My taskbar to desktop Windows Vista has flippedhttp

Similar Questions

• Desktop Window Manager has stopped working and was closed

  One of our machines (HP Pavilion dv7 Notebook PC running Windows Vista x 64) will receive the error "Desktop Window Manager has stopped working and was closed" with lots of close error. He reappears (as well as all windows flasher to non-aero, then back to aero) in a few minutes, spends about 5 times per hour.

  I did some research on this and have already taken the following measures without a bit of luck:

  1 run the command chkdsk / SFC scan - nothing found via chkdsk, SFC found some issues fixed, and some, it did not set. Them that it solves not all related to Windows Sidebar, which I do not / does not start.

  2. put updated drivers for ATI Radeon 3200HD - this had a lot of new questions. Installing caused newer drivers ATI catalyst to no longer work with errors during installation and popup errors at startup. After trying several solutions workaround to try to get installed it, I ended up coming back to the driver that came with the laptop, that are properly installed and working without error. I am skeptical of update of this stable driver as a solution to the dwm.exe error.

  3. this problem just started yesterday, that occur with not a lot of changes. Other than updates of windows (I think that .NET framework and a few other updates installed), I replaced NOD32 antivirus with Bitdefender antivirus. The system was stable with bitdefender for about 2 weeks, so I'm not convinced that this program is causing the error.

  4. the event viewer shows the following:

  Failing application Dwm.exe, version 6.0.6002.18005, time stamp 0x49e02696, failed module ntdll.dll, version 6.0.6002.18881, time stamp 0x51da3d16, exception code 0 x 80000003, offset 0x00000000000461f0, process id 0 x 124 error, start the application time 0x01cea0365a457adc.

  Offset, process id and start on time all vary, but there are a lot of these application errors in the viewer all screaming Dwm.exe like the failing application.

  What should be my next course of action?

  You do not receive an error but a caveat. NTStatus results (the set of codes execption used by ntdll - the failed module) begin to 0 for no error, 4 for information (you should never see this), 8 for putting guard and C for error.

  It's your specific error.

  //
  MessageId: STATUS_BREAKPOINT
  //
  MessageText:
  //
  EXCEPTION {}
  Breakpoint
  A breakpoint has been reached.
  //
  #define STATUS_BREAKPOINT ((NTSTATUS) 0x80000003L) / / winnt

  Problem is, you shouldn't have breakpoints. Breakpoints are set by debuggers and stop the execution of the program to the State of the program can be examined. There should be no breakpoints in a retail system. More breakpoints are inserted into memory during execution of the program in a debugger. They tend not to do in the actual file.

  So here are two assumptions, either you have no exit code, IE test code (driver?). Or you have a running program that behaves like a debugger (which is suspect).

  Each of the three towers of programs, services, and drivers in increasing amounts. So restrict the possible culprits.

  Clean boot

  Click Start - all programs - Accessories - run and type

   

  msconfig
  

   

  Then go to the Startup tab uncheck everything. Then go to the Services tab check hide all Microsoft Services and uncheck everything that is left.

   

  Reset. If this resolves your wake problem ½ of services / of startup items until you find that one.

  
  Tip clean boot

  If the above does not help.

  Download Autoruns http://technet.microsoft.com/en-us/sysinternals/bb963902.aspx

  Start the program by right-clicking and choosing run as administrator and click on the menu Options - Filter Options and check hide Microsoft entries and disable include the empty slots. Uncheck the box just to the left.

  Reset. If this resolves your wake problem half of the items until you find the one that.

  Safe mode

  If the above does not help.

  Click Start - all programs - Accessories - run and type
   

  msconfig
  

   
  Go to the Startup tab, and then click Start. Reset. Come back here and uncheck the box secure start to return to normal mode.

• continue to spread the message ' desktop window manager has stopped working and was closed ".

  continue to spread the message ' desktop window manager has stopped working and was closed ".

  The office then blinks and I can't use the Aero feature.

  Any correction or known issues?

