"Mesa.dll is not found" from CVI 2010 installation

Similar Questions

• every time I try to load it from the DVD the error appears as: "the application could not be started because SPWIZENG.» DLL was not found. Reinstalling the application may fix this problem. »

  Original title: SPWIZENG.dll

  Hi, I got a cd of Windows 7 from my friend who is a software engineer so he gets all the programs (operating systems). It burned in a DVD instead of CD. So, every time I try to load from the DVD the error appears as:

  «The application failed to start because SPWIZENG.» DLL was not found. Reinstalling the application may fix this problem. »

  Then when I click ok, it says:

  The file 'Autorun.dll' could not be loaded or is corrupt. Setup cannot continue.

  Help, please. I'm not good with computers and I honestly don't know what to do.

  Thanks in advance,

  :)

  Hello

  Are you able to play or open other CD or DVD?

  Step 1: These error messages may be due to corrupted media. Try to use the same media on another computer and check if you are able to use it.

  Step 2: Search for the issue in the clean boot state.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:
  How to configure Windows XP to start in a "clean boot" State
  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:
  1. click on start and then click Run.
  2. type msconfig and click OK.

  The System Configuration Utility dialog box appears.

  3. click on the tab general, click Normal Startup - load all services and device drivers and then click OK.
  4. When prompted, click on restart to restart the computer.

  Similar problem: http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_install/windows-upgrade-windows-7-error-code-0x7e/b1bfbe8f-7980-4847-a186-2206e87c6bc4

• system failed because iertutil.dll was not found.

  When you start windows xp pro starts then stops and says this application has failed because iertutil.dll was not found.

  When you see a message like this:

  Explorer.EXE - unable to locate component: this application has failed to start because iertutil.dll was not found. Reinstalling the application may fix this problem.

  It is in the case Log:

  Event type: Information
  Event source: Application Popup
  Event category: no
  Event ID: 26
  Date: 18/02/2010
  Time: 08:38:48
  Description:
  Application popup: Explorer.exe - Unable to locate component: this application has failed to start because iertutil.dll was not found.  Reinstalling the application may fix this problem.

  The iertutil.dll file is required for explorer.exe at startup.  If explorer.exe is not able to run, you will not be able to do much with your system until the file is replaced.

  The file may have been deleted accidentally, malicious software could have deleted or your anti-malware software could have been quarantined it thinking it was a threat.

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  First of all, here are all the things you can 'try' which do not work:

  sfc/scannow

  The iertutil.dll is not one of the files that are protected by Windows File Protection, so it will not be replaced automatically if it's missing 3498.  This means that sfc/scannow won't help you.

  It is also not on your XP installation for you CD to copy or develop.

  You will have the same problem trying to start in any Safe Mode.

  You will not be able to run a browser on the system afflicted to go on Internet download one.  There is also a computer big security risk when downloading files from Internet sites anyway.

  You can still use the Task Manager to run the system restore and back, but I've never tried.

  If iertutil.dll is missing, you can copy from a system that works in the system afflicted with the same version of XP and Internet Explorer or sometimes copy one from another location on your system.

  You can get a good copy and put it on a floppy disk, thumb drive etc and copy it to your system plagued by using Manager tasks.

  When you see the error, you can click beyond it and eventually arrived at your screen background image where you can press CTRL-ALT-DEL to start Task Manager. TM you can click file, new task, browse and edit the menu drop-down "Files of type" to all files that you can see all the files in all the folders.

  Browse/navigate to c:\windows\system32 if iertutil.dll is really missing. If the error appears again while browsing, click OK to get past it.  The explorer.exe tries to run and cannot until the missing file is replaced.

  Then, still using the Task Manager, go to the c:\windows\system32\dllcache and see if there is a copy of the file.

  If this isn't in c:\windows\system32\dllcache, it is going to be elsewhere on your system and you will find another way.
  Start by looking in c:\windows\system32\dllcache.

  If it's the only thing missing, you can just copy the file to the c:\windows\system32\dllcache and paste it into c:\windows\system32 where it belongs.  If you don't, get one from a working system of the same type as yours, copy to a Flash DRIVE or a floppy disk and always using TM, browse, copy and paste it where it should be.

  TM, you can always access your thumb or other media same diskettes by navigation, copy, paste, etc. all work fine.

  You use TM to navigate to your thumb or floppy disk, copy the iertutil.dll good and then paste it in the c:\windows\system32 folder, where it is supposed to be.

  When go you there once again, your system may still be affected so no matter what you use for malware protection.
  follow these steps:

  Download, install, update and do a full scan with these free malware detection programs:

  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/

  It can be uninstalled later if you wish.

  Do not guess what the problem might be - understand and resolve it. I need YOUR voice and the points for helpful answers and propose responses. I'm saving for a pony!

• Hi I have a problem after installing my CS6.  He repeats to me that msvcr100.dll was not found

  Hi I have a problem after installing my CS6.  He keeps saying that msvcr100.dll was not found?

