Need advice on the low storage space

Similar Questions

• Need help with the data storage store, local array and network connections

  Need help with my ESXi 4.1 installation

  My hardware:

  I built a server with an Asus P6T whitebox, i7 920, 12 Gig RAM, NIC, Intel Pro1000 PT Quad, 3ware 9650SE-12ML with 8 1.5 TB SATA green in a raid 6 array gives me about 8 + TB with a spare drive all housed within a NORCO RPC-4220 4U Rackmount Server chassis.  I also have a 500 GB SATA drive which will hold the ESXi and virtual machines.

  The network includes a firewall, Netgear Prosafe FVS336G, GS724Tv of Netgear ProSafe 24 port Gigabit Managed Switch on a dhcp cable modem internet service provider.

  I also have 2 old NetGear SC101T NAS disks (4to) I want to connect to the system how some - at a later date have... data on them and want to transfer to the new storage array. I always looking into the question of whether they will work with ESXi 4.1, or I might have to only access it through Windows XP.

  My Situation:

  I have already installed ESXi 4.1 and vsphere client with no problems and it is connected to a dhcp cable internet service.  I've set up host via a dynamic DNS service name give me a static hostname on the internet.  I installed three machines to virtual OS successfully at the moment and now want to first start by creating a multimedia storage server which will use some of this new 8 TB array, then separate data storage for use with a web server small overhead storage and a backup.  It is a domestic installation.

  Help with the data store and network:

  I was doing some reading, because I'm new to this, and it looks like I'll probably want to set up my table via ESXi as a nfs disk format.  Now, the data store is usually in another physical box from what I understand, but I put my readers and ESXi all in the same box.  I'm not sure that the best way to put in place with grouped network cards, but I want to make this work.

  I understand that in ESXi 4.1 using iSCSi LUN must be less than 2 TB, but nfs - I should be able to add a bigger partition then 2 TB (for my multimedia) in nfs, right? or should I still add it separately as a separate 2 TB drives and then extend them to get the biggest space.

  Any suggestions or direct resources showing examples on how to actually add some parts of the table as data warehouses separate nfs.  I know that to go to the configuration tab, and then select Add to storage, and then select nfs. I have not my picture, but it's here that I don't know what to do because ESXi 4.1 system already has an address, should I put the same thing to the new data store array also (will it work?), and what should I use for the name of the folder and the store of data... just do something to the top.  I thought to later install Openfiler (for a multimedia storage using this table server) as a virtual machine, use the table with esxi so that I can access the same storage space with widows and linux-based systems.

  I also know I have to find a way to better use my quad nic card... put in place of virtual switches, grouping, etc HELP?

  Any direction, assistance, similar facilities to sample, suggestions or resources that would help would be great. I did a lot of hunting, but still a little confused on how to best to put in place.

  You must think of VMDK files of large databases with records of random size guest go read some data (a DLL or an INI file), maybe write some data back, then go read other data. Some files are tiny, but certain DLLs are several megabytes. It's random i/o all and heavy on the search time. IO Opsys is small random operations that are often sequential (go read data, write data, go read other data,...) so that deadlines are critical to the overall performance. That's why people say OPS are / s of reference and forget the MBs flow. The only time where you bulk transfers are when you read media (ISO files).

  Well, now forget all this. Actually the disk activity will depend on the specific applications (database? mail server? machines compiler?), but the above is true for boots, and whenever applications are idle. You should see the profile to know.

  RAID 10 is faster (and often more reliable) than RAID 5 or RAID-6 except in certain specific cases. In General RAID 10 is ideal for many random writes, since the calculation of parity for RAID-5 and - 6 adds to the overall latency between command and response - latency is cumulative if a little slow here and a little slow it adds up to a lot of overall slow synchronous especially with e/s on a network. OTOH RAID-5 and -6 can produce faster readings due to the number of heads, so you can use it for virtual machines that transfer bulk. Test. You may find that you need several different types subdashboards for best results.

