Output {{productHeight}} and {{productWidth}} tags for calculation?

Similar Questions

• Synchronization output analog and an entry for imaging

  Hi all

  I'm stuck in my higher studies project and really need help. I tested an imaging system, where one uses two mirrors MEMS to analyze the sample and a tube set (PMT) allows to acquire voltage signals and translate them into images of scanning laser.

  I use the same DAQ card for input and analog output. The DAQ card sends features X and Y of the MEMS mirrors so that the reason for scanning 2D starts left to right and up and down.

  Scanning rate: 131500 pixels per second.

  Size: 1170 by line, 514 ranks in total pixels.

  Thus, the mirror will scan 601 380 pixels per image, which takes approximately 4.57 seconds to complete. I almost finished this part in LABVIEW.

  However, only a part of the scanned pixels are read by the PMT. We want to get an image of 512 x 512 pixels. For example, the PMT works like this:

  (1) the sampling rate is also 131500.

  (2) skip the first row.

  (3) starting at the second row, the PMT will jump the first 329 pixels, read in the next 512 pixels and skip the rest 329 pixels again. Then, it moves to the next line.

  (4) jump the last row.

  My approach in the plate sequence

  (1) ignore the signals of all 841 (1170-329 = 841).

  (2) create a loop for, run 512 times.

  (3) in each loop, first jumping 658 signals (329 x 2), then read the signals then 512 MB.

  (4) wait 1499 pixels left to complete the digitization (1170 + 329).

  Problem

  The mirror and PMT must start and finish at the same time running. However, when I run my VI for the analog input and create the image on the Panel, it takes 5.7 seconds to complete, which means that they are not at all synchronize. It seems that there is some unexpected time in the loop for, but I don't know how to change the code to meet the requirement of calendar.

  Please see the attached VI. Any help is greatly appreciated.

  ~ Sheng

  My approach in the plate sequence

  (1) ignore the signals of all 841 (1170-329 = 841).

  (2) create a loop for, run 512 times.

  (3) in each loop, first jumping 658 signals (329 x 2), then read the signals then 512 MB.

  (4) wait 1499 pixels left to complete the digitization (1170 + 329).

  Consider this: add up all these pixels, both those you want to record and those you want to ignore.

  If I read you right, that would be:

  841 + 512 * (658 + 512) + 1499

  Regardless of this number, set up a task that many samples and record the whole bloody thing.  Let the time of equipment for you.

  Then, AFTER that data are in hand, pass by and throw the first 841 points, then for each loop, throw away 658 and keep 512... etc.

  IOW, let the MATERIAL which made the better material: precise timing.

  Let the SOFTWARE do what does best software: weird logic.

• Title and Meta tags for product display?

  I see this problem correctly?   There is no way to add descriptions of title and metatag to each product pages?   If true, this is a major flaw of SEO in British Colombia.

  I went to the module templates and regular templates and do not see a way to add specific to each product page.  This should be done by default!

  When you add the meta in the layout produced great will in the thead element.

  For example, you can use tags such as custom1 for your meta description and title of product for the title of the page.

  Fact

  BC has recently updated the Blog finally with possibility to have the right title and meta so I hope that products will get some treatment in this respect too.

• Muse produced automatically from the "canonical" tags for phone and tablet, but it does not include "www". How to fix?

  So if I have my site j - 26.com redirect to www.j-26.com then my canonical url should be: " " http://www.j-26.com/ "right? "

  Adobe Muse automatically inserts the tags for the version of phone as " " http://j-26.com/ "is there a way to fix this or should I switch my www.j-26.com redirect to j - 26.com? "

  It's a kind of confusion so I hope it made sense.

  Muse is to use what you entered the download to the FTP host domain... or export as HTML dialog boxes.

• Fixed header and anchor tags

  Warnings: I am new to this forum and use HR 2015 since the end of May. I am somewhere between beginner and intermediate with CSS and HTML, and I don't know anything about javascript or JQuery.

