No visible mask values?

I have a bit of a problem with masks. It seems that I can't change the values of the pen, the opacity, the expansion... anything really. The values are simply not there. Has anyone encountered this problem?

See the image below:

I use a computer laptop HP, AE 13.5.1.48 running

Thank you!

You have hidden column. Right-click in the column header and turn it back on. Looking for the Modes column or switches.

Or - go to the lower left corner of the timeline and click on the first icon to expand or collapse the Panel layer Switches

Tags: After Effects

Similar Questions

Make the visible property values in the timeline

I started doing basic AE tutorials. I must have done something that makes the values of the properties in the invisible timeline. Now to change a value, I with the right button of the property and go to change the value. Can someone, please?
Thank you
Borgie

Right-click on the column headers and/or toggle the display of column with F4.

Mylenium

Importing data from XML form in hidden form fields & making it visible if the book value

Hello:
I export the data in the form submitted, and important in the 2nd-> 3-> etc... Forms, however, a lot of these areas, I want to be kept hidden, unless they have a value. When I import data from field of forms 1, it will be smooth, however if the fields are hidden, you must go through the selection of checkboxes to make it visible again or just do all visible all the time. I was wondering if there is a feature or coding that would go in the direction of: Once imported XML favorite on click on the button "Update fields", go through fields and if hidden fields now have a value do what subform/Sub-sous-form Visible.
The reason is that if you do have an incident report form which can take 10 names of employees, but only 2 were involved in an incident, it would look very cluttering on the survey form, if there are 10 fields name employee, 10 fields, 10 fields of plane location, etc... But only 2 employees have been involved in a minor incident on the incident report form which does not imply anything else.
Any suggestion or help would be greatly appreciated and thanks for gratefull to any answer.
Nicely,
Al

Thank you for pointing me in the right direction... A little elbow grease, of coffee, patience, and did I mention the patience and the following works without fault

Created at the mouse from the export button:

xfa.host.exportData("",0)

The button import of other form value:

xfa.host.importData)

See the sections "Check boxes" to see if this article is supposed to be visible and makes visible the value of import form form: Ready:

if(Button_DelDep.RawValue == 1)

{

Del_Dep.presence = "visible";

}

if(Button_DelArr.RawValue == 1)

{

Del_Arr.presence = "visible";

}

if(Button_Div.RawValue == 1)

{

Div.Presence = "visible";

}

if(Button_MADiv.RawValue == 1)

{

MADiv.presence = "visible";

}

if(Button_DelDepXD.RawValue == 1)

{

Del_DepXD.presence = "visible";

}

if(Button_Other.RawValue == 1)

{

Other.Presence = "visible";

}

Graph and node property

Hello all;

I want to do my most powerful .vi, so what I wanted to do are the following:

1. my entry should be: "checkbox system Boolean" table 1 d (it's must have, I need this as input in the function call library node)

2. all these checkbox (12) are connected to the graph (in this example, I chose 12 graphs and a signal input which is the same, in real time, I have different signals, the scales...)

What I wanted to do when I check the first box, first graph will appear (and on the graph will display its name, which is identical to the box). And then for example if I choose will be 3,5,8 checkbox graphic 3,5,8 which will follow one after the other and so on;

I started making table 1 d box, but after I group all together and try to rename it for example check box 1 for channel 1, is to change all names not only those who I have renamed it. I know that I can use 'property node' and choose 'visible' and 'value', but I don't know how to implement together and also move graphic one after the other, if I choose for example 1,5,8 channel.

I attach test file and photo;

Thank you

Look at this.

This makes the Cluster to table as I talked earlier and locates also each chart based on a table of positions.

How to create events on the cursors-waveform?

Hello

I have a form of wave-graph with the sliders-field. In the field of sliders, I can add new sliders or activate one of the existing sliders by clicking on its name.

In the VI manages an event structure in a loop.

Now, I have two questions about this:

1. is there an event that I can grab when "a new cursor is added? (Inside the event, he must then the cursor automatically be centered.)

2. is there an event that I can grab when ' a cursor is activated / assets has changed? (inside if the event I want to then move cursor symbol to "cross" to move the cursor, if it was before the zoom symbol.)

