NET
Tags: Windows
Similar Questions
-
I am running windows vista and am warned there is a problem with windows media center, restart my computer and try again. It did not work. Help
Run the Setup again.
Open WMC > tasks > settings > General > installation Windows Media Center > rerun the installation
Does that help?
If the above does not help then try to reset WMC: -.
Open Control Panel > uninstall a program > turn Windows features on or off > scroll multimedia features > uncheck the box against Windows Media Center > follow the instructions on the screen > Reboot > open again to turn Windows features on or off in the control panel > scroll multimedia features > check the box against Windows Media Center.
Now reconfigure WMC again
-
Windows XP Installation problem with Windows 7 Starter home
I was told that I would have no problem of family Windows XP Setup on a new computer comes pre loaded with Windows 7 Starter.
When I insert the CD with Windows XP, I get the following:
Run setup.exe
I click on install Windows XP
Program is blocked due to compatibility issues.
Setup cannot continue because the version on the computer is newer than the version on CD.
Anyone know how to solve this problem and install Windows XP?
Thank you Don
Hello
I understand that you want to install Windows XP on Windows 7 Starter Edition.
(1) is the retail Windows XP version or OEM version, you are trying to install?
Unfortunately, this is not possible. As the operating system installed on your computer is newer than the operating system you are trying to install.
To resolve this problem, you need to do a clean install to install Windows XP, and you try to run Windows 7 Setup, it will not work. So, I suggest you to boot from the XP CD (if necessary, first change the boot order in the BIOS) and follow the instructions for a clean install. It will initially format the drive for you, so make sure you back up everything you don't want to lose to external media first.
I hope this helps. Try the above steps and get back to us for assistance. We will be happy to help you.
-
Problems with Windows 7 Starter screen brightness
I recently bought a Samsung N210 netbook more with WINDOWS 7 STARTER.
Before installing the Windows updates, the screen brightness is adjustable using the cursor or function keys.
After that Windows Update Setup, I can change is more brightness, it is stuck to the maximum.
Is there a solution?
How to roll back a driver under Windows 7
http://pcsupport.about.com/od/Windows7/HT/roll-back-driver-Windows-7.htmTip: Get a updated driver that you need the download page of the device manufacturer or the computer, not Windows Update.
~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
-
Problem with windows mail send not of pictures and attachments? Help, please!
Hello, yesterday I continued to get an error code when you try to update some security updates, I've used the tutorial help and went and deleted some file deep into my system, as he ordered. He has not yet fixed the error and now my windows mail will not send attachments and the police to the address info seem different? I'm lost, please help!
Hi Pishy,
1. what was the error code that you received when you try updates security?
2. what tutorial did you delete files?
3. what happens when you try to send emails with attachments? You receive messages or error codes?
You can try to perform a restore of the system to a prior restore point you have been affected by the issue.
Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.
To run the system restore, you can consult the following link:
System Restore: frequently asked questions
For more information, you can also consult the following article:
Solve problems with Windows Mail
Hope this information is useful.
-
I have a problem with Windows Media Player on laptop Lenovo G780. My laptop is under warranty (bought a month ago), but technical support Lenovo told me that the Windows Media Player program is not covered by the warranty.
And this is a problem:
When I click on Windows Media Player - to about 0.1 sec I see it opens and closes the window and nothing happens.
When I select a mp3 or wmv file and right-click with the option open with Windows Media Player - I get a message: "Server execution failed" - I checked that all services with 'Media' in the name are running.
When I select a mp3 or wmv file and right-click with the open option with Windows Media Center - Windows Media Center opens with the message: "the files needed to display video are not installed or do not work properly.
When I select a file mp3 or wmv and right-click with option open with Windows Movie Maker life - see the video
I tried to turn / WMP and WMC - did not help
Tried to run as administrator - did not help
I don't see something suspicious under eventsWhat can I do else?
