List of the USB pins map mother MSI MS-7778 Jasmine

Similar Questions

• My Lexmark printer stopped working and the error message says "printer cannot communicate with the computer" (from "twisted into the USB pins?).

  When my printer stopped working because of error messages about "printer cannot communicate with the computer" (from "twisted into the USB pins?), I tried to change to 2nd USB port without success. I tried a new cable; that did not help.

  Then I uninstalled and reinstalled my Lexmark printer and changed the error message. Now, the printer does not work because "the USB device is not recognized."

  I tried to update the chips; Use 1 USB port; and using the old cable, all this without success. I checked the connections of the cable to the printer and the PC and turn on the printer and goes off; I'm out of ideas. Any other suggestions?

  Hi ChristineKrause,
   

  Here are some links that might help you:

  Peripheral USB is not recognized when you attach it immediately after that your Windows XP computer comes out of standby or hibernation

  Advanced troubleshooting tips for General USB for Windows XP problems

  Try the steps listed in the items mentioned above and see if that helps you solve the problem.

• BlackBerry Smartphones to Blackberry Manager devices to display the USB PINS

  My Blackberry Bold 9000 is not recognized by my office blackberry Device Manager.  After hours of playing around to try to solve this problem, here is what information I can provide.

  My desktop and laptop running Vista 64-bit.  I had no problem installing the Desktop Manager on my laptop and cable, updated processes, etc. all work fine.  In my view, this allows me to isolate the desktop and not the device or the cable. The Desktop Manager software is to date on both systems.

  When I try to get the Blackberry device manager to recognize my camera on my desk, in the table options of connection under connection, that COM1 is displayed, Disable stateful shown.  USB-Blackberry 9000 (Paperback) appears on the laptop.  I've hunted around these tips and google for a solution to this problem, but I have not yet found one.  Under the Windows Device Manager, "Blackberry Smartphone" is listed under USB controllers when the unit is plugged, and the drivers are updated according to the instructions on these cards.

  The functions of USB ports for the operation of the keyboard, mouse, and external storage.  I tried to connect to all six USB ports in the back and two on the front of my office, without result.  When the device is connected to my desktop computer, Windows recognises the Smartphone and SD card separately as mass storage devices - with the phone powered on or off mass storage device option.

  I have a feeling that this would be resolved if I could get the Blackberry device manager to display a USB instead of COM1 port.  Someone at - it solutions?

  Hey this is my solution... it worked perfectly for me, and oddly enough, this is a difficulty for VMWare (also the difficulty to detect USB devices)

  Try to right click on one of the USB hubs (in Device Manager) and looking at the details of the driver. If usbfilter.sys is in the list then open your registry editor and navigate to: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class {36FC9E60-C465-11CF-8056-444553540000} and remove the UpperFilter, pair of usbfilter.

  I restarted after making this change, and it works fine now.  Its the first time in the month that I could plug my Curve 8900 using my USB on my PC 64-bit of Windows Vista (now Windows 7).

  KUDO to the population of VMWare for this solution.  Thank God, she also fixed for my BB Desktop Manager! WOOT WOOT!

  Here is a link where I found this solution

  http://BX.BusinessWeek.com/consumer-arbitration/view?URL=http%3A%2f%2Fcommunities.VMware.com%2Fmessa...

  Merry Christmas everyone

• Manual of the motherboard for desktop P7-1414 (Jasmine MSI MS-7778)

  Hi all

  I've been looking for a mother MSI MS-7778 map manual with no luck... does anyone have a link or an idea where I could find this? Specifically, I'm looking for the connections of cables... like the connection light of the hard disk on the header.

  Thank you

  CN

  Cheesnacho,

  This helps with your requesr for the front panel header?

  

• Compaq Desktop Front panel usb pin possiblity S6300nx

  Understand the standard pin #s for usb, but my braces usp of façade looks different with son only go (first level of level two connectors) to the pins 1,5,7,9 #, 3 # ignored. so that my profile looks like: 1 5 7 9

  6 2.4 x 8.  What is the assignment of women?

