Pavilion dv6 6080-ep: slow start on a ssd

Similar Questions

• HP pavilion Dv6 laptop: does not start in normal mode, safe mode

  Hi all

  I have HP Pavilion DV6 laptop with windows 7 Home premium 64-bit OS. It was working fine up until two or three days.

  After that some software upgrades, it has stopped booting.   When I tried to start it in safe mode, it stops at disk.sys.

  I don't have win 7 OS CD or recovery CD.  So I downloaded the trail version of windows 7 SP1, I want to install this, but he is suspended the windows logo.  I Googled it has bitten, I loaded a linux kernel and access the hard disk.  I backed up all the files required by using this boot of linux.

  I don't know what to do now?  What is the problem with my system. When I ran the drive diagnostic. It was a failure. That means that I can't use this HARD drive?

  Any help is greatly appreciated.

  Concerning

  Stéphane

  Hi stephane,

  Well the error code certainly would indicate that the player began to fail, but just in case, you might try to wipe the entire hard drive first and then reinstalling the operating system as described below.

  Download and install Killdisk on the link below - (this application will write zeros to the entire disk).

  http://Software.LSoft.net/KillDiskSuiteFree-Setup.exe

  Download and install ImgBurn on the link below.

  http://download.CNET.com/ImgBurn/3000-2646_4-10847481.html

  Access the application of disc kill you have installed in all programs, open the main folder, then select Bootable Disk creators, then the BACK Bootable CD Creator that will burn the ISO on a blank CD bootable.

  During the following process do not worry about all warnings as your Windows 7 installation disk will reformat the HARD drive.

  Insert this CD into your PC which is unable to load the operating system properly. Close Notepad, and then start again to boot from the CD of Killdisk and follow the instructions on the screen to kill disk.

  A brief description of the process here is Killdisk.

  Use it to wipe the entire hard drive, Select (80 h) and press f10 (you will also need to type a confirmation and press enter) - ( This will make sure to include all of the partitions , and then start the process - this may take a few hours!).

  When the process is complete, remove the CD of Killdisk and try to reinstall Windows 7.

  If it still does not work, I think your only option is to replace the HARD drive.

  Kind regards

  DP - K

• HP pavilion dv6-7045ez: impossible to start SSD

  Hello, I changed my old HDD to SSD (Kingston hyperX fury 240 GB, controller SandForce® SF-2281). I tried to install windows 7, windows 10 and debian, but I still have the same problem, during installation reboot to complete, it is impossible to boot from SSD. My opinion is that the controller is not compatible with my pc (HP pavilion dv6-7045ez).

  I found crucial.com who all say the ssd compatible with series dv6-7XXX (http://www.crucial.com/usa/en/compatible-upgrade-for/HP-Compaq/pavilion-dv6-7xxx-series-%28intel-ddr...). Can I trust her?

  Thanks in advance and sorry for my bad English, it is not my native language.

  Hi @Matoran,

  Welcome to the HP Forum! Thank you for becoming a member of the HP Forum. It's a place dynamite to get help from the community, to get suggestions and find what has worked for others. Because you have the best experience, here is a link for you to see, if you have concerns: first time here? Learn how to publish and more

  I understand that you have replaced your disk by a (fury of hyperX Kingston 240 GB) SSD and are able to install Windows, but not able to boot to it later. When I checked HP Pavilion dv6 Entertainment PC Maintenance and Service of Guide, the Kingston drive is not part of the recommended replacements. That doesn't mean it won't work, only that it is not tested and the result is unknown. It may or may not work.  You can find this informative document. HP Notebook PC - Solid State Hard Drives. Please see this post by @erico Re: how to upgrade your laptop to a SATA SSD 2.5 " because it may help.

  Thank you for your participation in the Forums of HP! We want to help you as well as others who may encounter a similar problem. "Think about scoring the post that solves your problem as" ","accept as Solution " to help other members of the community! To say thanks for the help, please click "Thumbs Up icon" below.

