Need for the records at the beginning of bookmarks

Similar Questions

• How do I not what SATA driver do I need for the Satellite L300 - 03C

  How do I not what SATA driver do I need for the Satellite L300 - 03C so I can make nlite

  Hello

  Your laptop seems to be a Satellite L300 - 03C PSLB8C-03C01X.
  As already indicated on your first visit to thread the Toshiba Canada page and choose this model of laptop on the driver page.
  http://209.167.114.38/support/download/ln_bymodel.asp

  Then download the Intel Matrix Storage Manager (SATA) - image of floppy drive. It of for Vista, but the files in this package should work with Win XP too.
  Include these files using nLite to create the new disk Win XP that contains SATA drivers.

  Finally use this disk to start.

• What USB 3.0 card is needed for the HP Pavilion 6370t?

  What is needed for the HP Pavilion 6370 t USB 3.0 card?

  Hi Fasteagle,

  HP sells USB 3.0 PCI-E x 1 cards.  I have one in my HP e9280t.

• DVD how much we need for the files backup with backup and restore program?

  Hello how are you?
  DVD how much we need for the files backup with backup and restore program? Y at - it large differences in the time and space between write backups on DVD and external hard drive?

  I do not understand your question.  Asked how the space has been used on your C: drive and you answered 60 GB.  Now you say your PARTITION C: is 60 GB with only 20 GB used?  I really don't understand what you're so confused.  It's simple arithmetic grade 3rd.  What is space you USED on the C: drive, that multiply by 0.7 to obtain the amount of space will be used on your backup disk after compression.  Divide this number by 4.7 and round.  That's how many DVDs you'll need if you insist on the use of DVDs for backup.  Then

  (1) If you are using 60 GB, the answer is (60 x.7) / 4.7 = 8.936.  I rounded up to 9 and added 1 just to be sure.

  (2) If you use only 20 GB, the answer is (20 x.7) / 4.7 = 2.97 rounded up to 3.  Add 1 and get 4.

  If you use only 20 GB, I am very surprised, because almost any important installation of Windows 7 is going to take more than 20 GB.

  All of this assumes that you do NOT use the Windows backup and restore program, but one that I recommended.  When I used the windows one, the results were several times the space that I used on my C: partition.

  Good luck.

• replace my keyboard (ez4805US) and the need for the tech manual...

  I need to replace my keyboard (ez4805US) and the need for the tech manual... where can I find a...

  Welcome to the HP Forum!

  docwho wrote:

  I need to replace my keyboard (ez4805US) and the need for the tech manual... where can I find a...

  If you really want the manual, I think that would help to identify your laptop with full p/n.

  Identify the same way I did in my signature with the full p/n, alphanumeric included acharcters.

  Kind regards
  ERICO

• How to make a paper with some boxes to fill required for me to sign, and then some other boxes needed for the next person to sign. I want the boxes I've filled to be locked the next person.

  How to make a paper with some boxes to fill required for me to sign, and then some other boxes needed for the next person to sign. I want the boxes I've filled to be locked the next person.

  Hi johanb64152807,

  You can use eSign service, where you can send the document for signatures of several signatories, but the document will be sent to the following signatory after the earlier signed & it is not possible for him to make the changes.

  Documents KB for help: -.

  • Get started | Cloud of Document Adobe Tutorials
  • Quick Installation Guide | Services Adobe eSign
  • Send for electronic signature in eSign Adobe Document Cloud services | Adobe Acrobat DC tutorials
  • Send agreements and collecting signatures. eSign services
  • FREQUENTLY ASKED QUESTIONS | Services Adobe eSign

  Kind regards
  Nicos

• I can't get the file number I need for the license transfer process. Help, please.

  I can't get the file number I need for the license transfer process. Help, please.

  To the link below, click on the still need help? the option in the blue box below and choose the option to chat...
  Make sure that you are logged on the Adobe site, having cookies enabled, clearing your cookie cache.  If it fails to connect, try to use another browser.

  Get help from cat with orders, refunds and exchanges (non - CC)
  http://helpx.Adobe.com/x-productkb/global/service-b.html ( http://adobe.ly/1d3k3a5 )

• Windows Media Player does not open and I'm not find 'Turn windows features turn on or off' when I'm looking for the beginning. I need quick help.

  Windows media player not open yet

  Regarding "I'm not find 'Turn windows features turn on or off' when I'm looking for the start." ...

  Start > Control Panel > column to the left, choose Classic view > programs and features > column to the left, you will see turn windows features turn on or off the option. For the benefits of others looking for answers, please mark as answer suggestion if it solves your problem.