  I tweaked the catalogue office with multi-screen presentation homepage so that it has a fixed header and content scrolls to the top under the header. It works well and looks beautiful up by clicking on a link to an anchor, for example when using the MiniTOC to navigate through a topic. The anchoring of the charges under the heading at the top of the window of the browser instead of under the header at the top of the visible space.

  After studying the problem, I had hoped that I had found a fix to it that hashtag connects this whim is the browser window, but it did not work.

  More research and digging in HR how to configure its bookmark anchors and found out that bookmarks are configured with one

  < a name = "blabla" > < / a >

  tag for anchors instead of one

  < h1 id = "blabla" > blah di blah < / h1 >

  tag.

  According to W3 Schools, "the < a > name attribute not is not supported in HTML5. Use the id attribute instead. "It's disappointing, given that the choice of output is Multiscreen HTML5.

  Can anyone offer a solution that works with apparently outdated HR < a name = "MiniTOCBookMark1 > < /a > format?"

  Thanks in advance!

  P.S. I am posting this at the end of the day and I won't work again until the morning of August 22, 2016, so if I do not answer questions of clarification immediately, please don't think I'm ignoring you.

  I have a header no scroll, and I just added the following to my screen layout stylesheet (targeting IE only):

  a[name]                    {

  padding-top: 130px;

  }

  Adjust the value of the pixel to function.

  I had a play on Chrome, and seems the following to run it:

  {[name]

  padding-top: 130px;

  margin-top:-130px;

  Display: block;

  }

• How the page break to each Department and calculate totals for Department

  I have a stored procedure that queries our sql database and returns the name of the employee, their Department, and a few other calculations. I use CFDocument to create a table and view the results. Here's the code that does this (see below) what I have to do is find a way to create a page break after that I have show a total for each column in each Department. My questions are so
  
  1. How can I insert a page break after the end of each service
  2. just above the page break, how to calculate the totals for the Department and display them?
  
  < cfdocument format = "pdf" >
  < table width = "650" border = "1" >
  < cfoutput query = "getResults" >
  < b >
  < td > #EmpName # < table >
  < td > #Dept # < table >
  < td > #JobType # < table >
  < td > #NonBill # < table >
  < td > #NonBillMeter # < table >
  < td > #NumberFormat ((NonBillPercent*100),.00) # < table >
  < td > #Bill # < table >
  < td > #BillMeter # < table >
  < td > #NumberFormat ((BillPercent*100),.00) # < table >
  < /tr >
  < / cfoutput >
  < /table >
  < / cfdocument >

  If I remember correctly, the tag you want is cfdocumentitem. Also, you want to check the attribute of cfoutput group.

  The details are in the cfml reference manual. If you do not have one, has the internet.

• Adding namespace in the tag for each group

  I want to use the substring method in tag for each group.
  Like this: <? for-each - group: current - group (); xdofx:substr(xmlTag,3)? >, but it does not work. How to make it work?
  Thank you.

  Just use the native method of substring XSL - http://www.zvon.org/xxl/XSLTreference/Output/function_substring.html

  BEEP is sensitive when you mix native and OPE methods

  Tim

• Output graphics of two loops for

  I would like to see a graph of the output generated in both loops for.

  X: steps (i x I have two loops)

  Y: Y1 should graph the polar output

  Y2 should chart the Azimuthal output

  Probably very simple to resolve/upgrade in place.  (The output file works fine).

  Thank you

  Kevin

  Good work Kevin.

