My HP desktop computer can not find my router wireless already in line with the other 2 computers. Help?
Vista HP Desktop shows cable with a new Linksys E1200 as connected to 'Unidentified network', 'Local' only without an internet connection. Same computer, same Ethernet cable connected directly to the ISP modem works fine. Router has been implemented by drive and works very well for a 2nd office direct by cable and wireless laptop.
Use exhausted with Cisco and they believe that there may be configuration problems they can not help me solve. Map network shows "works correctly. With current Ipv4 set to auto configure I get very little connectivity at startup until the weather window says service not available.
Can someone help me to get these two talking?
Hi FrankeyeAm,
· Did you do changes on the computer before the show?
· You get the error message?
Follow these methods.
Method 1: Temporarily disable the security software.
Disable the anti-virus software
http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software
Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.
Method 2: Follow these steps:
Step 1: Start the computer in safe mode with network and check if the problem persists.
Startup options (including safe mode)
http://Windows.Microsoft.com/en-us/Windows-Vista/advanced-startup-options-including-safe-mode
Step 2: If the problem does not persist in safe mode with networking, perform a clean boot to see if there is a software conflict as the clean boot helps eliminate software conflicts.
Note: After completing the steps in the clean boot troubleshooting, follow the link step 7 to return the computer to a Normal startupmode.
Method 3: Follow the steps in the article.
Windows wireless and wired network connection problems
How to reset the Protocol Internet (TCP/IP)
http://support.Microsoft.com/kb/299357
Tags: Windows
Similar Questions
-
Why my computer can not find windows Defender?
Why my computer can not find windows Defender?
Hello
read this information on the Defender:
· If you use microsoft security essentials avg avira mcafee norton etc they disable the vista version of windows defender by default
the basics of Microsoft security has its own version of windows defender
and other anti-virus programs use their own particular type of application to scan for spyware and malware
It of nothing to worry and is the default action, which is designed for them to do
If the above does not apply to your machine to read the information on the below link on how to disable the windows defender service in vista or make an autostart to enable
and here is the method to remove it from startup in vista
http://www.groovypost.com/HOWTO/Microsoft/Vista/remove-Windows-Defender-from-Vista-system-startup/
and this is how you would normally activate or disable windows defender in vista from within defenders of own and options tools
http://www.groovypost.com/HOWTO/Microsoft/Vista/disable-Windows-Defender-for-Microsoft-Vista/
and read this information to microsoft:
Error message when you run Windows Defender: «Error 0x800106ba»
http://support.Microsoft.com/kb/931849
and if you need to change startup programs read this information on the other methods of doing it without using defender
using msconfig read this tutorial;
How to use MSCONFIG in Windows Vista
Here's how to use MSCONFIG in Windows Vista to disable some unnecessary programs that load automatically at startup
http://netsquirrel.com/Msconfig/msconfig_vista.html
and also try this program;
This utility, which has a knowledge of auto-starting locations of any startup monitor, shows you what programs configured to run at system startup or login and that the entries in the order of processing windows. These programs include those in your startup folder, Run, RunOnce, and other registry keys. You can configure Autoruns to show other locations, including Explorer shell, toolbar extensions, helper objects to the browser, Winlogon notifications, auto and many start-up services more
-
I accidentally buy the windows version of adobe acrobat DC instead of the mac version I only a mac computer can you please cancel my purchase and replace it with the version of windows with a mac version. the order number is AD006058877NL. Rgds, jan van montfort + 31681471049. [email protected]
Hi Jan,
I understand your concern, please see this doc on this subject: return, cancel or change an Adobe order
Kind regards
Rahul
-
It does not find my computer out of no where just stopped after wifi wifi and I can't find to make it. I went in the search bar and type "cmd" and then the command bar that I wrote "ping 127.0.0.1, then he replyed 4 times" reply from 127.0.0.1: bytes = 32 time»»<1ms ttl="128" i="" dont="" no="" what="" to="" do="" now="" to="" fix="" my="">1ms>
Hello
1. what exactly happens when you try to connect to the Internet through wireless?
2. you get any error message?
3. what operating system is installed on the computer?
4. don't you make changes to the computer until the problem occurred?
I suggest you to try the steps below and check if it helps.
Wi - Fi and in Windows network connection issues:
http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-WindowsHope this information is useful.