• Assistance needed for the registration of the application and store the values in a table

  Hello

  Hope that this explanation is not confusing. I explained my application you want in the text below and also attached a skeleton VI + screenshot hoping that he will clarify

  I try to do a VI that does the following:
  1. some code (blue Subvi) runs every 200ms
  2. every 200ms, a random number is generated
  3. the random numbers are stored in a table in intervals of time s 0.8 ("iterations")
  4. at any time, the (blue Subvi) code needs to have access to the random numbers generated in 'the previous iteration.

  To clarify, the iterations are as follows:
  Iteration #1: 0 - 1.8 s
  Iteration #2: 2 - 2. 8 s
  Iteration #3: 3 - 3.8 s

  Iteration #4: 4 - 4.8 s
  ..
  And so on...

  So for each iteration: the blue (Subvi) needs to have access to the random numbers generated in the previous iteration, for example:

  Iteration #1 (0 - 1.8 s): The blue (Subvi) Gets an array that contains only the zero (random numbers are recorded for the first time)
  Iteration #2 (2s - 2 8 s): The code gets an array containing random numbers of iteration #1
  Iteration #3 (3 s - s 3.8): the code gets an array containing random numbers of iteration #2
  Iteration #4 (3 s - s 3.8): the code gets an array containing random numbers of iteration #3
  ..
  And so on...

  At any given time in time;
  -The code gets an array that contains all the random, recorded during the previous iteration numbers
  -Values since before her previous iteration are ignored and not stored anywhere

  Thus, for example, to the #7 iteration:

  -The values during the iteration #6 are made available to the code in the form of a table

  -Values of #1 to #5 iterations have been deleted and not stored anywhere

  It is important that all values since before recording the previous iteration are deleted because they are not necessary because VI actaual will work for a long period of storage of numbers a lot more than I have indicated here

  Screenshot of the skeleton VI:

  

  I tried to play with the paintings, the structures of the case and the registers at offset, but everytime I try I get something wrong

  The skeleton VI is also attached (Iteration_VI and Code_SubVI)

  Any suggestions?

  Thank you!

  Yes, I agree that you need help.  First of all, you really do need to learn more about LabVIEW - spend a few hours with the tutorials, such as those mentioned on the first page of the Forums.  Oops - links to the tutorials which had been present for years seem to have been moved "elsewhere" with August 2016 LabVIEW community reorganization.  But look for them...

  Here are a few screws that basically implement what I described above (with some minor modifications).  First of all, this is a Top level VI which runs at 5 Hz (200 msec waits).  It starts with an array of 5 elements of 0, then once per second, this is replaced by a table of random numbers generated by the Random 5-table sub - VI 5 elements.  Note that I do not use a loop timed - those who are really designed for LabVIEW RT, but use the simplest functions on the Palette of the timer.

  

  Can't you see how that works?  The array to initialize on the left begins you with a table of 5 elements of 0.  The Timer inside the loop, it runs at 5 Hz, 'Index' counts 1, 2, 3,... to tell you where you are, and 5 shows you everything that lives on the shift register.

  Now sub - VI Random 5-table is supposed to do the following - if she was called to 5, 10, 15,..., it must return a (new) array of 5 random numbers, otherwise, it must return the array that was passed in.  So if all "works", table 5 shows 0, 0, 0, 0, 0 for the first second, a table at random for the second second (which is not superfluous!), a different for the third random picture second and so on.  I have already said a way to build this, but I chose a slightly different method (equivalent).

  

  Whenever it is called, a new random element is generated and added at the end of a (growing) random table stored in the shift register.  If size become 5, we send this Random-table-of-5 out through Out table and reset the register shift to an empty array.

  The case by default (when the size is not equal to 5) is shown below - we just return the array of entry to and accumulate new random table in full growth.

  

  These code fragments extracted from VI.  If you have LabVIEW 2016 (see the "2016" at the top right of the image?  This shows that it is a snippet of code LabVIEW 2016), you can open a blank diagram and drag this image, where magic OR converts it to a VI.  Otherwise, the code yourself and try out it.

  Caution - it is designed to run once.  If you run the program of high level, a second time, you may find that the new Random 5 - table appears to 0.4 ", 1.4", 2.4"(instead of 1", 2 ", 3").  I leave as an exercise for understand you to (a) why he is and (b) fix the code.  If you can't do that, then move an another 3-4 hours with the LabVIEW tutorials (or start playing with this code, edit it in some small way and to understand how it works).

  Bob Schor

• CC2014, why the need for the marker going to audition?

  These days I record a lot of my vinyl at the hearing, some for CD burning, some store in files. I like hearing, but one thing I find annoying and, if all goes well, there is a way to do better is that burn a CD or for export to files between each marker, I must address the beaches. This takes extra time and is unnecessary since the end of a range is the beginning of the next marker. However, at least for burning a CD, if I put the lines, it will burn the entire album with a track. Is it possible to simply place the markers and hearing recognized the fork between each marker automatically instead of having to manually set the beaches? It seems pointless for me like that.