Thank you
Zarek
I had the same problem and then by chance, I tried a video on YouTube and it worked for me. Here's how I went on this issue and solved my problem:
1. go to the computer, then OS (C).2. you will need to open Program Files (x 86) and Program Files.3. go to Windows Media Player in Program Files (x 86) and open the folder. Then, remove the wmplayer file. You may need to work around the error TrustedInstaller. I'll tell you that, in a moment.4. in Program Files, go to the same folder for Windows Media Player and select the same file again. Wmplayer. Copy the file in another window open. Copy ensures that if the question comes up again you can at least try to fix it again.This should be the end of your problem. If you need to circumvent the TrustedInstaller question is how:1. right click on wmplayer and select Properties > Security > advanced > owner > Edit > other users and groups.2. Enter your username and then click on check names. Click OK.3. close the dialog boxes as he has requested.4. open again the properties and click Security. Select your username from the list and click on edit. From there, select full control.This should give you full control over the removal of the original file for WMP and easily allow you to copy the other files (x 86) programs.Please let me know how it goes for your problem. -
HP MINI: problem with windows 7 starter
I have a hp laptop and I have a problem do not see the product key for window s7 starter, mini hp, is what to do, there are cases we can problem vgeike?
Hello
To activate the recovery procedure, if you can't get to Windows continually type F11 at startup until you get to the recovery screen, or from inside windows click on start > all programs > click on Recovery Manager and follow the instructions on the screen to complete the process.
http://support.HP.com/us-en/document/c01867418
The above link explains in detail the procedures
Checkurtech
-
Problems with Windows 7 Starter administrator
I have a HP Mini 200 running Windows 7 Starter.
I try to add a printer to my netbook, but I have been informed that I need administrator permission to install. I also have a message that connection manager HP does not support guest accounts.
I am aware that I don't have a guest account. I try and remove any additional account in the account settings, but nothing happens. I tried to change my privelages account but nothing happened. There is a comments file in C: /. I seem to be going round in circles. What I want is to run a printer!
Any advice?
Hello Simon,.
I suggest you to activate the integrated using the command prompt administrator account and try to add the printer in this account and check.
Follow the article to enable the built-in Administrator account.
Enable / disable the administrator account (hidden, built-in) Local in Windows 7.
If you are able to add the printer to the built-in Administrator account. I suggest to create a new account user to the built-in Administrator account.
To create the new user account follow method 2 in my first answer.
Put us up-to-date with the results after you perform these steps. We would be happy to help you further on the issue.
-
Problems with Windows Movie Maker: video/Audio, cut and cutting
I recently did some videos, but there was this thing really annoying happening in the middle of the video. Okay, let's say I put together all the clips in Windows Movie Maker for my taste, and it's how I wanted it to be. I saw it and then suddenly in the middle of the video the sound shuts down or freezes the clip or it will just empty. I have not been able to solve and so I can't do more videos without him just hide or cut.
Please help, I need to make a video for a deadline but nothing I try suddenly freezes or cuts in a specific clip. How is what is happening and what can I do to stop it. I've accidentally done something or it just freezes.
Thanks, I need all the help I can get!
I use Windows Vista. And this has only been produced recently, that my previous videos have been very well.
Well well... once again, without success. The same thing happens, it freezes in the middle of the clip. I get the FLV file by orbit actually, but I don't know who is a hoarder of corrupted file. What should I do?
==============================================
Don't know what to tell you... apparently the original .flv video clip is damaged.The following free download includes a utility to convert .flv, but to this
point that I am not convinced that you will have success.Pazera Video converters Suite 1.2
http://www.Pazera-software.com/products/vcsuite/
(click on the blue Download button not the Red)FWIW... the name of the file that you download is:
Experience of digital media of John Inzer - MS - MVP - 'Pazera_Video_Converters_Suite.zip '. -
Problem with Windows Vista Start Menu icons
The Start Menu doesn't display the 9 item in the list, why?
[img] http://i47.tinypic.com/e053f9.jpg [/ img]
Uh, after a format, it works well, I don't know what application to be like that.
and it's okay to large or small icons, it should show article 9.
-
The command line does not work. I am the administrator and it is automatically elevated command prompt. I type CHKNTFS /X c:
I get an error message: "is not recognized as an internal or external command executable program or Batch file" won't play with my registry. Any help please.
Thank you and all who responded. It seems that the chk dsk is enacted by System Mechanic (which I think is an excellent program). I learned, however, to run a command as administrator prompt. I always started it with the command run and not as a typed command.
