No boot device available on a desktop XPS720.

Similar Questions

• Dimension E310-NO BOOT DEVICE AVAILABLE!

  I tried to install a new 320 GB HDD, internal, in my Dimension E310 desktop environment, but I get an error message that reads, "floppy seek failure" on the 1st line, & below it reads "No Boot Device available, strike F1 key to reboot, F2 for Setup utility".

  Ive done hard drive tests that pass.  According to a Dell support link, so it could b a software problem.  I have to buy another software?

  The model starts just fine if I reinstall the old hard drive.

  I bought this model in ' 05, 6 to 8 months later would not start then a supporter of Dell Tech ran me through a reprogramming of the model.  Since the Ive started then every time the comp Ive had to press F1 for her to run, & Ive not had any problems since.

  How can I use my computer to work normally with the new hard drive?

  
  

• When I try to power to the top of our Dell computer, we get a black screen and the message "boot device available. Press button to try again. »

  Pressing enter does nothing, then it usually starts by pressing "ctrl-alt-delete."  The computer runs VERY slowly.  We have Windows XP and also just downloaded Safe Eyes software McAfee, but it was slow & have start questions for a while.  My son also downloads a lot of PS3 games, etc.  Who would have something to do with it so slow?  Is there something we can do to clean it ourselves instead of redoing it to Best Buy and pay $100?

  Hello

  Start are what problems you referring?

  Method 1: May be that the hard drive is not detected. Boot to the Bios Setup and make sure that the first boot device is defined as hard drive and also make sure that save you the settings and check what is happening.

  If your computer is not configured to boot from a DVD, see the documentation provided with your computer. You may need to change your computer's BIOS settings. For more information, see BIOS: frequently asked questions. For assistance, contact the manufacturer of your computer.

  Warning of the BIOS:

  BIOS change / oxide of additional metal (CMOS) semiconductor parameters incorrectly can causeserious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  Method 2: If you are able to boot to the desktop then try to perform the clean boot on the computer to resolve the performance issue.

  From your computer by using a minimal set of drivers and startup programs so that you can determine if a background program is interfering with your game or program. This type of boot is known as a "clean boot".

  Reference:

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  1. click on Startand then click run.

  2. type msconfigand click OK.

  The System Configuration Utility dialog box appears.

  3. click on the general tab, click Normal startup - load all services and device drivers and then click OK.

  4. When prompted, click on restart to restart the computer.

  The following articles could be useful.

  Slow PC? Optimize your computer for peak performance

  http://www.Microsoft.com/athome/Setup/optimize.aspx

  How to make a computer faster: 6 ways to speed up your PC

  http://www.Microsoft.com/atwork/maintenance/speed.aspx

• my laptop can not get the boot device

  When I turn on my old laptop, it goes to bios and saying: no boot device available strike f1 to not to retry boot, f2 configuration utility, no other options. all get any idea for this problem thx allllllllllllllllll

  Hi isaaq,.

  It may be a loose cable connection or the drive may have failed.

  Since it is a laptop, the support option are limited.

  Depending on the age of the PC, you can contact the manufacturer to see if there is a diagnostic program.

  According to the OEM, your recovery disc can have a method of repair installation if it is not hardware fault.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• How can I fix this error? Available boot device. YOUR 0: Installed; YOUR 1: Installed; YOUR 2: None; YOUR 3: no

  I can't use my desktop pc, because this message appeared when I started my pc since the closure.  Help, please!   I'm not very computer savey.

  The message should look like this:

  No available boot device:

  SATA 0: installed

  SATA 1: installed

  SATA 2: no

  SATA 3: no

  This means that there is a problem with your hard drive. If, in addition, the message is not be displayed correctly, there must be something else wrong with your computer. You will need to bring to a repairman.

• In Safari, I get the error code BSO D 0 X 80060402, error code Windows defender in the available boot device. He told me to contact Microsoft certified technicians. I do not use Microsoft or windows.

  In Safari, I get the error code BSOD 0 X 80060402, error code Windows defender in the available boot device. He told me to contact Microsoft certified technicians. I do not use Microsoft or windows.

  You have utilities installed on the computer antivirus, cleanup, or other third party maintenance?

• When I re-startup I get a message "no available boot device - HDD internal.

  Original title: start the problem.

  Recently, my computer hangs in.  Sometimes, when I re-startup I get a message "no available boot device - HDD internal. Can someone tell me what this means? (Doesn't look good!)

  This probably (should) means that your hard drive is dying

  Try this if you can initialize

• "Boot Device not available" when starting cold laptop Dell Inspiron 8200 with Win XP.