• HP Pavilion dv6 6080 ep: update of HP Pavilion dv6 6080 ep memory

  Hello

  I own a HP Pavilion dv6 6080ep. It came with 4 GB of RAM and it has an intel processor i5. In order to do an upgrade of RAM I get Manual HP on memory full capacity. It is said that for this model, with the i5 processor it could go up to 16 GB of memory. When I searched for the spare part of HP, he said that both the 621569-001, the 4 GB and the 634091-001, for the 8 GB, should be replaced by 641369-001 and 670034-001. Let me stress to you that these replacements have slightly different form of the original. I searched among the brands of memory there, specifically Kingston and crucial that said for this model I can get 8GB in mind. I think sincerely lost now. The amount of memory can my laptop really gets and there is no record of RAM I should know about off?

  Thanks in advance,
  Paulo

  PS: I was planning on getting a tp of Kingston KVR1333D3S9 / 8G add to my original 4 GB. (for a total of 12 GB)

  This is max 16 GB of DDR3 - 1333 PC3 - 10600 SO-DIMM aka. DDR3-1600 will downclock at 1333, and that's what you're probably see. I'd get 2 identical modules and not mix and match old and more recent memory. You prefer the modules with 8 blocks of black memory on each side (low density) as the HPs like the better guy.

  This works, for example:

  http://www.Amazon.com/G-skill-204-pin-so-DIMM-laptop-F3-1600C11D-16GSL/DP/B00HHDUEDG/ref=sr_1_14?ie=UTF8&QID=1427144332&SR=8-14&keywords=DDR3-1600+so-DIMM

  Even though it says 1.35 volts it will work also to 1.5 volts if necessary. memory of 1.35 volts is a better product because they choose only the best RAM for low voltage memory chips.

  Manual

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP Pavilion dv6-6c45se: migration from hard drive to ssd

  Dear Sir / Madam
  I'm about to migration from HDD to ssd on my laptop.
  Now the question is: is my motherboard support sata 3?
  My laptop computer product name: HP Pavilion dv6-6c45se Entertainment Notebook PC

  My product number phone: A7P17EA #ABV
  I'll be glad if you help me
  Thank you

  Probably not with a 2d gen i5 processor, but it does not matter. It will support an SSD SATA-III, even if the SSD transfer is limited to SATA-II. It will always be very, very fast and you will never see no practical difference. Download the SSD, you will not be sorry. Let us know if you need help most.

• HP Pavilion X 2-n108nl: slow start with Micro SD is inserted in the drive

  Good evening
  I bought a HP X 2 10 - N108NL and noted that the start is very slow. Before the HP logo spend 30 seconds if you have inserted MicroSD card.
  This does not happen with the laptop HP X 2 10 - N011NL my friend.
  I tried to update the bios but nothing has changed.

  Giuseppe

  Hi @Giuseppe_hp71,

  Thank you for keeping me posted.

  I've exhausted my suggestions and HP support by phone being unable to overcome this problem for you, I brought your question to the attention of a team within HP. They are likely to ask for information about you in order to get your information or product serial number. Please search for a private message from a contact HP identified. Also, remember not to publicly post information and series numbers. If you are unfamiliar with the function of the private messages of the Forum works, please see this link. First time here? Learn how to publish and more

• HP Pavilion DV6-3060em will not start

  Hello! Today I buy new USB mouse (Logitech Gaming G100s) and my laptop does not start. I turn on and the screen is black. Everything is OK, when I unplung this mouse, it starts normally. Somewho can help me? Thanks, sorry for my bad English, I'm Slovenian.

