(Management and port number) firewall rules

Similar Questions

• What is my e-mail server name and port number

  Unable to send a scanned document because I don't know my server name and port number

  Your e-mail account provider has that information.
  They should have a help page on their Web site.
  If you tell us who provides your email account, maybe someone can help
  you.
   
   
   
  --
  Dave N.
  MS - MVP (Mail)
  Windows 7 Ultimate
  http://download.live.com/wlmail
   
   
   
  "badrisk" wrote in message news: eec85ab4-ac81-44d 9-a285-8aec5cdf9cb7...
  > cannot send a scanned document because I don't know my server name and port
  > number
  >
  >
  >
   

  Windows 7 Ultimate 64

• How to change the name of the ODI agent and port number

  I installed ODI standalone agent (11g) on a linux server.  We now realize that we need to change the name and port number of the agent.  Is it possible to change these or do we need to re - install odi agent?

  I know that I can change the name in the ODI, but I can't change the port number.  I would like everything to be consistent in all of our environments.  That's why we need to change the name of the agent and the port number.

  How do you start the agent? Which command you use to start?

  There are two ways, either by directly calling agent.bat and passing name agent and port don't start or you can run the sh/bat file created during installation (present in oracledi\agent\bin). The file name that is created should look like this (agent_localagent11g) where localagent11g is the name given during installation time and 'agent' is the prefix that was added by ODI.

  There is no configuration file to configure the port number and agent. Make sure that the port number and name you pass to agent.sh must match what is configured in odistudio.

  Agent.bat '-PORT = 20910 ""-NAME = localagent11g.

• Multicast address and port number number

  Hi, I set up a cluster with the multicast address and the multicast port number. But unfortunately, there is another cluster in another domain with the same multicast address and the same port number. Now I need to find the other area that is having this multicast address and multicast port. But I'm not able to do. Is it possible for that?

  Its weblogic.cluster.MulticastMonitor
  http://download.Oracle.com/docs/CD/E13222_01/WLS/docs100/cluster/multicast_configuration.html

  You could restrict that to the IP address by using this utility.
  If you have a large number of areas on this machine as well, then I think you can use netstat to understand the exact field.
  You may even consider the above debugging flags.

• RVL200 - SSL VPN and firewall rules

  Forgive my ignorance, but I have been immersed in the configuration of this device RVL200 to allow Remoting SSL VPN to a customer site, sight unseen.  I have the basics of the VPN set up in config, but now move the firewall rules.  We want to block all internal devices to access the Internet, but I don't want to cripple the remote clients that will be borrowed by blocking their return via the SSL VPN traffic.  This leads to my questions:

  (1) a rule of DENIAL of coverage for all traffic OUTBOUND will prevent the primary function of the VPN (to allow the administration away from machines on the local network)?

  (2) if the answer to #1 is 'Yes', what ports/services do I need to open the side LAN?

  (3) building # 2, configuring authorized outbound rules apply only for VPN clients, rather than all the hosts on LAN?

  (4) as the default INCOMING traffic rule is to REFUSE EVERYTHING, do I have to create a rule to allow the VPN tunnel, or guess that in the configuration of the router?

  Here are some other details:

  • The LAN behind the RVL200 is also isolated LAN in a manufacturing environment
  • All hosts on this network have a static IP address on a single subnet.
  • The RVL200 has been configured with a static, public IP on the WAN/INTERNET side.
  • DHCP has been disabled on the RVL200
  • Authentication to the device will use a local database.
  • There is no such thing as no DNS server on the local network
  • The device upstream of the RVL200 is a modem using PPPoE DSL, and the device has been configured for this setting.
  • Several database of local users accounts were created to facilitate the SSL VPN access.

  I worked with other aspects of it for a long time, but limited experience with VPN and the associated firewall rules and zero with this family of aircraft.  Any help will be greatly appreciated.

  aponikikay, there is no port forwarding necessary to the function of the RVL200 SSL - VPN.