  Thank you
  in2stocks

  Hello
  It is usually a video driver issue. Would like to know what controller you have and see if the manufacturer has a new driver for Vista.
  Please let us know if that was the issue.

  Mark <> Microsoft Partner

• Desktop Window Manager has stopped working after installing Defender Pro 2012 5 in 1

  Hello

  My father has a Windows Vista. It works very well. Until we installed Defender Pro 2012 5 in 1,

  It was a bit slow... the screen flickers of its lights for a few seconds every 10 minutes, I get this... I already have contact Defender Pro, and they said that it was not their fault.

  Help, please!

  DESKTOP WINDOW MANAGER HAS STOPPED WORKING
  Windows can check online for a solution to the problem

  -> online and are looking for a solution (recommended)
  -> close

  APPCRASH
  Application name: Dwm.exe
  Application version: 6.0.6002.18005
  Application timestamp: 49e02696
  Fault Module name: ntdll.dll
  Fault Module Version: 6.0.6002.18327
  Timestamp of Module error: 4cb74dd3
  Exception code: 80000003
  Exception offset: 0000000000045f00
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 1033
  Additional information 1: 0fef
  More information 2: 0d8b4b37a0c1e529a7398b6615cc3528
  Additional information 3: f196
  Additional information 4: acf765d48a0657c8822f379a6b5f3b91

  Read our privacy statement:
    http://go.Microsoft.com/fwlink/?LinkId=50163&clcid=0x0409

  Sorry to tell you,

  I already solved the problem.

  Just to let you know, I buy the product, because

  I used the free and they don't really work (IN MY OPINION).

  Anyone has this PROBLEM (appcrash)

  Go to start

  Click on Control Panel

  go to appearance and personalization

  Click on appearance color of windows.

  then click on settings in the appearance of progress.

  under the gaze of point for the theme of basic or something like that.

  Want more info on Dwm.exe?

  Click here-> http://www.howtogeek.com/howto/windows-vista/what-is-dwmexe-and-why-is-it-running/

• Windows Vista has stopped working properly

  
  

  I get a problem report that says that Windows Vista has stopped working properly. It is said to know if I have 32 or 64 bit system. For this I am told to click the Start button, click computer. When I click on start I get a computer. What should I do now?

  "pastafasul" wrote in message News: * e-mail address is removed from the privacy * .com...

  
  

  I get a problem report that says that Windows Vista has stopped working properly. It is said to know if I have 32 or 64 bit system. For this I am told to click the Start button, click computer. When I click on start I get a computer. What should I do now?

  If you see the icon on the desktop, do a right click on that and then left click on properties. The window that opens has all the information you need.
   
  If no icon, and then start Windows Explorer and right click on computer it followed by the left-click on it.

• After installing Ubuntu 11.04, Windows Vista has disappeared.

  Original title: Windows vista is missing

  After installing Ubuntu 11.04 (Natty Narwhal) my other OP system Windows vista has disappeared. I don't get a menu to choose which OP system I want to use. The grub menu 2 does not include an entry for windows. My computer directly boots into Ubuntu. I tried to put the installation disc in the status bar to try to recover the system but nothing works. Can someone help me please? Isetta cordially.

  Hi Isetta,

  It seems that after installing Ubuntu, grub 2 took control of Boot Manager and changed the boot sequence. To change the startup entries to get Vista, you must contact Ubuntu for assistance on changing the grub boot entries 2.

  You can see the following link to get in touch with Ubuntu.

  Ubuntu Forum

  Hope this information is useful.

• My installation disc for windows vista has an option "fix." This option allows to reset lost passwords?

  original title: repair windows

  My installation disc for windows vista has an option "fix." This option allows to reset lost passwords? If yes how?

  Hi Martine regina,.

  We will not be able to reset the password by using the option repair; you will need password reset disk.

