ISE pass 1.3 (876) in ISE 1.4 patch 7 or newer

Similar Questions

• CWA ISE 1.2 Patch 7 possible comments bug

  Just upgraded an ISE implementation to patch 7 and discovered the patch broke comments CWA portal the wireless. I have not tested the wired CWA but wireless is down.

  In summary, the redirect works fine, but when you enter valid credentials comments nothing happens including no newspaper in the ISE. If you enter the credentials that do not exist in the comments group, you get an authentication failure and the corresponding journal. As soon as I drove back to patch 6 everything worked again.

  If TAC see what engineers do not hesitate to continue - I would connect a case but the kit is NFR and I can't be bothered going through the process of logging to a job on the NFR kit.

  Please visit CSCuo16503

• ISE v1.2 patch PSN 5 down, deleted endpoint identity

  Please refer to the diagram. I'll make it simple and clear.

  Patch version 1.2 of ISE 5

  3xPOL (2xVirtual devices)

  1 LUN

  1 Admin

  Since Janauray the 8th we have problems with ISE. problem encounter were end of endpoint profiling devices like (Cisco 1140 AP) but the devices is a portable Motorola running Windows CE. Also the mac address of Motorola deleted endpoint identity, every 4 to 6 hours, and we need to put the mac address manually to start the authentication to work.

  We open a cisco with TAC. and TAC advice there is a bug in the software and must be upgraded to patch 17 or be upgraded to 1.4 as EHT it more stable than version 2.

  a few days later after one of the node POL3 (in the language of cisco PSN) went down. and one of our clinets SSID WiFi lost the connection that they were unable to authenticate (security WLC are on POL3 with ISE group created AD HOC Network devices with filtering MAC.) to solve the problem, we change the WLC AAA to POL1 (PSN) security to make it work. given that his work.

  later the next day an another POL2 (up/down beat) other clients of SSID (DATA) are starting to declare connection drop. change us again the WLC AAA authentication ip in the direction to POL1 since his works very well.

  now on 3 only 1 POL's work and three SSIDS end clinet is authenciated by the ip address of this POL.

  We arrived at cisco help, they looked in this and said POL node are not syn. so EHT needs a reboot to fix this. US management decided if this requires a reboot to fix theye why do not upgrade us to version 1.4 EHT. Cisco TAC mention upgrade can take up to 3 to 4 hours, or maybe more depends on the server. Now we want to go to upgrade but our network structure is complex, we do not want to lose the ise for 3 to 4 hours. We are a hospital and all verification devices/doctor patients computers/handheld devices/records are authenticated through ISE. We using ISE mainly for the wireless.

  Now, it's the background story. now, I have a question can reload us the POL nodes 1 by 1 to resolve this problem. I also noticed there is another work around, we had another node ISE from another hospital of trust in our data center. It is a virtual appliance (ise - psn.web.com) in our controller ip address SSID (WLC) one of our leading hospitals of authentication setting two AAA is POL1 and next is the ip address of the ISE - PSN. WEB.COM if we recharge our ise and wlc, we note the ip address of the ISE - PSN. WEB.COM will be this keep the SSID client remains connected.

  Please let know us that we are in a desperate situation where we need advice to minumis downtime of our patient critical application that are connected wirelessly.

  Hi there and sorry you are in such a crappy situation. It's no funny!

  To answer your questions:

  #1. I would certainly recommend the upgrade to a later version of ISE or at least get your current version on the last patch!

  #2. Yes, you can reload the Ssnp one at a time with zero and without interruption of service. Your WLC detects that your first PSN is down and then move to the second that is configured under the SSID > AAA servers. It is very important that your PSN is in a node group. This way if the PSN-1 goes down, none of the sessions that have been in the middle of the AAA process will get absorbed by another node in node group. If the PSN is not in a group of clients node trying to authenticate to the network at the time of charging will have to start again.

  #3. Once that clients are authenticated and authorized their rail traffic is no longer the PSN. So, reload the PSN will not affect clients that are already on the network. However, if a customer needs to re-auth (in due to inactivity, slowed down or re-auth timer) then a job THAT PSN is necessary, otherwise the AAA session will fail.

  #4. Certainly, you can set up a third NHPS under your SSID and use your PSN which is in another hospital. As long as this node is located in the same deployment of ISE and is synchronized with the PAN then you should be good to go. You can quickly test it by creating a temporary SSID > do as PSN its main Radius Server > test it with a test computer.

  I hope this helps!

  Thank you for evaluating useful messages!

• ISE 1.2 patch 3 - lag default portal Sponsor changed to non-existent ECT

  Hello world

  We applied Microsoft3 to our ISE 1.2 cluster and after the upgrade all the sponsors accounts (outwardly autenticated on Active Directory) are now GMT + 01:00 Europe/ECT as time zone default. So the guest account have the same time zone time and invited the authentication will fail.