-
The problem with Windows update - automatic updates service won't start not (error 126)
original title: the problem with Windows update
Please help me to get Windows Update operational return.
XP Media Center Edition, Version 2002, SP3
Had a problem with "Generic host process for Win32 has encountered a problem and needs to close." Follow-up of the instructions on this link:
http://support.Microsoft.com/kb/931852Seems to have cleared the error message. So far so good.
However, now a Windows Update does not work. Security Center Windows were told to go to control panel > system and use the Automatic Updates tab. But, if I go to control panel > system, the Automatic Updates tab does not appear.
I also went to the control panel > Services. Tried to start the automatic updates service. Received this error message: could not start the service automatic updates on Local computer. Error 126: The specified module could not be found
I already followed several instructions on this subject:
In the thread above, I was following the post on 30 August. According to Option A, I completed step 5 for the uninstallation of McAfee Security. At this time, my network card has stopped working. On the recommendation of the officer, I posted to the Malwarebytes forum. The officer determined Malwarebytes that I don't have a malicious software. I ended up posting on forum McAfee to get my network card works again. Then I reinstalled McAfee and start to run Windows Update.
I started with Option A, step 8 to reset Internet Explorer using http://support.microsoft.com/kb/923737. The difficulty it has worked very well.
Then Option A, step 9 says reset Windows Update using http://support.microsoft.com/kb/971058. When I ran the difficulty in default or aggressive mode, I got an error message saying: he cannot start wuauserv. The message asks me to verify that the user has privileges to take this step. Well, I checked through user accounts who am the only one user set up on this PC and I have administrator privileges. Help me please run this difficulty or recommend another way to get Windows Update works again.
[1]... looks like you are saying that my system is so wet that a clean install is the (only?) way to go.
[2] if I do a clean install, not only what I need to reinstall Windows and all my applications, I also have to reinstall the drivers... Etc. ?
[3] I think I have the disks supplied with the PC system. Is it better to use than to use the recovery partitiion?
[4A]... is there a possibility that some of [my data are] infected?
[4] preventing me from simply infect the whole PC again?
A1. Yes, and it was my recommendation in August, too.
A2. Yes.
A3. Only not really well using the restore Partition hidden to make the "destructive recovery" will include all drivers, etc., that have been installed at the factory.
A4a. Yes, a real possibility.
A4b. You run at least three 3 tests on the backup data before restoring one (1) with your installed & updated up-to-date anti-virus application (for example, Microsoft Security Essentials) and two 2 with good reputation, free online scans (e.g., ESET;) Bit Defender; Kaspersky; HouseCall; (F - Secure).
If you have saved your data on CD/DVD, the disc scanner. If you have backed up your data to a flash drive, SD card, or another external drive AND KB971029 is installed, analyze the drive.
If you have any questions or need additional help, please start a new thread in this forum: http://answers.microsoft.com/en-us/windows/forum/windows_xp-system
Once again, good luck!
-
Having a problem with Windows Live Mail lock up shortly after the start.
Having a problem with Windows Live Mail lock up shortly after the start. When I start the Task Manager to end the process, it sometimes freezes and the only way to solve the problem is to disconnect which forces the profile to close. Assuming a corrupted profile, I followed the instructions of Windows support to fix a corrupted profile and copied all the files except ntuser.*. When I try to paste them into the new user profile (all profiles are admins), I get the error message asking if I want to leave to proceed. When I click on continue, all THE files in the profile block "corrupt" to the new one, including ntuser.*, that I was not choosing. Why? If the files are rewritten empty? Tried 3 times, same result. Please notify.
I think I found it! I went in the Windows Live Forum and found a thread that looked like my problem. He suggested going to msconfig and take off Live Mail list start. I couldn't find it on the list, but the top element was "" default EXE"something of an unknown manufacturer. I took it out of the startup list, and Live Mail works again! Thanks for your help!
-
Is anyone else having problems with Windows 8 when your typing and e-mail? For some reason, it comes out constantly to the tile screen while I type making me about starting more.
Hi Chaz,
I thank you for your message and gives us a chance to help you. I see that the Mail app closes while you are typing an email.