  I have some suggestions for you (I don't know what it will be eventually, because then maybe they're based):

  • If the data do not change over time, you can use a graphic instead of a graph; Whatever it is, reduce the necessary processing power by updating the two parcels only once for a full run of the outside loop (see below)
  • You have a lot of indicators that are not obviously necessary (they simply out what puts out control - off 4;) Stop 5; Polar; Azimuthal, etc.).  When you submit here, the code is more it is easy to understand and faster you get an answer (minimal document also helps understand us what all is for).
  • Use the decrement vi but don't take it off 1 (reduced the increase in code).
  • Avoid strain - explicitly cast I32 to double so that no appeal should be made to the Manager of memory running (will reduce your footprint of memory of codes).
  • Written file are intensive and bays of building CU generally allocate dynamically memory - try to avoid these as much as possible.  In your VI, you can write to the file once when all iterations are complete.  This will reduce the runtime of the VI.

  Anyway, there are a whole bunch of thoughts that you probably care to hear, but I hope they have been helpful.

  Cheers, Matt

  

• 6009 outputs digital and analog input synchronization

  Hello

  I work in a program NI 6009. I want to leds by car with outputs digital NI 6009. For example, leads first will be on until what 200 micro seconds then second led will be on up to 200 micro seconds, and then first of all led will be on up to 200 micro seconds. I'll take led with photodedector signals and connect analog output photodedector input NI 6009. I want to synchronize the outputs digital and analog input and separate the first and second led signals the analog input for NI 6009 channel. How can you do with NI 6009? Please ADV

  You can not do with the USB-6009 case. Its outputs digital are software with a maximum speed of slightly more than 100 samples per second. The outputs can produce 200 microsecond pulses and cannot be synchronized with the analog input.

  You need a device with outputs digital hardware timed or counters that can produce a pulse outputs.

  You can synchronize a bit digital output and analog input recording signal on an additional channel to HAVE. Will allow you to see the photodetector and LED the drive with the same schedule and such resolution as described by the sampling rate I. The maximum sampling frequency of AI on the USB-6009 case is 48 kHz that is shared by all channels. If you have two lights to led and photodetector two signals maximum sampling rate would be 48 kHz/4 = 6 kHz which is barely fast enough for your 200 US signals. For more than 4 channels, it won't be fast enough.

  I suggest a simple oscillator circuit building and use it to clock a flip flop. This will give you alternating signals to drive the LEDs. You can use a line to reset the flip flop to give you control without the need for high speed.

  Lynn

• How save/export library tags for external HD/motor PC? Mac?

  I scored thousands of photos (jpg) in the Gallery of photos (the feature of love).  But when I moved a file on an external hard drive (for free mobile space) all tags have been lost when the file was accesed external HD or when brought him back to the laptop.  Is it possible to save or export tags on a different hard drive, computer or external?  If this is not the case, this makes labeled a waste of time if you lose all the data every time that you move your files to a different storage devide or you upgraded computer.  The tags are readable by a Mac?  Equipped with Windows Vista. No Windows Live.

  Can you specify what kind of tags your pointing to who have not transferred in the properties pictures,

  Captions and descriptive labels should go with the pictures, if they appear in windows Explorer.

  The exceptions could be people and geo tags and face recognition.

  I'll add you should check your settings, click on the blue button and then click options, there is a setting to remove information of importing photos, and if you check the Panel tags, it also has options for the information that you publish your photos, if all the parameters are checked if not to transfer the information ,

  These two areas should have no control over them.

• Not plugged into the HDMI cable between the PC and the TV for watching movies, but it has no sound and the image.

  Original title: high speed HDMI does not.

  I plugin the HDMI cable between the PC and the TV for watching movies, but it has no sound and the image.

  Hi lisa,

  Try these steps and check the result.
  Step 1: Manage audio devices
  a. Click Start and then click Control Panel.
  b. click hardware and sound.
  c. under sound, click on manage audio devices.
  d. click on the playback device you want to output sound. Right-click in the empty space and click on see the disabled devices to see other devices.
  e. Select the device and click on set as default and then click OK.

  See http://support.Microsoft.com/kb/953500

  Step 2: Graphics output to monitor
  a. right click on the desktop, click chart options.
  b. output to monitor.