  For more information on the same, you can check the link below:

  What to do if you forget your Windows password:http://windows.microsoft.com/en-US/windows-vista/What-to-do-if-you-forget-your-Windows-password

  Create a password reset disk:http://windows.microsoft.com/en-US/windows-vista/Create-a-password-reset-disk

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Desktop Window Manager has stopped working after loading of updates 12/10/10 MS

  Once the download and installation of updates for Windows 12/10/10 patches, Desktop Window Manager has stopped working.  Event viewer lists under Applications:

  Name: Application
  Source: Application error
  Date: 2010-10-13 09:59:47
  Event ID: 1000
  Task category: (100)
  Level: error
  Keywords: Classic
  User: n/a
  Computer: has
  Description:
  The failing application name: Dwm.exe, version: 6.1.7600.16385, time stamp: 0x4a5bc541
  The failed module name: nvwgf2umx.dll, version: 8.17.12.5922, time stamp: 0x4c5424d5
  Exception code: 0xc0000005
  Offset: 0x000000000007c160
  ID of the process failed: 0xb0c
  Start time of application vulnerabilities: 0x01cb6aefa117a51c
  The failing application path: C:\Windows\system32\Dwm.exe
  Path of the failing module: C:\Windows\system32\nvwgf2umx.dll
  Report ID: e6dfd048-d6e2-11df-9660-00271383b7fe

  The operating system is Win 7 x 64.  Video card is a Gigabyte GTS450OC1 with its latest driver running on an Intel DP55KG MB with 8 GB memory Corsair XMS3.  The system was fully functional and stable immediately before the update.  I don't know which of the 18 patches is in conflict with the nvwgf2umx.dll file.  Device Manager reports no hardware problem with any component.

  In my attempts to solve the problem, I run chkdsk f, sfc/scannow (which have reported no problem) and reloaded the video driver (without uninstall first).   Nothing works so far.  I even tried to defragment the master file with Diskeeper 2010 start time Table Defragger (based on another post, I've found), also without success.

  What is the reference for this?

  This may seem like the thing the more janky to post, but I got the same error several months:

  Problem event name: APPCRASH

  Application name: Dwm.exe

  Application version: 6.1.7600.16385

  Application timestamp: 4a5bc541

  Fault Module name: nvwgf2umx.dll

  Fault Module Version: 9.18.13.1422

  Timestamp of Module error: 51427a 68

  Exception code: c0000005

  Exception offset: 000000000013fe0b

  OS version: 6.1.7601.2.1.0.256.1

  Locale ID: 1033

  Additional information 1: bd9d

  More information 2: bd9dfb84ef7bbf0c089fd3d5f079469b

  Additional information 3: ec39

  Additional information 4: ec39233315f018bea3fd5d4de7e9458f
  And could not cancel the record/re-record the dll it error out on an entry point missing or whatever.
  So what for some reason any worked for me is to rename C:\Windows\System32\nvwgf2umx.dll to nvwgf2umx.dll.bak (all other copies of this file are in the folder DriverStore).
  After that, I ran from an administrator command prompt
  net stop uxsms
  net start uxsms
  
  
  And miraculously all started working again.  I'm running a GTX570 with latest drivers nvidia from Scripture.
  Note: You probably shouldn't be move/rename things in System32 unless you are confident and have your data backed up.  It worked for me, but who knows you.

• When I turn on my computer desktop-windows vista - I get the message that Multimedia Keyboard Driver has stopped working.

  How can I fix the error message that reader Multimedia Keyboard stopped working.  My keyboard is a

  0817-gateway model # KB.

  Hello

  I suggest you to follow these steps and check if that helps:

  Method 1:
  Start the computer in safe mode and check if the same problem occurs:
  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  Method 2:
  If it works fine in safe mode, and then try to perform the clean boot and check if it helps:
  http://support.Microsoft.com/kb/929135

  NOTE: When you are finished troubleshooting, make sure that you reset the computer in start mode normal such as suggested in step 7 of the above article.

  It will be useful.

• Windows Vista has stopped working

  I'm trying to fix my moms laptop that has windows vista on it. I can get it to start very well is not the problem. I can sign and take an account, if I open the Task Manager to get to the desktop. In the contrary case, it freezes on the Welcome screen. The laptop only works in safe mode, but clearly this is not what I want.

