Need help to choose the correct setting in the virtual network Editor
This is my first time using machines virtual period. What I do is implementing a laboratory MCSE to follow certain CBT courses, I bought. I created a team of three virtual machines - two of them that are running WIndows Server 2003 and the other WIndows XP. The lab wants to use the following TCP/IP parameters for the three machines (Server1, Server11 and XP1)
Server1:
192.168 1,201
255.255.255.0
192.168.1.254
11 server: 192.168.1.211 (same gateway and subnet as Server1)
XP1: 192.168.1.1 (ditto for the door and the subnet as Server1)
Primary DNS is set to 192.168.1.201 (Server1 is DNS server).
Default VMWorkstation allowed me to ping both servers very well without any additional configuration. My problem is when I try to fix the DNS redirector on Server1. Any DNS server IP address that I plug in I could not get my XP box to get out of the Internet. I know it's a problem with my virtual network settings, I'm sure. Problem is I don't know where to start. Can someone point me in the right direction?
Thank you!
General things:
You cannot use the IP address ranges which are used somewhere else, and that the host might be able to see.
Type ' ipconfig/all' on the host and the glance to the adapter VMnet8. Suppose you see a 192.168.30.1 there. This means that your network VMnet8 address is 192.168.30.0/24 (24 =, displayed subnet mask as 255.255.255.0).
Your DNS and gateway for virtual systems would be 192.168.30.2.
You can check this in the editor of virtual network on the NAT tab.
To change the range of network addresses VMnet8 you must use the virtual network Editor.
1. go on 'host Virtual Network Mapping.
2. click on the ">" beside VMnet8 and choose "subnet".
3. change address you need. It's the network address, so the last digit (in your case!) should be 0. The address range should not be used elsewhere (physical network, VMnet1).
4. click on 'apply '.
5. When you click on the ">" again and choose DHCP or NAT you can see that all addresses have been changed accordingly.
When you enter ' ipconfig/all' to the host, you will see that the VMnet8 host adapter has an IP address of your selected range with 1 node address (e.g. 192.168.1.1).
The gateway and the DNS so its node address + 1 (192.168.1.2).
If you found this information useful, please consider awarding points to 'Correct' or 'Useful' responses Thank you!!
AWo
VCP / vEXPERT 2009
Tags: VMware
Similar Questions
-
Easy way to export and restore the virtual network editor in 10 workstation
I'm looking for an easy way back up and restore my settings of the virtual network Editor. I use Workstation 10.0.3 on Windows 7 64 bit and have several networks configured on different host machines. After Googling for the problem, I found the following:
-on a Linux host, the settings are stored in/etc/vmware/networking. However, I am not able to find the file in Windows. Source: http://serverfault.com/questions/535193/vmware-workstation-how-to-automate-or-script-changes-to-the-virtual-network-co
-on a Windows host, all parameters could be saved through export of certain keys in the registry. But these keys are at least partially unique on each host, and it would be a real pain to get the keys on each host individually. Source:
-vnetlib control should support a statement "-export" which creates a text file containing the necessary information. However if I try to run the command, as described in the link, no file is created on my machine. The command must be ' start/wait vnetlib.exe - export path_to_file' (I am running this command of in the workplace, of course installation directory). I also tried "vnetlib" - path_to_file to export, but that did not help either. I know that vnetlib works because I reinstalled successfully the vmx86 with vnetlib service - install. If also tried the vnetlib64.exe, but no luck. Source:
So is - someone of you knows how to solve my problem? I'm looking for a way to write a simple batch script that exports the settings without having to deal with the registry. My virtual network Editor loses its configuration from time to time and I don't want to set up everything by hand again.
Thanks in advance.
The instructions on my site still fit for WS 11
sanbarrow.com ~ Indexon a 64-bit host export settings like this
"C:\Program Files (x 86) \VMware\VMware" _-_ export f:\ws-networkbackup.txt
Note the syntax:
_ should be a space
-is not a unique dashboard but 2 x lessYou can import this backup again if you replace import export.