  "Boot Device not available" when you power on a Dell Inspiron 8200 with Windows XP.  Repeated restart attempts after Windows starts.  Once in Windows, I can restart repeatly with no problems.  The "Boot Device not available" only occurs during a cold start the PC.  Any help is appreciated.

  Malkeleah,

  Thank you!  Unfortunately, the laptop is 8 years old and is no longer under warranty.  With your guidance, I'm going to explore repair or replace options.  Best wishes to you...  Taylor

• VISTA - no available boot device

  On my VISTA - I can't get my computer to turn on. I get a black screen with the following message:

  No available boot device

  SATA 0: NO
  SATA 1: NO

  SATA 4: NO

  SATA 5: NO

  I already tried all connections many times. The DSL modem works fine, all lights indicate it anyway. We have unplugged and plugged all the links back in and the only thing we did different since we bought it is y add a DVD burner. (plug and play) Can anyone HELP? Thank you

  Hi, LT.

  I suggest you go into the BIOS and change the boot device of whatever it is (it looks like floppy drive) on the hard disk in the list of bootable devices.

  You will need to read the manual that came with the PC for additional instructions.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• 0xc000000e no available boot devices

  My computer crashed about an hour earlier and from the beginning he said he

  No available boot device

  SATA 0: no

  SATA 1: no

  SATA 2: no

  SATA 3: no

  It won't let me access the start menu through the splash screen

  My computer is a Dell Inspiron from 2005-06 with windows 7

  Sounds like the drive has failed.  You will probably need to buy a new one and load Windows and software on it.

  I hope that your personal files are stored on an external...

• PowerEdge 2500 - no available boot device

  I'm trying to revive an old Poweredge 2500 that starts up with the error: no available boot device, press F1 to retry or F2 to enter Setup utility

  I have 3 drives on the SCSI channel Hot and also have a CD ROM on this channel too

  I set the boot sequence to boot to CD Rom first, so that I can maybe just install Windows Server 2008 and get things up and running

  But it is not booting to CD ROM. its just commissioning and turning the device No. Bot available

  Is this dead or can I revive somehow? Thank you

  Server 2008 DVDS only and I doubt that any 2500's never delivered with DVD players.  You should be able to boot from a CD of 2003.

  Is there a BONE here, you want to fix it?  If so, do you have RAID (PERC 3/Di) activated in a RAID 1 or RAID 5?

• No available boot device?

  Unlike so many others on this site, after you receive the message "No boot device - insert boot disk and press any key", I don't then enter my mac no matter what buttons I press. I have a macbook air 11 inches, but I do not know the details because of this problem. If a boot disk is a physical disk, then I don't have a hard drive! What should I do? I literally have an essay due in the next few days, and it's on my laptop! If I can't open windows more, is well, because at this point, I want to just my mac back. Please help me, I'm desperate!

  You should be able to boot OSX by holding down the alt/option directly key after hearing the startup sound (the "bang... »). Keep holding it until you see the disks that you can start with. One of them should be the Macintosh HD disk that contains your OSX installation. Select that drive and press ENTER. Then, your mac should start to OSX. Good luck!

• How do I repair: windows7 error reboot and select proper boot device?

  My computer is about 2 years old.  Sound works just fine.  One morning, I started it up and a black screen came with: reboot and select proper boot device or insert boot media in selected boot device and press a key.  Any key you hit it just kept announces the same message, I had to tough out.  As long as I start the computer with Del, F8 or F10, I can get the computer to boot. No matter what I change, it works for a few times then goes back to the same error.  Also it will not always wake up after he falls asleep.  I tried to do a repair of systems, but it does not work

  Hello

  1 do you have made no changes to software before this problem?

  2. you have the Windows 7 installation disc?

  3. what changes did you and have you been able to boot to the desktop after that?

  Method 1:

   

  I also suggest you to try the other options of WINRE (Windows Recovery Environment) and check.

  What are the system recovery options in Windows 7?

  http://Windows.Microsoft.com/en-us/Windows7/what-are-the-system-recovery-options-in-Windows-7

  Method 2:

  I also suggest you to check the drive for errors that it can cause a Windows to boot.

  Follow this step to do the same thing:

  1. Click Start
  2. Type: CMD, according to the results, right-click CMD-> click on "Run as Administrator"
  3. At the command prompt, type: chkdsk /r

  When you restart your system, your computer will be scanned for errors and will try to correct them.

  Note: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data can be lost.

  Check a drive for errors

  http://Windows.Microsoft.com/en-us/Windows7/check-a-drive-for-errors

  The issue can also occur if the boot device is not correctly defined in the BIOS. Make sure that the hard drive where Windows is installed is selected as first boot device.

