Masking problem

Similar Questions

• Animated mask problem

  So after a few tutorials on the animation timeline masks I had seen, I thought I had done everything to plan.
  
  I placed a picture in a layer that has been set as a mask, and all images of this layer mask with a new keyframe, I added that extra bit more of a graph (using the Brush tool), to slowly reveal the image.
  
  But nothing happens.
  
  Can someone take a quick look at the next FLA and see what might be up?
  
  [url] http://www.simobile.com/mask-problem.fla [url]

  You placed the object drawn into the layer of nask. Replace these with Forms.
  Deselect the icon in the toolpanel (Sqare with a circle on the inside, which is drawing object) and draw shapes in the layer mask.

• Mask problem Switch SG300-28 30

  I seem to have a problem using a 30 mask my SG300-28 switch L3 mode.  I want to isolate my router in one VLAN separated.  I had one VLAN created with a 24 mask and it seems to work.  I tried to change the mask on the switch and the router at 30.  There is no DHCP on this VLAN.  I cannot ping either side of the switch or router.  In the configuration screen to assign the IP address to the VLAN there you can use a mask from 8 to 30.  When I change the 30 to a 24, it works very well.

  I use a configuration access port for VLAN router.

  Using a VLAN and an access port is perfectly fine.  There should be nothing wrong with that.

  I don't know if this switch supports, but you might be able to do a "no switchport" and then put the IP address on the interface.

• Select and mask | Problems with the selection in the process of disappearance - CC 2015.5

  Hi all!

  I've just updated Photoshop 2015.5 CC version.

  I am currently working on a design that needs cutting contours.

  So I picked all the areas belonging to the background of the image and then click on the "select and mask" to refine the edges and then clear my selection as I usually did.

  But instead, my selection disappeared...

  My steps were:

  1. Selection of the areas to clear with "themagic wand tool.
  2. Click on 'select and mask' (output parameters: output to the selection).
  3. Click on 'OK'.
  4. Selection has disappeared!

  I have provided all the tools to their default settings, but nothing has changed.

  I tried to close and reopen the case, repeat the steps to delete the background, but I always feel the question.

  It is a big problem for me!

  I hope that there is someone who could help me/us with this!

  Best,

  Joanna

  I actually asked the new workspace me first thing after update, because I wasn't getting.  It's different enough that you need to learn everywhere, I'm afraid, but it is definitely an improvement when you become familiar with it.  See Julianne Kost guide below, but I suspect that you may need to adjust the sliders that control the opacity of the background.  Or simply click on the transparent part to start the selection.

  

  Select and mask "Julieanne Kost's Blog

• Layer mask problem

  Somehow, I've changed a setting that has now caused me problems with my layer mask. When I add a layer, then make a blurr Gaussian then to create a layer mask using the ALT key and clicking on the layer mask that my mask should appear in black. However, it doesn't. And I can't figure out how to change... or what to change to correct it. I'm a windows help using Photoshop CC. I do not know how to make the screen print see here since my photoshop so need advice on that a well... Can someone help me? Thank you very much! Kristy

  Your screenshot is confusing because you have either thumb nails disabled in the options panel, or you don't actually have a layer mask.

  

• Mask problem Photoshop CC

  Hello world

  I had a problem when I paint on the alpha channel. When I paint with a black color, the image is still slightly visible. All opacity settings are on 100%... It is really strange, I never get this before, I use PS for 10 years...

  What do you think?

  I don't understand, I have a few bugs with Photoshop CC. A lot of problem with layer with mask too. The mask to stay in the same place when I use the tool move... And the string is visible between the layer and mask...

  The previous PS are really better than the CC collection...

  Thank you.

  Gaétan Borneuf.

  FYI

  I'm Matt painter in the Visual effects industry.

  Windows 7

  HP Z800

  2 x XEON

  Quadro 4000

  24Go ram

  Have reset you your preferences?

  Win: Press and hold the keys Ctrl + Alt + Shift immediately after the launch of Photoshop starting. A box will appear asking if you want to continue with the reset, select 'yes '. If you don't see this, you're not fast enough... Try again.

  Mac: Hold down Cmd + Opt + shift and run Photoshop. A box will appear, asking you if you want to continue with the reset, select 'yes '.

• Clipping Mask problem

  Hey guys, I don't know what is happening, but every time I try to make a clipping mask, this inverted color problem happens. I have tried everything to fix it, but I can't find the problem. The image is colored and when I try to make a clipping mask, it turns into a reversed-ish stuff. I also tried havve invert ' the mask ', but it turns into B & w and not RGB.

  

  I can easily duplicaate your mistake

  

• WAG120N subnet mask problem

  Hello

  I have router WAG120N and I want to change the ip address of the local 10.1.X.Y computer and subnet mask of 255.255.248.0

  I changed the ip address but I couldn't change the subnet mask.

  Please help me...