  It seems that your computer uses the motherboard Kamet2.

  This Manual seems to be for your motherboard that it corresponds to the specifications.  Page 11 is the USB pins and what each is for.  Based on the schema, it looks like they are all used.  Pin 3 in your diagram would be USB p6-.

• Therefore each SATA in my Win7 x 86 device listed as an ejector device when I'm ready to eject the USB device?

  Just at the moment where I thought that my Windows 7 Pro 32 bit environment worked perfectly, one day, I was ready to eject a USB device, I plugged, I saw ALL my devices SATA appearing alongside my USB items which have been plugged, including my C drive!

  Why is this?  How, all of a sudden all my readers (internal and external) appear as removable safely disks in my Win7 32 bit and not in my Win7 64-bit (yet)?  And how can I fix this problem so that my SATA devices are not among my USB devices?  One SATA device should be listed; and this is my backup of Master, plugged in a socket of SATA_A1, for which the SATA_A2 is shared by the eSATA plug.

  Here is a little information about my hard drives and the ATA channels to which they correspond:

  B: System reserved / F: 64 - bit Windows 7 - ATA Channel 0

  [Simple walk; reserved my win7 system 64-bit is not hidden to prevent my win7 32-bit access it.]

  X: Master Backup - ATA Channel 0

  [No misspelling; my Device Manager is showing TWO ATA Channel 0 s in the list of ATA/ATAPI IDE controllers.]

  C: 32-bit Windows 7 - ATA Channel 1

  [The main reader.]

  ATA Channel 1

  [Unknown as of yet what this ATA Channel 1 corresponds to.]

  Primary data G: - ATA Channel 2

  [For additional storage.]

  Secondary data H: - ATA Channel 3

  [For additional storage.]

  D: Blu - ray - ATA Channel 4

  E: DVD Burner - ATA Channel 5

  Now for my Win7 64-bit, Disc C installation (which is my first hard drive) represents my 64-bit Windows 7 and partitions B and F (for my second hard drive) my 32-bit Windows 7 with its partition system reserved for B.  Everything else is the same, but...

  ... In my Win7 64 bit environment, my IDE ATA/ATAPI controllers list has only 2 ATA channels; 0 and 1, no duplicates.  I haven't checked for correspondence of these channels, but I'll bet that channel 0 belongs to Drive X and 1 channel belongs to the C drive.

  How is it that, in my environment 32-bit, an ATA channel has been assigned to each disk in my machine, and how to disengage and remove the assignments without losing access to all these readers?  I don't have this problem before, and I can't determine when the problem first occurred.  I can't uninstall ATA channels 2, 3, 4 and 5 of my device manager, afraid that the corresponding drives disappear from my Explorer and becomes completely inaccessible.

  UPDATE:  He finds that, for some unknown reason, my SATA AHCI controller has been replaced, which displays all my readers as removable.

  First thing I did was make an update, I think it was almost a downgrade, to the standard AHCI driver provided by Windows.  All readers always displayed as removable.

  Then I did an update; This time, instructing the Device Manager to search for the driver accompanying DVDs of the card from my mother...

  ... And here!  After a restart, only displayed as removable drives are X Drive and everything I plug into the USB ports.  In my device manager, only ATA 0 and 1 (no duplicates) channels are displayed.

• audio output lists only the internal speakers when usb is connected to the dac

  This problem happened after I had used my mbp for months as music server in a stereo system.  When I have the mbp connected via USB to an external digital to analog converter (dac), audio preferences had always listed the CAD.  Now it lists only the internal speakers.  I tried to reboot, checked my UBS cable, checked my dac.  The only thing I've done recently is to create a playlist and sync a new iPod to copy the playlist we.  I don't know if that could have anything to create the problem of lack of dac, but I am a relative novice on computers.

  Anyone have this problem or knows how to fix?

  -Try other USB port

  -The signs to see the CASD of life like the lights on?

  -Maybe the CAD failed.