  You said 3ware, they have some good grades on their site, but don't believe it. With my 9650 that I found myself with only a couple of their recommendations-, I put the (simple) table for allocation size 256 k, nr_requests at 2 x the queue_depth and use the planner date limit. I had the habit for the Ext4 file system formatted with stride and stripe-width synced to the table and used the options large_files with fewer inodes (do not use the huge_files option unless you plan to have single VMDK files in the terabyte range). Use a cache of great reading in advance.

  Virtual machines use VMDK files in all cases except raw iSCSI LUN that they treat native disks. VMDK is easier to manage - you can make a backup by copying the file, you can move it to a PC and load it into another flavour of VMware, etc. There could be some features iSCSI to your San as a transparent migration but nothing for me. NFS has less chatter of Protocol if latency lower times to complete an operation. NFS is good to read and write a block of data, that's all it boils down to.

  UPS is good, but it won't help if something inside the machine explodes (UPS does nothing if the PC power supply goes down). If the RAID card has an option for a battery backup module, so it can contain some writings in memory and may end up the disk i/o after replacing the power supply. 3ware also limits the types of caching available if help is not installed, and you get just the right numbers with the module.

• Guard application launch at the start of the appliance, also need advice for the implementation of network methods

  Hi all

  I'm new to the development of Blackberry and I'm writing a relatively simple application to run on 7.1.

  So far the development was interesting, I managed to create my user interface using resources online (mainly this forum), but today I tried to implement some of the network classes that I need and now I just met constant problems.

  I use Eclipse SDK 3.7.2 (the one that comes with the plugin RIM)

  First question:

  I'm not sure what I changed, but today I noticed that whenever I start the Simulator (by sim 9360) my application is started during the initial startup process. I don't think he did this before, but to be honest, I wasn't paying much attention. I think it starts at the start of the device is because I put a breakpoint in the constructor for my class from the main screen, which is hit before the Simulator happens even to the point where it is ready for user interaction. In addition, once it is ready, if I press the BB button, I see my registered application.

  I don't have it set to automatic start in .xml descriptior enforcement.

  I started this application on the HelloBlackBerry sample, here is my main method for the entry of the application:

  public static void main( String[] args ) {
          appSettings = AppSettings.fetch();
          // Create a new instance of the application and make the currently
          // running thread the application's event dispatch thread.
          HelloBlackBerry theApp = new HelloBlackBerry();
          theApp.enterEventDispatcher();
          //openConnection();
  
      }
  
  
  

  As far as I know, this is the only entry point for the application.

  More code

      public HelloBlackBerry() {
          // Push a screen onto the UI stack for rendering.
          mainScreen = new ScreenHelloBlackBerry();
          pushScreen( mainScreen );
      }
  

  Here is the method of. my class AppSettings fetch()

      // Retrieves a copy of the effective properties set from storage.
      public static AppSettings fetch()
      {
          AppSettings savedSettings = (AppSettings) _store.getContents();
          return new AppSettings(savedSettings);
      }
  

  Some of this code that I wrote myself, the persistence store cause the launch of my car?

  I tried to reset the Simulator to the factory settings, no change.

  All applications initialized during the startup of the device and then closed shortly after?

  Part 2: Need advice for the implementation of functions of network in the application

  I need to implement some methods that will retrieve data from a web service, and I also need to send data to this service. What I've read, the ConnectionFactory is the way to go. I want my application to make a request when the application is open and can check on a set interval. I didn't know exactly how to go about adding another thread for networking, I understand that network connections should not be created on the thread main event, so I tried to do this:

  The constructor of my class that implements screen (ScreenHelloBlackBerry), I use the following to create a modal dialog box to prompt the user for a username, I also try networking wire in the same segment of spawning:

          public ScreenHelloBlackBerry(){...initialize fields and managers, add it all together...then near the end
  
  //This will open the confirm dialog when the application is launched
          UiApplication.getUiApplication().invokeLater(new Runnable() {
                public void run() {
                    openConfirmDialog();
                  //start connection - Possibly broken
                    ConnectionThread ct = new ConnectionThread();
                    ct.start();
                }
          });
  

  I don't know if it's somehow OK to do, but it seems to work for what I need. I want a user who launches the application at the prompt, and if a user switch applications, when they come back they wondered again (unless they close the app and reopen it).