  It's the mistake of ise - console.log:

  Comments:-com.cisco.cpm.guest.exceptions.PortalUserException: java.lang.IllegalArgumentException: zone of datetime id "ECT" is not recognized

  Comments:-to com.cisco.cpm.guest.edf.GuestUserAdaptor.isAcctValid(GuestUserAdaptor.java:489)

  I checked the interface of administration and documentation 1.2 but could find no default setting for users of sponsor zone

  Time zone for the 3315 is THIS:

  clock timezone THIS

  One solution is to update its zone on sponsor Portal setting has each user of sponsor, but it is impratical.

  Doesn't have all the known world the same problem?

  Kind regards

  Hello

  You hit CSCuj91050 bug I guess. This will be fixed in patch 4 I think, but for now, you can go back to patch 2.

• Unable to pass user id and password in the URL to open the new form

  We have installed a version of updating of forms 11g and I find that the following code does not work as expected.  Instead of perfectly open the dropper_assign form, we receive the standard name of username/password login prompt / database independently passing credentials in the URL.  If I get the password exactly as it shows in the resulting url then connects the form and the form opens as expected.  Any ideas would be greatly appreciated.

  Code:

  WEB. SHOW_DOCUMENT ("JavaScript: void (window.open ("http://'|| "))") ip_port | "/ forms/frmservlet? pageTitle = dropper transfer & config = TTMSMENU & form = dropper_assign & userid ='| user | » /'|| GET_APPLICATION_PROPERTY (PASSWORD). » @' || : overall. (("DB_Instance |'", "", "resizable = Yes, location = no, Toolbar = no, MenuBar = no, Status = no,")); self. Close () ',' _blank');

  Resulting URL:

  http://9.35.32.204:9001/Forms/frmservlet? config = TTMSMENU & Form = dropper_assign & userid=SSBUECHL/My123pw@FCTEST

  The real problem comes to set these two variables formsweb.cfg in my ttmsmenu Setup:

  UserID = @DATABASEID

  LOGON_SCREEN = YES

  In Forms 10 G, this works to pre-populate the database id in the field of database on the login screen.  In Forms 11 G, remove the logon_screen variable solves the transmission of identification information of the URL.  Delete the userid variable eliminates a bad initial connection attempt.

  Thanks for the help.

• Impossible to pass guard Office suspended on the verification of the addons with new version 3.6,

  I want to improve every time I have the same problem. A normal level is normal, but then the new version will check the addons for compatibility and there it does'nt go further.

  Also, when I first delete the entire installation of firefox and you want to install, I get the same problem

  I used version 3 for years, as whenever I tried an update, it crashes. Even with 9. So I had to always go back and reinstall 3, where everything would be fine. 9 works on my laptop with Vista and the new feature I wanted was synchronization, to synchronize bookmarks. This idea of love. But on my desktop with XP, could not for the life of me get Firefox works with any version past 3.

  Here's the solution that worked for me:

     opened the version that worked, and saved bookmarks to USB drive. That's the main thing I wanted in the new version.
     uninstalled FF
     manually deleted all files in FF and Mozilla folders on the hard drive, including any folder named "mozilla" or "firefox"
     edited the registry (read about how to do this properly elsewhere) and manually did a search for and removed every single instance of "mozilla" and "firefox" that existed on the computer. Made sure I did search from the top of the registry tree
     rebooted
     installed firefox 9
     imported bookmarks from USB drive
  

  everything works fine now! Years of updates does not work and a clean registry does the job.

• Items are passed at the opening of vi with f3 patch

  Many elements on the front panel, when I open the vi with the LabVIEW 2009 f3 patch installed.  Is it possible to prevent this?  Otherwise, there are a lot of enhancements that will be needed if things line up again...

  You can set the font used in the tools, Options, menu environment.  It will allow you to change the font and it will write the setting to the LabVIEW.ini file.  Set the font to Tahoma as if it was XP instead of Segoe as if it was in Vista.  Search the forums for the fonts in the application, the police system, .ini, XP, Vista, as keywords and you should find more discussions mentioning these issues.

• ISE 2.0 authorization number (patch 1)

  I'm running into a bit of a strange problem with ISE 2.0 (patch 1).  I have a laptop Win 7 passing authC/authZ, get an IP address, but cannot access internal or external resources.  It uses 802. 1 x with EAP - TLS with machine and user of AD certs.  With this question, I'll have a MAR, but TAC addresses this issue.

  I just can't understand how the device can get an IP address, but not access anything on the network.  The laptop can do a release/renew the IP address, so it becomes somewhere on the network.

  DRM for ideas.

  -Dan

  Looks like a dhcp snooping/analysis of device issue, the sess auth does not know the ip address of your windows pc and then the ACL is not applied. You can check with 'show ip access-list interface x/x '. Can you do a 'show ip analysis device int x/x' and see if the ip of the device shows as active? Also have you configured the settings recommended in the switch using the configuration of the switch guide universal trustsec?