  Download the runtime MSVC 2010 from Microsoft and install it.

  Mylenium

• Tecra M9 - TPSMain.exe cannot start because CpePerf.dll was not found

  Hi and help,

  searched the Web and found other discussions of the forum with similar questions.
  Tried all suggestions, nothing worked. I'm not very good on the computer but you can find my way. In any case...

  After connection messge pop messages - up in succession, similar to: TPSMain.exe cannot start because CpePerf.dll was not found then: TPSoddctl.exe cannot start because CpuPerf.dll not found

  Computer works very well but Power Saver start is not automatic and can't select it from the Panel... "" Toshiba power saver does not work. "
  so select the power options... "could not start because the CpuPerf.dll is not running.
  Did all the research on the net and followed all the tips... i.e. unistall saving in safe mode, uninstall toshiba common utility can uninstall fatal error 0x7e

  Then download Ccleaner, inspections, uninstall with Ccleaner same fatal error.
  In support of Toshiba and tried to install Power Saver... same problem will not install.

  Thus help help help if possible.
  Computer works well but popping up messages are annoying and I'd love to sleep to extend battery.

  Tried the system restore, even though I doubt that it affects the files... Another problem "cannot complete system restore"... tried this several times and cannot restore the system either... What is happening?

  any help please
  Tim

  Hello

  I think you can solve this problem, recover the laptop.
  But that would mean that the whole HARD disk should be formatted and would be installed everything again, I put t know if this is an option for you

  It turns out that something will not with the Toshiba Power Saver installed and, consequently, the popup message.
  Usually new installation of GST should help. But it was not and I m wondering why

  Maybe this is s question really an OS since system restore help (to the previous state) didn t

  He s strange question right now I can suggest only a new recovery

• Error "this application has failed to start because normaliz.dll was not found. Reinstalling the application may fix this problem.

  Original title: error explorer.exe, Normaliz.dll is missing please help me about the issue.

  Hello

  I get the error "this application has failed to start because normaliz.dll was not found. Reinstalling the application may fix this problem"Please help me!

  Well - so much for the expertise of committed Microsoft Support Engineer 'experts', but no answer to what I expected.

  See how it works for you:

  If you see a message like this:

  Explorer.EXE - unable to locate component: this application has failed to start because Normaliz.dll was not found. Reinstalling the application may fix this problem.

  It is in the case Log:

  Event type: Information
  Event source: Application Popup
  Event category: no
  Event ID: 26
  Description:

  Application popup: Explorer.EXE - unable to locate component: this application has failed to start because Normaliz.dll was not found. Reinstalling the application may fix this problem.

  Start explorer.exe, but the normaliz.dll file.  If explorer.exe is not able to run, you will not be able to do much with your system until the replacement of normaliz.dll.

  You can click OK for errors and finished up in the Task Manager where you can try to fix it.  The message can keep popping up from time to time, while you're fixing it, so just click OK to close the message.

  If normaliz.dll is missing, you can copy it from a working system to the system afflicted with the same version of XP and Internet Explorer.

  You will get a good copy and put it on a floppy disk, thumb drive etc and copy it to your system plagued by using Manager tasks.

  The normaliz.dll file must be located in the c:\windows\system32 folder and therefore is not a Windows file protected, making the Microsoft Support Engineer 'experts' suggest running sfc/scannow, which is just another one of their prosecution of wild goose that will not work, he'll never work and it will only waste your time (and they don't tell you how to run either - if explorer.exe does not start).

  Then engaged Microsoft Support Engineer 'experts' will offer to you develop a copy of the file from the XP installation CD you probably haven't, but it is also not on your XP installation CD, and you will have the same problem try their suggestions to 'try' to start in any any Mode without failure, so this will not help you.  These "experts" seem to think that the Safe Mode boot or boot will replace magically missing files, but it doesn't.

  You also will be able to properly run a browser on the system afflicted to go on Internet download one.

  There is a large computer security risk in the normaliz.dll from some website download.  The best idea is to get a copy of normaliz.dll from another computer that has the same version of XP and IE and replace it from a USB device (which you can access from the Manager tasks), or using a system that works, you can download one of my SkyDrive.

  You can still use the Task Manager to run the system restore and bring it back, but I've never tried and never use SR in all cases.

  If you have recently done a bunch of Microsoft updates, you may have also gotten IE8 so maybe that something was wrong here although the normaliz.dll is the same for each version.

  When you see the error, you can click beyond it and eventually arrived at your screen background image where you can press CTRL-ALT-DEL to start Task Manager. TM, you can click file, new task, Browse and edit the menu drop-down "Files of type" to all files that you can see all the files in folders.

  Go to c:\windows\system32 to see if normaliz.dll is really missing. If the error appears again while browsing, just click OK to get past it.  The explorer.exe tries to run and cannot until the missing file is replaced.