  Here is my ConnectionThread:

  public class ConnectionThread extends Thread
  {
  
      public void run()
      {
  
            ConnectionFactory connFact = new ConnectionFactory();
            ConnectionDescriptor connDesc;
            connDesc = connFact.getConnection("http://www.google.com");
            if (connDesc != null)
            {
                HttpConnection httpConn;
                httpConn = (HttpConnection)connDesc.getConnection();
                try
                {
                    final int iResponseCode = httpConn.getResponseCode();
                    UiApplication.getUiApplication().invokeLater(new Runnable()
                    {
                        public void run()
                        {
                            Dialog.alert("Response code: " +
                                          Integer.toString(iResponseCode));
  
                        }
                     });
                    httpConn.close();
  
                 }
                 catch (IOException e)
                 {
                   System.err.println("Caught IOException: "
                        + e.getMessage());
                 }
            }
      }
  }
  

  At the moment it has basically unmodified code from a sample that I found, I'll be retooling to meet my needs whenever I can make it work. I HAD this work to the point where, after the closed user confirm this dialog, a few moments later a an alert dialog appears with the 302 response code. I don't know what changed, but now it doesn't work at all, and if I try to scroll with the debugger, I can't past the httpCon.getResponseCode (). I've seen some mistakes earlier on "no record of service was set up", and I also had once a timeout exception.

  I'm sure I'm doing this wrong, but at the same time as I said WAS working, and now it is not. If someone has done this far, thank you very much for your time and advice are much appreciated.

  Also, should I try to start the thread of the network of the UIApplication class instead of the screen? There is currently very little happening in the class that extends UIApplication, do I spend most of my business logic out of the class of the screen and in the UIApplication class?

  Thanks in advance!

  Hi all

  Just to conclude this topic for those who are interested, I found an excellent guide to the implementation of networks in applications of BB, click here for a link.

  About my application being started at the start of the simulator of the device, I found that on a device real this behavior is not complied with, and in addition, the behaviour seems to have stopped after uninstallation and reinstallation of my Simulator.

  See you soon,.

• Why have I not more volume of applications than the total storage space?

  Why did I 124,24 GB of applications if the total storage space is 121 GB? That's happened?

  

  Please rebuild the Spotlight index. If you try to search now, there will be an indication that the indexing is in progress.

• How to downgrade my iCloud upgrade? I need is no longer the additional storage space. I tried on my devices, but it still says that my current plan is 50 GB at $0.99

  I have tried to downgrade my storage in iCloud on my devices, but always says that I pay for $0.99 50 GB upgrade

  Is no longer need her so, how can I stop these payments?

  You can decrease the amount of storage by selecting a new plan directly from your iPhone, iPad, iPod, Mac or PC (for example, a plan of 5 GB to replace a 200 GB plan). The downgrade will take effect after the end of your monthly or annual subscription in progress.

  iOS

  1. If you use the iOS 8 or laters, go to settings > iCloud > storage. If you are using an older version of iOS, go to settings > iCloud > storage and backup.
  2. Click Change storage Plan.
  3. Press Downgrade Options and enter your Apple ID.
  4. Choose a different plan to use when the expiration of your current storage plan.
  5. Tap done.

  OS X

  1. Choose the Apple menu > System Preferences, and then click iCloud.
  2. Click on manage in the lower corner on the right.
  3. In the upper right corner, click Change storage Plan.
  4. Click Options to Downgrade.
  5. Enter your Apple ID password, then click on manage.
  6. Choose a different plan to use when the expiration of your current storage plan.
  7. Click done.