Thanks for the help

Hi OnlyOne,

attached is the vi saved in LV8.5

Currently I m looking for a "Bring-to-Center" - property I can run inside the event.

This exists?

This property is not available I guess... but you can get by setting the property "cursor position" If you know the length graphic visible (x, value y)

same structure

Hi all

I have trouble getting a structure of the event to save changes in value on control Boolean and enumerated types when their values are changed using a called invoke node to a separate VI rather than via the interaction of the user in the same VI.

I have a control VI that the user interacts with... and a VI display connected via a reference Server VI which contains a video playback, but normally without user interface.

When the user changes a Boolean value in the control VI, the Boolean value changes of the VI of control and this change is reflected in the VI of the display. However, the event to change the value for this Boolean IS NOT saved in the VI of the display. If you manually change the value in the display VI, after the control visible, the value for this Boolean Change event IS registered.

It seems that the value change event cannot be triggered using an invoke node to work on a control... Has anyone run into this and found workarounds?

Thank you

Andrew Brown

Do you use the property Value Change node or node property Value Change (follow the signs). The latter is designed so that the structures of the events are triggered.

When playing xbox live and someone turns on the laptop he loses the connection to the server and then resets modem

when im playing left 4 dead 2 versus and kids turns to the top turn of the page to play counterstrike he says: interruption of the connection to the server and then resets my modem or router

I had the Charter to come out, they ran the new line and I always have problem help me please

Hello

· What operating system do you use?

Step 1:

I suggest you to update the firmware of the router on the manufacturer's Web site and verify that it helps. For more information on how router update contact your router manufacturer's support site.

Step 2:

Try to assign the static IP address for an Xbox 360 and the laptop and check if it helps.

To assign a static IP address for your laptop:

one) click Start > Control Panel > network and Internet > network and sharing Center and click on change adapter settings.

(b) select your network adapter. (if you have more than one list) Right-click on the adapter and choose 'Properties' from the list.

(c) under "this connection uses the following items," click once on "Internet Protocol Version 4 (TCP/IPv4) to select it and then click on the button 'Properties'.

(d) click the radio button for "use the following IP address:" enter the static IP address, you want to use in the IP address box.

(e) press "Tab" when you are finished and that the "Subnet mask" value should automatically populate with the correct value.

(f) Finally, you will need to enter the IP address of your default gateway and the IP addresses of your favorite servers and auxiliary DNS.

(g) the default gateway is the IP address of your router. The DNS addresses are usually provided to you by your ISP.

(h) click on 'OK' to save your changes, and then click 'OK' again on the local area network connection properties window. You have now assigned to your computer a static IP address in Windows

To assign a static IP for Xbox:

(a) turn on the console and press "Guide" on the controller to bring up the quick menu.

(b) go to the 'Settings' tab, then open "System Settings." The dashboard opens and the 'System settings' menu.

(c) select 'Network settings' in the menu new. Another list of menu options is displayed. Choose "Configure network." This opens the network configuration menu, where you can set a static IP address. Note your IP address, subnet mask and gateway.

(d) change your settings 'IP' to 'Manual' instead of 'automatic '. This will allow you to manually select your IP address and other settings. It can also erase your current settings, that's why you need to write.

(e) change the last three digits of the IP address. Enter the same numbers for the subnet mask and the gateway that you saved in step 3. Press 'B' to exit from the menu and save the changes

Struggling with how to properly develop this display of data of the host/VI

Hello! I hope that someone can send me in the right direction on this. I mocked upward a Panel before the way I intend it to look - a blade of filling, overlapping a waveform graph, to give the effect of a visible present value and a trace of the short story. The idea is of a large number of these kinds of indicators on a display for a bench trial-computing engine allows both simple visualization of a lot of data, and I am replacing an old system for the acquisition of data with a similar screen.

My question is how to take these indicators (which work roughly as I want) and duplicate the code 30 times without making a huge mess. I looked in the sub-panels, but it seemed that it was also a complicated thing to do thirty times. Maybe it will just be messy, but I hope that there is some good/easy way to do this.

Make a custom control seemed to be an option, but I couldn't figure out how to make the custom control to contain the table of waveform and the slide filling - and then after that, how to make the colors replacing in alarm as I already have.

