Lesson 4-2 homework: howto correctly complete the loop of acceptAndOpen()?

Similar Questions

• complete the loop and get data

  I need to acquire the acquisition values of data every x seconds. Waiting in the loop of data acquisition is defined so that the next N samples are acquired after x seconds. Pressing stop the loop of consumer DAQ stops after the sec x which is connected to the wait function.

  1. how to stop the inner loop immediately when you press a stop?

  I also write acquired samples after doing some calculations on the samples.

  1. plan of sample of the queue to file consumer loop. Is there any other recommendations such as drop loop is not without samples? How many data can an expectation of the queue?

  Thank you.

  sonotk,

  You've missed the point. Rather than having a 5000 milliseconds of wait, use an expectation of 100 ms and count the number of times that you have been waiting for 100 ms.  When the count reaches 50, sample and start the count again.

  The counter is just in the shift register containing an integer. Inside the while loop you have a box structure. Test the shift count register to see if it is 50. If set to True, use the real case of the structure of the case. Inside, it's all in your loop except waiting and the logic of the judgment. In the case of false, you add 1 to the shift register and wait 100 ms.

  Looking at your picture code once again, it seems that the shift with TempData and VoltData regsiters are not necessary because you never use the data previous iteration on the left side.

  Ranjeet,

  Make a simple VI with two loops and some expectations.  Run with execution highlighting market to see what is happening.  It is a good learning tool.

  Lynn

• The program I use is called Defraggler is a simplified version of windows Disk Defragmenter. It is not defragment my disk correctly. It is said that it has completed the defrag but it's still 23% defragmented files defragmentation

  The program that I use is called Defraggler, it was created by piriform LTD and it is a simplified version of windows Disk Defragmenter. It is not defragment my disk correctly. It is said that it has completed the defrag but it's still 23% defragmented files defragmentation. I pressed defrag again and again but he still took no action and said always full defragmentation when clearly there is no. I myself had a look at the options and settings and it should properly according to them. Any help will be kind of you. Thank you.

  http://Forum.Piriform.com/index.php?s=6f56df458b93b49ff84c76f6fcd13a05&ShowForum=19

  Kindly repost of Piriform Defraggler forums for help with their programs.

  http://docs.Piriform.com/Defraggler

  And read the Defraggler troubleshooting, info etc. at the link above.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  http://www.SnapFiles.com/reviews/Auslogics-Disk-Defrag/adiskdefrag.html

  You might try the Disk Defrag at the link above instead of Defraggler.

  See you soon.

  Mick Murphy - Microsoft partner

• I want to change country in my account to complete the purchase of programs process correctly... The amendment does not

  I want to change country in my account to complete the purchase of programs process correctly...

  The amendment does not

  Please see the change of the country associated with your Adobe ID.

  To change the Adobe ID, you can check your Adobe ID account management

  Hope this will help you.

  Kind regards

  Hervé Khare

• Lesson 1-1 code is correct?

  Hi all.

  I just started watching a course and have finished all the chapters of lesson 1, no homework and quiz.

  So we in Lesson 1-1 example usage of lambda expressions (with my method createStudentsList() to fill the list):

  Students list < student > = createStudentsList();

  Double highestScore = 0.0;

  for (s student: students) {}

  If (s.getGradYear () == 2011) {}

  If (s.getScore () > highestScore) {}

  highestScore = s.getScore ();

  }

  }

  }

  It compiles and works.

  But the proposed changes by using lambda expressions does not work:

  Students list < student > = createStudentsList();

  Double highestScore = student

  filter (new predicate < student > () {})

  public boolean test (Student's t) {}

  return t.getGradYear () is 2011;

  }

  })

  .map (Mapper new student, < Double > () {})

  public Double extracted (student s) {}

  Return s.getScore ();

  }

  })

  . Max();

  saying "the filter method (new predicate < student > () {}) is undefined for the type List < student >" and "Mapper cannot be resolved to a type.

  Even the latest version of the code does not compile:

  Students list < student > = createStudentsList();

  highestScore = student

  filter (student s-> s.getGradYear () == 2011)

  .map (student s-> s.getScore ())

  . Max();

  with "syntax error, insert ';' to complete the statement" for the two statements of student.

