'Page' does not name a type with the given Code problem

Hello

I try the code on this page , but I'm getting 'Page' does not designate a type in the Test.hpp file with the following line

private:

Page * appPage;

Container * mRootContainer;

};

What could be the solution for this problem?

OK I solved this problem with the addition of bb::cascades with the page
Please take a look at the following code

private:

BB::Cascades:page * appPage;

BB::Cascades:container * mRootContainer;

};

Tags: BlackBerry Developers

Similar Questions

computer does not boot, blue screen with the message: Stop: 0 x 00000024 (0 x 00190203, 0 X 86949258, 0xC0000102, 0x00000000)

computer does not boot, blue screen with the message: Stop: 0 x 00000024 (0 x 00190203, 0 X 86949258, 0xC0000102, 0x00000000)

Hello

1 how long have you been faced with this problem?
2. don't you make changes on the computer before this problem?

Start the computer by using the Microsoft Windows XP recovery console, and then perform a check disk on the file system.

To do this, follow these steps:

1. Insert the Windows XP CD in the CD-ROM or DVD - ROM drive, and then restart the computer. Select the required options to start the computer from the CD-ROM or DVD - ROM drive if you are prompted to do so.
2. once the Welcome to Setup screen appears, press R to start the Recovery Console.
3. If your computer is configured to dual-boot or multiple boot, select the appropriate installation of Windows XP.
4. When you are prompted to do so, type the administrator password and press ENTER. NOTE: In Windows XP Home Edition, the administrator password is blank by default.
5. at the command prompt, type the following command and press ENTER: cd system32
6. type the following command and press ENTER: chkdsk /r /p
7. remove the Windows XP CD in the disc drive.
8. Type exit to restart your computer.

Important: Running chkdsk on the drive if bad sectors are found on the disk hard when chkdsk attempts to repair this area if all available on which data may be lost

Update KB937287 keep apearing as the only updated, try install many times, but does not work, tried it with the standalone version and it keeps apearing

Update KB937287 keep apearing that the only update, tried to install a lot of times, but does not work, tried it with the standalone version and it keeps apearing, when I install it does not display an error message, just say that again was successful but when I try to look for more updated it apears again.

Hi mayortom,

Thank you for visiting the Microsoft answers Forum.

You can follow the steps outlined in the article below:

Troubleshooting Windows Update or Microsoft Update when you are repeatedly offered an update
http://support.Microsoft.com/kb/910339/

I hope that helps!

Thank you and best regards,
Abdelouahab Microsoft responds to the technical support engineer

QString does not name a type?

Hello

I'm pretty new to stunts and I do an application that needs to parse an RSS feed. I made a new class called "NGXmlParser". In this category, I have a member public parse(), which will retrieve the url of the image as a QString:

QString parse (const QVariant point) {}
ItemData QVariantMap = item.toMap ();

If (itemData.contains ("content media :")) {}
QVariantMap itemMediaMap;

If (itemData ["media: content"] .canConvert(()) {}
QVariantList itemMediaList = itemData ["media:content"].toList(); "]

If (itemMediaList.size () > 0) {}
itemMediaMap = itemMediaList.at (1) .toMap ();
} else {}
itemMediaMap = itemMediaList.at (0) .toMap ();
}

} ElseIf (itemData ["media: content"] .canConvert(()) {}
itemMediaMap = itemData ["media:content"].toMap(); "]

} else {}
qDebug()< "could="" not="" convert="" "=""><>
}
If (itemMediaMap.contains ('url')) {}
Return itemMediaMap ['url'] m:System.NET.SocketAddress.ToString ();
}
}
Return ' ';
}

I received one of the Cascades examples. I get the error message 'QString' does not designate a type. What's not? Should I do this another way?

Thank you

Ben

Try adding:
```
#include 
```

Windows Update page does not load, another updater with "update" in the url does not work, and the microsoft Download Center will not download. Help!

Right. I read the other posts and do not know if it's the same or not, but...

Update Windows page fails to load - no error message
antivirus and another updater with update in the URL cannot purely and simply, or don't load - no error message
any attempt to download anything from microsoft download site fails to load - no error message

I got stardock, not my colors, uninstalled

same result.

any ideas?

CLM-NSWG4,
It seems to me that you can have to deal with a virus\malware infection. You can watch these threads discuss virus problems and see if you are able to detect problems, that I suggest you use an online scanner (if you are able to) and scan your system.