Please answer these questions to get a better understanding of the issue.
1 have changes made to your computer before this problem?
2 shut down other applications while they are in use?
3. do you get an error code?You can try these methods to check whether the problem is resolved.
Method 1: Run the troubleshooter of app.
http://download.Microsoft.com/download/F/2/4/F24D0C03-4181-4E5B-A23B-5C3A6B5974E3/apps.diagcab
Open this link to launch the troubleshooter.
Method 2: Update the application.
Method 3: Reinstall the application.
This link has the steps that you can follow to update and reinstall the application.
http://Windows.Microsoft.com/en-us/Windows-8/what-troubleshoot-problems-app
Feel free to use the forum for any other issue of Windows, you may have.
-
Problem with Windows Explorer. Explorer Windows stopped working
Original title: Windows Explorer problem... _ I get the message; Explorer Windows has stopped working. My wifes user account has stopped working all together. __
Signature of the problem:
Problem event name: APPCRASH
Application name: Explorer.EXE
Application version: 6.1.7600.16450
Application timestamp: 4aebab8d
Fault Module name: Explorer.EXE
Fault Module Version: 6.1.7600.16450
Timestamp of Module error: 4aebab8d
Exception code: c000041d
Exception offset: 000000000002cc2b
OS version: 6.1.7600.2.0.0.768.3
Locale ID: 1033
Additional information 1: 9 d 35
More information 2: 9d352eeb48f756eef3e09921a012e0a8
Additional information 3: ca2c
Additional information 4: ca2c069770e7f64d60f91ac290056ba5Hello
References to Vista also apply to Windows 7.
What antivirus/antispyware/security products do you have on the machine? Be one you have NEVER
on this machine, including those you have uninstalled (they leave leftovers behind which can cause
strange problems).----------------------------------------------------
Follow these steps:
Try these to erase corruption and missing/damaged file system repair or replacement.
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html==========================================
After the foregoing:
How to troubleshoot a problem by performing a clean boot in Windows Vista or
Windows 7
http://support.Microsoft.com/kb/929135Use advanced tools to solve performance problems in Windows 7
http://www.howtogeek.com/HOWTO/6152/use-advanced-tools-to-troubleshoot-performance-problems-in-Windows-7/Problems with the overall speed of the system and performance
http://support.Microsoft.com/default.aspx/GP/slow_windows_performance?p=1How to troubleshoot performance issues in Windows Vista
http://support.Microsoft.com/kb/950685Optimize the performance of Microsoft Windows Vista
http://support.Microsoft.com/kb/959062
To see everything that is in charge of startup - wait a few minutes with nothing to do - then right-click
Taskbar - the Task Manager process - take a look at stored by - Services - this is a quick way
reference (if you have a small box at the bottom left - show for all users, then check that).How to change, add or remove startup programs in Windows 7
http://www.SevenForums.com/tutorials/1401-startup-programs-change.htmlA quick check to see that load method 2 is - using MSCONFIG then put a list of
those here.
--------------------------------------------------------------------Tools that should help you:
Process Explorer - free - find out which files, key of registry and other objects processes have opened.
What DLLs they have loaded and more. This exceptionally effective utility will show you even who has
each process.
http://TechNet.Microsoft.com/en-us/Sysinternals/bb896653.aspxAutoruns - free - see what programs are configured to start automatically when you start your system
and you log in. Autoruns also shows you the full list of registry and file locations where applications can
Configure auto-start settings.
http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
Process Monitor - Free - monitor the system files, registry, process, thread and DLL real-time activity.
http://TechNet.Microsoft.com/en-us/Sysinternals/bb896645.aspxThere are many excellent free tools from Sysinternals
http://TechNet.Microsoft.com/en-us/Sysinternals/default.aspx-Free - WhatsInStartUP this utility displays the list of all applications that are loaded automatically
When Windows starts. For each request, the following information is displayed: Type of startup (registry/Startup folder), Command - Line String, the product name, Version of the file, the name of the company;
Location in the registry or the file system and more. It allows you to easily disable or remove unwanted
a program that runs in your Windows startup.
http://www.NirSoft.NET/utils/what_run_in_startup.htmlThere are many excellent free tools to NirSoft
http://www.NirSoft.NET/utils/index.htmlWindow Watcher - free - do you know what is running on your computer? Maybe not. The window
Watcher says it all, reporting of any window created by running programs, if the window
is visible or not.
http://www.KarenWare.com/PowerTools/ptwinwatch.aspMany excellent free tools and an excellent newsletter at Karenware
http://www.KarenWare.com/===========================================
Think about it an absolute must - manually update your drivers.
