Similar Questions

• PIX 501 problems with the web server internal.

  I want to open for my internal Web server, so it can be accessed from outside and I read about it here and how to do it and I do what I think of his right, but I can´t operate.

  Now I just tried to open the http port standard 80 but later I want to open a specific port and also use SSL on the web server for added security.

  Then I would like my setup now get help and also how to do when using other ports and SSL later.

  Thanks Thomas!

  6.3 (1) version PIX

  interface ethernet0 10baset

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  alfta hostname

  domain ciscopix.com

  names of

  name 192.168.1.16 TerminalPC

  name 192.168.3.0 Lager

  permit 192.168.1.0 ip access list inside_nat0_outbound 255.255.255.0 192.168.2.0 255.255.255.0

  permit 192.168.1.0 ip access list inside_nat0_outbound 255.255.255.0 255.255.255.0 Lager

  permit 192.168.1.0 ip access list outside_cryptomap_20 255.255.255.0 192.168.2.0 255.255.255.0

  permit 192.168.1.0 ip access list outside_cryptomap_40 255.255.255.0 255.255.255.0 Lager

  outside_cryptomap_60 ip access list allow

  192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0

  outside_access_in tcp allowed access list all eq www

  host 62.108.197.90 eq www

  IP outdoor 62.108.197.90 255.255.255.192

  IP address inside 192.168.1.254 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 62.108.197.10 255.255.255.255 outside

  location of PDM 62.108.197.11 255.255.255.255 outside

  location of PDM 192.168.1.0 255.255.255.255 inside

  location of PDM TerminalPC 255.255.255.255 inside

  location of PDM 192.168.2.0 255.255.255.0 outside

  location of PDM Lager 255.255.255.0 outside

  location of PDM 192.168.2.0 255.255.255.0 inside

  location of PDM 62.108.197.137 255.255.255.255 outside

  location of PDM 62.108.197.137 255.255.255.255 inside

  location of PDM 195.67.210.72 255.255.255.255 outside

  location of PDM 62.108.197.90 255.255.255.255 inside

  PDM logging 100 information

  Global 1 interface (outside)

  NAT (inside) 0-list of access inside_nat0_outbound

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  static (inside, outside) tcp 62.108.197.90 www TerminalPC www netmask 255.255.255.255 0 0

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 62.108.197.65 1

  Enable http server

  http 62.108.197.10 255.255.255.255 outside

  http 62.108.197.11 255.255.255.255 outside

  http 195.67.210.72 255.255.255.255 outside

  http 192.168.1.0 255.255.255.0 inside

  http 62.108.197.137 255.255.255.255 inside

  enable floodguard

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac

  Crypto ipsec transform-set esp strong - esp-sha-hmac

  outside_map 20 ipsec-isakmp crypto map

  card crypto outside_map 20 match address outside_cryptomap_20

  peer set card crypto outside_map 20 195.198.46.88

  outside_map card crypto 20 the transform-set ESP-DES-MD5 value

  outside_map 40 ipsec-isakmp crypto map

  card crypto outside_map 40 correspondence address outside_cryptomap_40

  peer set card crypto outside_map 40 62.108.197.137

  outside_map card crypto 40 the transform-set ESP-DES-MD5 value

  outside_map 60 ipsec-isakmp crypto map

  card crypto outside_map 60 match address outside_cryptomap_60

  peer set card crypto outside_map 60 195.198.46.88

  card crypto outside_map 60 the transform-set ESP-DES-MD5 value

  outside_map interface card crypto outside

  ISAKMP allows outside

  ISAKMP key * address 62.108.197.137 netmask 255.255.255.255

  ISAKMP key * address 195.198.46.88 netmask 255.255.255.255

  part of pre authentication ISAKMP policy 10

  encryption of ISAKMP policy 10

  ISAKMP policy 10 sha hash

  10 1 ISAKMP policy group

  ISAKMP life duration strategy 10 86400

  part of pre authentication ISAKMP policy 20

  encryption of ISAKMP policy 20

  ISAKMP policy 20 md5 hash

  20 2 ISAKMP policy group

  ISAKMP duration strategy of life 20 86400

  Telnet 192.168.1.0 255.255.255.255 inside

  Get out your ACL - access-list outside_access_in permit tcp any host 62.108.197.90 eq www

  And a new application:

  outside_access_in list access permit tcp any host 62.108.197.90 eq www

  Access-group outside_access_in in interface outside

  * You have the group-access above on your original configuration message, BUT not on the above post.