  Note: Changing the BIOS / semiconductor (CMOS) to complementary metal oxide settings can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the configuration of the BIOS/CMOS settings can be solved. Changes to settings are at your own risk.

  See also:

  http://support.Microsoft.com/kb/266283

• El Capitan "Don't Update" no boot device

  Hello

  I've updated updated my MBP 2011 end of El Capitan, and now I'm unable to start Windows. The Bootcamp partition is always visible in disk utility, but if I try to start it I get a response of "no boot device."

  Here is my disk configuration:

  

  You can use Re: [help] can't start Windows (8.1) after partition resizing as a reference and rebuild your MBR using GPT Fdisk?

  GPT Fdisk is available at https://sourceforge.net/projects/gptfdisk/ .

• Boot camp is no boot device

  Hello community,

  I used to read every forum/discuss before posting, so it's the first time here.

  My config:

  Mac pro 3.1 2008 / Mac osx 10.11 / Boot camp 5 / windows 7 update to windows 10

  I have installed since a year now Bootcamp, windows told me I was able to update windows 10, and they were little good cause I managed to update without any problem, I used windows 10 for a month and have never encounter the difficulties in moving an OS x and windows.

  But yesterday, I needed to format my disk HARD school wich has been used for time machine. Time machine has been disabled for months (because it was full and keeping saying that it was impossible to save) and I needed a free space to use with Windows 10.

  I deleted and format FAT32, this secondary hard drive, so I could not boot into windows, keep showed a black screen with flashing white guest and not any something key.

  If I go to select a restart from a drive, I can choose OS x or bootcamp.

  I can see my partition boot camp on OS X with all data still there, but when I push the button option at the beginning, I have only 2 choices: - Mac OS X - or - restore 10.11 - I don't see my windows startup.

  I tried to download parallels desktop to see if he is able to start my training camp. But parallel shows me "no boot device."

  Can someone help me?

  Thank you.

  Here is some information on installed drive:

  diskutil list

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 500,1 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS Macintosh HD 350,2 GB disk0s2

  3: disk0s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 149,0 GB disk0s4

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 160.0 disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Microsoft database disc2 159.8 GB disk1s2

  / dev/disk2 (external, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: FDisk_partition_scheme * 4.0 GB disk2

  1: DOS_FAT_32 DISK_IMG 4. 0 GB disk2s1

  ________________________________________________________________________________ ___

  sudo fdisk/dev/disk0

  Disk: geometry / dev/disk0: 60801/255/63 [976773168 sectors]

  Signature: 0xAA55

  From end

  #: cyl hd s - cyl hd s id [Start - size]

  ------------------------------------------------------------------------

  1: EA 1023 254 63 - 1023 254 63 [1-409639] < unknown ID >

  2: AF 1023 254 63 - 1023 254 63 [409640-684078336] HFS +.

  3: AB 1023 254 63 - 1023 254 63 Boot Darwin [684487976-1269536]

  04:07 1023 254 63-1023 254 63 [685758464-291014656] HPFS/QNX / TO THE

  ________________________________________________________________________________ __

  sudo TPG - v - r see the/dev/disk0

  See the TPG: / dev/disk0: mediasize = 500107862016; SectorSize = 512; blocks = 976773168

  See the TPG: / dev/disk0: MBR suspicious to sector 0

  start index size summary

  0 1 MBR

  1 1 Pri GPT header

  2 32 table GPT Pri

  34 6

  40 409600 1 part TPG - C12A7328-F81F-11D2-BA4B-00A0C93EC93B

  409640 684078336 2 part TPG - 48465300-0000-11AA-AA11-00306543ECAC

  684487976 1269536 3 part TPG - 426F6F74-0000-11AA-AA11-00306543ECAC

  952 685757512

  685758464 291014656 4 part TPG - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7

  976773120 15

  976773135 32 table dry GPT

  976773167 1 dry GPT header

  Please remove all drives (internal and external) except the Windows disk after having properly stop your MP.

  A. we need to disable SIP.

  1. boot in local restoration (command-R).

  2. start utility-> Terminal.

  3. type csrutil disable in the Terminal, and then press enter/return.

  4. type csrutil State.

  5 start normally, then type csrutil status to confirm that all of the individual entries are still disabled.

  B. fix the Windows MBR Boot-ability entry. Please ignore the i386 MBR error message, but not others

  sudo fdisk e/dev/disk0

  p

  setpid 4

  07

  Pavilion 4

  p

  w

  There

  Restart and test.