  If it's the only thing missing, you can get one from a working system of the same type as yours, copy on a Flash DRIVE or a floppy disk and always using TM, to browse, copy and paste it where it should be or you can download one of my SkyDrive.

  TM, you can still access your thumb or any other medium the same disk by navigating, copy, paste, etc very well all work.  You use TM to navigate to your thumb or floppy disk, copy the normaliz.dll good and then paste it in the c:\windows\system32 folder, where it is supposed to be.

  If things get worse, just return to TM and remove the file back where you were in first place and continue troubleshooting.

  Using a system that works, you can also download a copy of the file from my SkyDrive and put it on a floppy or USB thumbdrive and networks diskettes for the distressed system.  Sandalenet means wear you the system afflicted by hand.

  I downloaded a copy of XP Pro SP3 file you need on my SkyDrive (everyone has a SkyDrive for file sharing).

  You can download it and when you do, place a copy of the file in these two folders (assuming that Windows is installed on your C drive):

  c:\Windows\System32

  Here is the link to my SkyDrive and you can get the file you need here:

  https://SkyDrive.live.com/?CID=6a7e789cab1d6f39&ID=6A7E789CAB1D6F39! 311

  When you see the files available for download, you can not see the file extension (.exe, .dll, .cpl, .sys, .zip, etc.), but when download you them they will have the right extension.

  When you download the file (especially if you use Internet Explorer), when you get a chance to save the file, your browser is unable to save the file with an extension (by example, .exe, .dll, .cpl, .sys, .zip, etc) then you will need to manually add the extension appropriate to the file when you download the file before you save it.

  You can download the file without the extension, and then rename the file to add the appropriate extension.  You do not want to use a file called normaliz when the name of the file should really be called normaliz.dll (if the downloaded file has no extension, you will need to change the name of the file to add the appropriate extension to make it work.

  You then put the downloaded files in the correct folders on your system.

  That may not solve all your problems, but at least you will be spending this part and we can then fix the rest.

• During the attempt to re - install the iTunes software, I got the Windows 126 error message. APSDaemon, exe-Unable to locate component. MSVCR.90.dll was not found. Re-installing may fix this problem

  I use Windows XP PRO Sp 3. I tried to open an iTunes download & got this message. "APSDaemon.exe that this application was able to start. Could not locate the component that msvcr.90.dll was not found. Re-installing may fix this problem. "
  All this happened after I tried to install a new update Apple iTunes. He kept saying that he could not install... I tried several different things to solve this problem, including doing a system restore in frustration, for 2 days before today... I tried to update iTunes, not always the case. Help, I'm a no techno, so please do not just refer me to somewhere else, I will never understand what I'm told to do, whenever I am sent somewhere else, I can't solve my problem & give up in frustration. Please can someone take pity on me & guide me through the fix?
  A related problem, I tried to run iTunes from the desktop, but I got was the Mini audio player.
  I just tried to recreate that & got again the error messages, the one listed above main & another one that says "iTunes is not installed correctly. Please re - install. Error 7 (Windows error 126).
  Whenever I try to re - install, I get the error again on the component .dll.
  I hope that's enough info to try & help me. I really need this fix to work as I have many meditations downloaded on iTunes, because Windows Media Player could not open the files.   It would take me hours & hours to find where they came, they were downloaded over 4 years!
  Thank you in advance.
  Sylvia

  If you have not had luck in iTunes (https://discussions.apple.com/community/itunes/itunes_for_windows?view=discussions#/?tagSet=1234) forum, uninstall and reinstall iTunes as described below:

  To perform a "clean" iTunes installation uses this technique proposed, from Support of Apple HT1926 article.  (If you are using Vista, see THIS instead).

  Go to control panel > Add/Remove programs
  Remove these applications in the following order (do not restart your computer if you are prompted during this process):

  1 iTunes
  2. Apple Software Update
  3. Apple Mobile Device Support
  4 Hello
  5 Apple Application Support (iTunes 9 or later)

  6. iPod for Windows (this may or may not exist, be it, it is not necessary, then we can remove it)

  7. iPod Updater

  8 QuickTime

  Open my computer > C: > Program Files
  Delete these files (if present)
  1 iPod
  2 iTunes
  3 QuickTime

  Follow these steps if the message "cannot delete iPodService.exe: it is used by another person or program" appears when you try to delete the folder of the iPod.

  1. Make sure that you have iTunes and iPod Update utility are not open.
  2. Press Ctrl-Alt-Delete.
  3. Select Start Task Manager.
  4. Click the processes tab.
  5. Locate the iPodService.exe in the list.
  6. IPodService.exe-click and choose end process.
  7. Quit Task Manager.

  Empty your temp directory:
  Open my computer > C: > Documents & Settings > username > Local Settings and delete the contents of the folder called "Temp".