  Don't forget to issue clear xlate after the change and also record with write mem.

  Try to do this in the pix CLI instead of using PDM.

  Hope this helps and let me know how you go.

  Jay

• PIX with H & S VPN DMZ hosting web server to the hub

  Ok

  Heres a problem which I think would be quite common for these even remotely conscious of security. Unfortunately, my knowledge of the PIX (as well as other Cisco devices) is still in phase of 'growth '.

  So, here's the problem. I have a WAN put in place with PIXen and SonicWalls, we are set up in a design essentially Hub and Spoke (fine ok so it is partially meshed). We recently decided to pull the trigger on getting a 'real' web site and everything went relatively well that getting up and rolling. (even with my notice of 3 days/deadline), but here's the problem: I set up the web server on the DMZ to the hub pix, and I figured out (the easy part) how to set things so in the Home Office, people can connect to the web server by using the internal address, but I don't know what to do for people in remote offices with VPN home connections. I tried to define static routes, I tried to add the DMZ to the VPN trigger, I tried to do both of the last things together, and I checked that I have rules allowing traffic to the VPN outside the DMZ on the inside. So, what else can I I get?

  I have no problem by configuring a PIX for all basic ups and VPN even at this stage, I can do most of it through the CLI (even if I still want to do more through the PDM). My biggest stumbling block on the PIX has so far was when I actually involve this pesky DMZ...

  I actually two PIX in my office, two for my network domestic (one for my place in the States and one for my place in the Japan), so if you can help me, I'll be the two problems and do not forget to give a rating of excellent reviews!

  so I guess that leaves me to the place where I scream...

  Help!

  and I humbly await your comments.

  the current pix configuration should look at sth like this,

  IP access-list 101 permit

  IP access-list 110 permit

  Global 1 interface (outside)

  (Inside) NAT 0-list of access 101

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  Permitted connection ipsec sysopt

  Crypto ipsec transform-set esp-3des esp-md5-hmac superset

  myvpn 10 ipsec-isakmp crypto map

  correspondence address card crypto myvpn 10 110

  card crypto myvpn 10 set by peer

  superset of myvpn 10 transform-set card crypto

  interface myvpn card crypto outside

  ISAKMP allows outside

  ISAKMP key

   address netmask 255.255.255.255
  
  isakmp identity address
  isakmp nat-traversal 20
  isakmp policy 10 authentication pre-share
  isakmp policy 10 encryption 3des
  isakmp policy 10 hash md5
  isakmp policy 10 group 2
  isakmp policy 10 lifetime 86400
  now, to add dmz on top of the existing vpn, add the following to the pix (and apply the same concept on the remote end device)
  access-list 102 permit ip
  access-list 110 permit ip
  nat (dmz) 0 access-list 102
  

• External HTTP > internal to the web server

  Hello

  I have a router ADSL with a public IP assigned, preforming NAT. This leads to a 506th PIX which leads to a Web server. The entire interior of the ADSL is on private IP addresses.

  I want to allow external users access to the Web server on port 80.

  I inwardly and outwardly put up ICMP connectivity (for testing only) and it works correctly.

  I created a virtual server on the ADSL router that forwards port 80 traffic to the external interface of the web server. It has worked successfully for half an hour and then something in the config changed PIX and it no longer works. Here is my config PIX

  SH conf

  : Saved

  : Written by xxxxx at 08:41:10.001 NZST Thursday, October 13, 2005

  6.3 (4) version PIX

  interface ethernet0 car

  Auto interface ethernet1

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  enable the encrypted password xxxxxxxx

  xxxxxxxxx encrypted passwd

  hostname PIX

  domain ciscopix.com

  clock timezone GMT

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  icmp protocol error correction

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  no names

  name 192.168.5.3 PixExt

  name PixInt 192.168.6.1

  name 192.168.5.1 ADSLInt

  name 192.168.6.2 WebExt

  acl1 list access permit icmp any any echo response

  access-list acl1 allow icmp all once exceed

  access-list icmp permitted acl1 everything all inaccessible

  acl1 list access permit tcp any host 192.168.6.2 eq www

  pager lines 22

  opening of session

  timestamp of the record

  Record being buffered memory errors

  logging trap notifications

  ICMP allow all outside

  ICMP allow any inside

  Outside 1500 MTU

  Within 1500 MTU

  external IP 192.168.5.3 255.255.255.0

  IP address inside 192.168.6.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.6.2 255.255.255.255 inside

