New Vista computer and router WRT610N

Similar Questions

• I have baught a new portable computer and you want to install windows vista (32-bit) on a bootable partition that it will be possible to do it with windows 7 (64-bit)

  I have baught a new portable computer and you want to install windows vista (32-bit) on a bootable partition that it will be possible to do it with windows 7 (64-bit)

  the laptop contained Home Basic windows 7 (64-bit) and I want to install windows vista Home premium (32 bit) on a bootable partition that it will be possible to do or tell me the parallel method to move a certain 32-bit operating system...

  I do not understand your question. If the laptop can run Windows Vista, it can probably run Windows 7 too.

  To run Windows 7 64-bit, the processor must be a minimum Core 2 Duo.

  System requirements:

  * 1 gigahertz (GHz) or faster 32-bit (x 86) or 64-bit (x 64) processor

  * 1 gigabyte (GB) of RAM (32-bit) or 2 GB RAM (64-bit)

  * 16 GB of disk space available (32-bit) or 20 GB (64-bit)

  * Peripheral figure DirectX 9 with WDDM 1.0 or higher driver

• I downloaded iTunes on a new laptop computer and he allowed. First of a süden, I can't sync my iPhone 6. What can I do?

  I downloaded iTunes on a new laptop computer and he allowed. All of a sudden, I can't sync my iPhone 6. What can I do?

  If your iOS device does not appear in iTunes, try the following:

  1. Open Control Panel > Device Manager
  2. Plug in your device
  3. Locate Bus USB Controllers > Apple Mobile Device USB Driver.
     It is also possible that the device may appear under imaging devices, portable devices or other devices or as a device USB of MTB.
     
  4. Right-click and select software update of the driver...
  5. Click Browse my computer for driver software
  6. Go to C:\Program Files\Common Apple Mobile Device Support\Drivers or
     C:\Program Files (x 86) \Common Files\Apple\Mobile Device Support\Drivers
  7. Click on let me pick from a list of drivers for devices on my computer
  8. Click on Apple Mobile Device USB Driver
  9. Click Next, then close and exit the Device Manager

  To step 3 above, open the Device Manager. Expand one of the articles that are listed.

  • USB Bus controllers
  • Imaging devices
  • Portable devices
  • Other devices

  Plug in the appliance. You should hear the telltale Windows sound device connection and a Division must acquire a new entry. This should be your device. It cannot be labelled properly at this point. If you do not hear a suspicious noise cable damaged.

  Or try If iTunes does not your iPad, iPhone or iPod - Apple Support Apple version of the above opinion.

  If not try a complete tear down and rebuild iTunes in accordance with the resolution of the problems with iTunes for Windows updates. 64-bit users might also try the build replacing iTunes for Windows (64-bit-for older video cards) which is sometimes a useful workaround.

  Or try to go back to the last version of iTunes that has worked for you. See the programs installation of iTunes to download links. If you roll back to 12.4.0.119 to 12.3.3.17 or 12.3.2.35, for example, then you will also need restore the database of the library in the manner described in the empty/corrupted after upgrade/crash iTunes library. The tip makes suggestions to reintroduce recent purchases, so at worst, you lose a few meters or a newly created playlist.

  TT2

• I have a windows vista computer and I forgot the password which he

  Original title: confused user

  Hello

  I have a windows vista computer and I forgot the password for it. I did a disk from rest of password for this computer.so, I used a disc to reset windows 7 and I have an error occurs whenever I have reset the password. What should I do?

  A Windows 7 reset disk does not work with Vista.

  What to do if you forget your Windows password:
  http://Windows.Microsoft.com/en-us/Windows-Vista/what-to-do-if-you-forget-your-Windows-password

  Microsoft's strategy concerning lost or forgotten passwords:

  http://support.Microsoft.com/kb/189126

• I have 6 LR on my desktop and notebooks (as the license allows). Just got a new laptop computer and uninstalled the old laptop, but now I get the error that I have to disable a computer before I can activate on my new machine. How can I disable an instanc

  I have 6 LR on my desktop and notebooks (as the license allows). Just got a new laptop computer and uninstalled the old laptop, but now I get the error that I have to disable a computer before I can activate on my new machine. How can I disable an instance that has already been uninstalled? Thank you!

  You are now logged for all activations.

  You can activate (sign) on 2 installations simultaneously.