  If you don't see the local settings, enable hidden files:
  Tools > Folder Options > view tab
  Select Show Hidden Files & folder, and then click OK

  Once this file is empty, restart the computer

  NOTE: If you have trouble uninstalling applications, or if you have a problem, reinstall iTunes because the installer complains that it can not uninstall the current version of iTunes, see the 'Installation issues' section below.

  Download & reinstall iTunes from here: http://www.apple.com/itunes/download/

  Installation problems

  There are several tools to deal with problems installing or uninstalling applications.  If you have these problems, the following should help.  Before using one of these tools (including #3), you must create a restore point from the system first (or back up the registry with C:\WINDOWS\ERUNT).  See http://windowsxp.mvps.org/registry.htm a complete disk image would be safer if you have this ability.

  1 Microsoft has a program install and the resolution of the problems of the uninstalling which is supposed to "work better" and be "safer" to use the old Install Cleanup Utility (3 below).

  2. free Revo Uninstaller.  You can also download a trial version of uninstaller Revo's ' Pro', which has a few more aggressive cleaning options, but this should not be necessary.

  3 Microsoft Windows Install Cleanup Utility.  Although this tool has been the preferred tool to deal with the problems of Windows Installer, Microsoft removed from Microsoft download servers because it seems sometimes deleted more than he was supposed to (I believe this was linked to Office uninstall).  You can still get Windows Installer Cleanup here--> http://majorgeeks.com/Windows_Installer_CleanUp_Utility_d4459.html utility

• Microsoft XP blue screen and message - this applicationhas failed to start because LSASRY.dll was not found, that reinstallation can correct moyenessentiel,

  no disc recovery... on a Panasonic Toughbook CF-50

  Let's see...

  If you see a message like this:

  Lsass.exe - Unable to locate component
  This application has failed to start because lsasrv WITH. DLL was not found.  Re-installing the application may fix this problem.

  Then, when you click OK, you have nothing more than a mobile mouse cursor.

  I seriously doubt that the opinion of the engineer of Microsoft Support for try the last good known Configuration will replace a missing file, so that theory approaches the area of ridicule.    This is not what LKGC, that is not what he does and is not how it works.

  Re-installation of XP is a very bad idea.

  There is also no need get a Windows XP installation CD, because you can create a bootable XP Recovery CD yourself and then see to replace the missing file.

  I understand not all next to a Microsoft representative.  Obviously not tested, won't work, won't help, but there are the necessary links to an article.   It's just another MSE wild-goose chase.

  The lsasrv.dll file should really never be missed, so answer these questions as the best yo can:

  Describe your current antivirus and software anti malware situation: McAfee, Symantec, Norton, Spybot, AVG, Avira!, MSE, Panda, Trend Micro, CA, Defender, ZoneAlarm, PC Tools, Comodo, etc..

  The question was preceded by a loss of power, aborted reboot or abnormal termination?  (this includes the plug pulling, buttons power, remove the battery, etc.)

  The afflicted system has a working CD/DVD (internal or external) drive?

  If the system works, what do you think might have changed since the last time it did not work properly?

  If you have no XP bootable media (or aren't sure you have) create a bootable XP Recovery CD of Console and do not forget what you have (no XP media required).

  This is not the same as recovery disks that might have come with the acquisition of the system store.

  You can make a bootable Recovery Console CD by downloading an ISO file and burn it to a CD.

  The ISO bootable image file you need to download is called:

  xp_rec_con. ISO

  Download the ISO from here:

  http://www.mediafire.com/?ueyyzfymmig

  Use a new CD and this simple and free program to burn your ISO file and create your bootable CD (do not install UniBlue or the Ask Toolbar - never!):

  http://www.ImgBurn.com/

  Here are some instructions for ImgBurn:

  http://Forum.ImgBurn.com/index.php?showtopic=61

  It would be a good idea to test your bootable CD on a computer running.

  You may need to adjust the computer BIOS settings to use the CD-ROM drive as the first device to boot instead of the hard drive.  These adjustments are made before Windows tries to load.  If you miss it, you will need to restart the system again.

  When you start on the CD, follow the instructions:

  Press any key to boot from CD...

  Installing Windows... going to pronounce.

  Press 'R' to enter the Recovery Console.

  Select the installation that you want to access (usually 1: C:\WINDOWS)

  You may be asked to enter the password (usually empty).

  You should be in the folder C:\WINDOWS.  It's the same as the

  C:\Windows folder that you see in Solution Explorer.

  The Recovery Console allows base as file commands: copy, rename, replace, delete, chkdsk, fixboot, fixmbr, cd, etc.

  For a list of the commands in the Recovery Console, type help at the prompt of commands or read on here XP Recovery Console:

  http://www.Microsoft.com/resources/documentation/Windows/XP/all/proddocs/en-us/recovery_console_cmds.mspx?mfr=true

  A good idea before you start things must first verify the integrity of your file system by using the chkdsk command.

  In the command prompt window, run the chkdsk command on the drive where Windows is installed to try to fix any problems on the afflicted player.