Use a commandprompt with high fees - (run as admin)The settings for the vmnetbridge service are stored in HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\services\VMnetBridge
The VMware DHCP written in
HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\services\VMnetDHCPThe NAT service written in
HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\services\VMware NAT ServiceThe vmnetuserif service is required, but there is nothing to configure
HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\services\VMnetuserifThere are also the vmnetadapterservice but there is nothing to configure
HKEY_LOCAL_MACHINE\SYSTEM\ControlSet001\services\VMnetAdapter
Less important entries go to
\VMnetLib HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\VMware, Inc.Also note for DHCP and NAT conf files:
netmap.conf
vmnetdhcp.conf
vmnetdhcp. Leases
vmnetdhcp. Leases ~
vmnetnat - mac.txt
vmnetnat.conf
They can be found in C:\ProgramData\VMwareFor your reference, I have attached a dump of vnetlib64.exe and the registry for the service vmnetbridge
Ulli
-
Impossible to change or remove networks in the virtual network Editor?
Hi people,
I try to change the address of Vmnet1 network IP subnet and remove Vmnet2.
The settings are changed correctly once I apply, but go back to the time when I reopen the virtual network Editor.
I tried to run 10 Workstation as an administrator and even a default restore does not remove Vmnet2.
Anyone know what I'm missing? Driving me crazy!
Thank you
romatlo
Hey just to be clear, I was referring to the virtual network editor shortcut or shortcut VMware Workstation no or vmware.exe vmnetcfg.exe! Are we on the same page?
-
Impossible to locate or select network adapters in the virtual network editor - W2K8 host
I am running VMware 2.0.1 on a W2K8 64-bit host (with the windows firewall is disabled for now). VM images are all able to start and use the network bridged the host connection. I can access these images of virtual computer on the network, and even each image virtual machine running on that host computer has access to the public network.
My problem is that I have three network adapters available on the host, but I can't individually select one of them in the virtual network Editor. The "Automatic gateways" checkbox is grayed, outside, tab automatic bypass, and if I try to select an adapter to exclude none appear in the dialog 'Add adapters excluded' that opens. In the virtual network mapping tab VMnet0 host, is set to be filled to an automatically chosen adapter and VMnet1 & 8 are configured to use their default VMware network cards. If I open the selections from drop down menu to one of the network adapter 10 VMnets listed in the virtual network mapping tab host there is no available alternative.
Note: three network cards available on my W2K8 host server, one of them is a fault tolerant team consisting of two individual adapters and two other network cards are not associated. The team of the adapter has a network on our local network connection, but the other two adapters are connected to a private network. The fact that the images of the virtual machine running on that host are available on the network and be able to use the network indicates to me that my VMnet0 connection automatically open is finding and using the adapters together somehow (Luckily, by design?).
I installed VMware 1.X and 2.0 on many host W2K3 servers and never encountered this problem before.
If Win2008 follows a similar to Vista security model, then you must run AS administrator virtual network Editor. Otherwise, you cannot make changes selections.
-
Can not see the physical adapters in the virtual network Editor
I installed VMware Server 2.0 on my computer running Windows 7 64-bit edition Home premium. I'm trying to make sure that the network card virtual vmnet0 only connects to my thread of material gigabit NIC, not my wireless card. I went into the virtual network editor and none of my physical computer network cards are listed. The bridge networks tab the checkbox next to automatically connect to the network device is checked and grayed out. Any ideas on why my physical network cards are not listed. Thank you.
Hello
Are you running virtual network editor with "RunAs as Administrator"?
-
"LAN Segment" option missing in the virtual network Editor
I regularly use isolated networks to test things. With the help of my own DHCP / DNS /... Server for 'infrastructure'
In 9.0.2 workstation there is an option "local network Segments. Miss me this option in 2013 of the workstation.
Why this option has been removed? Or was it an oversight? Or should I add something to my configuration?
Never mind.
'LAN Segments' option is not displayed in the network Editor, but it IS displayed on the virtual network adapter settings page.
I'm sorry.
