LAPAC1350PRO limited to less than 5 MB
I have four cluster of WAP. None allow a speed greater than 5 MB. Direct connection to the switch allows to 150 MB. The radio is set to n. Is there a setting in the configuration to limit the speed.
Yes, it's the pro version. This question drove me nuts. This is the only solution that I found.
I went to QoS and access control
Global settings
Activated
Selected for each radio and WAP
Mapping ACL and QoS
Activated
Bandwidth down to 4294967295
Bandwidth up to 4294967295
To be clear, I had none of these configured settings and all customers reserved modes 5 MB.
Tags: Linksys Products
Similar Questions
-
Windows 7 adjustable threshold less than 100% of the battery charge?
Hello.
I have a Clevo P170HMx which is a cell phone game impressive.
Probably the only thing I don't like is that my battery is always 100%. I used my laptop plugged into an electrical outlet.
and knowing that to have my battery to 100% and always load will destroy the battery life.
My previous laptop was an IBM Thinkpad, and it had a maximize battery gauge allows you to define the allowed charge batery
threshold. I got this game to start the load to 15% and stop loading at 20%. I had this same battery from the time of purchase
until 4 years later, I got my new laptop, the battery remained in excellent condition with load capacity full not escape
as do other batteries when they stay at 100% and reload constantly.
Is it possible on Windows 7 pro to change the threshold of battery charge to stop less than 100% load to save battery life
life? Or is it Windows software available for download that will make this recommended?
If Windows 7 is not able to do this, I would say something in an update service pack or the next version of Windows.
Thanks a lot for your help.
See you soon...
Hello
In normal circumstances as soon as the lithium-ion battery is full, a properly functioning charger will stop the charge and will only engage when the battery voltage drops to a low level. Most of the users do not remove AC power, and this practice is safe.
The latest Lithium-ion batterires have a limited number of Discharg/charge cycles.
You can create a detailed report on the State of the battery to double check the battery status.
1. go to Start / all programs / Accessories. Click on the command prompt and select run as administrator.
2 in the command prompt window, copy / paste the following command.
powercfg-energy-output %userprofile%\desktop\energy-report.html
Press ENTER.
Wait for the command to complete (usually about 2 minutes).
This create a file named energy - report.html and place it on your desktop.
3 go to your desktop and double-click the file to open.
Scroll to the bottom for the battery: battery information section.
You will see:
Rated xxxxx
Xxxxx full last Charge
(Where xxxxx is a number)
4 to calculate the amount of full Charge capacity left in the battery split the value of the last Charge full rated capacity and multiply by 100.
For this example , use the following numbers.
Nominal capacity 4400
Last full 2937
Calculator enter 2937 and divide by 4400.
Multiply the multipliez le resultat result by 100 , then press =.
The result will be 66,75
This means you have 66,75% of the nominal capacity of the battery.
Tell us what you find.
Concerning
-
Songs to jump himself and backup battery less than before
Hello Sir/Madam,
I'm David. I have an ipod touch 6th generation, I've updated to firmware ios 10.0.2. I am confronted with these questions when I updated to ios 10 songs automatically you click previous track when I haven't touched and backup battery lasts 1 day before I used to get more than 2 days. He could use someone to help me get rid of these problems I face.
Try:
-Reset the device iOS. Nothing will be lost
Device iOS Reset: Hold down the On / Off button and the Home button at the same time for to
ten seconds, until the Apple logo appears.
Unsync/delete all the music and Resync
To remove all music go to settings > general > use > storage > storage management > music > tap Edit in the top-right, then press the sign less than all music
-Reset all settings
Go to settings > general > Reset and tap reset all settings.
All your preferences and settings are reset. Information (such as your contacts and calendars) and media (such as songs and videos) are not affected.
-Restore from backup. See:
Restore your device from an iCloud or iTunes backup - Apple Support
https://support.Apple.com/en-us/HT204184
-Restore factory settings/new iOS device.
If still problem, make an appointment at an Apple store Genius Bar because it appears that you have a hardware problem or there is a bug in iOS.
Shop Apple Store - Genius Bar
-
How to return the highest value in a column of numbers less than a given number
I am a beginner using formulas in number. I have an inventory in a Numbers spreadsheet (v3.6.2). Inventory numbers are in a column. I need to view the last number used or the highest number less than a given value. In my case, it is 9000.