• Cisco ISE Patch 1.3 6 procedure

  Hi team,

  Please help me with the installation of fix on Cisco ISE version 1.3.0.876. I intend to patch our ISE with HA Set - up for patch 6. There also a way to upgrade? I read that you must install the hotfix on the primary node, then the secondary node automatically update to patch 6. Which command will work for me to check that the secondary image is upgraded to patch 6. Also, how much time it take to restart the application.

  Thanks in advance!

  Kind regards

  Mady

  Hi Mady-

  You can perform the installation, restore and check the status of the patch directly from the graphical interface on the head node to Admin. You can reference to ISE 1.3 Administrator's Guide:

  Install the Patch:

  http://www.Cisco.com/c/en/us/TD/docs/security/ISE/1-3/admin_guide/b_ise_admin_guide_13/b_ise_admin_guide_sample_chapter_0101.html#ID202

  Check the status of the patch:

  http://www.Cisco.com/c/en/us/TD/docs/security/ISE/1-3/admin_guide/b_ise_admin_guide_13/b_ise_admin_guide_sample_chapter_0101.html#ID325

  I hope this helps even if end :)

  Thank you for evaluating useful messages!

• Cisco ISE and the fast user switching

  Greetings,

  In our deployment, we are interested in using the "fast user switching" which lies in the functionality of Windows.   After searching for a while, I see that the native Windows supplicant is not compatible with the fast user switching.   It does not appear that Anyconnect is either.   Can you please inform me as to what suppluicant, I need research to enable the functionality of Switchign user?

  We currently use ISE 1.2 Patch 4.

  Thank you for any assistance.

  David

  Cisco EHT NAC Agent does not support Windows fast user change when you use the native supplicant. This is because there is not clearly the older user disconnecting. When a new user is sent, the Agent is hung on the ID process and the old user session and therefore a new posture cannot take place. According to Microsoft Security policy, it is recommended to disable the fast user switching.

  Source:

  http://www.Cisco.com/en/us/docs/security/ISE/1.2/user_guide/ise_pos_pol.html

• Cisco ISE machine has no machine authentication

  Hey, since we migrated to ISE 1.2 patch 7 we have problems with our company SSID.

  We have a rule that essentially says:

  The user is a domain user.

  The machine is in the field.

  But for some reason, some workstations are is denied by this:

  ISE 24423 was not able to confirm the previous machine successfully authentication of user in Active Directory

  I was wondering if I could force a sync?

  Hmm, you when you restart the machine you should see an entry of authentication which starts by "host /" Let's try this:

  1 uncheck the box 'Remove' repeated successful authentications and the "suppress abnormal customers'

  2. wait 10 minutes

  3. restart the computer and try again and let us know what happens

• Authentication of the machine does not work after the night of workplace surveillance ovr - ISE - 1.1.1

  I'm running an ISE 1.1.1 patch 2 and authetntication machine Windows XP using PEAP authentication with authentication computer and user.

  The issue is that when a machine is powered on fine machine authentication processes and the user authentication is successful. The problem is that, after that the machine is connected to the left and left unattended for may hours I am bounced in a guest VLAN - ISE newspapers say that they can validate is no longer the machine has been authenticated via AD. If the user reboots the computer, he is well again.

  Are there timers in AD or the machine that are hot flushes the status of RADIUS: WasMachineAuthenticated? Can someone tell me if there is a recommended configuration when the machine authentication is maintained throughout a work day or night?

  Hello rcianci.

  You experience this problem because of your authorization rule "WasMachineAuthenticated." This process (aka MAR - Machine access restrictions) occurs only when a computer is restarted or powered. Once the expiration of the timer to MAR the machine authentication fails until it is restarted again.

  Here are two ways you can try to tackle this problem:

  1. I used MAR in the past and:

  a. set the timer for 168 hours (1 week)

  b. educated users that they must restart their machines per week

  It worked 'OK' but it's still irritating to the end users. It can also cause problems if you do that for cable and because the MAC address will change and ISE/ACS will not see the new authenticated as mac address, which requires the user to perform another reboot

  2. a better way to be rid of MAR all together. If you want to keep things simple, you can just use PEAP machine based authentication using the credentials of the machine. It's not always ideal, but if your ad is correctly locked where only certain users can join computer to a domain then you should be good to go. However, if you want to continue to use the machine + user you will need to look at something a little more complex such as EAP-chaining.

  I hope that this help... Let me know if you have any other questions

  Thanks for the note!