  I want to plant restoration of the thing. But he said that I did not restore on the computer points. I tried to go into the Protection system and I can only change the name of the computer. I'm trying to set up the restore point, but it just doesn't work. Can someone please tell me how to plant to restore this laptop until I drive me nuts?

  (The model is compaq presario CQ60 with processor intel pentium dual core, clear of Windows Vista)

  Hello

  System restore points are not a resumption of the plant back to new condition.

  Here's how to do it with a HP Compaq laptop.

  "Performing a recovery of the system HP (Windows Vista)"

  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c00814731&cc=us&destPage=document&LC=en&tmp_docname=c00814731

  Turn on the computer and immediately press the F11 key several times , about once a second, until the Recovery Manager opens.
   
  Or in Vista, use the HP Recovery Manager to reinstall the operating system.
   
  All the information are in the link.
   
  See you soon.

• Windows Vista has crashed, "the operating system not found" error, can I load Windows XP on a partition?

  I have an Acer Aspire 5516, with pre-installed Windows Vista. I didn't know that it did not come with a recovery disk UNTIL my system crashed! During a routine virus scan, I got a blue screen saying a major problem has been found and the system has been shut down. I followed the instructions to gracefully shut down my laptop. When I turned this back on after the "Acer" logo he went to a black screen with info on my computer and the last line States "not found operating system". That's when I discovered there was no recovery disc & it is integrated into the system. To access this system you we F8 to enter safe mode, then Alt F10 to access 'erecovery management system. Neither one of these functions operate! Still getting the black screen with "operating system" not found I have a Windows XP my laptop previous. What I was wondering is if I can load on my Acer, possibly on a partition, in order to be able to get into my laptop and save all of my files? I'm terrified of losing everything I have! I have thousands of pictures that I can't replace. If anyone can help please do! I am on a very limited income & can not really afford professional help. Thank you very much in advance!

  Hello

  normally with an Acer you press Alt + F10 at startup to start the hidden recovery partition recovery, not F8, then this combo

  but you do not have an option to save your data, that

  in daily use acers normally have a system partition, a partition of data to save your data, etc. to and also this hidden partition recovery

  and read this on data recovery, too;

  Data recovery

  1. remove the hard drive and it slave in another computer

  2 buy or borrow a USB disk drive hard put in yout case then plug it into another computer and read the hard drive like this

  3. try Knoppix

  http://www.Knopper.NET/Knoppix/index-en.html

  BUT this method 3 depends on your hardware in the computer that failed

  read this information about method 3:

  http://www.Knopper.NET/Knoppix/index-en.html

  Download/save the file Knoppix Live CD ISO above.

  http://isorecorder.alexfeinman.com/isorecorder.htm

  Download the Vista software from the link above.

  After installing above ISO burning software, right click on the Knoppix ISO file > copy the Image to a CD.

  Knoppix is not installed on your PC; use only the resources of your PC, RAM, graphics etc.

  Change the boot order in YOUR computer/laptop to the CD/DVD Drive 1 in the boot order.

  Plug a Flash Drive/Memory Stick, BOOT with the Live CD, and you should be able to read the hard drive.

  When the desktop loads, you will see at least two drive hard icons on the desktop (one for your hard drive) and one for the USB key.

  Click on the icons of hard drive to open and to understand which drive is which.

  Click the icon for the USB drive and click on "Actions > Change the read/write mode" so you can write to disk (it is read-only by default for security reasons).

  Now to find the files you want to back up, just drag and drop them on the USB. When you're done, shut down the system and remove the USB key.