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  According to the message that you posted, I suspect that this could be due to the recent changes are applicable

  Please perform the steps to solve the problem below:

  Step 01. Turn off the computer

  Step 02. Turn on the PC and keep pressing the F8 key

  Step 03. Select "Last known good configuration" in the list of the early start Option

  Note: Wait until you get to the Windows desktop

  Step 04. Please remove unwanted startup items and uninstall unwanted applications

  Step 05. Please reboot / restart your PC normally

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the star of CONGRATULATIONS on the left to say thank you *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  Although I am an employee of HP, I speak for myself and not for HP

• Pavilion dv6 3100: unable to start pavilion dv6 3100 again clone Samsung ssd 850 evo

  Im trying to upgrade the HDD to the SSD.  Tried a Samsung ssd - 850 EVO 500 GB after cloning, using Samsung data migration software.  However, Windows will not start since the new cloned ssd.  I get a black sreen showing, "windows does not have start message and all... and shows--

  File:------Boot\BCD.

  Status: 0x000000f.

  Info: an error occurred while trying to read the boot configuration data. »

  Samsung Wizard is not able to find data on the ssd.  I looked up and gathered a lot of information and did everything I could.  Disk Manager recognizes the device when connected via USB (for cloning).  Device Manager displays the storage as -«IDE...» SATA/AHCI controller... ».   I enabled AHCI in the regedit - the HKEY_LOCAL... Msahci, IastorV, etc.  I also updated all the possible drivers and firmware and BIOS (f29).  Yet once the ssd is connected and placed in the drive Bay, Windows just would not start.

  I'm an amateur, pretendng to be an "expert"!

  Someone please help!

  Ive been away for a few days.  Sorry for this late reply.

  I have treid sfc/scannow - did not work.  Not sure it'll work, I was not ready to move to another

  $50 on Acronis software cloning.  So, in the end, I opted for a clean install of windows7 operating system, using my own system recovery disks that I created previously.

  Every thing looks and works perfectly.  Samsung magician is able to detect the ssd by his real name (and not as ASMT 2115) and also shows that the AHCI is enabled. The time spent was worthwhile.

  Thank you.

• HP Pavilion P7-1254: HP Pavilion P7-1254: want to start of the SSD, but it does not work.

  Help!

  I'm trying to start the Office of an ssd.  I entered BIOS with F10 and moved by car up to the first position, but when I try to restart it won't start upward.

  I have not installed the right ssd boot from the USB port on the front of the office.

  What should I do?

  SSD is Kingston HyperX Savage 240 GB KIT

  Cloned using Acronis True Image HD software.

  Hello

  What is on the USB media?  If it's a clone of the Windows startup disk then it will not start.

• laptop Pavilion dv6 1030 ca: hard to change disk SSD drive

  Hi, I would like to know that if I can change the current HDD with a SSD of Kingston 480 GB seria ata (sata) drive, my personal opinion is that I can, but I would like a confirmation of my hypothesis. Canord

  Yes, you should be able to install and SSD drive in place of the built-in SATA HDD.

  You should be able to find compatible HARD drives in the Service guide and maintnence for your laptop on the hp.com site.

• Pavilion dv6-2010sa Notebook: RAM upgrade

  My HP Pavilion dv6 is really slow (especially when you use the internet with more than a couple of tabs open. I did a full audit of viruses, spyware, etc. - all clean. However, when I checked the system I have only 3 GB of RAM (2.75 usable).

  Increase the RAM would make a significant difference and if so what is the maximum I should buy (which would be effective)? It would also be very helpful if you can give advice if I should run extra RAM with what I already have or if I have to replace it. Finally, if you could tell me the name of the RAM should I buy and where can I buy it.

  Thanks in advance.

  Ben

  It will run up to 8 GB of RAM. This is the laptop DDR2-800 memory. This video shows the replacement of hard disk and memory so just pay attention to memory:

  https://www.YouTube.com/watch?v=koynICXjbzI

  DDR2 is very expensive. Here's the manual for your dv6:

  Manual

  Here is the Kingston showing page guaranteed compatible RAM:

  http://www.crucial.com/USA/en/compatible-upgrade-for/HP-Compaq/Pavilion-DV6-2010sa

  As you can see, 8 GB is well over $200. Personally, because I'm cheap, I would buy a single module of 2 gig and increase the total RAM of 4 GB or, to be sure it works with maximum efficiency, buy a 4 GB kit if you have 2 identical bars. A 4 GB kit is 'only' $ 56, and it is a reasonable investment. 4 concerts will be significantly better than 3. You might also think of a reinstallation of the operating system. Computers a naturally slow down with age that the registry fills up with junk. There are a few settings, you can clean up the start menu and other things less an OS reinstall.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• I have a HP laptop Pavilion dv6-2057 cl.