-
I bought an Aspire One opportunity and need help to choose the right RAM upgrade.
I bought an Aspire One opportunity. On the device, the model number is listed as AO532h-2588. When I enter the S/N and look it up on the Acer website it is listed as AO532h-2Db. I want to move the RAM to 2 GB. Former model, then tried to keep the cheap. I see 200 pin DDR2 667 MHz PC2-5300 SODIMM as given common spec as far as RAM goes. Even through different products of PC. Is this all I get? That the annex-2588 or - 2Db question of difference in the review of correct choice? Thanks for your help!
I need to stick with 200 pin DDR2 667 MHz PC2 - 5300 SODIMM? Yes
But I can go up to 800 MHz. good. PC2-5300 and SODIMM is critical to search? No, but it will be worse to run (little).
Look at the essential link.
-
Need help to choose the dimensions of the file menu dvd
Hello all, I usually just wing when it comes to file size being put on video and then set above the video. As they are usually for my own videos and I don't really mind a bit wider.
However, this project is a concert paying top and I want it to be perfect.
I'm doing a menu dvd / overlays of text for this video
The video is 1920 x 1080 | by 1
Should I get pixels square in photoshop? PPI - it is my understanding that this is not serious digital project? also offers 16 8-bit color depth?
All the information you need are in your attachment. Pixel dimensions, 8 bits per channel and the frame rate also known as the fps (frames per second). The PPI is not relevant given that you do not print.
The pixel dimensions indicated in your attachment are for HD video. Just to let you know.
-
The best host that I have is a 2950 with 16 GB and I need to buy three more ESX host to be part of the cluster of 2950.
Wwhat should I choose which would be the last and the largest and still be compatible with the 2950 for vmotion?
Thank you!
R710 is a good choice and with EVC could be VMotion compatible with 2950 old without major problems.
If you need more CPU power to also consider R810 system.
If you need a lot of RAM check R910.
But (IMHO) the R710 is a good choice of Dell portfolio.
André
-
Need help to choose the material
I'm creating a new editing machine I want to use after effect, photoshop, flash, illustrator and 3ds max. I do a lot of animation 2d and 3d, video editing and graphic design.
It is the system that I'm currently planing on building:
Processor: intel core i7 2600 k (I'll be overclocking it to about 4.8 ghz)
Motherboard: Asrock p67 extreme6
Memory: G.Skill ripjaws x series 16 GB ddr3 1600 case latency 7
Graphics card: Gtx 570
Power supply: Rosewill bronze series 1000w
Hard drive: 4 x Corsair F120 in raid 0 (120gX4)
Case: Bitfenix collosus
CPU cooler: Noctua Nh - d14
I have a budget of $2500 for this computer. I was wondering if anyone has any suggestions on things should change / recommend a completely different version for my budget.
Also, I was wondering if the gtx 570 is a stupid choice and I should get a quadro 2000 instead. I don't do any game.
One last thing, do 4 ssd in raid 0 helps not at all or should I just get 8 HDD in raid 10 or I should spend less money on hard drives.
PS I know that the i7 2600 k was recalled but I'm in no hurry to build this computer. Also, feel free to recommend the hardware that has not yet been published, but will probably be in the next 8 months.
PSS all programs I listed are CS5.
A Quadro 2000 is not worth the money. The GTX 470/570 is more powerful and more attractive price.
SSD for storage don't deliver performance gains, but deliver an empty wallet. SSD for the OS disk do a little faster loading of programs, for the rest that they have no advantage.
Take a look at the following articles:
Adobe forums: RAID or not to RAID, this is the...
Adobe forums: Process without tape and Sandy Bridge or...
With potentially 8 disks for a raid array, I would not opt for a raid 10.
Assuming that 1000GO records
Number of disks Storagenet TB
Approximate transfer rate (MB/s)
RAID 10 8 4 350 - 400 RAID 3 8 7 600 - 660 RAID 5 8 7 600 - 660 RAID 6 8 6 480 - 550 The table above assumes raid controllers. Software raid or embedded raid are significantly slower.
