Management E4200v2 remote problem

Similar Questions

• HP G60 - 117US LAN adapt will not connect. Vista Ultimate. Manager displays without problem. Can connect wirelessly. Use Nvidia MCP77MV chipset__

  My laptop will be wired adapter not connecting, Device Manager shows no problems

  Hi Baker,

  (a) if it works well before? You get a specific error message?

  (b) don't you recall making any changes to the computer before this happened?

  Connect the laptop to access the internet cable and then try to follow the steps:

  Step 1: check if you are able to receive the IP (Internet protocol) address, run Ipconfig/all at the command prompt.

  Click Start, run, type "cmd" (without the quotation marks), and then click OK to open a MS-DOS command line window. Type "ipconfig/all" (without the quotation marks), and then press the ENTER key.

  ·         Do you have an IP address?

  ·         You get the addressing APIPA (automatic private IP addressing)?

  Ø If the line "Autoconfiguration Enabled' says 'Yes', the 'Auto-configuration IP address' is 169.254.x.y (where x.y is the unique client identifier), then the computer is using AUTOMATIC private IP addressing.

  Ø If the line "Autoconfiguration Enabled' says 'No', while the computer does not currently use AUTOMATIC private IP addressing.

  Note:  With APIPA, DHCP (Dynamic host configuration protocol protocol) clients can be automatically configure an IP address (Internet protocol) address and subnet mask when a DHCP server is not available.

  If you cannot assign an IP address and then try step 2

  Step 2: disable the DHCP (Dynamic host configuration protocol protocol) Broadcast Flag:

   

  Run the fixit available in the link below to disable the DHCP broadcast flag

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers

  http://support.Microsoft.com/default.aspx/KB/928233/en-us

   

   

  Important This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base:

  How to back up and restore the registry in Windows

  http://support.Microsoft.com/kb/322756

   

  Let us know if it works

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• What is ECCN for the browser Firefox (v10 & v17) and Manager of Remote XUL?

  Lockheed Martin wants to distribute the United States to its employees (non-US) international one copy of Firefox and Remote XUL Manager. To do this, we require the ECCN classification for these two products. Can you please provide.

  Please refer to https://wiki.mozilla.org/Deployment:Deploying_Firefox #United_States_Export_Control_Information

• Labview Remote problem

  Hello!

  I have a NI USB DAQ of 6341 who assume to control a horse trough PMT and LED Labview 2010.

  But, Labview is not installed in my PC, I use it remotely from the University and I am facing problem to use DAQmx (version 9.3.5) in Labview.

  What I want to know is how to make my remote Labview for data acquisition in my computer.

  I guess it's a very simple question, but after hours trying to find a solution, I decided to ask the experts...

  Thank you!

  Hello RadGent,

  This solution will not work in your case.

  However with NOR-DAQmx 8.0 and later, NOR-DAQmx OPC features can be used to obtain the features of reliable network of remote systems.
  GDR (as mentioned in the document you provided) is not supported in NOR-DAQmx.

  You can try something like this:

  http://zone.NI.com/DevZone/CDA/tut/p/ID/3742

  The best and the most simple of measures to be taken would be to install the software locally, especially because you are working with a USB device.

  Goes on ethernet, at University, then return in the same pc to connect to the DAQ card would seriously increase the latency of the system.

• Causing the Windows Task Manager to Internet problems?

  When I open the Task Manager to change the priority of a program (change by normal normal CPU use above) it causes my ping in games to soar and I get huge lag spikes and possibly disconnect. I am running Windows 7 Ultimate 32 bit. I had no such problem with Windows Vista.

  Hello

  If you change the priority of any program in the Task Manager, performance of other programs will be hampered.

• Task Manager/System Restore problems

  I have Windows XP - from one day to the next, the Task Manager has changed appearance. All I can see are the processes. It does not show running programs, refresh, stop, etc..  So I tried System Restore and cannot restore.

  Looks like you can be / are the Task Manager running in mode tiny/small footprint.

  If you double-click on the empty space around the border of the screen of the Task Manager, it will change from normal mode, and then you should see the tabs you are accustomed to seeing.

  You can read about it here:

  http://www.BROADBANDreports.com/FAQ/6905

  If your system restore is also broken, why don't you start a new question/topic/thread for this since it's a different problem.

• Have a Live View remote problem...

  I use the remote software a lot and started having a problem in Live Mode when connected to the laptop...

  If I am connected there is no problem, but when I go to Live View to see what the camera sees it running a little and then give a "Connection Lost" error and close the software... You can't restart it unless you unplug the USB cable and plug it into the back...  Then, you can restart the software and all works fine... but when switching back to see live can run from any where between 1 second and 20 minutes without any problem, then "lost connection" and the software will stop...  I tried several cables, Reloaded the software and made sure Batteies are reloaded...  I had the camera for a year and a half and it has just started in the last month...   Before I could leave in direct mode until the battery pack came out with such a failure...