  Topic 1. That is not proven. It shouldn't do. The router should automatically make sure that the SSL - VPN router service is functional and accessible.

  Re 2. No transfer necessary. In addition, never before TCP/UDP port 47 or 50 for VPN functions. The TCP 1723 port is used for PPTP. UDP 500 is used for ISAKMP. You usually also to transmit TCP/UDP 4500 port for IPSec encapsulation.

  Let's not port 47. ERM is an IP protocol that is used for virtual private networks. It is a TCP or UDP protocol. GRE has 47 IP protocol number. It has nothing to do with TCP or UDP port 47. TCP and UDP are completely different protocols of free WILL.

  It goes the same for 50: ESP is the payload for IPSec tunnels. ESP is the Protocol IP 50. It has nothing to do with TCP or UDP port 50.

  'Transfer' of the GRE is configured with PPTP passthrough option.

  'Transfer' of the ESP is configured with IPSec passthrough option.

• NETGEAR ProSafe VPN Firewall SRXN3205 and port forwarding?

  Hi, this is a long shot, but I'm pulling my hair out at this point and can be a bit over my head, as I am new on network

  Small short story, I have two servers, one is the NAS box (IE if I connect via the internet to the site via public IP network from home, I get it that site says 'my actions' I insert login and pass and get access to them.)
  That is, everything is peachy.
  The problem is when I try to connect to my FileMaker Server I'm not and instead, he takes me to the login NAS box. So I think ok, I need to port forward (5003 for filemaker) to go to different PC local LAN(192. etc)

  Security > firewall > Add Service entering:
  Service: fmserver
  Action: Always leave
  Send to LAN Server: unique address 192. etc is filemaker installed on (and different on a NAS)
  Definition of Port number: 5003<-- is="" this="" right?="" how="" else="" would="" you="" indicate="" you="" want="" all="" connections="" on="" this="" port="" to="" go="" to="" this="" specific="" lan="" machine="" from="" internet="" instead="" of="" default="" which="" seems="" to="" be="">
  rest is default, I click on apply.

  Here's what I don't understand. In the table of incoming Services, (security > firewall) I have two local IP in the list, a SIN, the other for Filemaker. But only the top works and can be connected to. I can move every top position and it will work, but they will not work at the same time, just the one that sits on the top of the sad Smiley page

  and yes I read the manual again and again and don't know how I'm screwing up the port forwarding on this point, even if I am brand new to probably something stupid Smiley Happy (our work IT guy is gone so tried to get involved through this somehow)

  Any help would be appreciated.

  Hello sinieq,

  There is a hierarchy on incoming service table, which is normal. I see 4 services added using "ANY" (ALL use any port number) you will need to remove/disable these because of the rule of the hierarchy on the table, all other services will be ignored when EVERYTHING is used. What is the port number used by the NAS Server? I don't see a port defined to access NAS. Try disabling services by using "ANY" and try again by adding the translation to the port number of the NAS.

  Let us know what happens.

  Thank you

• VCloud 5.1 API c# edge Gateway service detailed configuration examples of code including firewall rules, rules Nat and DHCP.

  Hello world

  Everyone can share codes sample detailed to set firewall rules and NAT for c# rules?  I looked in the examples provided with the API, but I need more samples.

  Here is the example of function to configure the firewall to VCloud API 5.1 for c# rule.

  ///

  To create an object of type of firewall rule. This object is used to configure the firewall.

  ///

  Name of the rule

  Source IP address range

  Firewall Type protocols

  Type of firewall policy

  Source port

  Destiniation Ip address range.

  Destination

  Toggle rule

  Turn logging on or off.

  Firewall rule

  public static FirewallRuleType CreateFirewallRule (string name, string sourceIpRange, FirewallRuleTypeProtocols protocols, FirewallPolicyType action, sourcePort int, string destinationIpRange, int destinationPort, bool isEnabled, bool enableLogging)

  {

  Create an object of type firewall rule.