RAID 3 or 5 lets you almost double the storage capacity and a much better performance. However the P67 platform does not allow that, unless the video card works at speed nearly half (8 x instead of 16 x).
-
Need help to access the internal network via VPN on ASA5505 8.4 (1)
Recently, I upgraded my ASA5055 from 8.02 to 8.4 and since I have updated to the new version I can access my home network is no longer through the VPN. I can connect to the VPN with no problems however I can no longer ping or you connect to my network of 10.0. Someone would be kind enough to look at my config and tell me what needs to be added to make it work? In my old config, I had a statement of NAT for VPN that is no longer here.
I also wanted to configure WebVPN to work as well, and this is something that I've never been able to understand. Is it also possible that I can be on my 20.0 network and connect to the VPN and access 10.0 as well? When it is connected to my network of 20.0 I'm not received credentials to connect to the VPN. I would be grateful if someone can help out me. The major part of this is the first part of this question.
My configuration:
ASA Version 8.4 (1)
!
ASA5505 hostname
domain xxxxxxxx.dyndns.org
enable encrypted password xxxxxxxxxxxx
xxxxxxxxxxxxxxx encrypted passwd
names of
nameserver 192.168.10.2
Office of name 192.168.10.3
name Canon 192.168.10.5
name 192.168.10.6 mvix
name 192.168.10.7 xbox
name 192.168.10.8 dvr
name 192.168.10.9 bluray
name 192.168.10.10 lcd
name 192.168.10.11 mp620
name 192.168.10.12 kayla
name 192.168.1.1 asa5505
name 192.168.1.2 ap1
name 192.168.10.4 mvix2
name 192.168.10.13 lcd2
name 192.168.10.14 dvr2
!
interface Vlan1
nameif management
security-level 100
IP address asa5505 255.255.255.248
management only
!
interface Vlan2
0050.8db6.8287 Mac address
nameif outside
security-level 0
IP address dhcp setroute
!
interface Vlan10
nameif private
security-level 100
IP 192.168.10.1 255.255.255.224
!
interface Vlan20
nameif Public
security-level 100
IP 192.168.20.1 255.255.255.224
!
interface Ethernet0/0
Description pointing to WAN
switchport access vlan 2
!
interface Ethernet0/1
Uplink port Linksys 12 description
switchport access vlan 10
!
interface Ethernet0/2
Description Server 192.168.10.2/27
switchport access vlan 10
!
interface Ethernet0/3
Uplink Eth1 management description
!
interface Ethernet0/4
switchport access vlan 30
!
interface Ethernet0/5
switchport access vlan 30
!
interface Ethernet0/6
switchport access vlan 30
!
interface Ethernet0/7
Description of Cisco 1200 Access Point
switchport trunk allowed vlan 1,10,20
switchport trunk vlan 1 native
switchport mode trunk
!
Banner motd users only, all others must disconnect now!