I ask before I spend a lot of time on this in case I have to start over!

If you think you might be able to help you, please have a look at the attached VI with six of these things already cloned and let me know your idea. I really appreciate it.

Matt

First of all, it's a UI element user very neat looking that you offer here!

To be honest, I think that the best way to solve this problem would be to create an XControl for your UI element. This is quite a complicated process if you have not created one before, but if you're looking for an XControl to create there are plenty of resources available.

If this seems a bit too involved/advanced, your idea to employ the sub-panels is probably the best solution - create a VI that shows data and however is a lot, you need view data and load the VI in the secondary. You must of course (a range of works of good secondary references for it) doing asynchronous calls and manage references VI etc..

The key is you want to create your combo chart/slide only once and then repeat if necessary - either by an XControl or a reentrant VI loaded in a secondary school.

Controls tabs flashing when Invisible

A little history: I have a tab control that contains several controls of void and this control tab is located at the top of a vision acquisition screen. While the program is running, the user can hit 'h' key to hide all the controls, so that the user can see the screen for the acquisition of any vision. I came across a bug which, in don't break my app, is really annoying. What happens is that when the user presses the 'h' key, all the controls disappear as expected (I do this by using the property node 'visible' to the tab control), but once per second the controls on the tab flash on the screen and then disappear again. Still, these are the controls inside the tab, tab no it's me. The tab it's self is invisible as expected. Has anyone else seen this before?

Just guessing here, but I've seen funny things with the tab controls, especially when working with the visibility property. I suspect that 'under the hood' LabVIEW uses the visibility property to get the tabs to work.

In your example I (notied that you write the property each iteration.) It's not too big, a method and can lead to some ineffecintcies. Also, when the objects overlap on the FP an update to any object overlaping requires all objects to cool off, so you can lose a lot of time processor that could bog down your CPU. A possible workaround, you can try is to add a loop secod with an event inside structure to capture only changes to the visible Boolean value. Another thing to try would be hitting the visible property of the objects in the tab directly. This excerpt is a reasonable example.

Information on how to execute SQL on the CUCM himself queries please

Hello all,.

I need to run a SQL on the CUCM enumerate all directory numbers, their score and their external mask values.

I came across this snippet below earlier so I have a bit of an idea of how do but iw would be great to see some other examples of sql queries.

Any help is most appreciated.

Also, is there a document somewhere to tell me how to run these queries?

Thanks in advance

Concerning

Amanda

*******************************************************************************************************************************************************************************

Currently being moderated

04/05/2011 05:18 (in response to Joshua Royle)

Re: Y at - it a way to pull a CM report showing all phones with of turn on?

Helps you try if this the CLI SQL query execution, it must list all DN with CFA allowed the VM or a DN:

run sql select dnorpattern, cfadestination, cfavoicemailenabled CallForwardDynamic c, numplan n where c.fknumplan = n.pkid and (cfadestination! = "or cfavoicemailenabled 't =')

Hi Amanda

Basically, this is standard SQL, so that he would not bad at google 'informix instructions' select and do a bit of reading to get the basics. There are millions of permutations of requests so it comes to understand the syntax and then only by applying to the database in question. The only difference when running the commands in the CLI are:

-Precede you the standard informix with "execute sql" SQL statement

-You get no help from CUCM with syntax, so you might be well advised to use something which includes SQL a bit and he colorized you type, and then paste the commands resulting in the CUCM SSH window. I use an editor called JEdit, if you create a text file and save it as a file ending with .sql, it will highlight your syntax.

-Other programs are available that make reasonable syntactic (EQ SquirrelSQL) that are designed to query the DB directly, but you can't really query directly against the DB for security reasons. You will still need to copy and paste commands.

Now... to understand the DB you will need a reference describing all the tables, etc.. Here it is:

http://www.Cisco.com/en/us/products/SW/voicesw/ps556/products_programming_reference_guides_list.html

Choose your version of CUCM and download the document 'data definition '.

Some notes on the order:

run sql: is just the CLI command which tells the shell to perform the following as SQL.