-
The desktop icon can not find the program
I'm having a problem where when I click on my desktop icons they can not find the program that is associated with run.
Most of them is related to sites Web that I often use, so I select Internet Explorer as the associated program then remember this radio button, but when I connect and get back in that I get the same error.
I am running windows XP, I say this because I've posted this before, and I referred to a difficulty which will not work with this operating system.
Any help would be appreciated.
Hello JoseVasquez,
Try the automatic solution of the following article:
Article ID: 307859 - how to change or choose which program starts when you double-click a file in Windows XP
http://support.Microsoft.com/kb/307859This should help to restore default associations in Windows XP.Thank you
Marilyn
-
Deinstitutionalized drive, my computer can not find the music stored on the internal drive
I was recently released from the balance of PAYMENTS (Bureau of Prisons), and I gladly paid $25 for the reader deinstitutionalized. I got it in the mail and I am very happy with the improvements, however, when I plug it into the computer, the computer cannot find the music that I invested a lot of money. The drive works fine. I can listen to all the songs that are on it, but I can't find them with all software, including the software downloaded from Sansa. When I click on the player, in any program/browser, I get the same thing: the folders that are empty. It saves space, but sees ALL files. Many of the albums available at the bottom of the PYRAMID were incomplete and I want to "fill the gaps", but can not find the whites to fill. Any help would be wonderful. I paid my $95 (for the player AND have unlocked it) MORE about $1400 in the songs, so it's a pretty big deal for me to get access... Thanks in advance.
My guess is, it is a question of USB MSC - MTP mode.
Your drive may be connected to your computer in the title of one of the 2 separate USB MSC or MTP modes. This is located under settings of the player. (There is a 3rd option it, auto-detection, trying to connect under MTP mode but then fold in MSC mode, if necessary.) Is the reason why it's important, files transferred to the Clip under a mode USB can only be seen by your computer when the computer is under this same mode. And so, for example, if the songs are put on the player mode USB MSC, if you connect later under MTP mode, the computer will not see these files. If you have set the player to one of the USB modes and always use this mode (MSC mode is the least problematic, in virtue of which the player is considered to be a USB key; however, MTP mode is necessary for files protected by DRM), you're fine. If, however, you change mode, emits a "invisibility". And if you're ready auto detection, the computer can change the modes on you without you knowing.
And thus, better Board: turn on the player (recommended) MSC or MTP mode and stay there and stay away auto detection setting.
And if you have been on a mode but want to switch to the other and to be able to see all of your files on your computer, set the player to the previous mode, transfer your music to your computer and delete them from the player, re - set the player to new USB mode and transfer the songs back.
-
I bought the College picture for my other computer, no problem, I tried to do the same thing with yhis computer can't find it. I went where it should be, but it isn't here.
Hello, Dorian,
If you have downloaded in Internet Explorer, go to tools, click View downloads, and you'll see the directory where it has been downloaded. Not visible? Look down, in the bottom left of the word 'options', click on this and it will display the current default folder for downloads, but after writing it down, you can change it to any folder of your choice (mine is C:\__Downloads - always watch first!).
If you use another browser, go to this toolbar for browsers and search for the download folder and display it. You should find similar settings for the other locations.
Let me know if this solves the problem for you.
Kind regards
BearPup
-
computer can not find the recovery disk
I have a notebook G72-B54NR, I had my computer reset. When I tried to reinstall windows 7 with the 2 recovery discs, I get a message saying that this computer has not detected a recovery disk. Thank you.
Are you at the end of the process here:
-
Computer can not find scanner Canon pixma mg2550 printer
Ive perchased today that precedes, but my computer won't find.
installed and run the installation disc.
no site ive found don't yet recognize this printer.
my previous hp printer was not a problem.
the only thing I mentioned, is the drive of dvd/cd said: 0 bytes to the left of 450?
can someone help please...
Moved from Community Participation
Original title: canon pixma mg2550 printer scanner
Contact Canon support through their website to see if they can help.
-
Computer can not find a driver for my iPhone?
Original title: Bluetooth
My bluetooth device recognized my iPhone but does not connect because the computer cannot find a driver, where can I find the driver I need?
Hello
· What operating system do you use?
· What iPhone version do you use?
· You have installed the iTunes software on your computer?
See the link below and check if it helps:
http://support.Apple.com/kb/ts1538
For further assistance, contact Apple support.