boot system Disk0: / asa841 - k8.bin
passive FTP mode
clock timezone PST - 8
clock summer-time recurring PDT
DNS server-group DefaultDNS
domain xxxxxxx.dyndns.org
network object obj - 192.168.50.0
192.168.50.0 subnet 255.255.255.0
Server network objects
host 192.168.10.2
network object obj - 192.168.10.0
192.168.10.0 subnet 255.255.255.224
network object obj - 192.168.20.0
subnet 192.168.20.0 255.255.255.224
network server-01 object
host 192.168.10.2
network server-02 object
host 192.168.10.2
xbox network object
Home 192.168.10.7
xbox-01 network object
Home 192.168.10.7
xbox-02 network object
Home 192.168.10.7
xbox-03 network object
Home 192.168.10.7
xbox-04 network object
Home 192.168.10.7
network server-03 object
host 192.168.10.2
network server-04 object
host 192.168.10.2
network server-05 object
host 192.168.10.2
Desktop Network object
host 192.168.10.3
kayla network object
Home 192.168.10.12
Home_VPN_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
outside_access_in list extended access permit tcp any any eq 3389
outside_access_in list extended access permit tcp any any eq 2325
outside_access_in list extended access permit tcp any eq ftp server object
outside_access_in list extended access permit tcp any any eq 5851
outside_access_in list extended access udp allowed any any eq 5850
outside_access_in list extended access permit tcp any any eq pptp
outside_access_in list extended access udp allowed any any eq syslog
outside_access_in list extended access udp allowed any any eq 88
outside_access_in list extended access udp allowed any any eq 3074
outside_access_in list extended access permit tcp any any eq 3074
outside_access_in list extended access permit tcp any any eq field
outside_access_in list extended access udp allowed any any eq field
outside_access_in list extended access permitted tcp everything any https eq
outside_access_in list extended access permit tcp any eq ssh server object
outside_access_in list extended access permit tcp any any eq 2322
outside_access_in list extended access permit tcp any any eq 5900
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access permit icmp any any source-quench
outside_access_in list extended access allow all unreachable icmp
outside_access_in list extended access permit icmp any one time exceed
outside_access_in list extended access udp allowed any any eq 5852
KaileY_splitTunnelAcl list standard access allowed 192.168.10.0 255.255.255.224
pager lines 24
Enable logging
timestamp of the record
exploitation forest-size of the buffer of 36000
logging warnings put in buffered memory
recording of debug trap
asdm of logging of information
address record [email protected] / * /
exploitation forest-address recipient [email protected] / * / level of errors
Management Server host forest
MTU 1500 management
Outside 1500 MTU
MTU 1500 private
MTU 1500 Public
local pool IPPOOL 192.168.50.2 - 192.168.50.10 255.255.255.0 IP mask
local pool VPN_POOL 192.168.100.2 - 192.168.100.10 255.255.255.0 IP mask
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow all outside
ASDM image disk0: / asdm - 641.bin
don't allow no asdm history
ARP timeout 14400
!
Server network objects
NAT (private, foreign) static tcp ftp 5851 service interface
network object obj - 192.168.10.0
NAT (private, foreign) dynamic interface
network object obj - 192.168.20.0
NAT (outside) dynamic public interface
network server-01 object
NAT (private, outside) interface static 2325 2325 tcp service
network server-02 object
NAT (private, outside) interface static udp syslog syslog service
xbox network object
NAT (private, outside) interface static service udp 88 88
xbox-01 network object
NAT (private, outside) interface static service udp 3074-3074
xbox-02 network object
NAT (private, outside) interface static service tcp 3074-3074
xbox-03 network object
NAT (private, outside) interface static tcp domain domain service
xbox-04 network object
field of the udp NAT (private, foreign) of the static interface function
network server-03 object
NAT (private, outside) interface static tcp https https service
network server-04 object
Static NAT (private, outside) interface service tcp ssh 2322
network server-05 object
NAT (private, outside) interface static 5900 5900 tcp service
Desktop Network object
NAT (private, outside) interface static service tcp 3389 3389
kayla network object
NAT (private, outside) interface static service udp 5852 5852
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
AAA authentication enable LOCAL console
AAA authentication http LOCAL console
the ssh LOCAL console AAA authentication
AAA authentication LOCAL telnet console
Enable http server
http 192.168.1.0 255.255.255.248 management
redirect http outside 80
location of SNMP server on the Office floor
SNMP Server contact [email protected] / * /
Community SNMP-server
Server enable SNMP traps snmp authentication linkup, linkdown cold start
No vpn sysopt connection permit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto-map dynamic outside_dyn_map pfs set 20 Group1
Crypto-map dynamic outside_dyn_map 20 set transform-set ESP-3DES-SHA ikev1
life together - the association of security crypto dynamic-map outside_dyn_map 20 28800 seconds
Crypto-map dynamic outside_dyn_map 20 kilobytes of life together - the association of safety 4608000
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
Crypto ikev1 allow outside
IKEv1 crypto policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH 192.168.1.0 255.255.255.248 management
SSH 0.0.0.0 0.0.0.0 outdoors
SSH timeout 30
Console timeout 30
access to administration management
dhcpd dns 24.205.1.14 66.215.64.14
dhcpd ping_timeout 750
dhcpd field xxxxxxxx.dyndns.org
dhcpd outside auto_config
!