  It begins to start but shut down [Black's] in seconds

  What can I do?

  Hey @Kenaigma ,

  Welcome to the HP Forums!

  I understand that your Pavilion dv6 notebook will not start.

  Try to start in safe mode to check for possible problems with the graphics card drivers: start your computer in safe mode.

  You can also try a Startup Repair running tapping F11, while the laptop turns on and selecting the Startup Repair option.

  If none of these works, try load F11 and a system restore to before that the problem started.

  If you can't access the F11 recovery options and safe mode does not start, restore the BIOS. You can see a guide on this operation here: restore the BIOS.

  Here are other documents that you may find useful:

  Computer does not start and the lights blink or the computer will beep.
  Troubleshooting of the black screens with no start-up or start-up error message.
  Test of hardware failures (Windows 7, Vista).

  Let me know if it helps.

• Pavilion DV6 3000 Entertainmet: Need help to install an SSD for my laptop

  Hello everyone, I want to get a SSD for my notebook to use as first HDD and system C, so I can have a better communication and speed faster for the system (like rendering, export audio & video).
  I can do in my HP Pavilion DV6 3000 entertainment? What type of SSD can adapt to the system?
  Running on Windows 10 (recently updated), Intel i5 M520 @2.4 GHz, Ati Radeon 1 Gb HD, 4 GB DDR3 Ram... HARD DRIVE 320 GB

  I don't want to talk negatively about a manufacturer's product, but it is a fact that we saw a few compatibility issues raised here on the Forum about an old series of SSD Crucial, the MX which is not what you're asking about. I have used other than the MX series Crucial SSD successfully, but they are not my first choice. Crucial is a very reputable company and will remain fully behind their product. If they say it is compatible you aren't risking anything to try it.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• HP Pavilion dv6 - slow start compared to laptop older?

  Hello

  I recently bought a new Pavilion dv6 but noticed that there a start more slow times compared with my old Toshiba Portege R705-P35. I'm just curious as to why this is since the Portégé has much lower than my flag specs.

  Thank you

  TheLongBoarder

  Hi TheLongBoarder,

  The slow start could be caused by several different things. The first thing you want to do when diagnosed with a problem with a computer, is if it's a hardware problem or a software problem. In your case, I think it would be a hardware problem. You shouldn't have a problem with the memory or the speed of your hard drive. This model must be run at least 4 GB or 6 GB of RAM.

  It also depends what 'boot' you talk about.

  1. if it was the boot of when you press the power button to the Windows login screen (post), it could be a problem with the BIOS. May not have the most recent version, or the settings in the BIOS cannot be addressed to optimize speed and start Windows.

  If the version of the BIOS is the problem, you can find the latest version by going to the page drivers downloads HP, select the exact model of your laptop (i.e.. dv6-6c35dx) number, select your operating system and navigate to the section called "BIOS". Follow the instructions below to check if the currently installed version is newer or older version online.

  1. Click on Start and then run.

  2. In the text box on the run window, type regedit and click OK. This will open the registry editor program.

     Note: Do not make changes to any entry anywhere in the registry editor to avoid causing serious problems in the system. These steps only directly allow you to display a registry entry, is not to make changes.

  3. Find the HKEY_LOCAL_MACHINE under my computer folder and click the plus sign (+) after the folder name to expand the folder.