  Running chkdsk is fine, even if he finds no problem.  It won't hurt anything to run it.

  Assuming your boot drive is C, run the following command:

  CHKDSK C: /r

  Let chkdsk finish to correct the problems, he could find.

  It may take a long time for chkdsk complete or they seem to be "stuck".  Be patient.  If the HARD drive led blinks always, chkdsk is something.  Keep an eye on the amount of the percentage to be sure that it is still making progress.  It may even seem to go back sometime.

  You must run chkdsk/r again until it finds no error to correct.

  Then at the Recovery Console prompt enter orders to replace the missing file from backup copies that are already on your system:

  Copy c:\windows\system32\dllcache\lsasrv.dll c:\windows\system32

  Answered in the affirmative if invited to replace the existing file and then you should see a message that 1 file (s) has been copied.

  Depending on your system configuration, you may need to copy the files somewhere else, so if they are not in the folder dllcache for any reason, enter the command like this:

  Copy c:\windows\ServicePackFiles\i386\lsasrv.dll c:\windows\system32

  Answered in the affirmative if invited to replace the existing file and then you should see a message that 1 file (s) has been copied.

  Remove the CD and then type "exit" and restart your system.

• Error: mmc.exe - Unable to locate component. This application has failed to start because apphelp.dll was not found.

  Original title: this application has failed to start because apphelp.dll was not found.

  A window titled "mmc.exe - Unable to locate component" in the title bar, which includes the message:

  "This application has failed to start because apphelp.dll was not found.  Reinstalling the application may fix this problem. »

  that appears when you access many of the 'administration tools' in the start menu.  e.g. component, computer, event viewer Management Services, etc.

  I'm afraid I accidentally deleted apphelp.dll when cleaning on other files.  I found copies of apphelp.dll in following two tracks.

  AppHelp.dll C:\WINDOWS\$NtServicePackUninstall$ 124KO Extension Application 09/08/2004

  AppHelp.dll C:\WINDOWS\ServicePackFiles\i386 123KO Application Extension 04/13/2008

  I tried Recuva, but he could not find the file.

  How to re - install a such apphelp.dll suggested by the pop - up error message window?

  Thank you

  I thought it would be something that began with "A".

  For low overhead and free, think of Microsoft Security Essentials (MSE).

  MSE and a regularly good scan with the definitions updates using MBAM and SAS (from post above) should keep you in good shape according to your Internet habits.

• MSVCR80.dll was not found after installing an update for iTunes

  -5February2014 - yesterday I received an automatic update of iTunes (do not write update number) so I accepted the download automated and then with what I was doing on my PC.  Later in the process, a message said something about unable to download or install or something, so I cancelled the iTunes update, thinking I would look into another time.  This morning when I start my PC, as part of the service, I received a pop-up box that follows:

  "Unable to locate component APSDaemon.exe. This application has failed to start because MSVCR80.dll was not found. Reinstalling the application may fix this problem. »

  At this point, that I'm not sure that the application did not start OR should I try to install.  First of all, I restarted the PC, thinking it was just a ghost in the machine, but during and after the reboot issue I had the same error popup box.  Of course, this does not affect the ability to control Outlook, mail, or go on the Internet, but I'm afraid that someday when I need that MSVCR80.dll, I'm having a problem.  Can someone well tell me what I need to be concerned about or do to fix this "missing" file number, which is also be aggravated to the population of iTunes?  Thank you.

  Original title: MSVCR80.dll not found

  Hello

  Uninstall everything according to the instructions from Apple:

  «Remove and reinstall iTunes, QuickTime, and other software components for XP»

  http://support.Apple.com/kb/ht1925

  It is also the same list of what to remove what is in the link above from Apple:

  http://pcsupport.about.com/od/findbyerrormessage/a/MSVCR80-DLL-not-found-missing-error.htm

  Or try this program to remove it:

  http://www.revouninstaller.com/revo_uninstaller_free_download.html

  "Resolution of problems with iTunes for Windows Update"

  https://discussions.Apple.com/docs/doc-6562

  If the advice already given does not, please contact Apple for assistance.

  "Not to install iTunes or QuickTime for Windows"

  http://support.Apple.com/kb/HT1926

  "iTunes support-how to use iTunes.

  http://www.Apple.com/support/iTunes/

  "Contact iTunes Support.

  http://www.Apple.com/support/iTunes/contact/

  Or ask in the community Apple iTunes:

  https://discussions.Apple.com/community/iTunes

  See you soon.

• c:\windows\axutunag.dll is not found

  I get this message box when I start my laptop Windows XP 32-bit.  In the message "RUNDLL" box - 'c:\windows\axutunag.dll is not found.  What is the axutunag driver, and how can I fix this error?

  What is the axutunag driver, and how can I fix this error?

  axutunag.dll is not a system component that should be running everything from windows...