-
I'm not the original owner of my computer. Those who had before me thought it was a technical genius and probably tried to fix things that were broken. When you try to defrag my computer I get the message "Windows cannot find 'C:\Windows\System32\dfrgui.exe'. I also had the problem when you try to activate the features in option with the message "Windows cannot find 'C:Windows\System32\OptionalFeatures.exe'. I don't know that there is more stuff like that... anyway, does anyone know if there is what I can do about it? I tried to open prompt as administrator and type sfc/scannow and it gets to 31% and I get the message "Windows Resource Protection could not perform the requested operation".
Hello
read the below tutorial on how to perform a repair installation
http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html
____________________________________________________
or, as it is a second hand machine;
Here are the different ways to reinstall Vista
Contact the manufacturer of the laptop computer and ask them to send you to vista recovery disks to reinstall the operating system back as it was when you bought it
they do it for a nominal cost of $
also ask them if you have a recovery partition on your hard drive to get back to the way you bought
you would normally press F8, F9, F10 or F11 or Alt + F10 or 0 to start to start the recovery process according to the manufacturer
Ask them of the exact key sequence
or borrow a vista microsoft dvd; not a HP, Acer recovery disk etc
Make sure that you borrow the correct 32-bit or 64-bit microsoft dvd to your computer
they contain all versions of vista
This is the product key that determines which version of vista is installed
http://www.theeldergeek.com/Vista/vista_clean_installation.html
How to replace Microsoft software or hardware, order service packs and replace product manuals
-
I am trying to connect my mobile phone (sanyo) to my computer / but computer says it can't find the driver? How can I fix it? I'm new on this and try to get the photos on ebay and craigslist. Thanks for any help.
Most often when a device does not work, it's because the driver has been corrupted.
Try reinstalling your.
http://Windows.Microsoft.com/en-us/Windows7/update-a-driver-for-hardware-that-isn ' t-work correctly? SignedIn = 1
http://captaindbg.com/how-to-update-drivers-on-Windows-7/
-
Computer can not find the wireless (bluetooth) jam speaker
I downloaded Rocketflish micro bluetooth adapter with driver. Computer still cannot find JAM wireless. Computer is HP less than a year. Did not come with bluetooth. All suggeswtions... I have disenabled speakers realtek
Bonnie
Moved from feedback
Original title: device is pregnant jam wireless
Hello
If your laptop does not have Bluetooth built in, it is possible to install Bluetooth connectivity using an external Bluetooth USB adapter.
If you have not, look here
Add a Bluetooth device to your computer
http://Windows.Microsoft.com/is-is/Windows7/add-a-Bluetooth-enabled-device-to-your-computer
-
computer can not find cd drive evan disks when a disc is in the drive?
When I turn the pc on the drive makes a funny noise? (hard drive), I put dvd burn program when ready to burn on the disc, then you request to insert the disc that is already underway in that it does not find any disk I put
Hello
If below does not fix it you may have a faulty drive
Try the microsoft 'fix - it' for your problem below
http://support.Microsoft.com/mats/cd_dvd_drive_problems/en-us
and read this information too
-
Computer can't find a printer Wireless Signal
My computer is connected to our wireless network, but can't find the printer wireless also connected to the network. Here are some of my info. Someone has ideas of how to do to solve this problem?
Windows IP configuration
Name of the host...: work
Primary Dns suffix...:
Node... type: broadcast
Active... IP routing: No.
Active... proxy WINS: No.