  Hi Quantummist,

  I recommend that you contact us for assistance with this.

• MXI-4, Manager of configuration problems and data base, clean install MAX

  Hello

  I have a problem with the MXI-4 kit / PCI-8331

  -C' is a clean install of MAX, using the default installation option.

  -Win XP 32. The PCI-8331 is the only PCI site in PC

  With the GUI of MAX does not, plug-and-play detects the jury.

  If I reboot, connect 8336 PXI and an another Council PXI (6641) in PXI basket, it's OK by PnP display.

  But as soon as I open MAX and expand the tree view of the devices, the Configuration Manager stops.

  I ge the message 'to NOR-PAL service Manager has encounterd a problem and needs to close' and 'MAX expired in the meantime a driver. "

  -J' have removed everything, reinstalled MAX, but the problem remains the same.

  -J' deleted configuration in C:\Documents and Settings\All Users\Application Data\National Instruments\MAX\Data Dictionaries\Last

  -I see a number of DLLs being re-written there, when I restart MAX, however there is no file config3.max (retrieved the entire disk) as suggested elsewhere.

  -It seems that if I only have the PCI card installed, I still have the same problem.

  I'd like to find if there is a problem with the hardware of the Board of Directors, the BIOS or the installation of MAX?

  Thank you

  Partially solved.

  The PCI-8331 seems to work in another PC, equipped with a newer BIOS.

  Could not test with MXI-8336 a hanging basket, as it is in a different location.

  Uptdating the BIOS of the computer 'defective' did not help, it seems like a new computer/motherboard is necessary.

• X 230 win 8.1 power management device driver problem

  Hello

  Cool win 8 build in place upgrade to 8.1. Then all the tools Lenovo update and latest Lenovo compatibility package installed.

  This device is not properly detected. I think it's a driver problem Power Manager (based on an old post with the same problem, but no resolution posted).

  Lenovo X 230

  Type: 2330-A59

  Device instance path: ACPI\LEN0078\5 & 2890D 699 & 0

  Location: On the controller shipped compatible ACPI Microsoft

  I tried the typical removal of the device and re - run the PM (Lenovo.com last) driver installation package. No change. The device is listed back in the device as an "Unknown" Device Manager

  Everyone there knows the solution? I hope it's something that I'm a little more research.

  JIM

  Found the answer. It is NOT the PM Driver.

  Lenovo HID HW Radio Driver for Windows 8.1 (32-bit, 64-bit), 8 (32-bit, 64-bit) - ThinkPad ... Learn more

• Cannot run any application system as anything in the administration tools, network and sharing Center, Device Manager. No problem running the applications Office, IE, etc.

  Vista Ultimate, 32-bit, SP2 had worked perfectly for two months. Machine set up to now and when started the first time, no network connection and my video wallpaper stops with an error message that says to reboot. The 2nd restart, I get internet connectivity, no wallpaper at all and no access to system applications that are listed in the title line.

  I can open Documents and navigate around, click computer and see the disks, etc., right click on computer and view the properties, but it shows no RAM and processor. If I click on Device Manager on this window, it crashes just forever unless I have kill with Task Manager.

  I had Windows Live Onecare on this machine and it expired during the period, it was closed. No problem... I plan to install MSE.

  Originally, I installed a smaller version of Vista of CD (still have it) but upgraded to Ultimate online and is not a product for this upgrade CD.

  I need to know where to start on fixing Vista so that it works correctly.

  Thank you.

  Hello

  ·        Where you upgrade the system for full vista?

  It is better that you have the Vista Ultimate DVD, so I suggest you ask the DVD from the dealer.

  I suggest you to check in the Event Viewer logs and let us know the exact error.

  Open event viewer

  http://Windows.Microsoft.com/en-us/Windows-Vista/open-Event-Viewer

  Method 1:

  I suggest you to do a scan of the SFC. File system (CFS) Auditor verifies that all Windows 7 system files are where they should be as they are by default and not corrupted, changed or damaged.

  a. Click Start, click principally made programs, accessories, right-click on command prompt and select run as administrator.

  b. click on continue or provide administrator credentials if prompted.

  c. in the type in the following command prompt window and press ENTER:

  d. sfc/scannow

  e. you should see the following message on the screen:

  § Begin the analysis of the system. This process will take time.

  § Beginning verification phase of system scan.

  f. % verification complete.

  g. once the scan is complete, a test to see if the problem you are experiencing is resolved or not.