  If there is anything that touches on axutunag to system tray boot disable it...
  http://www.howtogeek.com/74523/how-to-disable-startup-programs-in-Windows/
  or

  You can use regedit... Press windows R, type regedit and click ok... (before you edit it, export the key you are going to change or remove)
  then navigate to these paths...

  [HKEY_CURRENT_USERSoftwareMicrosoftWindowsCurrentVersionRun]

  [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run]

  then look for the .dill file you have described here and delete this key...

• iertutil.dll was not found after trying to download internet explorer 8. I can't get into my computer. Not even the start screen.

  I can't get into my computer.  All I can get is the Task Manager.  It shows all my still intact material, I'm not him.  Not even to my home screen.  All that appears is my screensaver and a message saying to re - install iertutil. DLL... but how to do when I can't.

  Maybe someday, we will see again the proposal to:

  Once you open the Task Manager try the commands below.

  1. in the Task Manager, click file, and then click new task

  2. now type rstrui.exe and click OK

  This would launch the system restore on the computer refer the below Microsoft article more about the restoration of the system.

  If you really try , you would find that it does not work because rstrui.exe is unlikely that never will be in the PATH statement.

  If you want to launch the restoration of the system from the Task Manager, you will need to perform a new task like this:

  %SystemRoot%\System32\restore\rstrui.exe

  If c:\windows\system32\iertutil.dll is missing, you will see a message like this:

  Explorer.EXE - unable to locate component

  The application has failed to start because iertutil.dll was not found.  Re-installing the application may fix the problem.

  Because explorer.exe is not running, you will see only your background image /, but Ctrl-Alt-Delete will always bring up the Task Manager where you can maneuver around and replace the file.

  If the only problem with your system, it's that iertutil.dll is missing, you can replace the backup copy in the dllcache folder.  You can continue to obtain reviews iertutil.dll is absent, but just click OK for messages of recall as they pop up so you can continue working.

  One might think that you use the Task Manager, you can browse c:\windows\system32\dllcache and (after choosing to view all files) copy the iertutil.dll from there and then paste the iertutil.dll file in c:\windows\system32 where it belongs.  That actually works, but it seems that it does not work as you will get an hour glass stuck on the paste operation and perhaps wonder whether or not it has actually worked.

  To feel better replace the missing file, so you can actually see the file being copied and replaced... Task Manager, click file, new task and enter in the box (assuming that Windows is installed on your C drive):

  cmd

  Click OK to open a command prompt window and first make a copy of the original file (if it exists) by entering the following command:

  copy c:\windows\system32\iertutil.old c:\windows\system32\iertutil.dll

  That copies the file in progress if there is an and it will just complain if it is not a copy.

  We know that XP likes to keep the backup copies of critical system files in this folder:

  c:\Windows\System32\dllcache

  Knowing this, copy the backup copy of the missing file and replace the missing or suspicious file by using this command:

  Copy c:\windows\system32\dllcache\iertutil.dll c:\windows\system32

  Answered in the affirmative if invited to replace the existing file and then you should see a message that 1 file (s) has been copied.

  Type "exit" to close the command prompt window.

  Who will replace the missing or suspicious file and if that's all that's wrong with the system, Shut Down box Task Manager, you can choose to reboot your system and see how things are going.

  Do, or do not. There is no test.

  I decided to implement the points for a new puppy instead of a pony!

• This application has failed to start because uncdms.dll was not found. Reinstalling the application may fix this problem. How can I fix it? Kathy

  This application has failed to start because uncdms.dll was not found.  Reinstalling the application may fix this problem.  How can I fix it?  Kathy

  The above explains the problem, my problem is I don't know what it's etymology comes.  Is this windows software, or software from Microsoft or both?  What is the name of the Application?  Help, please!  Thank you, Kathy

  Hi Kathy,

  1 have you made changes to your computer recently?

  2. When you get this error message?

  The uncdms.dll file is associated with the Application of desktop search in Windows that is used to find and view an overview of the different types of files, such as documents, e-mail, photos and music files on a computer.

  I suggest you to follow the steps and check if it helps.

  Method 1: Uninstall and reinstall Windows Desktop Search

  The uncdms.dll file is installed on your PC when you download the Windows Desktop Search application. Problems with this application's files can cause a missing uncdms.dll of error appears on your system.

  To uninstall the Windows Desktop Search from your computer, you must complete the following two tasks:

  Step 1: Remove Windows Desktop Search from the boot sequence

  To do this, follow the steps below:

  a. click on the start menu, click Run.

  (b) in the Open box, type msconfig and press ENTER.

  c. in the System Configuration Utility dialog box, click the Startup tab.

  d. search and clear the check box for any option that is related to Windows Desktop Search or uncdms.dll.

  e. restart your computer.

  Step 2: Uninstall Windows Desktop Search applications

  To uninstall the Windows Desktop Search using the Add / Remove Programs, perform the following steps:

  a. click the start menu and select Control Panel utility.

  b. double-click the icon Add / Remove programs.

  c. in the Add / Remove Programs, locate and select the Windows Desktop Search.

  d. press the button Delete.

  e. restart your computer.