  I managed to make it work with this approach:

  Students list < student > = createStudentsList();

  Double highestScoreL = student

  . Stream()

  filter (s-> s.getGradYear () == 2011)

  .mapToDouble (s-> s.getScore ())

  . Max()

  . getAsDouble();

  I do wrong or just missed sth sth important? Sorry for the question so long - it is because as pieces of code .

  BTW I use Eclipse March 4.5.0 and jdk1.8.0_51 if that matters.

  There is problem with your code. I fixed your code and it would be:

  Student s0 = new Student(2014, 685);

  Student s1 = new Student(2014, 675);

  Student s2 = new Student(2014, 635);

  Student s3 = new Student(2014, 985);

  List of students of = Arrays.asList (s0, s1, s2, s3);

  Stream studentStream;

  studentStream = students.stream ().

  filter (new predicate() {}

  @Override

  public boolean test (Student's t) {}

  return t.getGradYear () is 2014;

  }

  });

  Stream highestScoreStream = studentStream.map (new function() {}

  @Override

  public Double apply (student s) {}

  Return s.getScore ();

  }

  });

  HighScore = highestScoreStream.max of in option (new comparator() {}

  @Override

  public int compare (Double d1, d2 Double) {}

  Return d1.compareTo (d2);

  }

  });

  Double highestScore = highScore.get ();

  System.out.println (highestScore);

  Make sure and tell me if you don't get anything. This is the detailed code pre JDK8 average. Now you can write it as functional programming.

  and Yes... The video code is just for us to understand. It is not syntactically correct as map is not a FunctionalInterface in JDK8.

• Help! Lesson with 2 branches of locking on the Quiz results screen when the learner (branch or another) fails.

  I have a lesson CP6, which is essentially two parallel branches, with only the following slides in common:

  • A slide 'welcome. '
  • A slide where the learner chooses its branch
  • A "Congratulations!"  "Slide you completed the test.
  • A slide "you not answered the questions correctly.

  Once the learner chooses its branch, it is given a 5 question test.   If he fails the exam, he is taken to a short lesson, specific to the content tested in this branch.   When he finished the lesson, he is returned to the test to try again.  If it fails, come back to the lesson, then back to the review, etc.  until it passes.  (I put max '10' under 'Préférences Quiz' tent)   When he passes, he is taken to the "Congratulations" slide and the end of the lesson.

  I put the last question in each branch to go to slide Quiz results (success or failure), and I put the Quiz preferences to access the slide of "Congratulations" so passing and for the "you not answered the questions correctly" drag if the learner does not.

  That's how it is supposed to work anyway.  And that's how it worked until I made a change somewhere and he mucked things.

  What happens is instead:

  • Testing (both branches) learner outcomes Quiz and 'Congratulations' slide takes very well.
  • Lack of test (or another branch) brings the learner to Quiz results and then gets stuck there.    (In fact, if I click on the "Continue" button a second time on the QR slide, the lesson does not always advance but disappear all the graphics, that I put on this slide, which is weird and not at all useful.)

  Branching seems ok for me.   What Miss me?

  

  I know I have to improve and we will be soon, but not before this lesson must be published - which is, of course, yesterday.

  Help?  Anyone?

  Figured it out.  A "required" on the page "Quiz: settings" value "necessary Pass - the user must pass the quiz to continue."  Who kept the learner continued beyond the "results of the Quiz" slide and a loop to the didactic content and taking the quiz.

  I changed "Required" "Required – the user must take the quiz to continue."   The learner is able to loop back/reading/retest as many times as necessary in order to pass the test.  All right.

• VI considered non-executable runtime LV, correct in the development of LV

  My current problem is the following:

  On the same PC, with TestStand 4.0 and development of LabVIEW 8.5, I try to run a sequence with two adapters: 8.5 LV and LV DURATION 8.5 development.

  My sequence no call screw complete this call subVIs in a hierarchy (let's say 1500 screws are involved in a test sequence).

  The sequence works with the adapter of development, and with the runtime, I got an error like LabVIEW-18002: Vi not executable, broken, etc.

  Of course, when I open the VI in the development environment, everything is correct.

  I tested the two cards on the same PC, full hierarchy, including libraries provided with development of LV LV is in the same place.