  For more information, see the article mentioned below.

  http://support.Microsoft.com/kb/929833

  Thanks and regards.

  Thahaseena M
  Microsoft Answers Support Engineer.
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Remote - problem with full screen desktop

  I use Win 7 for a few months now, and the user experience is great!

  Remote Desktop software update is large but with a very annoying problem that I am facing.
  I use this to access my PC on my home LAN. I left once his mode full screen I need a windowed mode to work, but since I was not able to return to full screen. I tried to restart the sessions remotely, Resart the two PCs, delete the information identification, but in vain.

  Kindly help to solve the problem, because it is very annoying to use the session remotely in windowed mode, navigate and go down each time to access the taskbar and the address bar!

  Thank you.

  Hello
   
  Follow these steps and check whether the problem is resolved.
   
  Method 1:
   
  -Start "Remote Desktop connection".
  -Click on 'Options '.
  -Click the "View" tab
  -On "Display Configuration" settings, you can change the display of "Remote Desktop connection" by moving the slider of "small to large.
  -By moving the "slider" all the way to large, the display settings will automatically set in 'full screen '.
   
  Method 2:
   
  You can try CTRL-ALT & Break to return to the screen in full-screen.
  For more information about the remote desktop connection it see below section of Windows Help.
   
  Remote Desktop connection: frequently asked questions
  http://Windows.Microsoft.com/en-us/Windows7/Remote-Desktop-connection-frequently-asked-questions

  Thank you, and in what concerns:
  I. Suuresh Kumar-Microsoft Support.
  Visit our Microsoft answers feedback Forumand let us know what you think.

• ACS Appliance Agent remote problem

  Hello

  We have depending you on the situation:

  -2 x ACS SE

  -2 x ACS Agents on member servers remotely

  -2 x ASA

  We would like to authenticate the VPN users connecting to the ASA via the ACS and active directory.

  I have configured the remote agent following this link:

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/3.3/installation/guide/remote_agent/Rawi.html#wp289426

  But we are not able to pick up groups active directory to the AEC gui--> user external database > database group mappings > Active Directory > new Configuration.

  On the domain controller, we get the error ID 1030 and 1058, someone had these problems too?

  Thanks in advance and best regards

  Dominic

  Most likely, this is a Permission problem. What OS and SP you use.

  Have you tried to run the remote agent by using the LOCAL account instead of the service account that you created?

  Kind regards

  ~ JG

  Note the useful messages

• Features of the power manager and other problems associated with the T510

  For the better part of 5 years, I was a happy user of an IBM Z60m and decided it was time to move my z60 to my son and buy a new T510.  Well, I have after several weeks of property I can honestly say I'm irritated and frustrated by several current issues and I'm ready to send back all.

  Starting from the moment I pulled it out of the box I was having problems of power management.  I was on Microsoft help forums, called the lenovo support and spent countless hours on blogs and forums looking for help.   No matter what I do in the put lenovo on arrangements to take away my computer goes to stanby after one minute of inactivity and then wonder my windows password.  After a full day to insert my password my frustration level is off the chart.  I removed the password in the settings of the user who has not helped.  I changed the global settings to disable password in stanby mode which did not help.  I changed the function to optimize power and others, but none of it helped.

  Beyond these problems... I inserted two different discs to insert new programs and my system kept telling me that he did not read either.  I first thought they were zero but my old laptop ibm read without problem.

  So there you have it.

  Are you sure that the system is set the mode after 1 minute?  Or is the screen is locked?

  Try this:

  1. right click on the desktop and choose "Customize".

  2. click on "screen saver" in the lower right corner

  3. uncheck the box that says "On Resume, the logon screen"

  Which solves your problem?

• Tag Google Manager cause layout problems

  Hello!

  I'm almost done with my website, and I added the code of Google tag on the site manager. But for some reason, this time the code is really mess up my layout. The code itself is some photos and my Gallery completely disappear when I previews and when I publish. When I remove the code, the problem goes away. Does anyone has any advice for me?

  Thank you!

  It sounds like you have not closed it out of the code snippet. Check the code you pasted and make sure that it has a right to tag at the end.

  David

  Creative muse

• On VMware Service Manager 9 parameter problem

  Hi guys,.

  I have vCD1.51 to build a few days ago, and I would like to integrate VSM9 vCD.

  I am facing a problem, I downloaded it as the graph.

  I tried to enter vCD UserID and password, but I still can't get. He always the failure of authencation pop-up windows.

  Who can tell me what I should input in the field ID and password or is something wrong?

  

  Sincerely

  Rocky

  Hey Rocky,.

  It is really good news that finally you understood the question and he got resloved. Now enjoy the service manager magic!

  Kind regards

  MG