Select: the SQL command to recover data

dnorpattern, cfadestination, cfavoicemailenabled: column names to retrieve

callforwarddynamic c, numplan n: the names of the two tables and abbreviations that you want to refer to them as

where c.fknumplan = n.pkid: This tells SQL to return values in the two tables where these fields match. In the data definition, you will see notes that c.fknumplan (i.e. the column fknumplan in table callforwarddynamic, as indicated by the prefix c.) refers to the PKID column in the area of the numplan. It is a type of join in the very standard DB CCM.

and ("cfadestination! =" or cfavoicemailenabled = "t"): another clause, fundamentally in this application that we want to see only the rows where cfadestination is not empty or cfavoicefmailenabled has the value 't' for real).

Most of the tables are related in two ways in this database:

-a column "fk" prefix refers to the field of pkid (there is always only one field per table pkid) in the table following the prefix "fk". For example above fknumplan refers to the numplan, pkid field table. fkdevice refers to the machine table, pkid field.

-a prefiex of 'traditional knowledge' column usually refers to a table enum which is preceded by 'type '. It is a table that maps the numerical value in the field of 'traditional knowledge' into a string. An example would be tkmodel - it is the type of physical phone (e.g. as 7962) and mapped as the column and a table called typemodel model 'enum' in the table.

Concerning

Aaron Harrison

Senior Engineer at Logicalis UK

Please note the useful messages...

Tunnel VPN IPSEC site 2 Site will not appear.

Hello Experts,

I was wondering if I can get help on creating an IPSEC VPN between a Cisco 2921 and ASA 550 x tunnel. Here is the config

See the race | s crypto

Crypto pki token removal timeout default 0

crypto ISAKMP policy 1

BA aes

preshared authentication

Group 2

lifetime 28800

ISAKMP crypto key address A.A.A.A xxxxxxxxxxxxxxxxxxxxxx

Crypto ipsec transform-set ESP-AES128-SHA aes - esp esp-sha-hmac

transport mode

ICQ-2-ILAND 1 ipsec-isakmp crypto map

defined by peer A.A.A.A

game of transformation-ESP-AES128-SHA

match the address iland_london_s2s_vpn

ICQ-2-ILAND crypto card

The config on the remote end has not been shared with me, so I don't know if I'm doing something wrong locally, or if the remote end is configured incorrectly.

The command Sh crypto isakmp its the following message

ISAKMP crypto to show his
IPv4 Crypto ISAKMP Security Association
DST CBC conn-State id
A.A.A.A B.B.B.B MM_NO_STATE 1231 ACTIVE (deleted)

IPv6 Crypto ISAKMP Security Association

See the session encryption
Current state of the session crypto

Interface: GigabitEthernet0/0
The session state: DOWN-NEGOTIATION
Peer: Port A.A.A.A 500
IKEv1 SA: local B.B.B.Bremote 500 A.A.A.A500 inactive
IKEv1 SA: local B.B.B.Bremote 500 A.A.A.A500 inactive
FLOW IPSEC: allowed ip 10.20.111.0/255.255.255.0 10.120.1.0/255.255.255.0
Active sAs: 0, origin: card crypto
FLOW IPSEC: allowed ip 10.10.0.0/255.255.0.0 10.120.1.0/255.255.255.0
Active sAs: 0, origin: card crypto

The command debug crypto isakmp debug logs are listed below.

ISAKMP: (0): pre-shared key local found
08:51:52.019 on 6 Dec: ISAKMP: analysis of the profiles for xauth...
08:51:52.019 on 6 Dec: ISAKMP: (0): audit ISAKMP transform 1 against the policy of priority 1
08:51:52.019 on 6 Dec: ISAKMP: AES - CBC encryption
08:51:52.019 on 6 Dec: ISAKMP: keylength 128
08:51:52.019 on 6 Dec: ISAKMP: SHA hash
08:51:52.019 on 6 Dec: ISAKMP: group by default 2
08:51:52.019 on 6 Dec: ISAKMP: pre-shared key auth
08:51:52.019 on 6 Dec: ISAKMP: type of life in seconds
08:51:52.019 on 6 Dec: ISAKMP: life (basic) of 28800
08:51:52.019 on 6 Dec: ISAKMP: (0): atts are acceptable. Next payload is 0
08:51:52.019 on 6 Dec: ISAKMP: (0): Acceptable atts: real life: 0
08:51:52.019 on 6 Dec: ISAKMP: (0): Acceptable atts:life: 0
08:51:52.019 on 6 Dec: ISAKMP: (0): base life_in_seconds:28800
08:51:52.019 on 6 Dec: ISAKMP: (0): return real life: 28800
08:51:52.019 on 6 Dec: ISAKMP: (0): timer life Started: 28800.