I can put a cell to return MAX and it's cool, but I need to know the number < 9000, MAX.
Hi JS.
SEARCH is your friend here. One of the properties of the LOOKUP function is that it accepts a 'close-match', which is defined as the largest value less than or equal to the search value.
Formulas:
A2: LOOKUP (8999.9999999, D)
B2: LOOKUP(9000,D)
C2: MAX (D)
Kind regards
Barry
-
Latest firefox does not an option in youtube for any video affecting less than 360 p. When I use IE, it gives you all the options of configuration from 144 p. Other sites using firefox it is choice in the video settings of all yet EI did not. My last version of firefox was ok but now this new version gives very little choice in the matter. What can be done to solve this problem.
Hello, you can try to install the adobe flash plugin: install the Flash plugin to display videos, animations and games
-
I bought the IPad Pro 128 GB on 3.29.2016. I used it for less than a week. It charged when I first opened it from 67% to 100%. 9.3.1 update. After about 5-6 days, the battery is down to 1%, and now it will not load. I have reset to factory settings and it still doesn't load. There's just 1%. Help, please.
Thank you
Katie
It is under warranty. Suggests taking it for an Exchange.
-
Someone commented ago about 9 weeks for my site to load very slowly. I tried and had no problem.
But a few days ago, I realized that the first call (after rebooting the system) in Firefox 7, 8 and 9 of Firefox Firefox takes 10 + seconds (white screen) while other browsers have need of about 1 second. After the initial call each page loads faster than in other browsers.
Without content management system, I got the same results. In simply removing things from the grid of my stylesheet, pages loading less than a second. I tried other grids http://cssgrid.net/, http://www.webdesignerwall.com/demo/simpler-grid/940grid.html , but had the same number.
A identify the extension that is causing the problem in your case?
He is always unpredictable, how the extensions behave with a new version and in case of problems you can contact the developer of the extension to inform him about the problems.
-
Tecra A11 - less than 10 ips in Skyrim on
Hello
I have a Tecra A11 i7 which came with a wiped HARD drive
I installed win 7 pro and the drivers from the Toshiba site, including the pilot Intel Turbo Boost Technology.Even with all the settings set to low temperatures, vid Skyrim runs only less than 10 frames per second.
I upgraded 4-8gig ram, but this did not help.
The GPU is Intel, so I can't use Geforce experience.I have a Dell Vostro V131 i5 which takes place to better Skyrim.
But the screen is smaller and i/o ports are 90% of dead, so I'd rather use the Toshiba.There are 4 "unknown devices" in Device Manager, but none of them look relevant.
Does anyone have any ideas?
Thank you
To be honest, I have no reasonable explanation because I don't have this video game and can not test it on my Tecra A11 - 19M.
In my opinion this Tecra is typical business very bad for the games and the machine for office work.
It does not offer good graphics performance and it is not the best for gaming.I use it for daily activities and games use different model Satellite P with nvidia GPU.
-
I connect to online courses. I click on the link to a PDF on the site. It gives the message it is downloading, then stops. With less than 2.0 MB PDF files load, but nothing more.
No chance that your school uses Blackboard / WebCT?
If so, Firefox 4.0 has not been certified as being compatible with this software.See this page in Blackboard KB to see which version of Firefox is certified for the version of Blackboard Learning System Vista or THIS used in your school.
http://KB.Blackboard.com/pages/ViewPage.action?PageID=45581177 -
My son uses his laptop computer HP15 home to his office, rarely transporting. He never gave it and a sweet user.
The left hinge seems to be broken / defective, and separates the window. For now, we are all leaving the screen open all the time, but it's a little awkward and the problem is certainly on a laptop less than 2 years old.
Looking at the forum, it looks like a common problem.
We are fans of HP in general, so I hope that this problem can be solved.
Help, please.
-Steve
Hooray!
HP solved the problem free of charge, including shipping in both directions and repair.
It took ten days in total, and we used the laptop without a problem for about 10 days more.
It seems that the hinges for laptop and the display case were entirely replaced, and no data has been lost.
My son is thrilled to have his laptop in return, and to my eyes, HP just went through.