  You can not. Linksys devices are mainstream devices and support only LAN 255.255.255.0 subnet or smaller. They consider that 254 IP addresses is sufficient for a consumer LAN.

• CS6 actions > batch saving of images in a clipping mask problem

  Hey all,.

  Been at this for a certain brand in now and searched the www thin suggestion - so really hope someone can help me here.

  Objective:

  -Target a folder with .gif xxx patterns (in the same size)
  -Configuration of batch stocks open each image in the folder, copy the image of the model individually more to one. PSD file which have a silhouette of the handle.
  -Apply the model on the clipping mask
  -Outside save as .png

  Question:
  So far, Ive had only automate > batch to save to a .png with the pattern correctly applied to the silhouette.

  I have experince, it's so close, I have everything down and start automate > batch then Photoshop will complain of not being able to locate the clipping mask.
  In my configuration of action I everything first open my .psd containing my form of sleeve, then open a real model image and then all the other steps ending with saving the .psd with a model in .png clipping mask.

  Just to give an idea on my setup take a look here:

  http://i.imgur.com/FE8mSEU.PNG

  In this case below, I've closed everything and run Automation > lots, which gives me the error that you can see here:
  http://i.imgur.com/7Cvj26D.PNG

  Any suggestions on what I could hurt OR if I do something wrong?

  Screenshot shows an Action that works for me in a batch.

  

• Refine mask problem

  I'm trying to improve you the mask and selections made based it, creating the mask, but it is not any adjustment of the mask.  If I try to use the RADIUS tool refine, or edge detection, it does nothing.   What I don't do. or hurt?  I followed the video tutorials on the Adobe support site.

  The image was originally a jpg that I converted to a PSD for editing, if it makes a difference.

  Are by clicking on the appropriate buttons in the toolbar. If you have the active left most key everything he will do it is create a new mask every time. I always use simply add and less buttons... unless I'm not kidding and hit another one some time!

  I hope this helps.

  Brad

• Mask problem

  Hello!

  I'm hiding a picture with a rectangle in a group container.

  This is the code:

  < s:Group id = "hide" >

  < s:Rect id = "rectCard" radiusX = "10" radiusY = "10" width = "247" height = "156" >

  < s:fill >

  < s:SolidColor color = "#AEDFE4" / >

  < / s:fill >

  < s:stroke >

  < color = weight of the '#ACBFC1' s:SolidColorStroke = '1' caps = "round" joints = "round" / >

  < / s:stroke >

  < / s:Rect >

  < / s:Group >

  < mx:Image id = "imgUserPic" width = "247" height = '156' maintainAspectRatio = "true" = "true" smoothBitmapContent = "true" scaleContent mask = "{mask}" / >

  The mask works, but I get a warning about data binding will not be able to detect assignments to hide.

  How can I fix this please?

  Hello

  Just change the id to something that is not a keyword, for example myMask or _mask

  David.

• movement satellite masking problem

  Hello!

  Ive got a file downloaded to all you, I can't seem to find a way for the satellite to be hidden behind the planet.although I think with MI of the motion on track, im stuck on the masking.

  any suggestions? Thank you

  Oh.  I don't see your satellite moving at all.

  Anyway, if you use the Tween in the timeline, you will use two interpolations.  a Tween to move your satellite before interpolation of planet and a 2nd to move your satellite behind your planet.  you won't use masking.

• gradient alpha mask problem

  Hello-

  I'm trying to create a gradient alpha mask for a PNG file, the effect being that of a gradual of thinking gradually in the background.  CS4 does not recognize alpha or transparent solid gradient gradient black white.  It uses the gradient as the mask.

  I searched and searched, but can't figure out how to make a simple gradient alpha of an image mask.

  Any help would be greatly appreciated.

  Thank you.

  Jesse

  Rasthaus for concept work.

  You need make the mask and maskee clips, give them instance names, set the cache as bitmap to the two true, then use bitmapcaching to make the mask work.

  I think pretty good directions are here: http://www.align.sk/blog/blog1.php/2008/10/23/transparent-masks-with-cacheasbitmap-as3

  For what it's worth, it's an enhancement request well known for this work when the author in addition to running with LIKE (I for one hope that we can add to it).

• masking problem: scrolling menu

  Hi, I have a drop down menu, but the image appears not when you preview. As suggested by others, I've changed the source of the image to png psd, jpeg, and none of those who worked. I also tried selecting TIME bitmap caching in the properties of the clip without success. someone at - it other advice? It works with flash 8 but not flash 9.
  Thank you!

  Nevermind, I answered my own question: the size of the imported image is larger than 8192 pixels wide which is apparently loading/memory problems.

• Depth of mask problem

  Have attached a movie to a depth of 50 and set it to hide, have animations and texts at higher depths by masking the mask is as well, do not know why this is happening
  
  Thank you

  This"refers to the timeline that contains your AddMask() Builder so you can expect everything on this timeline to hide.