• How to create the same storage space in the database of test as in production

  I used the following commands:
  (as of 10 gr 2)
  expdp DIRECTORY = DATA_PUMP_DIR SCHEMAS = EXCLUDE MDLOG = DUMPFILE = mdlogMETADATA.dmp STATISTICS include happy tablespace = metadata_only =
  
  Then:
  (in 11 GR 2)
  Impdp DIRECTORY = DATA_PUMP_DIR DUMPFILE = mdlogMETADATA.dmp include TABLESPACE sqlfile = c.sql =
  
  According to the following positions, it should work
  How to find the user name and a name indatapump import tablespace
  
  [http://www.rampant-books.com/art_nanda_datapump.htm | http://www.rampant-books.com/art_nanda_datapump.htm]
  
  instead I get
  ORA-39002: invalid operation
  ORA-39168: TABLESPACE object path was not found.
  
  Now I'm looking for the incompatible options between (10 gr 2) expdp and impdp (11 GR 2)... and if include = TABLESPACE should be replaced by choice...
  
  During this time... is there something that can tell me if I make mistakes?
  
  Tanks

  Hello

  The expdp command you listed in your first post may not work. You have exclude and include in the same order.

  Exclude said excluding these items but includes everything.

  Include says include only these objects and exclude everything else.

  If you use the command expdp of your second post, there is no tablespace objects in a schema export. Include = tablespace will only recreate the tablespaces and not objects in storage. If you want to do this, you must delete the schema = MDLOG and add the full = Y. Tablespace definitions are included in a full export.

  What is your ultimate goal? You want just the definitions of tablespace moved? If so

  complete expdp = include = tablespace directory =...

  If you want all the storage space and the objects in these storage spaces, so I think it would be 2 steps:

  complete expdp = include = tablespace directory...
  expdp tablespaces = tbs1, tbs2,... happy = metadata_only...

  You have not need of content = data_only, but you had it on two orders expdp so I guess that's what you wanted, so I added it.

  If you have a different purpose, then publish it and I'll see what I can find.

  Dean

  p.s. If you want to see what items are included in a particular mode you can query sys.datapump_paths. Het_type is the mode

  Full = look het_type DATABASE_EXPORT
  schemas =... Watch het_type SCHEMA_EXPORT
  tables =... Watch het_type TABLE_EXPORT
  tablespaces =... Watch het_type TABLE_EXPORT
  look at transport: het_type TRANSPORTABLE_EXPORT

  Published by: Dean WINS on February 2, 2010 09:18

• Low storage space

  I have the x 2 H210DX spectrum. My HDD shows that I have C: 38 free 103 GB GB, D: 1.51 GB 14.6 GB free. It is less than 3 weeks old. I don't have movies or music here. The greatest programs I have are Windows Office 2013 and McAfee, but it shouldn't take nearly everything a lot of place. 90% of my documents/files are stored online. About how much free space is sent with this product? And what is to take all this space? I think it is my computer freezes often... usually when you use a program on the internet.

  Hi wap_8. I am not sure how much space is available out of the box. The D: partition looks properly said, as is the HP Recovery partition, allowing you to easily reset your computer to the default settings. The c: drive is not that far. Windows 8 could be an installation of 30-40gig, more updates, and factory loaded software.
  
  While the title of this document is not exactly specific to your concern, the steps will do basic cleaning and show you were to investigate your installed programs: Solve Low Disk Space errors (Windows 8)
  
  Here are some additional troubleshooting, specific to your computer to freeze when using the Internet:

  Windows 8 stops responding or becomes very slow after you connect to the Internet
  Computer hangs or crashes in Windows 8

  Let me know how it turns out.

• Saturation of the profile storage space.

  Having recently restored from a backup, I get a dialog box that I have exceeded my maximum profile storage space and must move data to storage in order to connect my computer. How can I safely do this, and why all of a sudden is happening? It's the same profile as I did for 3 years!

  This error occurs usually after a computer has been infected then first make sure the computer is completely virus/malware-free. Then locate the disk quotas that can be defined. If the machine is clean and there is no set of disk quotas, copy the lines between asterisks a Notepad document and save it as undopolicy.reg. Double-click undopolicy.reg to merge into registry.

  *****
  Windows Registry Editor Version 5.00

  [HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Policies\System]
  'EnableProfileQuota ' = -.
  'ProfileQuotaMessage ' = -.
  "MaxProfileSize" = -.
  'IncludeRegInProQuota ' = -.
  'WarnUser ' = -.
  'WarnUserTimeout ' = -.
  MS - MVP - Elephant Boy computers - don't panic!