... DNS suffix search list: hsd1.tx.comcast.net
Local Area Connection wireless LAN adapter * 13:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Microsoft Wi - Fi Direct map virtual #2
Physical address.... : 26-DB-30-DA-26-50
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Local Area Connection wireless LAN adapter * 2:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
... Description: Microsoft Wi - Fi Direct virtual card
Physical address.... : 16-DB-30-DA-26-50
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Ethernet Ethernet adapter:
State of the media...: Media disconnected
The connection-specific DNS suffix. :
Description...: Realtek PCIe FE Family Controller
Physical address.... : F0-92-1C-EC-91-E9
DHCP active...: Yes
Autoconfiguration enabled...: Yes
Wi - Fi wireless LAN adapter:
The connection-specific DNS suffix. : hsd1.tx.comcast.net
... Description: AR9485 Qualcomm-Atheros 802.11b/g/n WiFi adapt
Physical address.... : A4-DB-30-DA-26-50
DHCP active...: Yes
Autoconfiguration enabled...: Yes
IPv6 address: 2601:e:2880:4000:1f62 (Preferred)
Lease obtained...: Thursday, March 19, 2015 11:56:09
End of the lease...: Monday, March 30, 2015 09:55:28
IPv6 address: 2601:e:2880:4000:b802:91 has 6:701 b: 7419 (Preferred)
Temporary IPv6 address...: 2601:e:2880:4000:60ac:66ac:9534:45c1 (Preferred)
Temporary IPv6 address...: 2601:e:2880:4000:bc50:2d9a:18fc:a414 (Deprecated)
Temporary IPv6 address...: 2601:e:2880:4000:d150:f11:21 has 9: cbd8 (Deprecated)
Address IPv6 local link...: fe80::b802:91 a 6:701 b: 7419 %3 (Preferred)
IPv4 address...: 10.1.10.58 (Preferred)
... Subnet mask: 255.255.255.0.
Lease obtained...: Thursday, March 19, 2015 11:56:08
End of the lease...: Tuesday, March 31, 2015 13:14:45
... Default gateway. : fe80::250:f1ff:fe80:0 3%
10.1.10.1
DHCP server...: 10.1.10.1.
DHCPv6 IOOKING...: 61135664
DHCPv6 DUID customer...: 00-01-00-01-1A-2C-70-2F-F0-92-1C-EC-91-E9
DNS servers: 2001:558:feed:2
2001:558:feed:1
75.75.76.76
75.75.75.75
NetBIOS over TCP/IP...: enabled
Tunnel adapter ISATAP.hsd1.TX.Comcast.NET:
State of the media...: Media disconnected
The connection-specific DNS suffix. : hsd1.tx.comcast.net
... Description: Microsoft ISATAP adapter
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
Card tunnel Teredo Tunneling Pseudo-Interface:
The connection-specific DNS suffix. :
... Description: Teredo Tunneling Pseudo-Interface
Physical address.... : 00-00-00-00-00-00-00-E0
DHCP active...: No.
Autoconfiguration enabled...: Yes
IPv6 address: 2001:0:9d38:6abd:3871:178f:9d37:3318 (Preferred)
Address IPv6 local link...: fe80::3871:178f:9d37:3318 %7 (Preferred)
... Default gateway. :
DHCPv6 IOOKING...: 335544320
DHCPv6 DUID customer...: 00-01-00-01-1A-2C-70-2F-F0-92-1C-EC-91-E9
NetBIOS over TCP/IP...: disabled
Hello
Thank you for the information.
I would like to inform you that we have a support forum dedicated to systems on area issues, I suggest you to send your query on Microsoft TechNet forum for this issue. You can get more effective suggestions and adapted by experts familiar with this topic.
Please visit the link below to find a community that will support what ask you:
Microsoft TechNet
https://social.technet.Microsoft.com/forums/Windows/en-us/home?Forum=w8itpronetworking
Hope the helps of information.
Please do not hesitate to answer, in the case where you are facing in the future other problems with Windows.
Thank you
Maybe you are looking for
-
When I downloaded the update of security today tabs began to appear and I don't want to do. I don't have that set in options, but he does it anyway. How can I fix it?
-
Are there plans to allow enforcement of the workout to add to the looks?
I use the app to drive regularly. I want to add to the looks so that I don't have to find it in the list of applications. It would be much easier. Why can't this app added to the looks? Also, is there more information about the application of the
-
Unable to locate "AVI compressor Comparison.vi.
Hello I use Labview 8.2.1 with NI Vision Acquisition 8.6 being installed (for the use of a card PCI-1428). Have tried to locate the VI mentioned, I can't not find anywhere. Indeed, taking a peek in the finder of the example, in the 'toolkits' and Mod
-
May not increase the value of data chart history but may decrease
Hello In my application, I use 3 cards. I have 250 Hz sampling frequency on my system and I want to display a different number of seconds on my paintings. By default, the chart history data have 1024 points, which is second ~4.1. Now the problem is,
-
power button will affect the performance of the system
Mr President. I was forced to use the power button to turn off my laptop HP 2231tx G6 in certain circumstances. I would like to know if this will affect all my gear system & impact on its performance. Because mine is only a new system.