  FirewallRuleType firewallRuleType = new FirewallRuleType();

  Configure the setting was active user interface check box.

  firewallRuleType.IsEnabled = isEnabled;

  firewallRuleType.IsEnabledSpecified = true;

  Set the description of the rule from the user interface name text box.

  firewallRuleType.Description = name;

  Normally, this is a port number.

  firewallRuleType.SourcePortRange = sourcePort.ToString ();

  firewallRuleType.SourcePortSpecified = true;

  Configure the Protocol

  Protocol of var = new FirewallRuleTypeProtocols();

  Value of the Protocol Set object

  Protocol. Items = new Object() {true};

  Define the name of element

  Protocol. ItemsElementName = new ItemsChoiceType [] {ItemsChoiceType.Tcp};

  Protocol Set

  firewallRuleType.Protocols = Protocol;

  Set the destination IP address range

  firewallRuleType.Item = destinationIpRange;

  Normally this is the port number.

  firewallRuleType.DestinationPortRange = destinationPort.ToString ();

  Set Source Ip range

  firewallRuleType.Item1 = sourceIpRange;

  Configure logging check box UI activate recording.

  firewallRuleType.EnableLogging = enableLogging;

  firewallRuleType.EnableLoggingSpecified = true;

  Configuration by default allow/deny action.

  firewallRuleType.Policy = action. Value();

  Return firewallRuleType;

  }

• SRP527W setting DHCP address and source firewall rules

  In my quest to find a decent ADSL router for VoIP, I found the SRP527W and so far it has been the best performer of a range of boxes from netgear, thomson, and zyxel.  However, I have two questions:

  (1) how to troubleshoot DHCP leases on the LAN address

  (2) how to specify source ip in the firewall rule

  Note:

  I currently have 1 computer on the LAN, VLAN1 interface

  * 192.168.15.100

  and

  2 IP phones on the LAN, VLAN100 interface

  * 192.168.100.100

  * 192.168.100.101

  Address three assigned by the DHCP server lease times with approximately 20 days.

  I would like to repair the three devices DHCP leases, for example if some port forwarding rules can be made with confidence that the rules will not point to another device in the future.

  from PVC0-> 192.168.15.100, Port 3389 for remote desktop

  of PVC0-> 192.168.100.100 ex.port 5881 to int.port 80 for voip phone web-gui

  from PVC0-> 192.168.100.101 ex.port 5882 to int.port 80 for voip phone web-gui

  Ideally, I would like the rules to act like that, limiting myself only to access these ports (from my remote site)

  PVC0 interface where the source is ip 12.34.56.78-> 192.168.15.100, Port 3389 for remote desktop

  PVC0 interface where the source is ip 12.34.56.78-> 192.168.100.100 ex.port 5881 to int.port 80 for voip phone web-gui

  PVC0 interface where the source is ip 12.34.56.78-> 192.168.100.101 ex.port 5882 to int.port 80 for voip phone web-gui

  I hope that makes sense, I appreicate any help you can give.

  Kind regards

  Paul

  Hi Paul,.

  Thank you for using the Cisco support community.

  With regard to two questions:

  1. Yes - it is possible to configure static DHCP assignments.  Use the DHCP Server rule configuration page and click the 'Show DHCP booking' button to assign.

  2. Unfortunately, it is not possible to configure rules to address source for the SRP520 list.  (This is possible on the SRP540 for further reading).

  Kind regards

  Andy

• RV320 firewall rules, VLAN and IP Aliasing

  I bought and RV320 to replace our router SA520W.  I have 2 servers SBS located on the VLANS separated.

  The 320 RV is set with 1 WAN IP XX. XX. XX.43

  SBS1 a IP internal of the XX. XX.16.2 on VLAN 1 port 1 on the router

  SBS2 a IP internal of the XX. XX.2.2 on the VLAN 5 port on Router 2

  On the old SA520W, I was able to configure alias IP XX. XX. XX.47 and XX. XX. XX.46 with firewall rules if 47 designated SBS1 and 46 stressed SBS2 to their respective ports.