  4. In records resulting, find and click the plus sign (+) next to the hardware STORE to expand this folder.

  5. In records resulting, find and click on the (+) sign next to the DESCRIPTION to expand this folder.

  6. In records resulting, locate and click the folder System .

  7. In the results displayed in the right window, locate the entries SystemBiosVersion andSystemBiosDate .

  8. The data in the SystemBiosVersion field contains the version of the BIOS of your motherboard. This field can also contain additional information such as the manufacturer of the chipset and the manufacturer of the BIOS.

  9. The data in the field SystemBiosDate contains the date in the calendar associated with the current version of the BIOS of your motherboard. The date of the BIOS can be useful to determine the current version of the BIOS from the motherboard manufacturer's Web site if the version is not clear in the area of SystemBiosVersion .

  10. Close the registry editor without making any changes.

  The BIOS settings: If the problem is with the settings in the BIOS, there are a couple of tweeks that allow you to optimize speed. When you turn on the computer, the BIOS (Basic Input/Output System) works a lot of tests on devices and configure the devices connected to your computer. If some parameters are not configured correctly, the startup of your PC speed can be reduced. Enter the BIOS setup and look for commands or settings that may not be correct. To be sure, run a Google search to be sure. Make sure that your first boot device is set on your main hard drive. Make sure that the logo of the motherboard display is turned off. And make sure that the Quick start quick start feature is activated.

  2 if your talking about startup as the loading process connection Windows for a full load of Windows in the Windows desktop, you may have a problem with too many programs to load with windows. In this case, you can easily check and disable all programs unwanted on startup with Windows, which can cause speed problems. You can do this:

  1. click "Start" and type "msconfig" in the search bar and press "enter."

  2. This will open "System Configuration utility".

  3. on the right side of the window, navigate to the tab "start".

  4. you will see a list of all programs to load with Windows. Here, you can decide what you do or you want to load with Windows. Some programs are required to load with Windows so that Windows load and run properly, so careful who you disable. If you are not sure if it's necessary for Windows, you can do a quick search on google to be sure. Search for the song titled "startup item". Copy and paste in Google and type "is"EXAMPLE"necessary to start Windows? You will usually find your answer quickly enough.

  Slow start could be caused by a couple of other reasons as well.

  1.  fragmented - registry Windows registry is the most indispensable of the Windows operating system. When he begins to have problems with the registry, the speed and functionality of Windows becomes considerably slower. I doubt that this could be the problem with your computer. It is possible, but it is new and that if you have applied heavy use in a short period of time, it is not the likely culprit. If it, however, it's worth a check. You can find a good registry cleaner online and give him a check.

  2 of virus or Spyware infections- once the infections on the computer, they can cause immediate damage to Windows features. If you have been online a lot, even with an anti-virus program, you may have a virus any. You must run a full scan just to be sure. You can also download the free version of Malwarebytes and run as well. It works very well and is quite powerful.

  Hope that this helped you and you have this problem is resolved. If you have any other questions, do not hesitate to me message. In fact, I have a model dv6 that I may be able to help in any future issues, you may have.

  Later,.

  kabwebdev

• HP Pavilion dv6-3150us Entertainment Notebook not start after sitting on the side.

  Hello! I have a HP Pavilion dv6-3150us Entertainment Notebook that works under Windows 7. Last week, I traveled with him in Florida, and when I arrived and tried to turn on the laptop, it wouldn't start. The screen was white with thin lines going through it and the screen turned slowly black. I disassembled the computer and put it back together (which I have experience with, I installed a new fan at the beginning of last year) and he came in safe mode. This ihappened still once I put the laptop in my bag on back and then he pulled out a few minutes later (without even moving) and when I got home. I tested the hard drive and memory, and they both passed. Other that this question, the computer has worked fine. I need to get this problem solved, because I am a PhD student and travel frequently with your laptop. Could someone help me please? What causes this problem? Thank you.

  Hey irol72,

  Welcome to the Forums of HP Support! I understand that your HP Pavilion dv6-3150us is not initialize after being on his side, I understand your frustration and I would start you the black screen troubleshooting with no. Error Messages at startup or start-up.

  Thank you