  Due to the large amount of screws that I use, I can't guess LLB can be missing or inaccessible.

  Is there a way to investigate the cause, despite the fact that everything is correct under the development environment?

  Is it possible to indicate the LV runtime where it should search the LLBs or other dependencies that the development of LV seams to be able to find?

  Thanks in advance for your help,

  JJD

  Yes, it was a problem of subVIs sharing the same name (someone has copied and adapted some of the code).

  After cleaning of code and a compiled all mass is back to normal...

  Note: the problem appeared with LabVIEW and screw closed before running the sequence in both cases.

  Thanks for your help.

• Effect on correction of the CJC to use copper instead of type thermocouple extension cables

  Hello people. It is is a kind of "phenomenological" question, lumping together a bunch of real problems. Type of hope that someone had experience try this and can give me an advice.

  I'm looking to make measurements of temperature relatively high speed with very fine wire of type K or N thermocouples.

  I will be very many TC - about 75 in quantity and therefore will be, if it works well enough, wire the asymmetrical (I trading accuracy for amount in light of the SCB-two 68).

  My complete data acquisition system is:

  Computer PXI

  PXI-6225

  (Qty 2) SCB-68

  QUESTION 1: Any recommendations in the configuration of these two NRSE or GRSE? The device, I am close to (but not electrically in contact with) is completely without merit (experience of combustion). TC fine wire is indeed very thin, and their not armoured lengths will be about 12 ". There is no significant EMF/EMI around my experience. I will experiment but just wanted to know if anyone can rule something here...

  QUESTION 2:

  Important points:

  • I want to use type N for additional above K to my temperature range and also because that N-type are available in smaller caliber (0.003 ") and stability welded end to end.
  • Unfortunately, I n ' t has a bunch of N type connectors - if I have to use/buy the N type connectors this is a significant cost (see the stop).
  • My Setup has the TC in the physical location of 'groups' of 7. Given the asymmetric configuration, I have 7 anodes and 1 single "reason" for each "group" - for a set of 8 wires out of each "group".
  • I need to connect on the order of 80-wire in both SCB-68. I try to minimize the number of threads that I have to deal with.
  • Omega does not sell single conductor wire anode and cathode for the N-type as they do for K-type. They sell only duplex son.
  • Omega is also not sell armored bundles of type N, as they do in K-type
  • If I use type N TC and I use the real N type extension wire, it will have to be duplex (because of two previous points) - it's something like 80 PAIRS of wiring, with one of the sons of the cathode on most of the wires not used (because of the asymmetrical configuration).

  It seems that I must consider the following compromise:

  Use the TC type desired N and treat approximately 80 pairs of duplex wire extension of type N OR less desired TC type K and purchase grouped, shielded wiring to minimize the mess of wiring GOLD copper use extension (WHAT?)...

  Yes! Why can't I use the copper wire extension to the fine N TC of the cable type and connect to the TC with a kind of nonmetallic connector (like screws nylon) or solder? The attraction here is that I could use the signal wire 8 drivers together, to each of my TC 'groups '. This would reduce and clean my wiring and not need to buy all type N connectors (TC would be wired, no connector involved).

  It seems to me that I could simply set up the cold welding (CSF) on board the SCB-68 fixed to work on N-type. Copper wire would result of the SCB-68 the TC type N. No metal connectors would participate. Thusly, being only one junctions P/OMEGA-copper and copper/OMEGA-N to deal with the CCM. This sounds like it would be exactly the same as a N-type wiring directly into the SCB-68, except that there may be error between the temperature reading to the CJCS and the junction of alloy copper/OMEGA real. This won't be a significant error because the two locations will be very close in temperature.

  If this "mistake" of temperature becomes a concern I can mount a TC that is unique to the copper/TC junction and make my own corrections (I think...)

  Here is a little schematic text (without taking into account all shunt connections in the CSR circuits...):

  Any circuit anode/channel: SCB-68 Terminal-> extension copper-> (direct connection via the non-metallic connector) OMEGA-P of the N type TC

  Common ground circuit/channel: SCB-68 Terminal-> extension copper-> (direct connection via the non-metallic connector) OMEGA-N to the N type TC

  This idea implies that the circuit board within the SCB-68 has copper conductors, such as the addition of copper extension wire would not create an additional junction.