  Step 3: Adjust graphics hardware acceleration
  a. open the screen resolution by clicking the Start button, Control Panel, and then, under appearance and personalization, click on adjust the screen resolution.
  b. click Advanced settings, click the Troubleshooting tab and then click on change settings.
  Note: Some video card drivers do not allow allows you to change the settings.
  c. move the hardware acceleration slider at different levels and check the result.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• I'm trying to remove the assigned tags is no longer tophotos on the computer that I also do not want the same tag for the photo n ° 1 to appear as a tag for the following pictures.

  Also, I don't want the same tag for the photo n ° 1 to appear as a tag for the following pictures.

  I called Hewlett Packard on this problem and they told me that there is a problem with Microsoft software.  They took control of my computer remotely and were not able to remove the old labels of previous photos.

  Hello the first question,

  Thank you for visiting the Microsoft answers Site.

  The relay please if you use Windows Photo Gallery to edit tags or properties file of photos. To remove a tag to a picture using Windows Photo Gallery, Windows Photo Gallery navigation pane you can right-click the label, and then click on remove.  When a label is removed in Windows Photo Gallery navigation pane, the tag is removed from all the photos and videos that use the tag.

  You can also manually add a Tag or change file properties for a picture using Windows Photo Gallery.

  For more information on the use of tags and Windows Photo Gallery, you can view the link below:

  http://Windows.Microsoft.com/en-us/Windows-Vista/tag-pictures-so-theyre-easier-to-find

  You can also see the answer to your earlier post below:

  http://social.answers.Microsoft.com/forums/en-us/vistafiles/thread/62ba1ee0-44eb-4713-B625-6273c213b1b0/

  Thank you

  Mary
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Not supported. of static vNIC to the Palo and Vic CNAs for ESX 5

  Hello

  I looked everywere see that clearly described. Most of the sources list only the no. dynamic vNIC taken in charge. Then I found a document describing the no. adapters for static and dynamic types for some operating systems and ESX 4. But not ESX 5. Someone at - it a CISCO document describing this? I think documentation is vey vague about that.

  If no doc, tdll just me, please... M81kr and CIV

  The calculation as Abi said is based on the number of uplinks recognized.

  The calculation is [15 * (number of links recognized IOM)]-2.

  1 uplink [15 * 1] = - 2 = 13 vNIC/vHBAs

  Uplink 2 = 15 * 2] - 2 = 28 vNIC/vHBAs

  4 uplink = [15 * 4] - 2 = 56 vNIC/vHBAs

  Source: http://www.cisco.com/en/US/docs/unified_computing/ucs/sw/configuration_limits/2.0/b_UCS_Configuration_Limits_2_0.html

  Kind regards

  Robert

• I accidentally uninstalled my audio output device, and now can't hear the audio.

  I acidently uninstalled my audio output device and now can not hear any audio... How can I find out how to go back and install again?

  Original title: Audio issues please help fast!

  Hello

  Going either on your computer or sound card (if you have installed a sound card) manufacturer's Web site > get a drivers and software download Section > put in your computer or sound card model number and operating system > Search Audio, etc drivers for it > download and install.

  Or do a system restore to before the problem of Audio that's happened:

  http://Windows.Microsoft.com/en-us/Windows7/products/features/system-restore

  See you soon.

• I have 3 radio button options to choose, but I want only a certain one for calculating sales tax. How can I assign a calculation to an option button?

  I have 3 radio button options to choose, but I want only a certain one for calculating sales tax. How can I assign a calculation to an option button?

  Ok. Let's say the name of the radio button group is "Radio1", the value of exports in this field is '3', the name of the subtotal is "Subtotal" and tax rate is 16%. You can use this code as the custom calculation of the tax field script:

  Event.Value = (this.getField("Radio1").valueAsString == "3")? Number (this.getField("Subtotal").valueAsString) * 0.16: 0;