• Best network design... Need advice on the best use of NIC

  I'm new to the concept of Distributed Switch so I need advice.

  Our current environment is the result of a vCenter 4.1 and ESXi 4.1 Enterprise Plus, but we are just using the standard vSwitch (1 for vMotion/Console and 1 for virtual machines).  When the distributed switch came out, we were warned that a vDSwitch could cause us problems if the server vCenter or database is down.  We could not connect directly to the host and make network changes because the vDSwitch is set in the database.  That's why we stayed with the Standard vSwitch only.

  Our farm is quite small, only 5 hosts but we run around 100 mV in this regard.

  We use currently servers HP DL385 G7, which have 4 cards integrated network, and we have a map of installed NETWORK 4 port card.

  I use the NETWORK 4 EtherChannel ports and trunk card to our virtual machines.

  I am currently using only 1 network card integrated for vMotion and 1 for the Service Console and they all have two of the other defined as secondary.

  This configuration has worked very well for us, but I realize that the latest version of ESXi has some new features that we could use.

  NEW CONFIGURATION

  I'll put up a new vCenter 5 and ESXi 5 environment and I am considering using the switch distributed instead of the usual vSwitch we use.  I'm also eager to take advantage of the multiple NIC vMotion.  All our cards are 10/100/1000 MB capable... No. 10 GigE.

  I think... use that map 4 NETWORK ports for my EtherChannel/trunk for just as our virtual machine before, but this would be set to vDSwitch1

  The mixture of my 4 other integrated ports, it's causing me grief.  Should they be on a standard vSwitch or vDSwitch?  Use 2 ports for vMotion and 2 for the Console?  I really thought to use 3 ports for vMotion and 1 Console port.  I could put the Console port to use one of the vMotion ports such as adapter of standby is... I'm so confused freaking!

  Any recommendations on how I should put up?

  Hello

  Given that you can't split your vmnic for each vSwitch I would recommend either keep configuration simular with the knoweldge if a whole nic fails, you will take a failure or as autumn has already been mentioned on 'Origin Port ID'. Lets do this out and give a little better example

  Current configuration

  vSwitch0

  VMNIC0 - NETWORK interface integrated - Service Console

  VMNIC1-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC2-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC3 - NETWORK interface integrated - VMotion (eve of Console of Service) (different IP or VLAN?)

  vSwitch1

  VMNIC4 - extension PCI NIC - Etherchannel trunk - PortGroup - VMNET

  Extension VMNIC5 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Extension VMNIC6 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Extension VMNIC7 - PCI NIC Etherchannel trunk-PortGroup - VMNET

  Now, to captured to eliminate any single point of failure that you could do is break your Etherchannel trunk and back this vSwitch from Port ID and Setup VMNIC2, VMNIC3, VMNIC4, VMNIC5 as vSwitch1 for your VMNET. Then the cable to multiple switches eliminate any single point of faiulre. If your standard configuration would look like this

  vSwitch0

  VMNIC0 - on - Board Service Console

  VMNIC1 - Board - Vmotion

  VMNIC6 - extension PCI NIC - Vmotion

  VMNIC7 - extension PCI NIC - Vmotion (standby Service Console)

  vSwitch1

  VMNIC2 - VMNET

  VMNIC3 - VMNET

  VMNIC4 - VMNET

  VMNIC5 - VMNET

  So to finish any request for psyhical nics on this particular configuration the Port ID of origin essentially around robins. If during your first VM is online it will be use VMNIC2 and nic forever, until a failure, in which case he will grab the next nic online. When your second VM is online it will use VMNIC3 forever, until a failure and so on. This still will give you around the same way through to as far as networking is concerned. However if you are attached to the trunk, etherchannel 4 GB and can obsorb a failure in case of failure, the network card 4 ports can stay.