dhcpd manage 192.168.1.4 - 192.168.1.5
dhcpd enable management
!
dhcpd address private 192.168.10.20 - 192.168.10.30
enable private dhcpd
!
dhcpd 192.168.20.2 public address - 192.168.20.30
dhcpd enable Public
!
a basic threat threat detection
statistical threat detection port
Statistical threat detection Protocol
Statistics-list of access threat detection
no statistical threat detection tcp-interception
Server NTP 192.43.244.18
Server NTP 129.6.15.28
WebVPN
internal Home_VPN group strategy
attributes of Group Policy Home_VPN
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol without ssl-client
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list Home_VPN_splitTunnelAcl
value by default-field www.xxxxxx.com
the address value IPPOOL pools
WebVPN
the value of the URL - list ClientlessBookmark
political group internal kikou
group attributes political kikou
value of 8.8.8.8 DNS Server 4.2.2.2
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list KaileY_splitTunnelAcl
XXXXXXX.dyndns.org value by default-field
username scottrog encrypted password privilege 0 xxxxxxxxxxxxxx
user_name john encrypted password privilege 0 xxxxxxxxxxxxxxx
username joek encrypted password privilege 0 xxxxxxxxxxxx
eostrike encrypted xxxxxxxxxxxx privilege 15 password username
username almostsi encrypted password privilege 0 xxxxxxxxxxxxxx
username ezdelarosa password xxxxxxxxxxxxxxencrypted privilege 0
type tunnel-group Home_VPN remote access
attributes global-tunnel-group Home_VPN
IPPOOL address pool
LOCAL authority-server-group
authorization-server-group (outside LOCAL)
Group Policy - by default-Home_VPN
authorization required
IPSec-attributes tunnel-group Home_VPN
IKEv1 pre-shared-key *.
type tunnel-group SSLClientProfile remote access
tunnel-group SSLClientProfile webvpn-attributes
enable SSLVPNClient group-alias
tunnel-group type ClientLESS remote access
tunnel-group kanazoé type remote access
attributes global-tunnel-group kanazoé
address VPN_POOL pool
by default-group-policy kikou
tunnel-group KaileY ipsec-attributes
IKEv1 pre-shared-key *.
by default-group Home_VPN tunnel-Group-map
!
!
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:438ed6084bb3dc956574b1ce83f52b86
: end
ASA5505 #.
Here are the declarations of NAT for your first question:
network object obj - 192.168.100.0
255.255.255.0 subnet 192.168.100.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.50.0 obj - 192.168.50.0
NAT (private, foreign) source static obj - 192.168.10.0 obj - 192.168.10.0 destination static obj - 192.168.100.0 obj - 192.168.100.0
And 'clear xlate' after the above and that should fix your first question.
I would check your second question and get back to you shortly.
-
Changing the connections of bridge without virtual network Editor
I wish I could change the bridged network adapter without using the virtual network Editor, i.e. via a script or VIX. COM.
The only files I found related to the virtual network editor are those located in the C:\ProgramData\VMware\, which none does not seem to allow me to specify the actual card to use in the bridge. While these files allow to specify which virtual network to use, I have to go a little further and change the real device for the virtual network. So instead of change between 'vmnet0' or "vmnet1", I need to change the NIC vmnet0 uses.
I am running VMware Workstation 8.0.4 on Windows 7 64 bit.