• PC profiled as a phone by ISE 1.4

  Hello

  I see that attached to the Cisco phones PC profiled by ISE 1.4 (patch 3) as Cisco phones. When first attached to the n (Cisco 6880 - last worm 15.2) the phone is emerging as a "Cisco-IP-Phone-7911" correctly and the PC is 802. 1 x authenticated ok and profiled as "Microsoft-workstation.

  In the minute the PC varies "Microsoft-Desktop" to "Cisco-IP-Phone-7911"in the list of endpoint ISE."

  When I opened the PC in the endpoint list, I see that he "inherited" details cdp of the phone. When I disconnect and reconnect the phone/PC, they all have two get profiled by ISE that phones - the n is configured to access Multi field (a device authorized in both voice and data) then the switchport is off because of a security breach.

  To work around this problem, I have disabled cdp on the n and active lldp. The phone is now emerging as "Cisco-IP-Phone" (Cisco-IP-Phone-7911 profile requires cdp) and the PC is profiled as "Microsoft-workstation.

  Is this a bug ISE or IOS? I had this problem with all available versions of the track 15.2 for the 6880. I am aware of the bugs CSCuu97659 and CSCuu94127 but these thought related to ISE 1.3 and earlier versions

  Thank you
  Andy

  Hi Andre, I think you're hit these bugs... and add to the mixture CSCuu76087 :)

• ISE 1.2.1 support for Yosemite?

  Hello everyone, just curious. I see in the release notes for ISE 1.2.X that support for Mac OS 10.10 (Yosemite) was available via patch 12 on the train ISE1.2.0 of the code. That said, I see nothing in the release notes indicating support for Yosemite for any patches for ISE1.2.1, the latter being patch 3 released 1 week after ISE 1.2.0 patch 12. Please can someone tell if Yosemite is based in fact on 1.2.1 with patch 3?

  Thank you very much in advance for your help

  Jeff

  Jeff,

  OS X 10.10 is supported in ISE 1.2 p11, 1.2.1 p2 and 1.3.

  Patch 12 for 1,2 and 3 Patch 1.2.1 fix other issues for OS X 10.10, and I recommend you to update on the latest patches for these fixes.

  Here is the entry in the Release Notes detailing the fix for 10.10 to 1.2 p 12:

  

  MacOsXAgent versrion 4.9.5.3 should be used and MacOsXSPWizard 1.0.0.30

  

  Note that the description of these files refer to ISE 1.2 Patch 11/12, ISE 1.3 release and above.  ISE 1.2.1 is not mentioned, but follows the calendar bug fix and version 1.2, with an adjustment.

  Patch 1.2 10 = 1.2.1 hotfix 1

  Please rate useful messages and mark this question as answered if, in fact, does that answer your question.  Otherwise, feel free to post additional questions.

  Charles Moreton

• ISE foreign CWA / deployment WLC - missing user of anchor names

  I'm not sure if this belongs to the section mobility or security - I'll just give it a try here.
  I've set up wireless access visitor with Cisco ISE 1.3 (patch 2) and a stranger WLC / anchor of deployment (7.6.130.0).
  So far almost everything works fine - but I probably have a problem with logging Cisco ISE.

  In exploitation forest 'authentications Live', I see the authentication successful, but the identity of the column, it shows just the MAC address of endpoint.
  If navigation to the identity store of endpoint endpoint of comments is in the right group (guestendpoints) and when you look at the details of the endpoint, I can see the "portalusername" who created the user.

  If I click on endpoints active view (see attachment), I can see all active clients (Authz profile "PermitAccess"). I guess the user name of the client must be filled out there as well, no?

  endpoint_view.PNG

  

  Someone has an idea what is the cause for this? Or is the normal behavior?

  My rules of authentication are:
  If "wireless_mab" and "RADIUS: Called-Station-ID ENDS WITH comments-SSID" then use "endpoints internal" and continue if "user not found".

  My authorization rules are:
  1.) if GuestEndpoints AND (Wireless_MAB AND RADIUS: Called-Station-ID ENDS_WITH Guest SSID) then PermitAccess
  2.) if (Wireless_MAB AND RADIUS: Called-Station-ID ENDS_WITH Guest SSID) then GUEST_WEBAUTH
  The profile GUEST_WEBAUTH Authz defined the CWA and preauthentication ACL for the WLC

  The WLC I just configured the WLC foreign with the RADIUS (ISE) server and active authentication MAC the SSID.
  All parameters such as aaa-override and RADIUS of the NAC are defined. The defined RADIUS is set on "settler" to comply with the ISE

  According to my experience, this is the expected behavior.  The new workflow for the use case of comments starting at the point 1.3 of the ISE typically includes registration of endpoint, you're.  Your strategy for authz for post-portail of authentication (after the certificate of authenticity) needs the MAC address to use as the identity for permissions invited, not the guest credentials used on the portal.

  That being said, I would like to be able to see the username of the user portal whenever a registered endpoint point authenticates (until it is served using endpoint political purges, of course).

  Tim