  Let me know if you still have a problem.

• I have a new mac computer and want to transfer my creative cloud that contains lightroom & photoshop from a PC to a MAC. How can I do this?

  I have a new mac computer and want to transfer my creative cloud that contains lightroom & photoshop from a PC to a MAC. How can I do this?

  Sign in using your adobe id and install cc on your mac desktop app, https://creative.adobe.com/products/creative-cloud

  Use the desktop application to install your lr and ps.

• I need activate and install the Prime Minister on a new desktop computer and take it off my laptop that someone else uses at present. How can I do this?

  I need activate and install the Prime Minister on a new desktop computer and take it off my laptop that someone else uses at present. How can I do this?

  You can simply disable the activation of the laptop by signing out or Deactivate option: it is not necessary to uninstall.

  Learn how to enable or disable Adobe applications.

• I have CC on my laptop now have bought a new desktop computer and downloaded top CC, but failed to get a second organized plan

  I have CC on my laptop now have bought a new desktop computer and downloaded top CC, but failed to get a second organized plan?

  disconnect and then again on your desktop computer 2nd cc, sign, sign | Creative desktop application Cloud

  If this does not resolve the problem, attach a screenshot showing the problem.

• between my computer and router wireless connection (vista, premiem windows 7, 64 bit)

  Hey I recently had problems with my connection Wireless between my computer and the router.
  Normally off during the night is not connected to my router or on the internet the next day.

  I have been in close contact to my isp provider and have received a new router and reset my wireless Internet services provider site but I'm still having problems. I have also updated my drivers for my wireless on my laptop Hp G62 and have found that it will not cut when I do not shut down or sleep during the night.

  When you try to solve the problem, it will come back with "problem with the adapter or wireless access point and then asked to disconnect the power to the router. After doing this it will be fine all day.
  I do also to turn a blackberry 9000 "BOLD" and see first thing in the morning if the wireless is connected or not.

  ask for help, here is my last option I have been through everything and had an expert look at my computer where he found nothing wrong with my computer or wireless set up settings.

  any help or advice would be great

  Hello

  1. do you have problems connecting with Windows 7 or Vista?
  2. you remember of any change to your computer before the problem?

  Make sure that there is no interference between your router and your computer. For example. Mobile phones, like the mobile signals could conflict with your router signals and therefore no connection to your computer.

  You can uninstall and reinstall the Device Manager wireless network card.
   
  To uninstall the wireless device manager,
   
  a. Click Start, type device manager in the search box of start and press ENTER.
  b. Locate the network adapters and expand the same.
  c. Select the wireless connection, right click and choose uninstall.
  d. restart the computer, if prompted.
   
  Pilots should settle automatically after the computer restarts.

   

  Now you can install the latest wireless drivers and check if this solves the problem.

• Unable to show the XP on Vista computer and a few other networking issues

  Hello

  I tried to get my network set in place over the past two days without success.  The details of the network are:

  Main computer is under XP Professional SP3 with the printer and the router connected to it.  I also have a laptop running Vista professional that connect wirelessly to the router.  I am able to ping the desktop from the laptop, but not vice versa.  Both computers have the same subnet and default gateway address.  By reading some troubleshooting, it was advised to run the microsoft patch to install the LLTD Responder on the xp machine I did.  I can see the files in the subfolders, but when I run services.msc program is not for me to start.    Desktop and laptop computer are in the same workgroup.  Before you install the hotfix, I could see the laptop from the network to the desktop but now I can't.  I also noticed that even if I have the LLTD my laptop configured to start automatically, it is not this.  In fact, it seems to stop automatically, and I have to restart the service.

  I also try to put in place so that I can print from my laptop and my ipad sharing printer.  The printer and the desktop are set to share printers, but I can't find it on the laptop.  I'm assuming that once I see the desktop on the network it 'may' reslove this problem.

  Anyone have any ideas on what I can do to solve the problem?  I can always connect all computers to the internet. I also see the two computers on the network when I run the network configuration in norton 360.

  Thank you very much

  Emily

  N ° if it never works, then a firewall is not your problem.  Remember that Microsoft Networking can take up to 15 minutes to find a new devices on the network.  If it does not appear and you want to speed up the process a bit, try to search for the computer...