• Advised by a Lenovo Support Technician that Lenovo IdeaPad u330 that equipped of Windows Vista has been infected

  My pc is a Lenovo IdeaPad u330 that running Windows Vista Home Premium 32-bit.  I have 3 PC over a wireless home network.  Recently, I have been instructed by the Lenovo Support telephone call center to enter "cmd" in the Task Manager, did so and was taken to the black C:\WINDOWS\system32\cmd.exe screen.  I had to then enter "cmk", did and received message next-'cmk' is not recognized as internal or external command, an executable program or batch file.  Support staff advised that this indicated my pc has been seriously infected and needed immediate attention.  My pc works well and I have McAfee installed, having received no warning and a complete analysis of all recommended system was OK.  Should I worry or the person was just trying to sell a service?  Thank you.

  * original title - cmd & KMC - suggested by Lenovo Support *.

  Hello

  There are no KMC program or command on most computers. So, if we had to
  to be a CMK on Lenovo computer (or you) should have Add.

  Did you call Lenovo support, or maybe it was one of those false calls trying to get
  money or your personal information? Hard to believe that Lenovo would use these tactics
  trying to sell a program or service.

  Check with Lenovo support and forums.

  Support from Lenovo and downloads
  http://www-307.IBM.com/PC/support/site.WSS/homeLenovo.do

  Lenovo forums
  http://forums.Lenovo.com/

  =========================================================

  If you need search malware here's my recommendations - they will allow you to
  scrutiny and the withdrawal without ending up with a load of spyware programs running
  resident who can cause as many questions as the malware and may be more difficult to detect as the
  cause.

  No one program cannot be used to detect and remove any malware. Added that often easy
  to detect malicious software often comes with a much harder to detect and remove the payload. Then
  its best to be thorough than paying the high price later now too. Check with them to one
  extreme overkill point and then run the cleaning only when you are sure that the system is clean.

  It can be made repeatedly in Mode safe - F8 tap that you start, however, you must also run
  the regular windows when you can.

  Download malwarebytes and scan with it, run MRT and add Prevx to be sure that he is gone.
  (If Rootkits run UnHackMe)

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Malwarebytes - free
  http://www.Malwarebytes.org/

  Run the malware removal tool from Microsoft

  Start - type in the search box-> find MRT top - right on - click RUN AS ADMIN.

  You should get this tool and its updates via Windows updates - if necessary, you can
  Download it here.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN
  (Then run MRT as shown above.)

  Microsoft Malicious - 32-bit removal tool
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=AD724AE0-E72D-4F54-9AB3-75B8EB148356&displaylang=en

  Microsoft Malicious removal tool - 64 bit
  http://www.Microsoft.com/downloads/details.aspx?FamilyId=585D2BDE-367F-495e-94E7-6349F4EFFC74&displaylang=en

  also install Prevx to be sure that it is all gone.

  Download - SAVE - go to where you put it-right on - click RUN AS ADMIN

  Prevx - Home - free - small, fast, exceptional CLOUD protection, working with others
  security programs. It is a single scanner, VERY EFFICIENT, if it finds something to come back
  here or use Google to see how to remove.
  http://www.prevx.com/   <-->
  http://info.prevx.com/downloadcsi.asp  <-->

  Choice of PCmag editor - Prevx-
  http://www.PCMag.com/Article2/0, 2817,2346862,00.asp

  Try the demo version of Hitman Pro:

  Hitman Pro is a second scanner reviews, designed to save your computer from malicious software
  (viruses, Trojans, rootkits, etc.). who infected your computer despite safe
  what you have done (such as antivirus, firewall, etc.).
  http://www.SurfRight.nl/en/hitmanpro

  --------------------------------------------------------

  If necessary here are some free online scanners to help the

  http://www.eset.com/onlinescan/

  New Vista and Windows 7 version
  http://OneCare.live.com/site/en-us/Center/whatsnew.htm

  Original version
  http://OneCare.live.com/site/en-us/default.htm

  http://www.Kaspersky.com/virusscanner

  Other tests free online
  http://www.Google.com/search?hl=en&source=HP&q=antivirus+free+online+scan&AQ=f&OQ=&AQI=G1

  --------------------------------------------------------

  Also follow these steps for the General corruption of cleaning and repair/replace damaged/missing
  system files.