  Distributed switching Setup

  Allows you to see how you can switch to distributed switching

  Let's start first of all, you can have EVERYTHING in switches distributed even the service console port if you wish. The resason why some people do not like to do this with the service console port is because IF your database is broken you cannot make any changes to the distributed switch. However it will not prevent a feature to your distributed it switches simply means, you can change them. Also if just getting worse and your DB has been declining for some time and you REALLY need to make a change to the service console port you can go into the console and change back to a standard vSwitch if need be. This allows the said look at some standard configs, you can work

  vSwitch0 (Standard)

  VMNIC0 - Service Console Port (Port Original ID or standby)

  VMNIC4 - Service Console Port (Port Original ID or standby)

  vSwitch1 (Standard)

  VMNIC1 - Vmotion

  VMNIC5 - Vmotion

  Distributed switch

  VMNIC2 - VMNET

  VMNIC3 - VMNET

  VMNIC6 - VMNET

  VMNIC7 - VMNET

  Now this config using originating port ID and breaks your etherchannel if you want to keep your configuration with the etherchannel it can look like this

  vSwitch0

  VMNIC0 - NETWORK interface integrated - Service Console

  VMNIC1-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC2-Onboard NIC - VMotion (different IP or VLAN?)

  VMNIC3 - NETWORK interface integrated - VMotion (eve of Console of Service) (different IP or VLAN?)

  Distributed switch

  VMNIC4 - VMNET

  VMNIC5 - VMNET

  VMNIC6 - VMNET

  VMNIC7 - VMNET

  Other changes to the configuration may also put the vmotion in distributed witch the VMNET but you would to VLAN, or you could create a second Distributed switch and put it as long as there are 2 network cards. It can go either way. The main advantage of a distributed switch is that it brings all of your settings with you in any host. So trade ect all your VIRTUAL networks is really easy to reproduce if a new host is brought online, all you have to do is to add the new host network cards in the distributed switch and your config is done. With that in mind lets look at the service console. This console is always configured on EACH Setup program that out you of the box if not that you really need to have these parameters transported on several hosts that is another reason why most people just don't. VMotion is up to you, I have seen and configured two ways, it all depends on how simple you want to keep it or think of switching / vlaning / port of groups.

  If you have any questions please let me know, I hope this has helped

• I need advice on the most suitable package to buy

  I need advice on which is the best package to buy

  Hi Lorna,

  If you want to edit and create a PDF file you need Adobe Acrobat.

  Adobe Reader is to view the PDF files on your computer.

  Thank you

  Kapil Malik

• Need advice on the recovery CD and Vista upgrade on Satellite M100-222

  I want to share my problem to get some tips. I got a laptop Satellite M100-222 Windows XP and Vista capable, then I got an upgrade to Vista and it works with few problems that do not recognize some programs.

  That's why I have some needs and need your help and support and they are as follows:
  1 - is possible to reformat using the upgrade of Vista, or need to reformat with XP first and then update with Vista.
  2 - I tried several times to start the CD, DVD (product recovery) to reformat the laptop. However it is said (operating system not found).

  Kindly enlighten me.
  Concerning

  With regard to the point;

  (* 1) * If you ONLY upgrade Vista CD, then it s necessary to start the first restore XP CD, and then upgrade to Vista.

  (* 2) * usually start from the CD/DVD recovery must format the HARD drive and need to install the new image of Toshiba. Please check if you have started since the right recovery CD! Don't mix it with the Express Media Player recovery CD!

• Need advice with the hard drive upgrade

  Greetings Applelonians:

  I bought a new HD 480 GB SSD for my 15 MBP (to 2011) to try to help improve the performance and install it myself. I'm hoping to get some tips on the sequences necessary for install and then restore my files Office 2011. (I've known slowness notable speed as well as issues of program Outlook-so think I should try to start more as fresh as possible).

  I'm clear on the mechanical steps to install the drive, but there seems to be a few options on the side of software I found. I have a copy of Snow Leopard, which came with my MBP, so in theory I think I should be able to install an operating system from scratch, and then do the upgrades, right?

  I also have a SATA cable / USB, I see that some have used to clone the existing HD. As mentioned above, I think I should start with a new installation of the operating system (which simply Mac store recommended for $80 there), so I don't think that cloning is the best option.