Windows Live OneCare Safety Scanner Windows 7\Vista

Windows Live OneCare Safety Scanner Windows XP

Get rid of malware

Can I clean an already infected computer?

If you need more help then read: what to post in the Windows Update forum
Mike - Engineer Support Microsoft Answers
Visit our Microsoft answers feedback Forum and let us know what you think.

IPsec VPN Phase 2 does not. Need help with the debug output

Is someone can you please tell me why I can't establish ipsec Phase 2 negotiations. I'm trying to connect a 2651XM to a Pix 501.

Here are the isakmp debug and release of ipsec and configs. I checked the keys are the same. And sets of transformations look ok. No idea why its not working?

What is the bottom tell me?

===========================================================

01:32:37: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2

01:32:37: ISAKMP:(0:2:SW:1): IPSec policy invalidated proposal

01:32:37: ISAKMP:(0:2:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)

Mote 1.1.1.3)

01:32:37: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2

01:32:37: ISAKMP:(0:2:SW:1): IPSec policy invalidated proposal

01:32:37: ISAKMP:(0:2:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)

Mote 1.1.1.3)

===============================================================================

ISAKMP (0): start Quick Mode Exchange, M - ID - 1154286426:bb32fca6
crypto_isakmp_process_block: CBC 1.1.1.2 1.1.1.3 dest
ISAKMP (0): processing NOTIFY payload Protocol 14 2
SPI 2224366689, message ID = 1503891776
ISAKMP (0): removal of spi 1629787524 message ID = 3140680870
to return to the State is IKMP_NO_ERR_NO_TRANS
pixfirewall #.
pixfirewall # sh crypto is
ISAKMP (0): start Quick Mode Exchange, M - ID 400184159:17da535f
crypto_isakmp_process_block: CBC 1.1.1.2 1.1.1.3 dest
ISAKMP (0): processing NOTIFY payload Protocol 14 2
SPI 2649583861, message ID = 1778335964 a.
ISAKMP (0): removal of spi 4117818781 message ID = 400184159
status code returned is IKMP_NO_ERR_NO_TRANSkmp its
Total: 1
Embryonic: 0
Src DST in the meantime created State
1.1.1.2 1.1.1.3 QM_IDLE 0 0
pixfirewall #.
ISAKMP (0): start Quick Mode Exchange, M - ID 923039456:370476e0
crypto_isakmp_process_block: CBC 1.1.1.2 1.1.1.3 dest
ISAKMP (0): processing NOTIFY payload Protocol 14 2
SPI 2163779852, message ID = 2746774364
ISAKMP (0): removal of spi 212465792 message ID = 923039456
to return to the State is IKMP_NO_ERR_NO_TRANSexi

Closure of session

CCC cryp #sh
CCC #sh crypto isakmp his
status of DST CBC State conn-id slot
1.1.1.2 1.1.1.3 QM_IDLE 1 0 ACTIVE

CCC #ping 192.168.1.1

Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.1, time-out is 2 seconds:
.....
Success rate is 0% (0/5)

CCC #ping 192.168.1.5

Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.5, time-out is 2 seconds:
.....
Success rate is 0% (0/5)
CCC #debug isakmp crypto
Crypto ISAKMP debug is on
CCC #debug crypto ipsec
Crypto IPSEC debugging is on
Crypto CCC talkative #debug
detailed debug output debug is on
CCC #ping 192.168.1.5

Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.5, time-out is 2 seconds:
.....
Success rate is 0% (0/5)
CCC #.
00:51:24: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:51:24: ISAKMP: node set 1268073006 to QM_IDLE
00:51:24: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 1268073006
00:51:24: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID = 1268073006
00:51:24: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:24: ISAKMP: turn 1, AH_SHA
00:51:24: ISAKMP: attributes of transformation:
00:51:24: ISAKMP: program is 1 (Tunnel)
00:51:24: ISAKMP: type of life in seconds
00:51:24: ISAKMP: life of HIS (basic) of 28800
00:51:24: ISAKMP: type of life in kilobytes
00:51:24: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:24: ISAKMP: authenticator is HMAC-SHA
00:51:24: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:24: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:24: ISAKMP: turn 1, ESP_3DES
00:51:24: ISAKMP: attributes of transformation:
00:51:24: ISAKMP: program is 1 (Tunnel)
00:51:24: ISAKMP: type of life in seconds
00:51:24: ISAKMP: life of HIS (basic) of 28800
00:51:24: ISAKMP: type of life in kilobytes
00:51:24: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:24: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:24: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:24: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:24: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:51:24: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:51:24: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:51:24: ISAKMP: node set-429221146 to QM_IDLE
00:51:24: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-429221146
00:51:24: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:51:24: ISAKMP: (0:1:SW:1): purge the node-429221146
00:51:24: ISAKMP: (0:1:SW:1): node 1268073006 REAL reason «QM rejec» error suppression
Ted. "
00:51:24: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node 1268073006: status = IKE_QM_READY
00:51:24: ISAKMP: (0:1:SW:1): entrance, node 1268073006 = IKE_MESG_FROM_PEER, IKE_QM_
EXCH
00:51:24: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:51:24: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode has failed with the counterpart
with 1.1.1.3
00:51:54: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:51:54: ISAKMP: node set-500877443 to QM_IDLE
00:51:54: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID =-500877443
00:51:54: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID =-500877443
00:51:54: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:54: ISAKMP: turn 1, AH_SHA
00:51:54: ISAKMP: attributes of transformation:
00:51:54: ISAKMP: program is 1 (Tunnel)
00:51:54: ISAKMP: type of life in seconds
00:51:54: ISAKMP: life of HIS (basic) of 28800
00:51:54: ISAKMP: type of life in kilobytes
00:51:54: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:54: ISAKMP: authenticator is HMAC-SHA
00:51:54: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:54: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:51:54: ISAKMP: turn 1, ESP_3DES
00:51:54: ISAKMP: attributes of transformation:
00:51:54: ISAKMP: program is 1 (Tunnel)
00:51:54: ISAKMP: type of life in seconds
00:51:54: ISAKMP: life of HIS (basic) of 28800
00:51:54: ISAKMP: type of life in kilobytes
00:51:54: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:51:54: ISAKMP: (0:1:SW:1): atts are acceptable.
00:51:54: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:54: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:51:54: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:51:54: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:51:54: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:51:54: ISAKMP: node set-701693099 to QM_IDLE
00:51:54: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-701693099
00:51:54: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:51:54: ISAKMP: (0:1:SW:1): purge the node-701693099
00:51:54: ISAKMP: (0:1:SW:1): node-500877443 error suppression REAL reason "QM rejec.
Ted. "
00:51:54: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node-500877443: State = IKE_QM_READY
00:51:54: ISAKMP: (0:1:SW:1): entrance, node-500877443 = IKE_MESG_FROM_PEER, IKE_QM_
EXCH
00:51:54: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:52:14: ISAKMP: (0:1:SW:1): purge the node 1268073006
CCC #sh crypto isakmp his
status of DST CBC State conn-id slot
1.1.1.2 1.1.1.3 QM_IDLE 1 0 ACTIVE

CCC #ping 192.168.1.5

Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 192.168.1.5, time-out is 2 seconds:

00:52:44: ISAKMP: (0:1:SW:1): purge node-500877443...
00:52:50: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:52:50: ISAKMP: node set 1186613650 to QM_IDLE
00:52:50: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 1186613650
00:52:50: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID = 1186613650
00:52:50: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:52:50: ISAKMP: turn 1, AH_SHA
00:52:50: ISAKMP: attributes of transformation:
00:52:50: ISAKMP: program is 1 (Tunnel)
00:52:50: ISAKMP: type of life in seconds
00:52:50: ISAKMP: life of HIS (basic) of 28800
00:52:50: ISAKMP: type of life in kilobytes
00:52:50: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:52:50: ISAKMP: authenticator is HMAC-SHA
00:52:50: ISAKMP: (0:1:SW:1): atts are acceptable.
00:52:50: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:52:50: ISAKMP: turn 1, ESP_3DES
00:52:50: ISAKMP: attributes of transformation:
00:52:50: ISAKMP: program is 1 (Tunnel)
00:52:50: ISAKMP: type of life in seconds
00:52:50: ISAKMP: life of HIS (basic) of 28800
00:52:50: ISAKMP: type of life in kilobytes
00:52:50: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:52:50: ISAKMP: (0:1:SW:1): atts are acceptable.
00:52:50: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:52:50: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.1.68.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:52:50: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:52:50: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:52:50: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:52:50: ISAKMP: node set-1113601414 to QM_IDLE
00:52:50: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-1113601414
00:52:50: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:52:50: ISAKMP: (0:1:SW:1): purge the node-1113601414
00:52:50: ISAKMP: (0:1:SW:1): node 1186613650 REAL reason «QM rejec» error suppression
Ted. "
00:52:50: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node 1186613650: status = IKE_QM_READY
00:52:50: ISAKMP: (0:1:SW:1): entrance, node 1186613650 = IKE_MESG_FROM_PEER, IKE_QM_
EXCH
00:52:50: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:52:50: % CRYPTO-6-IKMP_MODE_FAILURE: fast processing mode has failed with the counterpart
with 1.1.1.3.
Success rate is 0% (0/5)
CCC #.
00:53:20: ISAKMP (0:134217729): received packet of 1.1.1.3 dport 500 sport 500
Global (R) QM_IDLE
00:53:20: ISAKMP: node set 459446741 to QM_IDLE
00:53:20: ISAKMP:(0:1:SW:1): HASH payload processing. Message ID = 459446741
00:53:20: ISAKMP:(0:1:SW:1): treatment ITS payload. Message ID = 459446741
00:53:20: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:53:20: ISAKMP: turn 1, AH_SHA
00:53:20: ISAKMP: attributes of transformation:
00:53:20: ISAKMP: program is 1 (Tunnel)
00:53:20: ISAKMP: type of life in seconds
00:53:20: ISAKMP: life of HIS (basic) of 28800
00:53:20: ISAKMP: type of life in kilobytes
00:53:20: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:53:20: ISAKMP: authenticator is HMAC-SHA
00:53:20: ISAKMP: (0:1:SW:1): atts are acceptable.
00:53:20: ISAKMP: (0:1:SW:1): proposal of IPSec checking 1
00:53:20: ISAKMP: turn 1, ESP_3DES
00:53:20: ISAKMP: attributes of transformation:
00:53:20: ISAKMP: program is 1 (Tunnel)
00:53:20: ISAKMP: type of life in seconds
00:53:20: ISAKMP: life of HIS (basic) of 28800
00:53:20: ISAKMP: type of life in kilobytes
00:53:20: ISAKMP: service life of SA (IPV) 0x0 0 x 46 0 50 x 0 x 0
00:53:20: ISAKMP: (0:1:SW:1): atts are acceptable.
00:53:20: IPSEC (validate_proposal_request): part #1 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = AH, transform = ah-sha-hmac (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:53:20: IPSEC (validate_proposal_request): part #2 of the proposal
(Eng. msg key.) Local INCOMING = 1.1.1.2, distance = 1.1.1.3.
local_proxy = 10.10.10.0/255.255.255.0/0/0 (type = 4),
remote_proxy = 192.168.1.0/255.255.255.0/0/0 (type = 4),
Protocol = ESP, transform = esp-3des (Tunnel),
lifedur = 0 and 0kb in
SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 2
00:53:20: IPSEC (validate_transform_proposal): invalid local address 1.1.1.2
00:53:20: ISAKMP:(0:1:SW:1): IPSec policy invalidated proposal
00:53:20: ISAKMP:(0:1:SW:1): politics of ITS phase 2 is not acceptable! (local 1.1.1.2 re)
Mote 1.1.1.3)
00:53:20: ISAKMP: node set-1692074376 to QM_IDLE
00:53:20: ISAKMP: (0:1:SW:1): Protocol to send NOTIFIER PROPOSAL_NOT_CHOSEN 2
SPI 2237255312, message ID =-1692074376
00:53:20: ISAKMP:(0:1:SW:1): sending package to 1.1.1.3 my_port 500 peer_port 500
(R) QM_IDLE
00:53:20: ISAKMP: (0:1:SW:1): purge the node-1692074376
00:53:20: ISAKMP: (0:1:SW:1): REAL reason for node deletion 459446741 error "reject QM.
Ed ".
00:53:20: ISAKMP (0:134217729): unknown IKE_MESG_FROM_PEER, IKE_QM_EXCH entry:
node 459446741: status = IKE_QM_READY
00:53:20: ISAKMP: (0:1:SW:1): entrance, node 459446741 = IKE_MESG_FROM_PEER, IKE_QM_E
XCH
00:53:20: ISAKMP: (0:1:SW:1): former State = new State IKE_QM_READY = IKE_QM_READY
00:53:40: ISAKMP: (0:1:SW:1): purge the node 1186613650
00:53:42: % LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, chang
State of Ed down
00:54:10: ISAKMP: (0:1:SW:1): purge the node 459446741