  Anyone tried this? Can someone offer me some ideas?

  THANK YOU in advance!

  -Dan

  ddml wrote:

  Henrik-

  Thanks for the very useful reply. Yes, I forgot to mention that the lengths of wire extension will be the order of 1 m, then resistance extension must be low, even if common ground is used as part of an arrangement of asymmetrical circuit.

  ...

  Here's my last logic!

  • If my experience shows that the single-ended NRSE GRSE arrangement response or "match" the differential response conservative, I will choose asymmetric for more sampling points.
  • Since I know the extension wire / TC to the ASE will be nearly isothermal with the CBS itself, I would like to use the extensions of copper and accept (and possibly correct?) the error based on the temperature. I would like to use threads, as this I need 7 + and 1 ground by grouping of 7 TC to my DUT (Recalling)-> http://www.newark.com/jsp/content/printCatalog.jsp?cat=c127&page=1199&display=zoom
  • If during the examination of the previous point, I find that copper extensions are NOT practical and I need to use tank extensions of TC-metal all the way, then I choose a TC type K on an N-type. The reason is that there are many more options for tanks, bundled extension cable type K (N-type is apparently a sort of new and not very popular). However if copper extensions are possible, then I'll use the TC type N, motivated by their superior high temperature oxidizing atmosphere stability and the fact that I can get them in a configuration welded end to end to 0.003 "caliber!

  If none of this logic seems faulty or unrealistic, I would appreciate it really more input! I don't know that it will be a lot of work!

  Thank you once again,

  -Dan

  Dan,

  I've marked the important phrase what you're actually doing is moving the CCM of the CBS for the TC/copper connection. Any difference in temperature will directly add to the error.

  However, don't try to save the copper with your approach to 7 + 1, ask IT for another 12 m Ethernetcable guys more and go with 7 * 2 + 1 pair of reserve and make the summary at or near the CBS. IF you need a differntial measument system later, you need to rebuild all connections. (And not just add a new cable for all conical fittings, it is the twisted pair that makes the magic Yes, same vor 1 m!) Remember that you are dealing with µV! And since you want to quick reads without filter a lot of way, do not try to save $10 to about 12 m of cable. Somehow I have the feeling that you try you anyway

• not enough memory to complete the operation

  I looked in the forums for "memory to complete operation" error and despite the advice that I found, the error always happens.

  I'm using LabVIEW 2012 to try to constantly monitor our system, recording temperature, power, etc. vs time (values obtained by acquisition of data USB-6008).  The data being saved to file, is every 60 seconds using a small table (no problem here).  Allocation of memory time/sleeves typical LabVIEW is about 180 MB (4 GB of RAM on computer).

  The issue that I feel is related to our wish to display these data on a chart for long periods of time.  The current iteration of the code works as follows.

  (1) we have 2 XY charts with 2 slots of each.

  (2) for each parcel, I'm initialization of clusters of berries of 2 100 000 (XY pairs) that are related to the shift registers.  I know it's bigger that can be displayed on a chart, but I am currently more concerned with reducing the number of data copies.

  (3) every 10th data point is added in the tables using one up Bundle/Unbundle element with a 'subset of table replace. "  In other words, there are about 8640 points per day. (One day is the shortest duration usually read)

  (4) for the two traces on a XY Chart, two groups are combined in a table (using the table to build).  I think that's my problem here.  Since every time I update the charts that LabVIEW must allocate memory for the 4 XY plots. (I'm correct here?)

  Decimating the additional data during research on several days will reduce the amount written in the plots.  However, this creates copies of data.  It is useful in this case?

  Instead of initializing 4 groups (1 for each plot) and combining in the tables later, it would be better to initialize the array of clusters of berries (2 lots per chart) and update the data by "index / unbundle / replace the subset of table / bundle replace table subset" series of operations?

  Nothing obviously bad jumps to my, but this could be why it works for days sometimes.  A few things to try:

  (1) the section where you overwrite the oldest 3600 data points and rotate tables has code to initialize a new table.  I propose this initialization outside the loop to make sure that only do you it once.  You could always simply replace the elements in the table with a value of NaN.