  Here are my questions:

  (1) if I install the new HD, because it is out of the box, and then insert my Snow Leopard, which will load the necessary drivers required? or do I need to format the drive (on the outside?) before you install it?

  (2) I have a Time Machine recent backup contains all my critical data that I need to restore (for most all files MS Office 2011). I was intending to do a new installation of Office 2011 after the installation of the HD and then restore my Office files from the external backup of TM. I wonder if the TM backup contains only files, or if it also contains the actual programs (e.g. office). If the latter, is there another method I use to transfer other files that a full restore?

  (3) also in this sense, once I get El Capitan, installed on the new disk, my TM of Yosemite Backup is in conflict with that?

  Thanks in advance for any comments and help!

  The f

  I recommend to format the new external SSD for Mac OS extended (journaled) and either use Time Machine or Carbon Copy Cloner to load the data on the new SSD.  Installation of Snow Leopard is not necessary.

  Ciao.

• Need advice replaces the screen HP Mini 2102

  Hey all,.

  I'm fixing a netbook HP Mini 2102 which was abandoned on the ground. The netbook works fine, except that now the screen is a little blurry and washed on the right side. Generally, when a computer screen is upward, trying to replace the converter display card, as was the case with a machine to HP Pavilion dv9000 I fixed recently.

  However, after dismatling the computer, I found no such ups on the screen, and after consultation with an HP support assistant very useful during a session of live chat who informed me that it is not a separate inverter Board available for purchase, I have come to believe that I need to replace the entire screen.

  If I'm not mistaken, the LCD part number is 589649-001 for this particular model that I am repairing. I created this post to confirm that the ups on this Mini Board can be replaced, and I need to replace the entire LCD screen - less camera, bezel and hinge, which all work fine - in order to solve the display problem.

  If you have any other suggestions as to what part I need, or if I have to take a completely different approach to the repair, please let me know before ordering the part of LCD screen.

  "Violence is the last refuge of the incompetent." -Issac Asimov, from its roman Foundation.

  Hello

  You are right, you can save money simply select the good parts. I think not much.

  Good luck.

• I can co on the "low disk space" on RECOVERY (d :)) disc warning?)

  Using the disk management program I dropped my C drive and I now have a new, unnamed, empty, no file system (I think), 55 GB drive, volume, disk, partition in more C drive, (which has still approx. 220 GB of free,) the complete RECOVERY D drive/disk/partition/volume 10 GB and a connected by USB-free 430 of GB external hard drive.

  Hello

  You have lost your time shrinks for difficulty D: C:

  Read this:

  Your recovery Partition was photographed on your hard drive during the production of your computer by the manufacturer for all of these reasons.

  1. to reinstall Vista from in the case of a failure of the system, based on individuals or the keys at startup.

  F10 or Alt + F10 or F11 are a couple of different manufacturers use sequences.

  You will need to ask your manufacturer for proper sequence.

  2. to make the recovery disks on if your drive hard breaks down, so that you can then reinstall the operating system on a new hard drive.

  Also ask them how to make records.

  Your D: Recovery Drive is should not be used for backups, defragmented, etc..

  There are backups on an external hard drive.

  To resolve the problems that have arisen with the recovery D: Partition, you will need to contact the manufacturer of your computer to remove all that has been added to it.

  See you soon.

• Need advice for the graphic shape on the image display

  I would like to help plot a circle above an image that is displayed in the get in JLabel, the purpose is, when you click on the image, the image with a small circle apperas instead, we clicked. I used JLabel to display image in get by using imageLabel.setIcon (new ImageIcon("default.jpg"));
  
  I need to draw the circle/rectangle when I click on the image that I need to select the different points of the image by drawing rectangles circles above the image.
  If you understand my problem, please guide me for the same thing.
  
  Thank you

  Create your own class that extends JPanel, substitute the paintComponent() method to draw the background image, then go through a list of points where the user has clicked (you'll need to track clicks too) and draw circles it.
  Stick this Panel in your get the label place.

  That's how I'd do it (then again once, I'm not big on Swing these days).