  Start-> Search-> [for files & folders (the classic case)]
  then, down in the section 'Search other elements', select 'computers '.
  Enter the name of the other computer, and then click "search now".

  This launches a pretty aggressive search for the other computer.

  HTH,
  JW

• Problems with new cable modem and router

  Long story short, that my cable modem went bad.  I replaced it.  Now the two computers cannot connect to the internet.  It gives me a DNS error, saying that they can not find the server.  However, I can get on the internet if I hang the right modem to computer with courses through the router. I got it with the new modem a few days of work and use of the router, but now it does not work.

  There are 2 computers on the network, the two runnning vista.
  a linksys router model number BEFW11S4 ver 4.
  and the motorola surfboard SB5101 modem.  the old modem was a surfboard SB5100 motorcycle.

  There's a btn reset on the router (often the metal clip through a pin hole)
  Everything also its possible allways the router is bad

• I am trying to troubleshoot a Vista computer and get obtain an IP address

  tried both wired and wireless adapters - get 'a Local access only?

  Hello

  Thanks for the post. Unfortunately, the question is not clear. To understand the question answering these questions.

  1. What exactly is the problem that affects the computer?
  2. What troubleshooting steps to try? and we already tried?
  3. What is the full and exact error message?

  Try the methods provided and see if it helps to solve the problem.

  Method 1:

  Start the computer using safe mode with networking, try to access the Internet and check if the problem occurs. Check out the link.

   

  Startup options (including safe mode)
  http://Windows.Microsoft.com/en-us/Windows7/advanced-startup-options-including-safe-mode

  Method 2:

  If the problem does not occur in Mode safe mode with networking and then start the clean boot computer and check if any non-Microsoft services is causing a conflict for the problem to occur. Check out the link.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  http://support.Microsoft.com/kb/929135

  Note: once the diagnosis is made, follow step 7 of section to configure the computer to start the Normal start.

  Method 3:

  Check the link and try the steps of troubleshooting described in the article.

  Network connection problems

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-connection-problems

  (The steps apply to Windows 7 as well)

  Method 4:

  You can also try the steps outlined in the article that the link refers to:

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• I AM TRYING TO INSTALL ADOBE PHOTOSHOP ELEMENT 10, BUT IT IS A NOTE SAYING TO GET ADOBE SUPPORT ADVISOR, I TRIED THEY SAY IS NO LONGER SUPPORTED, BOUGHT THE LICENSE AND A NEW APPLE COMPUTER AND THE NEED TO INSTALL

  I AM TRYING TO INSTALL ADOBE PHOTOSHOP ELEMENT 10 IN A NEW APPLE COMPUTER, BUT THERE IS A NOTE SAYING THAT THE INSTALATION FAILED TO INITIALIZE, AND THAT I SHOULD DOWNLOAD ADOBE SUPPORT ADVISOR TO DETECT THE PROBLEM.  I DID IT, BUT HE SAYS THAT IT IS HAS BEEN DISCONTINUED.

  start at the top and work your way down to apply applicable patches until your problem is solved.

  If (win) cc: https://helpx.adobe.com/creative-cloud/kb/creative-cloud-desktop-application-failed.html

  If your error is:

  "Setup failed to initialize. File not found. ' or 'could not initialize installation. This could be due to missing files.

  first of all, rename folder OOBE OOBE.old.

  to find the OOBE:

  Win 64 bit OS: Program Files x86\Common Files\Adobe\OOBE

  Win 32 bit OS: Program Files \Common Files\Adobe\OOBE

  Mac os: HD > library > application support of > adobe > caps

  Mac os: USER > library > application support of > adobe > OOB

  If it fails or isn't the exact error you see, uninstall, clean (http://www.adobe.com/support/contact/cscleanertool.html) and reinstall.

  If you use an installation dvd:

  Copy the contents of the drive in a desktop folder and install from this directory.

  If you are using a mac:

  1. try to create a new user account in Mac with administrator privileges.

  2. connect to the new user, navigate to Mac HD > Application > utilities > Adobe Installer folder, locate products such as Adobe Reader, Adobe Flash, Adobe Air and uninstall the

  3. navigate to the user library > Application Support > Adobe and Adobe put in the trash.

  4. navigate to Mac HD > library > Application Support > Adobe and Adobe put in the trash.

  5 restart the installation.