DEC 6 08:51:52.019: ISAKMP: (0): load useful vendor id of treatment
DEC 6 08:51:52.019: ISAKMP: (0): provider ID seems the unit/DPD but major incompatibility of 123
DEC 6 08:51:52.019: ISAKMP: (0): provider ID is NAT - T v2
DEC 6 08:51:52.019: ISAKMP: (0): load useful vendor id of treatment
DEC 6 08:51:52.019: ISAKMP: (0): IKE frag vendor processing id payload
08:51:52.019 on 6 Dec: ISAKMP: (0): IKE Fragmentation support not enabled
08:51:52.019 on 6 Dec: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
08:51:52.019 on 6 Dec: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM2

DEC 6 08:51:52.019: ISAKMP: (0): A packet is sent. A.A.A my_port 500 peer_port 500 (I) MM_SA_SETUP
08:51:52.019 on 6 Dec: ISAKMP: (0): sending a packet IPv4 IKE.
08:51:52.019 on 6 Dec: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
08:51:52.019 on 6 Dec: ISAKMP: (0): former State = new State IKE_I_MM2 = IKE_I_MM3

08:51:52.155 on 6 Dec: ISAKMP (0): packet received dport 500 sport Global 500 (I) MM_SA_SETUP A.A.A.A
08:51:52.155 on 6 Dec: ISAKMP: (0): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
08:51:52.155 on 6 Dec: ISAKMP: (0): former State = new State IKE_I_MM3 = IKE_I_MM4

DEC 6 08:51:52.155: ISAKMP: (0): processing KE payload. Message ID = 0
DEC 6 08:51:52.175: ISAKMP: (0): processing NONCE payload. Message ID = 0
08:51:52.175 on 6 Dec: ISAKMP: (0): pre-shared key found peer corresponding to A.A.A.A
DEC 6 08:51:52.175: ISAKMP: (1227): load useful vendor id of treatment
DEC 6 08:51:52.175: ISAKMP: (1227): provider ID is the unit
DEC 6 08:51:52.175: ISAKMP: (1227): load useful vendor id of treatment
DEC 6 08:51:52.175: ISAKMP: (1227): provider ID seems the unit/DPD but major incompatibility of 92
DEC 6 08:51:52.175: ISAKMP: (1227): provider ID is XAUTH
DEC 6 08:51:52.175: ISAKMP: (1227): load useful vendor id of treatment
DEC 6 08:51:52.175: ISAKMP: (1227): addressing another box of IOS!
DEC 6 08:51:52.175: ISAKMP: (1227): load useful vendor id of treatment
08:51:52.175 on 6 Dec: ISAKMP: (1227): vendor ID seems the unit/DPD but hash mismatch
08:51:52.175 on 6 Dec: ISAKMP: receives the payload type 20
08:51:52.175 on 6 Dec: ISAKMP (1227): sound not hash no match - this node outside NAT
08:51:52.175 on 6 Dec: ISAKMP: receives the payload type 20
08:51:52.175 on 6 Dec: ISAKMP (1227): No. NAT found for oneself or peer
08:51:52.175 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
08:51:52.179 on 6 Dec: ISAKMP: (1227): former State = new State IKE_I_MM4 = IKE_I_MM4

08:51:52.179 on 6 Dec: ISAKMP: (1227): send initial contact
08:51:52.179 on 6 Dec: ISAKMP: (1227): ITS been pre-shared key, using id ID_IPV4_ADDR type authentication
08:51:52.179 on 6 Dec: ISAKMP (1227): payload ID
next payload: 8
type: 1
address: B.B.B.B
Protocol: 17
Port: 500
Length: 12
08:51:52.179 on 6 Dec: ISAKMP: (1227): the total payload length: 12
DEC 6 08:51:52.179: ISAKMP: (1227): A packet is sent. A.A.A my_port 500 peer_port 500 (I) MM_KEY_EXCH
08:51:52.179 on 6 Dec: ISAKMP: (1227): sending a packet IPv4 IKE.
08:51:52.179 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
08:51:52.179 on 6 Dec: ISAKMP: (1227): former State = new State IKE_I_MM4 = IKE_I_MM5