  Method 2: I suggest do you an online scan and check.

  http://www.Microsoft.com/security/scanner/en-us/default.aspx

  Note: The data files that are infected must be cleaned only by removing the file completely, which means that there is a risk of data loss.

• Error: ' ATL. DLL was not found"when trying to run any application.

  Original title: ATL. DLL was not found.

  I can't run applications in my pc someone in my house could not get into the computer and changed operating system to windows xp, which allows to be decommissioning of this t. Now, I get this message when I try to run an application: the application failed, because ATL DLL is not found, re - install the applicationmight solve the problem, but I get this message after you have re-installed and I don't know what else to do. Slow computer charges and freezing, something he has never done before. Same IE you have a problem, the only thing that works well, it is the remote assistant who helped me to get here and to him intermet, actually all of this with the dll thing started after I deleted the firefox browser because it froze the computer. Unable to restore my recovery utility, I tried a TI ran and told me it is impossible to get it back before I uninstalled firefox.

  Unfortunately, the support engineer technical 'expert' who is hired by the tips from Microsoft to run sfc/scannow will not help you.

  I would say that, as usual, the technical support engineer has not bothered to reproduce the problem and tried their own suggestion.

  If the atl.dll file is missing, sfc/scannow will launch but it does not work.

  It's just another wild goose chaseSupport Engineer.

  A lot of things will not work if the atl.dll file are missing.  System Restore will not work, Event Viewer do not work, you will not be able to get on the Internet, etc., until the file has been replaced.

  You try to run the system restore, you see the following message is displayed:

  Rstrui.exe - Unable to locate component
  The application has failed to start because ATL DLL not found.  Reinstalling the application may fix this problem.

  Try to open the event viewer, you see a message like this:

  MMC could not create the snap.
  MMC could not create the snap.  The snap-in may not be installed correctly.

  Name: Event Viewer
  CLSID: {975797FC-4E2A-11D0-B702-00C04FD8DBF7}

  Running sfc/scannow will be launched, but it will not run if the ATL DLL file is missing and you will see events like this in the event log (when you arrive, it works again):

  The server {8BC3F05E-D86B-11D0-A075-00C04FB68820} is not registered with DCOM within the required time.

  You can't get on the Internet using any browser.

  You have to somehow replace the missing or damaged file.

  The file might really be missing if he has been quarantined (actually deleted) by your antivirus not specified.  If the file is simply missing, you can just replace it and then later determine what happened to the file and decide what to do about this.

  You can search Windows on your system for ATL DLL and replace the missing file.

  THE ATL. DLL file must be in this folder (assuming that Windows is installed on your C drive):

  c:\Windows\System32

  Check and see if you can find the ATL DLL file in this folder, or if he's really missing, you will need to replace it:

  Depending on what applications you have installed, when you search for your ATL DLL system, you can find ATL DLL in several places on your system.  You must be sure get you the correct that belongs in c:\windows\system32.

  The most likely place to find a good copy of Atlant. DLL will be in one of these folders:

  c:\Windows\System32\dllcache
  c:\windows\system32\ServicePackFiles\i386

  Locate a copy of the correct Atlant. DLL from the file in one of these folders and copy/paste in the folder c:\windows\system32.

  Answered in the affirmative if invited to replace the existing file.

  There is a copy of the file on my SkyDrive, you can download a system not affiliated and then copy the file to a Flash DRIVE or a floppy disk and apply it on the afflicted system c:\windows\system32 folder.  Here's how:

  I downloaded a copy of XP Pro SP3 file you need on my SkyDrive (everyone has a SkyDrive for file sharing).

  You can download it and when you do, place a copy of the file in these two folders (assuming that Windows is installed on your C drive):

  c:\Windows\System32
  c:\Windows\System32\dllcache (this is where XP keeps backups of important files).

  Here is the link to my SkyDrive and you can get the file you need here:

  https://SkyDrive.live.com/?CID=6a7e789cab1d6f39&ID=6A7E789CAB1D6F39! 311

  When you see the files available for download, you can not see the file extension (.exe, .dll, .cpl, .sys, .zip, etc.), but when download you them they will have the right extension.

  When you download the file (especially if you use Internet Explorer), when you get a chance to save the file, your browser is unable to save the file with an extension (by example, .exe, .dll, .cpl, .sys, .zip, etc) then you will need to manually add the extension appropriate to the file when you download the file before you save it.

  You can download the file without the extension, and then rename the file to add the appropriate extension.  You do not want to use a file called atl when the name of the file should really be called atl.dll (if the downloaded file has no extension, you will need to change the name of the file to add the appropriate extension to make it work.

  You then put the downloaded files in the correct folders on your system.

• Whenever I turn on my computer, I get "Sqlite3.dll is not found."

  Original title: "Sqlite3.dll is not found."