  -Try the following

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  https://support.Apple.com/en-us/HT201295

  Subject of memory NVRAM and PRAM

  https://support.Apple.com/en-us/HT204063

  -Try to start safe mode

  OS x: what is Safe Boot, Safe Mode?

  https://support.Apple.com/en-us/HT201262

  -Start to recovery and repair the startup disk

  OS X: on OS X Recovery - Apple Support

  https://support.Apple.com/en-us/HT201314

  -If it is repairable reinstall the OSX

  How to reinstall OS X on your Mac - Apple Support

  https://support.Apple.com/en-us/HT204904

  -If you do not have a backup using disk utility to restore the internal drive to an external drive, so that you can try to recover the data.

  Format the boot disk and then do a fresh install of Mac OS x

• Got a 27 "monitor from Apple, with thunderbolt (error). My MacPro can't love at first sight. Apple won't bring back the monitor. Will using a USB 3 map and then using a hard drive with USB 3 and Thunderbolt works?

  Got a 27 "monitor from Apple, with thunderbolt (error). My MacPro can't love at first sight. Apple won't bring back the monitor. Will using a USB 3 map and then using a hard drive with USB 3 and Thunderbolt works?

  N ° you need a computer logic board which has built in Thunderbolt.

• How to get the USB device in the list in the resource name field VISA VISA Open VI

  I followed the tutorial below to connect with my camera using the USB port. But I don't have the name of the USB port able & Automation Explorer list devices. How to get it? Can anyone suggest something?

  http://zone.NI.com/DevZone/CDA/tut/p/ID/4478

  Hi kimhyun,

  I tried this. But managed. I used the USB as my sugesstion to device.my USB is that you unplug your device at any point of your work. Check that the device is properly connected. IF your system has recognized your device, you can view the device in Control Panel > Device Manager > then open your particular device from the list of the connected device then details > description of the system > hardware ID > then you can find here the code from your provider.

  Try this. I think that your device is connected to loosen. What USB device you are using? Also, you must install THE DRIVER FOR YOUR USB DEVICE.

  Good luck

• Windows 7 x 64 upgrd dv6500z disconnected network drives allow usb drive mapping to the same drive letter

  Hello

  I'm having a problem with the readers of network disconnected allowing for new drive usb to their drive letter mappings. I have my laptop dv6500z home with windows 7 Home premium connected to my router wirelessly with a couple of shares of x 64. Now I turned off, trip and start. All right, the drive letters show as disconnected as they should. Now I plug in a USB key and it corresponds to the drive letter of one of the disconnected actions and not a new, unassigned drive letter. In Explorer, there will still be disconnected action description. Click on it and it accesses all my files on the USB key. In admin tools/disk management, the correct label for the USB key is displayed.

  So is it a problem of HP or just a problem of Microsoft with Windows 7?

  Woody, I was able to replicate that XP is not a bug but a feature. On my laptop, it originally had vista on the c drive and a recovery on the d drive partion. There are about 1 1/2 years I have upgraded Vista to XP. Then recently updated to Windows 7. kept the 3 OS's so I got triple starting capability. Then at home, I added 3 network shares, while I was using a lot of drive letters. When actions are undone, Windows maps a USB key which has not been connected before system one of the disconnected but readers still show in Explorer, the name of the drive on the part of disconnected. However, if the USB is connected to the system before, Windows appears to map a drive letter that he remembered from before.

  In my case, Windows 7 has been installed recently, so there is no remebered for my USB drive letter. I was away from home, so I had a lot of disconnected shares. In addition, now that I got a 3rd OS added to the system, I used a lot of letters from the GET go by car. It's much more likely that I would meet this feature after installing Windows 7.

• Where can I reallocate the letter of a mapped network drive? In addition, where to see a list of the letters in use by mapped network drives?

  Change the mapped network drive letter

  Letter h: is not available to map a network drive.  Also, it is not listed in the disk management window.  None of my other mapped network drives are no more.   Where can I reallocate the letter of a mapped network drive? In addition, where to see a list of the letters in use by mapped network drives?