08:51:52.315 on 6 Dec: ISAKMP (1227): packet received dport 500 sport Global 500 (I) MM_KEY_EXCH A.A.A.A
DEC 6 08:51:52.315: ISAKMP: (1227): payload ID for treatment. Message ID = 0
08:51:52.315 on 6 Dec: ISAKMP (1227): payload ID
next payload: 8
type: 1
address: A.A.A.A
Protocol: 17
Port: 0
Length: 12
DEC 6 08:51:52.315: ISAKMP: (0): peer games * no * profiles
DEC 6 08:51:52.315: ISAKMP: (1227): HASH payload processing. Message ID = 0
08:51:52.315 on 6 Dec: ISAKMP: received payload type 17
DEC 6 08:51:52.315: ISAKMP: (1227): load useful vendor id of treatment
DEC 6 08:51:52.315: ISAKMP: (1227): provider ID is DPD
08:51:52.315 on 6 Dec: ISAKMP: (1227): SA authentication status:
authenticated
08:51:52.315 on 6 Dec: ISAKMP: (1227): SA has been authenticated with A.A.A.A
08:51:52.315 on 6 Dec: ISAKMP: try to insert a B.B.B.B/A.A.A.A/500/ peer and inserted 2B79E8BC successfully.
08:51:52.315 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
08:51:52.315 on 6 Dec: ISAKMP: (1227): former State = new State IKE_I_MM5 = IKE_I_MM6

08:51:52.315 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
08:51:52.315 on 6 Dec: ISAKMP: (1227): former State = new State IKE_I_MM6 = IKE_I_MM6

08:51:52.315 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
08:51:52.315 on 6 Dec: ISAKMP: (1227): former State = new State IKE_I_MM6 = IKE_P1_COMPLETE

08:51:52.315 on 6 Dec: ISAKMP: (1227): start Quick Mode Exchange, M - ID 1511581970
08:51:52.315 on 6 Dec: ISAKMP: (1227): initiator QM gets spi
DEC 6 08:51:52.315: ISAKMP: (1227): A packet is sent. A.A.A my_port 500 peer_port 500 (I) QM_IDLE
08:51:52.315 on 6 Dec: ISAKMP: (1227): sending a packet IPv4 IKE.
08:51:52.315 on 6 Dec: ISAKMP: (1227): entrance, node 1511581970 = IKE_MESG_INTERNAL, IKE_INIT_QM
08:51:52.315 on 6 Dec: ISAKMP: (1227): former State = new State IKE_QM_READY = IKE_QM_I_QM1
08:51:52.315 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
08:51:52.315 on 6 Dec: ISAKMP: (1227): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE

08:51:52.455 on 6 Dec: ISAKMP (1227): packet received dport 500 sport Global 500 (I) QM_IDLE A.A.A.A
08:51:52.455 on 6 Dec: ISAKMP: node set-1740216573 to QM_IDLE
DEC 6 08:51:52.455: ISAKMP: (1227): HASH payload processing. Message ID = 2554750723
DEC 6 08:51:52.455: ISAKMP: (1227): treatment protocol NOTIFIER PROPOSAL_NOT_CHOSEN 3
0, message ID SPI = 2554750723, a = 0x2B78D574
08:51:52.455 on 6 Dec: ISAKMP: (1227): node-1740216573 error suppression FALSE reason 'informational (en) State 1.
08:51:52.455 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
08:51:52.455 on 6 Dec: ISAKMP: (1227): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE

08:51:52.455 on 6 Dec: ISAKMP (1227): packet received dport 500 sport Global 500 (I) QM_IDLE A.A.A.A
08:51:52.455 on 6 Dec: ISAKMP: node set 1297146574 to QM_IDLE
DEC 6 08:51:52.455: ISAKMP: (1227): HASH payload processing. Message ID = 1297146574
DEC 6 08:51:52.455: ISAKMP: (1227): treatment of payload to DELETE. Message ID = 1297146574
08:51:52.455 on 6 Dec: ISAKMP: (1227): peer does not paranoid KeepAlive.