  How to make on the RV320 so I can have 2 isp server IP addresses to go through WAN1 to their VLAN respective?

  SBaalman1,

  The feature you're looking for is called NAT of individuals on most routers Cisco SMB. You can find under Setup.

  -Marty

• Port number of the IP address and CC

  I have problems with CC of messages telling me I'm not connected or connected, but I still go to the app. Several times I'm not able to update either. My Manager asked me to ask the IP address and the port number used for cloud to adobe. Anyone know?

  Hi Jan,

  Please see the About Adobe Creative Cloud Packager

  I hope this helps!

  Kind regards

  Sheena

• Firewall Windows has been disabled by a virus or Malware. System is now cleaned and Salvation took up the Task Manager, but the Windows Firewall service does not start. How to run again.

  Firewall Windows has been disabled by a virus or Malware. System is now cleaned and Salvation took up the Task Manager, but the Windows Firewall service does not start. How to run again.

  Suggest you read the following: http://answers.microsoft.com/en-us/windows/forum/windows_7-security/virus-recovery-error-codes-0x80070424-and/28ed2ede-076c-4955-bb49-44d0c2ee1ed3

  I hope this helps...

• Windows7 when I migrated to the Working Group at the field of the firewall has crashed. And also it does not show in the services. In the firewall rules of incoming and outgoing traffic is missing.

  In my windows7 when I migrated to the task force to the area, crashed by the firewall. And also it does not show in the services. In the firewall rules of incoming and outgoing traffic is missing.

  Hello arjunpottekkad,

  It is disheartening to know that have problems you with the firewall. As I understand it the incoming and outgoing traffic rules are missing from the firewall.

  The question you posted would be better suited in the TechNet Forums . I would recommend posting your query in the TechNet Forums. You can follow the link to your question:

  Windows 7 IT Pro category

  Answer to us if you are having problems with the Windows Firewall or any other problem of Windows, and I'd be happy to help you again and try to correct the problem as soon as possible.

  Good day!

  Hope this information helps.

• I am using oracle 11g express edition, how I can change the service name and the port number?

  I am using oracle 11g express edition, how I can change the service name and the port number?

  I am using oracle 11g express edition, how I can change the service name and the port number?

  What do you mean by "port number"? HTTP port (usually 8080), or listening port (normally 1521)?

  To change the name of the service, you can use (as a DBA or SYSDBA)

  SQL > alter system set service_name = '';

• Slow computer and the number of processes in the Task Manager

  My dad's computer runs very slow on start up, and when you try to shut down some programs it freezes or just takes its time.  When it freezes, I use the Task Manager to close the program, which usually works.  SE when I had to use Task Manager, I noticed that my father has 53 process running at a time.

  Could it be slow down the computer and if so, what can I do about this problem?

  You can search what process you use cpu on the Task Manager and stop the process.

  Under steps:

  1. right click on the taskbar.

  2. click on the Task Manager.

  3. click on the processes tab.

  4. double-click on the CPU.

  5 is if "system idle process" is max.

  6. If it is not a right click and click on end process.

  Learn "why is my computer running so slow?" and "how to fix":

  http://downloadlk.com/WhyIsMyComputerSlow.htm

  Use the tool: http://downloadlk.com/themosteffectiveregistrycleaner.htm

• [Solved] Research of firewall rule allowing Windows Update

  The problem has been resolved here: https://social.technet.microsoft.com/Forums/en-US/62b9fd5c-10b2-4266-bc15-fcf3e79d20d4/solved-windows-firewall-rule-that-allows-windows-update?forum=w7itpronetworking

  Everything down here is obsolete. (But you can read the true story about the virus of Bagel).

  Someone at - it an outbound Windows Firewall rule allowing Windows Update?

  Details.