Vista and Windows 7 updated drivers love then here's how update the most important.
This is my generic how updates of appropriate driver:
This utility, it is easy see which versions are loaded:
-Free - DriverView utility displays the list of all device drivers currently loaded on your system.
For each driver in the list, additional useful information is displayed: load address of the driver,
Description, version, product name, company that created the driver and more.
http://www.NirSoft.NET/utils/DriverView.htmlFor drivers, visit manufacturer of emergency system and of the manufacturer of the device that are the most common.
Control Panel - device - Graphics Manager - note the brand and complete model
your video card - double - tab of the driver - write version information. Now, click on update
Driver (this can do nothing as MS is far behind the certification of drivers) - then right-click.
Uninstall - REBOOT it will refresh the driver stack.Repeat this for network - card (NIC), Wifi network, sound, mouse, and keyboard if 3rd party
with their own software and drivers and all other main drivers that you have.Now in the system manufacturer (Dell, HP, Toshiba as examples) site (in a restaurant), peripheral
Site of the manufacturer (Realtek, Intel, Nvidia, ATI, for example) and get their latest versions. (Look for
BIOS, Chipset and software updates on the site of the manufacturer of the system here.)Download - SAVE - go to where you put them - right click - RUN AD ADMIN - REBOOT after
each installation.Always check in the Device Manager - drivers tab to be sure the version you actually install
presents itself. This is because some restore drivers before the most recent is installed (sound card drivers
in particular that) so to install a driver - reboot - check that it is installed and repeat as
necessary.Repeat to the manufacturers - BTW in the DO NOT RUN THEIR SCANNER device - check
manually by model.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers under Windows 7 (updated drivers manually using the methods above
It is preferable to ensure that the latest drivers from the manufacturer of system and device manufacturers are located)
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlIf you update the drivers manually, then it's a good idea to disable the facilities of driver under Windows
Updates, that leaves about Windows updates but it will not install the drivers that will be generally
older and cause problems. If updates offers a new driver and then HIDE it (right click on it), then
get new manually if you wish.How to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx===========================================
Refer to these discussions because many more excellent advice however don't forget to check your antivirus
programs, the main drivers and BIOS update and also solve the problems with the cleanboot method
first.Problems with the overall speed of the system and performance
http://support.Microsoft.com/GP/slow_windows_performance/en-usPerformance and Maintenance Tips
http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/19e5d6c3-BF07-49ac-a2fa-6718c988f125Explorer Windows stopped working
http://social.answers.Microsoft.com/forums/en-us/w7performance/thread/6ab02526-5071-4DCC-895F-d90202bad8b3I hope this helps.
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
Maybe you are looking for
-
Firefox 16.0 Windows Vista 32-bit. Just go to FF16.0. When I try to change the text on my personal Blog, I get the text unreadable because they overlap ~ 8 times. Another site picture icons were repeated 8 times for each icon, as well as each downloa
-
I have the money on an old apple ID
I need to transfer this money on my new apple ID?
-
Run a number of re-entering VI
Hello I am creating a VI that will run at the same time any number of re-entering the Subvi. After looking at lots of examples, one which better reproduces the behavior I want is located at \examples\general\Reentrant Panels.llb\Reentrant Panels.vi.
-
Want to 700-515xt CTO: Support for 1440 p HD 4600 graphics card
I am running a 1080 p with an integrated graphics Intel HD Graphics 4600 a HDMI monitor and DVD I out with 10 64-bit Windows. I want to start a monitor 1440 p with the 4600. I do not find the specifications for the 4600 and so do not know if can ma
-
I continue to receive messages that COREFOUNDATION.dll is missing, how can I fix?
I continue to receive messages that COREFOUNDATION.dll is missing, how can I fix?