  (2) I would try to get rid of the build tables as you pointed out.  Initialize these berries outside the loop and replace components as appropriate.

  (3) build you tables of Irr and time according to the table of the construction and reset them once / day.  You can try those external booting as well.

  (4) If a problem occurs and the file write crashes your queue can fill.  The dequeue item is already waiting for data before it does anything, so I don't think you need the delay in the same loop.  This could help the dequeue catch up if the queue is large.  You can use a vi Get Queue Status to display the number of items in the queue on the screen.  As long as it is not hidden by the error message it could give you an idea if the queue is the cause of your error.  You can also access the queue size to see if it develops.

  (5) If your data acquisition loop error handling is not good, a mistake it can cause the loop to run as fast as possible.  If you have added the 1000ms wait just to show that this is not a gourmet loop, so this could easily be the cause.  I do not think that the Renault USB are very reliable, so try to use a days may run into this error.

  I hope that it becomes at least you said in the right direction.  My bet is on #5

• When I tried to installHoyelpuzzle and Board of Directors, it was installed but that it would not complete the installation

  I installed several card games again and had no problems.  But when I tried to installHoyelpuzzle and Board of Directors, it was installed but that it would not complete the installation. I have

  Windows Explorer and uninstalled until I reinstalled it.  I've done 4 times.  He went all way through the process, than to see a message that Setup could not be resumed.  Given that the other two disks of Hoyle have been correctly installed, why do I have problems with the drive of Hoyle puzzle and board? I contacted Hoyle and does everything that they told me to do.  But without success.  What could I do it wrong?

  Hello

  (1) what is the operating system that you use on the computer?
  (2) you get error codes?
  If you use Windows 7, Hoyle Board Games is not compatible with Windows 7.
  You try to install the game in compatibility mode.
  Click on the below link to check the compatibility of the game.
  http://www.Microsoft.com/Windows/compatibility/Windows-7/en-us/details.aspx?type=software&p=Hoyle%20Board%20Games&v=Encore&UID=&pf=0&PI=9&s=Hoyle%20card%20game&OS=64-bit
   
  You can check the link below:

  Make older programs in this version of Windows

  http://Windows.Microsoft.com/en-us/Windows7/make-older-programs-run-in-this-version-of-Windows
   
  You can check with the manufacturer of game for patches to run the game on Windows 7.
  http://support.Encore.com/
  I hope this helps!

• Windows (8) could not complete the installation.

  I just bought a new HP2000 today. I get home and start of implementation. At the end of the process, when it * must * be showing me the office (or whatevert, they call the thing in W8), I get this error message. I click 'OK' and it reboots and starts the whole process. How "complete the installation?

  I'm about to take over and get a gateway or a Toshiba!

  Try running a system recovery tapping away to the F11 key, immediately after switching on. It's just to rule out the possibility of a flaky installation which can be corrected by a factory reset.

• XP is unable to complete the loading and the power of travel.

  XP is unable to complete the loading and the power of travel. It will restart in Mode safe with no problems and then restart to normal safe mode. All programs and everything seem to work OK. CHKDSK/r was run from the installation disk and indicates disk errors have been corrected. Restart the hibernation or standby also works. Ntbtlog.txt is still crushed by the boot of good last and there is no help. It's very long and repeat the load lines and has-no-charge several times! Any ideas what to watch?

  I have lived with this for a few months and reinstalled XP and then new service Pack 3. Nothing done until this difference

  Hmmm...

  NVIDIA drivers are definitely outdated.

  If the system just stops (literally goes off), I suppose a marginal connection inside, an out-of-date driver or a heat problem.

  You can carefully and without requiring too much force, remove one reinstall all you cable and connection inside including your RAM and all other devices installed just do one thing at the time, so you don't mix.  One thing at a time... Unplug it and plug it in again.

  If she runs in Mode safe, your it would mean that the system uses the default XP video drivers (that is why everything is so GREAT in Mode safe).

  When you start normally and will charge drivers NVIDIA, things will run more hot.  Will increase the time on the CPU and video card.  Make sure that all your fans are running, and the system is properly ventilated and ventilated.

  If the CPU or processor on the video card is a problem of heat it just stop - no warning, no newspaper, no nothing.  Cool that turned off for awhile and it could work again for a bit.