===============================================================================

6.2 (2) version PIX

ethernet0 nameif outside security0

nameif ethernet1 inside the security100

activate 8Ry2YjIyt7RRXU24 encrypted password

2KFQnbNIdI.2KYOU encrypted passwd

pixfirewall hostname

domain ciscopix.com

fixup protocol ftp 21

fixup protocol http 80

fixup protocol h323 h225 1720

fixup protocol h323 ras 1718-1719

fixup protocol they 389

fixup protocol rsh 514

fixup protocol rtsp 554

fixup protocol smtp 25

fixup protocol sqlnet 1521

fixup protocol sip 5060

fixup protocol 2000 skinny

names of

permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 10.10.10.0

255.255.255.0

permit 192.168.1.0 ip access list inside_outbound_nat0_acl 255.255.255.0 10.10.1

255.255.255.0 0.0

pager lines 24

interface ethernet0 10baset

interface ethernet1 10full

Outside 1500 MTU

Within 1500 MTU

1.1.1.3 outside IP address 255.255.255.0

IP address inside 192.168.1.1 255.255.255.0

alarm action IP verification of information

alarm action attack IP audit

location of PDM 10.10.10.0 255.255.255.0 inside

location of PDM 10.10.10.0 255.255.255.0 outside

PDM logging 100 information

history of PDM activate

ARP timeout 14400

Global 1 interface (outside)

NAT (inside) 0-list of access inside_outbound_nat0_acl

NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

Route outside 0.0.0.0 0.0.0.0 1.1.1.2 1

Timeout xlate 0:05:00

Timeout conn 0 half-closed 01:00:10: 00 udp 0:02:00 CPP 0: h323 from 10:00 0:05:00 TR

p 0:30:00 sip_media 0:02:00

Timeout, uauth 0:05:00 absolute

GANYMEDE + Protocol Ganymede + AAA-server

RADIUS Protocol RADIUS AAA server

AAA-server local LOCAL Protocol

Enable http server

http 192.168.1.0 255.255.255.0 inside

No snmp server location

No snmp Server contact

SNMP-Server Community public

No trap to activate snmp Server

enable floodguard

Permitted connection ipsec sysopt

No sysopt route dnat

Crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des

outside_map 20 ipsec-isakmp crypto map

card crypto outside_map 20 match address outside_cryptomap_20

card crypto outside_map 20 peers set 1.1.1.2

card crypto outside_map 20 game of transformation-Petaluma_VPN

outside_map interface card crypto outside

ISAKMP allows outside

ISAKMP key * 1.1.1.2 address netmask 255.255.255.255 No.-xauth No.-config-m

Ode

part of pre authentication ISAKMP policy 20

ISAKMP policy 20 3des encryption

ISAKMP policy 20 md5 hash

20 2 ISAKMP policy group

ISAKMP duration strategy of life 20 86400

Telnet timeout 5

SSH timeout 5

dhcpd address 192.168.1.5 - 192.168.1.33 inside

dhcpd lease 3600

dhcpd ping_timeout 750

dhcpd outside auto_config

dhcpd allow inside

Terminal width 80

Cryptochecksum:8c0d4948407071d3515f1546cf8bc147

: end

pixfirewall #.

=========================================================================

CCC #sh run
Building configuration...

Current configuration: 1328 bytes
!
version 12.4
horodateurs service debug uptime
Log service timestamps uptime
no password encryption service
!
CCC host name
!
boot-start-marker
start the system flash c2600-adventerprisek9 - mz.124 - 25d.bin
boot-end-marker
!
!
No aaa new-model
no location network-clock-participate 1
No network-clock-participate wic 0
IP cef
!
!
!
!

!

!

!

crypto ISAKMP policy 2

BA 3des

md5 hash

preshared authentication

Group 2

address key crypto isakmp 1.1.1.3 cisco123

!

!

Crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des

!

map Petaluma_1 1 ipsec-isakmp crypto

defined peer 1.1.1.3

game of transformation-Petaluma_VPN

match address 100

!

!

!

!

interface FastEthernet0/0

1.1.1.2 IP 255.255.255.0

automatic speed

Half duplex

!

interface Serial0/0

no ip address

Shutdown

clock speed of 56000

!

interface FastEthernet0/1

10.10.10.2 IP address 255.255.255.0

automatic duplex

automatic speed

card crypto Petaluma_1

!