I wouldn't hesitate to buy another HP product, although I confess in the hope that:
(1) HP manufacuring no longer uses defective parts
(2) HP treats everyone with this problem of hinge with the same care
Thank you and HP support HP!
-Steve
-
How to create a formula to ask if something is both greater AND less than a range
Don't know how to ask the question, but here's what I want to do.
In a formula, I need an 'if' statement asking us:
IF "cell id" is greater than "$ 100" and less than "$ 200", IF - TRUE, IF - FALSE.
I don't see how the question of both the code < and=""> in this formula. I tried the instruction AND within the formula, but getting syntax errors.
Hope the question makes sense, thank you.
Hi Dwegs,
It is a way
IF (AND (A2 > 100, A2<>
-
I bought an iphone 5 c less than 2 months ago, and even if I don't use a lot of storage, I still almost nothing GB, what it can be?
Apps, music, images, even the contacts you add etc - all of these things take a valuable storage capacity on your phone.
Your backup device, delete it and then restore from the backup, maybe this will help free up space.
Use iTunes to restore the iPhone, iPad or iPod to factory settings - Apple Support.
-
Satellite P100 - 324 BIOS reports less than real memory installed, why?
I have a P100-324 Satellite which I installed 4 GB of memory.
Memory is a Kingston KVR667D2S5 / 2G, so I installed 2 of them.
I've updated the BIOS, but still when I press F2 to access the configuration
I find that the less than 4 GB installed memory. It makes account
3070 MB. When using windows the systeminfo program reports 4096 MB RAM.
However, System properties, it shows 3.0 GB and that is because
It is 32-bit windows xp mce. I ran live fedora 7 x 64 and he reports only 3 GB as the bios.
Why? Is there a way to fix that.Please look here, here's your answer:
http://support.toshiba-tro.de/KB0/TSB7601WE0007R01.htm
Lex
-
Select start measurment only if the temperature is less than 26 ° C for 10 seconds
Hello
I have a program for a measure of viscosity/temperature use DasyLab 12
I burn my brain to try to activate the measurment only if the temperature is less than 26 ° C for 10 seconds.
Click on 'Start', then control the temperature, if the temperature stay below 26 ° C, for 10 sec then allow to click the button "start measurment.
If this isn't the case, restart the control.
Thanks in advance!
Ivan
Simply enter the channel number. If this string has a name, DASYLab will automatically replace the figure.
-
Hello
I've created a dll com in VC ++ using performance counters/timers to less than a millisecond.
This is useful when you send a message to very high speed. (say 10 or more)
This is done by the dll.
When I use CVI to create a user interface, this dll runs at a fixed rate of 1ms.
This slows down the application.
I tried to use the same dll with VC ++ host and it works well.
I need to check the registry setting to see if the useDefaultTimer is set to false or TRUE.
(I'm not near the development PC) However, by default, it should be FALSE and I have no fidle with it.
Veuileez post any suggestions you might have.
Thank you!
This problem is now solved for me.
Just the highest thread priority in the dll.
Thank you if you had the answer.
Maybe you are looking for
-
How to uninstall a pirated version and load a good version of your site.
I thought I was on an official site of Mozilla/Firefox, but apparently I wasn't. The FF I loaded immediately disabled context menu. Each second counted adds popping up everywhere. As soon as I got rid of them, they reappear. It seemed that program ha
-
Click on a .pdf link does not open the .pdf file, it opens a SAVE DIALOG box
Recently, when I click on a link to .pdf file I'm not able to open the file in an adobe reader or a FIREFOX Web page or open it using the full program from adobe. Instead, it opens a dialog box SAVE asking me to save it on my hard drive. I don't know
-
Toshiba NB205 cannot Acess recovery Partition
I have visited before, but I can't do it again. I tried holding 0 and F8 but nothing works. Here's something I posted elsewhere on my problem.NOTE: I need to know what caused the problem, I just need to get into the hidden restore partition. Hello. I
-
Ask for password at startup pc?
Given that I uninstalled avg and install essentials microsoft my firewall is to stay. But I still have this problem. When I turn on pc there is a box just asking admins name and password, but I just click ok, then he continues to open the office. Thi
-
Error code 80070490 Windows update failure
I had to restart my computer to factory due to a problem. My computer works fine, except for one little problem... I can not get windows to date. I keep getting the "updates have been incorrectly configured, returning from changes. It happens that th