  Yesterday, I tried to run Windows Update. The rule of outbound firewall to allow Windows Update to get through, I added was:

  Name: Allow Windows Update
  Group:
  Profile: Public
  Activated: Yes
  Action: allow
  Program: %SystemRoot%\System32\wuapp.exe
  Local address: no
  Remote address: all
  Protocol: all
  The local railway: no
  Remote port: any
  Computers permit: all

  I got 10 updates to install and all 10 failed. The only way that they have all been able to fail is: '% SystemRoot%\System32\wuapp.exe' is the wrong program, OR "wuapp.exe" passes control to another program, I don't know.

  Can anyone help me with this? I'll be forever grateful if you can.

  Note that I had to fall back to the default settings (see 'Background', below) in order to succeed and who has not made me happy.

  Background.

  Despite what you think it means, "outbound connections (green check mark) that do not match a rule are allowed" (which is the default) means only, unless you went to the extreme penalty to create the blocking rules, the firewall is wide open for outbound - connections, essentially, you have no firewall for outbound connections. " That means, 1, if you have a Trojan horse on your computer that is looking to download his main-payload of viruses in your computer (see "A history of real virus", below), or 2, if you have a virus keylogger in your computer who wants to 'phone home' him make his Masters criminal of your online banking user name & password There is absolutely nothing to stop.

  That's why I put my firewall: "(entry not red) outbound connections that do not match a rule are blocked".

  A story real virus.

  A couple of years ago, I visited a well known web site that had been hijacked - was - it cnet? I think so. The site seemed basically OK, but something made me shy away. I've left without clicking anything whatsoever. But the visitor of this site (with active javascript) transferred a Trojan horse in my computer (i.e. "Trojan", below).

  Once it was in my computer, the Trojan horse, then went through my firewall, out - was my firewall zonealarm at this time? I think so - and downloaded Bagel, a key logger to rootkit.

  I had no warning of the firewall as the Trojan horse used a well-known port that was wide open, and I had no antivirus warning because Bagel does not change any existing program. It uses the unallocated file space, patched itself in the initialization string, charged before the mode protected of windows at the next startup and reprogrammed the hardware memory to hide its presence in memory. It took me 2 months to discover Bagel and another 4 months to get rid of him. It was hell. My keyboard and mouse acted constantly upward. I didn't a bank online at this time. If I had, I'm sure that my account would have been cleaned up because that's what Bagel. It's a keylogger monitoring keyboard and browser waits to catch a connection to the Bank.

  Details of Trojan.

  The Trojan horse was a javascript function which ran automatically when the page is loaded. He created a table (similar to a mathematical object matrix) made up of identical over 1 million members of the group. Each Member of the Group was a short string of numbers. As it looped to add table-members, the Trojan horse later (in fractions of a second) overflowed the heap memory management hardware had allocated to my browser. That overflow has partially replaced the next higher segment in memory - which is called a "violation of the limits", and Yes, it is possible, if you position the base register just below the upper part of your segment and then use a large lag. There was a flaw in Windows that could not detect this type of violation of the limits and Bagel is designed to exploit this vulnerability. But the story does not stop there. To take control, the short string of numbers in a table-member of the "wrong"side of this segment limit had to be performed. Now, it of the roll of the dice that viruses are facing, but if the program that was partly crushed is always loaded in memory and running and if it executes the code at the bottom of its segment, then - Voila! -the virus takes control of the timeslice allocated to the program that was partly crushed. In other words, the program that was partly crushed no longer control, the virus is in control. So, what did the do Trojan horse? Completely in the background and without any idea for me, he went to a web site in Ukraine and downloaded the main payload of Bagel. How do I know all this? I looked at the javascript trojan and I disassembled - disassembly is as kind of decoding - the payload of Bagel (the rootkit) that I saved after I found some 6 months later. I still have the payload of Bagel sequestered in a zip in quarantine - in fact, I have a menagerie of dozens of viruses that I use to test antivirus programs.

  Hi Mark,

  Please keep us updated on the issue.

  I ask that you continue to try the suggestions in this article because the information in the article is good for Windows 7 as well.

  Please let us know the result.