IP forward-Protocol ND

IP route 192.168.1.0 255.255.255.0 1.1.1.3

!

!

no ip address of the http server

no ip http secure server

!

access-list 100 permit ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255

control plan
!
!
!
!
!
!
!
!
!
!
Line con 0
line to 0
line vty 0 4
opening of session
!
!
end

CCC #.

!
!
!
crypto ISAKMP policy 2
BA 3des
md5 hash
preshared authentication
Group 2
address key crypto isakmp 1.1.1.3 cisco123
!
!
Crypto ipsec transform-set Petaluma_VPN ah-sha-hmac esp-3des
!
map Petaluma_1 1 ipsec-isakmp crypto
defined peer 1.1.1.3
game of transformation-Petaluma_VPN
match address 100
!
!
!
!
interface FastEthernet0/0

1.1.1.2 IP 255.255.255.0
automatic speed
Half duplex
!
interface Serial0/0
no ip address
Shutdown
clock speed of 56000
!
interface FastEthernet0/1
10.10.10.2 IP address 255.255.255.0
automatic duplex
automatic speed
card crypto Petaluma_1
!
IP forward-Protocol ND
IP route 192.168.1.0 255.255.255.0 1.1.1.3
!
!
no ip address of the http server
no ip http secure server
!
access-list 100 permit ip 10.10.10.0 0.0.0.255 192.168.1.0 0.0.0.255

Hi David,

Overlooking the configuration of the router, it seems that you have applied the encryption card to the wrong interface.

interface FastEthernet0/0

1.1.1.2 IP 255.255.255.0

automatic speed

Half duplex

!

interface FastEthernet0/1

10.10.10.2 IP address 255.255.255.0

automatic duplex

automatic speed

card crypto Petaluma_1

Given that the pix will attempt to build a VPN tunnel to 1.1.1.2 map encryption Petaluma_1 must be applied to FastEthernet0/0, not FastEthernet 0/1.

Let me know if it helps.

Thank you

Loren

Save to File.vi report does not work when integrated with the executable

Hello

When I use the NI_Report.lvclass:New Report.vi and NI_Report.lvclassave report to the File.vi, I can use successfully to create and excel spreadsheet so he was working at the developer.

However when I build the source into an executable, this no longer works. (The name of the file is built from the source, so I'm not using a dialog box)

It can, however, create a .html file, but it does not seem as tidy. Why is he not creating the Excel file?

Running developer suite 2009, tried the .exe on Windows 7 and Windows XP with the same effect.

Thank you

-

James

See the attached zip file, it works for me here, see jpeg images and build the application accordingly and let us know. Did not include exe file, because the file size is too big.

Page does not develop as described in the tutorial (was: delicate design)

Hi, in this tutorial, (https://helpx.adobe.com/muse/how-to/responsive-web-design.html?set=muse--get-started--read y-to-use ) page seems to extend automatically to allow the new elements. This does not happen when I add new items. I would like to know how it works and how to make the elements relative to each other, so when the addition of this new text, how can you stop running on another text without having to manually move all the design whenever you want to make a change? Thanks Mog

Adobe muse is not exactly a modular design tool, so the answer is no, it will not automatically do what you ask, how to manage what you want, unfortunately, is at the stage of planning the Web site. Which means it's probably the best to design your Web page so you don't have to worry about overlap. Recommended for web designers is to try to use as few elements as possible. For example try using a single text field and continue to the bottom of the page using spacing of paragraphs, left/right justify etc etc. You can paste images "inline" with the text that moves with the text, see here: text on an image

This will make what I think you want, but it requires you to think differently about the design of your Web page.

I hope this makes sense? In addition, in the future, it helps a lot to take screenshots and add them to your message as a picture paints a thousand words!

Cheers, Steve.

Manage identities does not 'from' addy align with the "sent to" addy when replying

I just installed 24.6 and used the 'import' of Eudora. Everything seemed to move pretty well, but I can't understand the ' sent to '. I tried in "manage identities", does not. The problem is you answer a list of mail and thunderbird wants to insert my dominant addy instead of the address who sent the original e-mail. It is a problem when the identity must be subscribed/registered.

He does not do it every time, sometimes it inserts the correct answer "from". Cannot make sense.

Something to do with the import?

something to do with where you are in the folder hierarchy.