  Run DiskCleanup - start - all programs - Accessories - System Tools - Disk Cleanup

  Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
  RUN AS ADMIN

  Enter this at the command prompt - sfc/scannow

  How to analyze the log file entries that the Microsoft Windows Resource Checker
  (SFC.exe) program generates in Windows Vista cbs.log
  http://support.Microsoft.com/kb/928228

  Run checkdisk - schedule it to run at the next startup, then apply OK then restart your way.

  How to run the check disk at startup in Vista
  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  -----------------------------------------------------------------------

  If we find Rootkits use this thread and other suggestions. (Run UnHackMe)

  http://social.answers.Microsoft.com/forums/en-us/InternetExplorer/thread/a8f665f0-C793-441A-a5b9-54b7e1e7a5a4/

  I hope this helps.

  Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

• the Start button and the taskbar disappeared in windows vista

  Original title: start button

  the Start button and the taskbar disappeared in wondows vista.

  It's ok in the profiles of other users.

  Hi GavinAlston,

  ·         Since when are you facing this problem?

  ·         You did it last changes before the show?

  ·         Are you able to see the desktop icons?

  Step 1: I suggest that you put your computer in safe mode and check if it helps.

  What is safe mode?

  http://Windows.Microsoft.com/en-us/Windows-Vista/what-is-safe-mode

  Start your computer in safe mode

  http://Windows.Microsoft.com/en-us/Windows-Vista/start-your-computer-in-safe-mode

  If you are able to run safe mode then try to clean boot.

  Step 2: I recommend you perform the clean boot.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: After troubleshooting, be sure to set the computer to start as usual as mentioned in step 7 in the above article.

• Remote Desktop - Windows Vista-based computer to a Windows 7 computer on a local network in my office

  I have a laptop Windows Vista Home Premium that is trying to connect to my Windows 7 desktop. It worked fine when my desktop computer was Windows XP and I was running the same laptop Vista Windows 7, I am now.

  What has changed? I have a modem/router to two sons and has not changed the settings. I just tried opening port 3389 and cutting the firewall of Windows with the same results.

  I have a VPN and the game works fine.

  Get remote desktop dialog box for opening and saving in and I know that it is configured correctly, because when I take my Vista laptop to the office the RD connection works fine and I can see and I work on my Windows 7 desktop computer, so the problem is either something on my home network or with my ISP - using DSL - ideas?

  Thank you

  Joe

  Ideas:

  • You have problems with programs
  • Error messages
  • Recent changes to your computer
  • What you have already tried to solve the problem

  Hi audacity.

  Terminal Services Gateway (TS Gateway) server enables authorized users to connect to a computer on a corporate network wherever you are on the Internet. Ask your network administrator to provide permission to access them through the TS Gateway.

  Remote Desktop connection: frequently asked questionshttp://windows.microsoft.com/en-us/windows-vista/Remote-Desktop-Connection-frequently-asked-questions

  The problems of desktop remotely
  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-Remote-Desktop-problems

  Bindu R - Microsoft Support
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Satellite A100 - 049 (PSAAR) - registration of Windows Vista has stopped working

  My Toshiba Satellite A100-049 (PSAAR) came loaded with Windows Vista Home Premium.
  On each occasion my computer boot the, "record of Vista has stopped working" message.
  Here are the details of the error message below.
  Anyone have a similar problem or have a solution to this problem?

  Problem event name: CLR20R3
  Problem Sig 01: Toshibaregistration.exe
  Problem Sig02: 023.0.2538.28272
  Problem Sig03: 45801f61
  Problem Sig04: System.Managment
  Problem Sig05: 2.0.0.0
  Problem Sig06: 4536f344
  Problem Sig07: 111
  Problem Sig08: 123
  Sig09 problem: access to the authorization system
  OS Version:6.0.6000.2.0.0.768.3
  Local ID: 6153

  This happens especially if someone install a clean Version of Vista.

  Please call Microsoft. You must activate Vista by phone.
  As far as I know the phone call is free. After that it all works again.