08:51:52.455 on 6 Dec: ISAKMP: (1227): removal of HIS State "No reason" why (I) QM_IDLE (post A.A.A.A)
08:51:52.455 on 6 Dec: ISAKMP: (1227): error suppression node 1297146574 FALSE reason 'informational (en) State 1.
08:51:52.455 on 6 Dec: ISAKMP: node set-1178304129 to QM_IDLE
DEC 6 08:51:52.455: ISAKMP: (1227): A packet is sent. A.A.A my_port 500 peer_port 500 (I) QM_IDLE
08:51:52.455 on 6 Dec: ISAKMP: (1227): sending a packet IPv4 IKE.
08:51:52.455 on 6 Dec: ISAKMP: (1227): purge the node-1178304129
08:51:52.455 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
08:51:52.455 on 6 Dec: ISAKMP: (1227): former State = new State IKE_P1_COMPLETE = IKE_DEST_SA

08:51:52.455 on 6 Dec: ISAKMP: (1227): removal of HIS State "No reason" why (I) QM_IDLE (post A.A.A.A)
08:51:52.455 on 6 Dec: ISAKMP: Unlocking counterpart struct 0x2B79E8BC for isadb_mark_sa_deleted(), count 0
08:51:52.455 on 6 Dec: ISAKMP: delete peer node by peer_reap for A.A.A.A: 2B79E8BC
08:51:52.455 on 6 Dec: ISAKMP: (1227): error suppression node 1511581970 FALSE reason 'IKE deleted.
08:51:52.455 on 6 Dec: ISAKMP: (1227): entry = IKE_MESG_FROM_PEER, IKE_MM_EXCH
08:51:52.455 on 6 Dec: ISAKMP: (1227): former State = new State IKE_DEST_SA = IKE_DEST_SA

Would appreciate any help you can provide.

Kind regards

Sidney Dsouza

The phase 2 does not complete since there is no visible SPI value. In addition, depending on your configuration Transport mode is configured for phase 2 However, debug displays the tunnel mode.

Thus, as suggested earlier to debug this further and find the root cause we need to match the configuration settings in Phase 2 with regard to the remote device.

Hope that helps.

Kind regards

Anuj

How to select and default hightlight the first line in a programmatic Table(ADF Table created based on a SortableModel) ADF.

Hi all

We use JDeveloper Studio Edition Version 12.1.3.0.0 and deployed on GlassFish Server Open Source Edition 3.1.2.2 (build 5) and connect to the SQLServer database.

We created a table ADF programming related to a SortableModel created programmatically to a bean.

We need to select and highlight the first row in the table just after making it to retrieve data based on the first line.

We tried the based on the following thread: How to call the bean support just after JSFF / page fragment loads? and a few other posts online, but it does not work very well.

W has created a hidden text in the bottom of the JSF model as follows:

< af:table varStatus = "rowStat" Summary = "table" value = "#{pageFlowScope.crudBean.dynamicTable.collectionModel} '"
Rows = "#{pageFlowScope.crudBean.dynamicTable.collectionModel.RowCount} '"
contentDelivery = 'immediate' var = 'row' rendered = 'true '.
Binding = "#{backingBeanScope.crudBackingBean.tasksTable} '"
selectionListener = "#{backingBeanScope.crudBackingBean.customListener} '"
"rowSelection ="single"id ="t1"partialTriggers =": pt_gr2 "columnStretching =" column: clmn0 ">
< af:forEach items = "#{pageFlowScope.crudBean.dynamicTable.columnNames}" var = 'name' varStatus 'vs' = > "
< af:column sortable = "true" sortProperty rowHeader = "#{name}" = "no style" headerText = "#{pageFlowScope.crudBean.dynamicTable.columnLabel [name]}" "
inlineStyle = "width: 100px;" ID = "clmn$ {vs.index}" >
< af:activeOutputText value = "#{row [name]}" id = "aot1" / >
< / af:column >
< / af:forEach >
< / af:table >
....