  If everything is applicable above fails, check your Setup logs:

  http://helpx.Adobe.com/Photoshop-elements/KB/troubleshoot-install-using-logs-elements.html

• Help on the portable computer connection on the desktop and router WRT610N

  I just bought a WRT610N and have loaded in my office which is not wireless and connected to my cable modem and the router on the desktop so that I can get the Wi - Fi of my wireless control internal Laptop Dell Insperion 1501.  My laptop shows my network I have install on the desk top and there are 4 bars green connection excellent, but it does NOT connect to the INTERNET.  How can I fix it?    Please help me sooooooonnnnnnnn.   Thank you very much.

  Try this,

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER...
  Let the empty user name & password use admin lowercase...
  For wireless settings, follow these steps: -.
  Click on the Wireless tab

  2.4 GHz wireless settings:

  -Here, select manual configuration... Wireless network mode must be mixed...
  -Provide a unique name in the name box of the wireless network (SSID) in order to differentiate your network from your network of neighbors...

  -Set the Standard - 20 MHz Radio band and change the Standard channel to 11-2, 462 GHz... Wireless SSID broadcast should be enabled and then click on save settings...
  Please take note of the name of the wireless network (SSID) because it's the network identifier...
  For wireless security: -.
  Click the sub-tab under wireless > Wireless Security...
  Change the mode of WEP wireless security, encryption must be 64-bit. Let the empty password, do not type in anything...
  Under type of WEP Key 1 in all 10 numbers please (numbers only and no mailbox for example: your 10-digit phone number) and click on save settings...
  Please note the 1 WEP key as it comes to the security key for the wireless network...

  Click the settings advanced wireless
  Change the interval of tag to 75 > change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...
  Now let's see if you can locate your wireless network and try to connect... Make sure your wireless connection is st to obtain the IP address automatically.

• After the update and restart my computer was like a whole new vista version and the version of office business. All files and emails and contacts and other programs have disappeared!

  I did a system restore to run today.  He had updated 8 minutes before all this happened, but I couldn't say what update caused this.  It's important, so I guess that vista.  All of my Web site and software adobe software for forms and emails, files, photos, everything disappeared as if today, I bought the computer Office exccept was there, but empty. I have even been asked to set up an e-mail account.  I don't know how it happened with an update and cannot lose another day to such a waste of time. I work and am finishing my doctorate so the stability of my work being it is quite serious.  How this happened and how can I keep it doesn't happen. I backup to carbonite.com and have now checked, contacts, emails by the intermediary of today and all the files, but it's scarYYYYY!   I was never warned or the ability to restart or given in error messages.

  Hi Kelly Barr.

  Welcome to Microsoft answers forums!

  Are you referring to (files, emails, contacts and other programs) shortcuts on the desktop?

  When updates are installed on the computer it says system files, this process of service not Microsoft that are running in the background can conflict with updates and tour damage the system settings.

  This problem can also occur if system files are corrupt.

  Try the following in order to recover the desktop icons.

  Even though the desktop icons disappear, the programs are still installed on computer you can launch them.

  Method 1:

  Ø, right click on the desktop

  O select view

  Ø, click show the desktop icons

  Method 2: Click the Start button > select programs > verify if all the programs installed on the computer display > try to start or right click on the program and Select create a shortcut

  Check the updates that triggered this question go by the date.

  1. Click for Start > Control Panel > Classic view > Windows Update.

  2. along the top, click view update history.

  Before you install updates, follow the precautionary steps listed below.

  Step 1: Disable the security software on the taskbar

  Note: Activate security software once theupdates are installed.

  Step 2: Disconnect external devices like printer and scanner, except the mouse, keyboard, and internet connection.

  Step 3: The clean boot computer:- Perform a clean boot (check step 1 in the link)

  http://support.Microsoft.com/kb/929135 ---> how to solve a problem by performing a clean boot in Windows Vista or in Windows 7

  Important: n ' forget not to put the computer to a normal startup after you install updates. Follow step 7 in the link.

  Try to install updates via windows update or you can also download and install the updates manually by accessing the Microsoft Web site.

  Data backup on the computer

  You can use backup and Restore Center integrated in the operating system to back up data.
  http://Windows.Microsoft.com/en-us/Windows-Vista/back-up-and-restore-frequently-asked-questions

  Thanks and greetings
  Ajay K
  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.