  Tips on how to assign a drive letter:

  http://TechNet.Microsoft.com/en-us/library/cc757491 (WS.10) .aspx

  See also:

  http://answers.Microsoft.com/en-us/Windows/Forum/Windows_7-hardware/can-not-change-drive-letter-Windows-7/37a22203-6add-46e4-8f1d-997b130db362

• iTunes does not list my ipod touch when I connect with the USB cable

  I bought an I - pod and put in place, but when you plug the USB cable, I-Tunes does not show the unit. Just down loaded music in my computer for the I - Pod so that it is on that point.

  Hello

  You use the Apple software (iTunes) and Apple (iPod) hardware.

  You must contact the Apple Support.

  "IPod Troubleshooting Wizard.

  http://www.Apple.com/support/iPod/five_rs/

  Or the iPod of Apple communities.

  https://discussions.Apple.com/community/iPod/Ipod_touch?CategoryID=221

  Or ask iTunes Support.

  "iTunes support-how to use iTunes.

  http://www.Apple.com/support/iTunes/

  "Contact iTunes Support.

  http://www.Apple.com/support/iTunes/contact/

  Or ask in the community Apple iTunes:

  https://discussions.Apple.com/community/iTunes

  See you soon.

• The Device Manager on my Windows box lists a hub USB 3.0 as one of USB controllers. This means that one or more of the USB ports are capable of 3.0?

  I recently bought a backup disk says he would run faster is it my 3.0 instead of 2.0 USB ports.

  Just try to understand the computer itself, if one of the 8 USB ports on my desktop Dell (Windows 7, 64-bit box) is capable of USB 3.0.

  Hi John,.

  The message that Windows gives is Windows telling you put a USB 3.0 device in a USB 2.0 slot and the speeds will be Cap using USB 2.0 footrest.

  If you are looking for your system on the website of Glens, it should tell you if one of the USB ports are 3.0 or not.  I think that USB 3.0 is marked with the blue wire around the ports.

• USB microphone is not listed in the Audio of first drop down hardware

  Hi all.

  First of all, I would be grateful very gladly any idea here because I'm totally stuck with this tent to record a voice on the track.

  The title is pretty self-explanatory. I work on Mac OS X and first Pro CS5 and I would like to record an audio track, but the USB microphone is not displayed. I have already read several forum discussions and followed the steps, but this problem has not yet been mentioned.

  That's what I did several times without success:

  1 - Connect the USB cable and check that MacOS recognizes. It works very well.

  2 - in Premiere Pro mark taken as a track record. Error message because no input device has been declared.

  3 - premiere Pro > > Preferences > > Audio-Hardware-> no microphones on the menu drop down.

  4 - Open audio and Midi and I add all microphones to Premiere Pro (Line-In, built-in and USB device).

  5-return to step 3: reopen the project > > Preferences > > Audio-Hardware-> Line-In and integrated appears, but not yet of micro USB.

  I was able to record with the built-in microphone, but I don't know what is happening to the USB one. In fact, if I go back to step 4 and open the audio and Midi, boxes that I had checked once reappear unchecked.

  I don't understand what is happening. Thank you in advanced for your help.

  I'm a PC guy, but if I had your problem I would try to turn off the microphone integrated and entry at the level of the BONE, so that the only possible option for the operating system and applications of line would be the USB microphone.

  I use a Logitech USB headset and Pr CS6 has no difficulty to recognize or record with her.

  Jeff

• 0Y5CWX model of card mother Dell Inc. (XPS 12 9250) need manual or help locate the CMOS pins

  Where are the CMOS pins on the motherboard 0Y5CWX?

  There is no "CMOS pins.  If what you're trying to do is reset to the default values, just disconnect the battery and hold the power for 30 seconds.

  If you try to reset a password, note that it is not stored in the CMOS - it is stored in the EEPROM.  The only way to do it is get an unlock code by calling Dell, verify your ownership of the system and entering the password they generate for you.