< af:outputText id = "hiddenOutputTextId" visible = "false" value = "#{backingBeanScope.crudBackingBean.afterPageLoad} '"
Binding="#{backingBeanScope.crudBackingBean.hiddenOutputText}"/ >
And we have added the code to the bean to support below:
public String getAfterPageLoad() {}
If (!.) {AdfFacesContext.getCurrentInstance () .isPostback ()}
selectFirstRowInTasksTable();
}
Return afterPageLoad;
}
public void selectFirstRowInTasksTable() {}
try {}
RKS RowKeySet = new RowKeySetImpl();
RowKeySet rksEmpty = new RowKeySetImpl();
Model CollectionModel = tasksTable.getValue ((CollectionModel));
ROWCOUNT int = model.getRowCount ();
If (rowcount > 0) {}
model.setRowIndex (0);
Key of the object = model.getRowKey ();
RKS. Add (Key);
tasksTable.setSelectedRowKeys (rks);
SelectionEvent selectEvent =
new SelectionEvent (tasksTable.getSelectedRowKeys (), rks, tasksTable);
selectEvent.queue ();
customListener (selectEvent); / / to retrieve data
AdfFacesContext.getCurrentInstance () .addPartialTarget (tasksTable);
}
} catch (Exception e) {}
}
}
I think that () selectEvent.queue; should work even without calling the customerListener, but it is not working in all cases.
What is the problem in my code?

Have you tried to bind property of 'selectedRowKeys' to selection configuration / bean there?

Something like:
```
public RowKeySet getSelectedRKS() {
    if (rks == null) {
        // make first record as selected
        // create RowKeySet and assign it to rks variable(where rks is variable defined in bean with some scope higher than request scope)
    }
    return rks;
}
```
Dario

How to find the Bookmarks panel is enable or disable the use of Applescript?

Hi all
In Indesign, how to find the Bookmarks panel is enable or disable the use of applescript?
Please any idea on this subject!
Thank you
John.

Hi John,.

Version CC 2015 (and I guess in earlier versions) you would use:

Tell application "Adobe InDesign CC 2015"

the visible isVisible value of "Bookmarks" Panel

tell the end

isVisible

Review of each slide in the Question area

I put the field of examination of each slide of the question, but I can't find not visible. Can I find out if I have missed something?

# The examination area is not for this purpose, and in most of the types of questions it is no longer used.

I would say the best way to do what you want is to place a shape on the Quiz slides roughly the same place as the control area is right now, but make sure that it would not be obscured by other elements of the quiz slide. Add the text of the feedback to the shape you want the learner to see when you perform the revision Quiz and the Visible output value for these objects shape on each slide quiz to be OFF. Then create a conditional Advanced Action (or conditional Shared Action) must be run on the entrance to slide for each slide of the questionnaire. This conditional action checks if the Variable system called cpInReviewMode is set to 1, and so it will SHOW the shape on the slide object, OTHERWISE it will HIDE this same shape (just in case).

Then, this should mean that if your user name click the quiz of revisions on the Quiz results slide, they will see these forms of additional feedback, but at any other time, they will be invisible.

I'm editing in the bright room of Adobe and when I change in the develop module, I get the image I want, but when I see in the library module in its final State, it changed and degraded. Why is this happening?

I'm editing in the bright room of Adobe and when I change in the develop module, I get the image I want, but when I see in the library module in its final State, it changed and degraded. Why is this happening?

The difference between the raw edition photo and editing a PSD is that the PSD has black points and white pinned to the visible pixel values, the raw photo has still "headroom" with values of pixel darker than black visible and brighter than white, so when you export the raw file , there may be details that have improved (or obscured if it was another type of image) of the perception and mapping of the Compensation of the black spot on the final color profile.

This means not PS is better or LR is lower, it is enough for you to go to a different type of image. If you don't have PS to do final Assembly, you can probably do the same thing by exporting the raw in a 16 bit ProPhotoRGB TIF file, re-import this TIF and then set it LR, possibly using the tone curve to make the pitch black dark areas.

No visible mask values?

Similar Questions

Maybe you are looking for