Thank you
Luke
On the Windows 2003 hosts, I used to do it like this:
net stop vmnetbridge
-then regedit key HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\VMnetBridge\Parameters\Adapters
-When does
net start vmnetbridge -
How to change the local IP on the virtual NETWORK adapter for Web server address
Hi all
I have a physical Windows system, on which I run VMware Workstation 9. Now on VMware I run Ubuntu 12.10 a LAMP for a Web server.Problem:Now, my local IP address for my NETWORK card virtual (using the Ubuntu one) at the address 192.168.159.7 and my router only emits the 10.0.0.x range IP addresses. So if I want to port forward to the virtual NETWORK adapter that has a 192.168 address, I can't, so my LAMP Web server are not accessible to the outside because the router does not send packets on port 80 to the virtual card... How to fix this?The only way I guess that is to be assigned an ip address of 10.0.0.x to the virtual NETWORK adapter?But how do I do this?I tried to do it on the host from the Windows machine with "get my IP address automatically", but she emits an 192.168 address every time...Thank youWelcome to the community,
I guess that the virtual computer is currently configured to "NAT" or "Host-Only' networking! That would explain the 192.168.x.x IP address.
There are 2 options to be able to access the web server on the virtual computer.
1. with "NAT" network configured
In this case forward port 80 to the IP address of the host and configure the port forwarding on the virtual computer in the "Virtual Network Editor. This way you can leave the IP address on the private network of 192 (if it is currently set to NAT)
2. use "Bridged" network layout
Reconfigure the virtual NETWORK adapter to the machine virtual networking "Bridged" within the parameters of the virtual machine, assign an IP address from your router network (10.x.x.x) and do the port forwarding on the router directly to the IP address of the virtual machine.
André
-
Need help to remove the zeros on the right
Hello.
I need help to replace the zeros in the string.
I have a string which is the output of the network packet. There are a few trailing zeros in the package.
I don't see them in normal mode, but the size of the string tells me that it's bigger then it looks like.
When I pass in hexadecimal mode, you can see zeros.
I tried to use the find/replace function allows you to search for 0 and replace it with an empty string constant. But, for some reason any, that he took no zeros.
I need to stop the string that follows * 69.
Show your code. You won't find and replace with all zeroes. These 00 in hex mode they are null characters. (not printable byte with a value of zero). You need search and replace on that character. (replace string should look like 00, when it is set to display the hexadecimal code.
-
Need help on choosing 11.1.2.3.500 or 11.1.2.4 for Hyperion planning project implementation.
Currently, we are debating on the following points, so need for expert advice, if someone have already done this.
- As all our previous implementation are on 11.1.2.3 500 and we know with certainty, it is stable
- 11.1.2.4 is fairly new in the market
That said y at - he already put 11.1.2.4 implemented for the PPP in particular, if yes how is the stability. As we have hard time have no place for the bugs that deals.
Thanks in advance,
Deker P.
I don't think that 11.1.2.3.500 for planning is massively different the 11.1.2.4 so for stability, they should be similar, the improvements are mainly around the simplified interface.
I would recommend going with 11.1.2.4, he is already on his third patch for the planning so I hope that all important questions will have been met, if there is a concern, then perhaps you should look at POC.
See you soon
John
Maybe you are looking for
-
I went in the messages app on my computer recently and discovered that more than 20 messages had been sent. The messages were all Chinese numbers and messages in Chinese. Everyone knows the same? my account is hacked?
-
Cards no-Quadro in a workstation Z1
The Z1 has a socket MXM 3.0 Type B for graphics cards. I talked to a guy from HP tech if HP BIOS to only limit cards Quadro MXM of HP and he said: they do not have. He also said that any 3.0/B MXM card should work, but HP offers no support for this +
-
Variable shared between PC and myRIO
Hi all I have a shared variable generated on a PC VI and I want to read this variable on a VI myRIO. I simplified it down to a simple generator of random numbers on my PC that updates all the 1 second and writes in a shared variable node. I then a ra
-
Computer Windows Vista won't standby automatically
I have Windows Vista. I had a problem because I put it to sleep and he "wakes" almost immediately. I've remedied that by changing a setting such that the network card might is no longer 'wake up' the computer. So I can now put to sleep manually.
-
7359 2-in-1: no sound from speakers after updating BIOs
Hi all Recently bought a 7359 2-in-1 and have been more or less satisfied - except for one glaring problem: there is no sound on the speakers (and despite checking all properties, etc.) after the last update of the BIOs Dell - WS - 01.08.00.exe. I sp