  Whenever I turn on the computer. Once the desktop screen .it's a message "this application has failed to start because sqlite3.dll is not found. reinstalling the application may fix this problem".but the computer still can run that I don't know what was wrong and how can I fix this please?

  I'm not leaving your system works in selective startup mode, because that would leave you with a sloppy XP configuration.

  You must find the faulty startup item and get rid of it.

  Here's how:

  It is sometimes easy to get rid of the error message by doing something like disable the startup item in msconfig (if you can still find), but I suggest you fix the problem and difficulty not only the symptom of the problem by simply deleting the startup message.

  I would also not recommend you start digging in the registry to try to find the startup item and remove it unless you have a backup of your system or at least a backup of your registry, because there is no 'Cancel' or 'quit without saving changes' option in regedit.  If you make a mistake, that's all.

  These ideas relieve 'rapid' and sometimes risky of the symptom if they not even work at all, but they can't actually solve the problem.  Also, I'd be suspicious of ideas that begin with the words "try."  You don't need to try things, you need to fix things.  You don't need to try ideas that might work, you must do something that will always work all the time.

  Here are the detailed instructions that protect you and solve your problem in the 'right' way.

  There is very little. DLL files that should be loaded from the C:\WINDOWS folder and is not one of them.  If you do not have a good explanation for the name of the file in a Google search, the chances are good that your system is currently or has been infected by malware.
  A "Cannot find...". ', ' Failed to start..., "Could not load..." ». "Might not work... "" Cannot run ""error loading... ". "or"specific module could not be found"message at startup is usually related to the malware that has been configured to run at startup, but the referenced file has been removed after a malware scan, leaving behind him a startup item or the registry entry pointing to a file that does not exist.
  It might be a removal of malicious software or an application not installed.  The entry may have a curious looking name since it was probably generated at random when the malware was installed. If you search your system for the referenced file, you may not find.
  Windows attempts to load this file but cannot locate because the file has been deleted for most probably during an analysis of the malware. However, an orphaned associate of remainders of startup parameter or registry entry and tells Windows to load the file when you start or connection.
  So you should delete the referenced entry Windows stop trying to load or run the file. It may or may not be included in the registry, but you can find it.  Autoruns (see below) you get the elements no matter where it is.

  You must be sure to solve the problem and not just fix the symptom of the problem by simply relieving your message - system is not a fix (there is a difference).

  If you just locate and uncheck the item in msconfig, which disables the element but does not remove the reference to the element of false starting your computer.   The msconfig program is not a Startup Manager, that's a troubleshooting tool.  Disabling things in msconfig to put an end to the messages and think that your problem is solved is short-sighted and leave behind him a sloppy XP configuration.  Just disable the display of a start-up error message should not count as a 'solution' to the problem.
  If you are comfortable editing the registry, you can find and remove the reference directly from there or remove it using a popular third-party tool called Autoruns.  The problem can always be found in the registry well.
  Before making any changes to your registry by hand or with third-party tools, don't forget to first make a backup of the registry
  . There is no cancellation or exit without saving the option in regedit.
  Here is a link to a popular registry backup tool:
  http://www.SnapFiles.com/get/ERUNT.html
  You can also use the Autoruns to find the element of start remains little matter where he's hiding.  Autoruns does not install anything on your computer.  It will display all startup locations where the reference may be then you can turn it off or remove it completely.  Here is the download link for Autoruns:
  http://TechNet.Microsoft.com/en-us/sysinternals/bb963902.aspx
  Run Autoruns.exe and wait that he at the end of the filling of the list of entries.
  When the Autoruns is finished scanning your system, it will say "Ready" in the lower left corner. Autoruns can be a little intimidating to first if you have never seen it before because it displays a lot of information.  You are really interested only a few sections.
  The problem is usually to start the system or the user startup entries, then click the connection tab and see if the startup item is there.
  Scroll through the list and look for a boot entry associated files in the error message.
  If you can't find on the connection tab, look in any tab.
  You can also click file, search to search for logon, or any tab for all or part of the name of the element.
  Right-click on the offending entry and choose Remove.  If you are not sure what it is, you can simply turn off (uncheck the entry), reboot, and if the problem is resolved and things work normally and everything works fine, then delete the offending entry.  If you don't see it in Autoruns, you may edit the registry and remove the item from your startup folder it.  Autoruns shall display the same information however.
  Given that your system has or has had an infection, follow up with this:
  Perform scans for malware, and then fix any problems:
  
  No matter what you use for malware protection, follow these steps:

  Download, install, update and do a full scan with these free malware detection programs at:
  Malwarebytes (MMFA): http://malwarebytes.org/
  SUPERAntiSpyware: (SAS): http://www.superantispyware.com/
  They can be uninstalled later if you wish.

  In 1985, there were 11 known computer viruses.  Today, there are over 70,000 and new threats are detected every day.  Always update your virus definitions before running a scan.

  Restart your computer and solve the outstanding issues.