  Thank you

  Sebasvideo wrote:

  This takes extra time and is unnecessary since the end of a range is the beginning of the next marker.

  This could be the case for you, but it is not necessarily for everyone. I, for example, changed lengths of inter-piste silence on a couple of CD test, and you could not simply do it without being able to define the periods of track regardless. But anyway, I am not sure what your problem is - everything you need to do is put a mark where you want that each track to start and the other at the end call button 'merge' and they all became will instantly. The additional time required to do this, compared to how long it will take to burn the CD in any case, is quite minimal.

  Or you didn't know you could do it like this?

• xw9400: xw9400. Pinout of the need for the connectors of the case (no psu connectors, only those in the case)

  I need the list of pins for various connectors case-Strip pin, especially J24 but other multispindle those too.

  Manual of Tyan S2915 Board for is a different version than that of poor quality that they OEM would be at HP for the 9400 and HP Tech Ref for the 9400 only provides pinouts for connectors well defined including pinout lie anywhere.

  The connector of the Panel before xw9400 J34 (there is no J24) pinout, the mother, is map:

  

  There are 2 key positions (lack of spindle) on pins 10 and 15.  Use these empty pins to help identify the signals.

  The pinout is very similar to other former workstations HP.  A few tips:

  -Pins 1 and 3 are for the harddrive activity led.

  -Terminals 2 and 4 are for the power light.  HP systems have back to back LED connected between these pins.  A green is on and functioning normal and red lights (and flashes error codes) when there are errors.

  -Connect a momentary between pins 5 and 6 switch will turn on the computer and off.

  -Connection of a momemtary between pins 7 and 8 switch will force a system reset.

  -PIN 9 is designated as + 5V, but it is powered by a 100 ohm pullup resistor to + 5V, so it will not provide a lot of power.  FOR INFO.

  -SPKR + and SPKR - are for the internal speaker.

  Most of the other connectors xw9400 follow standards of industry, i.e. the IDE drive and floppy connectors.

  Is there anything else you want to know?

• Need for the Satellite A21S-S4757 original wallapaper

  I have formatted by Satellite A21S S4757 & lost everything :(
  also I don't have a recovery disk can someone pls PM me with the wallaper origial of Toshiba for this model.
  Thankx in advance

  Uh, I really Don t understand why you need a wallpaper...

  Would it be better to have a disc of recovery instead of a wallpaper wouldn? So I guess you had a recovery disc hard and after that you´ve formatted the drive hard it's all over now.

  You now have the following choices:

  -get or get somwhere an installation of Windows with a working key, go to the [Toshiba Driver download site | http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp], download the drivers and install things together

  -look for the nearest available [partner service | http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT]
  in your country and ask them to sell you or at least help you with the problem of recovery

  -install linux ;)

  Who are your options, but you can also search for a user with the same machine and ask him to make a recovery for you to his picture disc.

  That's all.

  See you soon

• Satellite R630-13U - driver need for the WLAN/BT function key

  Dear Sirs,

  I have problem with my Toshiba Satellite R630-13U

  I have not found any driver for the wireless hot key windows 7 pro 32-bit to be able to turn on/off the wireless or Bluetooth.

  Thank you

  Ayman

  You need to install additional package from Toshiba. Several different tools, this package, and one of them is utility of Flash cards.

  Please install, test and post comments.

• Tecra M5 (PTM51E) - What tools I need for the FN keys?

  I am trying to install a new version of Windows XP on my laptop.

  Can anyone confirm which software from the support site, I need to install to get the Fn + F keys to work?
  I installed everything on the site but I can't get the buttons working.

  Screen brightness works but buttons to switch between WLan, WLan + Bluetooth etc do not work.

  Thank you for any assistance.

  Hello

  You can answer this question yourself as on the Toshiba site, you can find the installation instructions document. Use this list as an installation order recommended to work properly for laptop.

  In any case, for the FN keys, you need:
  -Common modules
  -Controls
  -Utility Hotkey for display devices
  -Utilities

  Good bye

• Satellite U200 - 10 H - pattern of the need for the sound card

  Schematic map his need for Satellite U200 - 10H.

  Microfone don't supply no work, there is a short circuit or an electrostatic.

  Hello

  I think that you will not find a schema to map his or your laptop. I've never seen such technical manuals on the Toshiba site and I think that they are not for the public and only for authorized service providers.

  If you have a hardware problem, you must contact the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  I have only good experience with my ASP. The technicians are very friendly and do the work as quickly as possible. :)