  I use the NVIDIA site and let scan them online take a look at your video system and see what he suggests for drivers and consider their analysis if they offer a new driver.

  It is recommended to run the scan NVIDIA with Internet Explorer.

  Here is the address of the NVIDIA page:
  http://www.nvidia.com/download/Prescan.aspx?lang=en-us

  Read the instructions, and then click the GRAPHICS DRIVERS button to start the scan.

  You must be on the 275.33 version and you are now on 178.13 (from you given msinfo).

  6.14.11.7813 driver version<---- nvidia="" version="" 178.13="" from="">

  Your msinfo32, video section should look like this when you are finished:

  6.14.12.7533 driver version<--- the="" latest="" nvidia="" version="">

• Unable to complete the installation of windows vista, error message "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation.

  I'm install windows vista Ultimate edition in my new laptop, but during the installation stage 'completion', the prompt message as "Windows cannot configure one or more system components to install Windows, restart the computer, and restart the installation", but my new laptop was no install any OS before, please help

  tan7655,
  If I read this correctly, you have a portable computer that do not have an operating system on it.  You try to install Vista and get the error.
  You've restarted the Vista installation?  So then you get the same error? If you have tried to install more than once and continue to receive this error, check that the laptop is capable of Vista?  You may need to check with the manufacturer of the laptop to see if it is able to support Vista. Mike Microsoft responds to the technical support engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Windows could not complete the installation. To install Windows on this computer, run the Setup again.

  Hello, here is the thing.

  Reformatted a computer with recovery discs...

  Office to the top and everything looked ok...

  Windows Installer started and makes the computer reboot several times as usual.

  BUT NOW I have a black screen with a window saying "Windows is unable to complete the installation. To install Windows on this computer, run the Setup again. »

  I opened the Task Manager and closed a 'runonce' process, which got the Explorer will... But shit message will not go away, if I close the computer restarts!

  Why did I get this? How can I make them disappear? Windows has not installed correctly? Do I need to install any additional substance to compensate for this?

  + I just noticed there is no partition for recovery in my computer... you know? This thing of 2 GB next to Local disk c

  Hello, here is the thing.

  Reformatted a computer with recovery discs...

  Office to the top and everything looked ok...

  Windows Installer started and makes the computer reboot several times as usual.

  BUT NOW I have a black screen with a window saying "Windows is unable to complete the installation. To install Windows on this computer, run the Setup again. »

  I opened the Task Manager and closed a 'runonce' process, which got the Explorer will... But shit message will not go away, if I close the computer restarts!

  Why did I get this? How can I make them disappear? Windows has not installed correctly? Do I need to install any additional substance to compensate for this?

  + I just noticed there is no partition for recovery in my computer... you know? This thing of 2 GB next to Local disk c

  Hey Abraham G

  you use discs of recovery that are made for your brand and your computer model

  and if you have problems using the manufacturer's recovery disks, you will need to communicate with them about

  It's their recovery process not microsofts

  Walter, the time zone traveller

• BitLocker: Could not complete the requested operation because of...

  Two days ago Windows 10 was running on my laptop. BitLocker has been on two disks (D and E). For some reason, I have formated Win 10 and do a new install of Windows 7 Ultimate. After installation, when I unlock the drive D, it works very well. But I can't unlock the E drive. When I enter the password, the message "Could not complete the requested operation due to a catastrophic media failure or corruption of data on the disk structure."
  I'm sure that the password is correct at 100%, but I do not have any file recovery. Can someone help me?

  Hi NooriSAN,

  Thanks for posting your query on the Microsoft Community.

  According to the description of the problem, you cannot unlock a drive locked by Bitlocker key and get error message: "Could not complete the requested operation due to a catastrophic media failure or corruption of data on the disk structure."

  This could be if defective media stored on database security, or a program in the security software error has caused corruption on disk.

  For reference I suggest you to return the items mentioned below.

  In Windows 7 BitLocker Drive Encryption: frequently asked Questions

  Overview of BitLocker Drive encryption

  What are the main issues for Bitlocker?

  Hope that the information provided is useful. Let us know if you have any concerns related to Windows. We will be more than happy to help you.

  Kind regards