This account will be the default SMTP is used when the selected account is unknown, so if you have a list of e-mail account and move them e-mails in local folders to the selected SMTP server will be the value by default, where as if you are in the folder of the account the SMTp response. It goes the same for identities.

I'm pretty sure that one of these modules will meet your needs https://addons.mozilla.org/en-US/thunderbird/search/?q=identity & cat = all & appver = 24.0 & platform = windows

5.5.3 pages does not open files created with pages 5.6.1

Hello

I have a problem, one of my computers I have Pages 5.6.1. I have many files created with the most recent version of the Pages 5.6.1.

The problem is that I can not open files created with Pages 5.6.1 use another computer with Pages 5.6.1.

These files are not compatible? I get an error or anything like that, they simply do not open (nothing happens).

Thank you

This is a known issue. Update both machines to v5.6.1 Pages (providing you have Yosemite 10.10.4 or later). Unfortunately, v5.6.1 Pages can also forget open documents of his own creation.

ICB does not break breaking set with the code when executing the test test sequence point

I just started using the testbed and I use it with CVI. I am running version 4.2.1 of testbed. I'm currently trying to set up my "*.c files" of project folder appropriate to compile and run under the simple testexe of test bench and also tried the normal sequence editor. Currently, I moved all the *.c files &.h taken in charge in the same directory where the testexec.c... .not sure if it's the best place to put it?... It seems to work OK. However, I saw a few problems once the program is running. Is to show signs cited in my CVI functions but it shows as not fatal execution error: "position of unknown source, library function error, Panel, bar menu, control or a table handle is invalid" before and after pop up window panels. I tried breakpoint to the line of code in a CVI file to the project title for additional information about the error, but it seems that the breaking point is not being invoked as it does NOT run in debug in CVI mode and rather an executable. Across the service installed on the project file are *.c and not *.obj. I appreciate anyones help and give me advice. Thanks in advance

DLL is the only way to interact with code C/C++ in TestStand, Yes.

Equipment does not respond when connected with the desktop remotely

Hello

I have a PC with labview controlling a power supply via a serial connection. It works fine, except when I am looged in remote to my PC from another PC lab via desktop remotely. The VI runs correctly, but does not have the equipment to receive orders. Why would it be?

Thank you

Guillaume.

If you have configured, the remote computer might try to use the serial port on the computer you're remot desktopping of. Carefully go through the remote desktop settings and make sure that you are not telling the remote computer to use local ports.

FSX MULTIPLAYER DOES NOT HAVE MANY PEOPLE WITH THE SAME PROBLEM

I have a FSX I've always used the multiplayer mode for online flight, now a few weeks ago its been not conect, my internet is good, everything works but is not multiplayer, many people with this problem, tell us how to find a solution, we really like this multiplayer game

Hello

Thanks for posting your query in Microsoft Communities.

According to the description of the problem, it seems that you are not able to play Flight Simulator X multiplayer.

Please go ahead and read the steps mentioned from the link and later a update on the State of the question.

Microsoft Games: Multiplayer troubleshoot

You can also stay in contact with the Flight Simulator with the help of the link and check if it helps.

http://www.Microsoft.com/products/games/FSInsider/tips/pages/default.aspx

I hope this helps. Let us know if you need more assistance.

My HP printer does not seem to connect with the cartridge world ink cartridges.

My HP printer 6310v all in one does not seem to allow the use of cartridges per Cartridge World. It gives an error of cartridge indicating the cartridge must be replaced and not allow any impression at all. Help!

The reliability of the charging/reman cartridges varies considerably, but is generally low, see here for a study.

The steps described on this page can help.

I suggest you contact Cartridge World for a warranty replacement or chalk it upward to experience and get a HP cartridge.

(HP printers releases no cartridges because they are charging/reman, but they make an electric test to make sure that the cartridge is not working properly. They will reject cartrdiges that do not pass this criterion.)

My serial number does not work he begins with the letters.

My serial number does not work. It begins with the letters.
[NEVER SEND A SERIAL NUMBER IN AN OPEN FORUM.]
[personal information... [Mod - https://forums.adobe.com/docs/DOC-3731]
[This is an open forum, not the Adobe support, please do not post personal information]

This isn't a serial number to activate an Adobe product. Serial numbers for Adobe products have only numbers, 24 of them in 6 sets of 4. If you happen to find the serial number to be sure never publicly share since anyone can take and use it. Find the serial number of your product Adobe quickly

'Page' does not name a type with the given Code problem

Similar Questions

Maybe you are looking for