  PDM logging 100 information

  history of PDM activate

  ARP timeout 14400

  NAT (inside) 0 192.168.6.0 255.255.255.0 0 0

  Access-group acl1 in external interface

  Route outside 0.0.0.0 0.0.0.0 192.168.5.1 1

  Timeout xlate 0:05:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.1.0 255.255.255.0 inside

  http 192.168.6.2 255.255.255.255 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  dhcpd lease 3600

  dhcpd ping_timeout 750

  xxxxx xxxxxxx privilege 15 encrypted password username

  Terminal width 80

  Cryptochecksum:xxxx

  DMZInside (config) # route sh

  outside 0.0.0.0 0.0.0.0 192.168.5.1 1 ANOTHER static

  outside 192.168.5.0 255.255.255.0 192.168.5.3 1 static CONNECTION

  inside 192.168.6.0 255.255.255.0 192.168.6.1 1 static CONNECTION

  DMZInside (config) #.

  No idea where I have gone wrong?

  Thank you.

  you are missing this statement

  public static 192.168.6.2 (Interior, exterior) 192.168.6.2

  Thank you

  Nadeem

• Internal server messages no longer work when published on the web server, but not locally on the web server

  Just upgraded to 8 Captivate and for some reason my server any internal messages is no longer work on the web server.  I can test locally the lesson that always points to the Web server and it works.  Can't understand why when it is on the server it does not work.  The ashx handler that manages to post is fully accessible to the web server and DNS solves very well so I can't understand why he doesn't hit the Manager.  I use IIS to host it and a .ashx for managing for results.

  Is there maybe something new that needs to be allowed in IIS for 8 Captivate work?  .js seems to be fine and firewall is not the issue.  Short of ideas and the need for this work as soon as possible.

  Thank you very much for your help!

  Nick

  OK, finally solved.  For some reason any run under HTTPS lesson could not publish my results.  As soon as I changed to HTTP the results perfectly. All of this makes sense why I could post locally on the Web server.  Hope this saves someone else 5 days of hell.

• Restrict the web server integrated for listenling only on the local Interface

  I installed the CF with the built-in web server (port 8500). Now, I have to use IIS for the Web site and the web server integrated for administration of CF.
  How to configure the web server CF-Administration, it allows connection only (unrestricted firewall on port 8500) localhost?
  
  Thank you

  Try to set the following attributes in the WebService of the for the server's jrun.xml file:

  127.0.0.1
  127.0.0.1

  Ted Zimmerman

• Not possible to activate the scripts on the Web server

  Hello

  I would like to create a page .html for Web with a bit of scripting ESP included - Services because now I understand just this:

  <% for (i=0; i<3; i++) {
    ...some text...
   } %>

  According to this document NOR, I first need to enable scripting:

  To use the script with a Web service, you must enable the feature on the Web of LabVIEW server. In LabVIEW, select the script on the Web Server: Configuration page in the dialog box Options to enable the use of scripts on the Web server.

  I activated the Web server and it works OK. But there is nothing called "Scripting" in the configuration page - and the script is executed (the code is just printed in the form of simple text).

  Anyone know how to activate the ESP script?

  Version: LV 2012.

  Best regards, Jan

  Hi Jan,

  In fact, you use the ESP file instead of a static HTML file.  For example, if we had the static html file:

  Hello world

  This file can be located at something like /MyWebService/HelloWorld.html.

  If I then do something like have a page to say "Hello, Jan" or "Hello, Mark" I could use ESP.  In this case, your code might look like:

  <>

  var xname = form ['name'];

  %>

  Hello, @@xname

  The URL of such a web method is perhaps something like jan/MyWebService/Hellovar/Jan where Jan string literal passed to the terminal of a web method that can resemble

  

  In this example, the string "Jan" is passed to the terminal of the value of the VI.  What implementation of the Web method in the spec to build his signature might look like in /Hellovar /: value.

  So, back to your original question.  You embed not ESP breast and the HTML document.  Instead, you embed HTML inside a document of ESP and the rendering of the document in HTML format when accessing the URL of the Web method.  While the paper you mentioned earlier has an example project in that you can use as a reference

• How to allow the clean-up actions to be taken by a reentrant clone before he is killed, seen through the web server, through a narrow browser?

  Here's a question I'll get lucky with.  I have a VI, set to be reentrant, broadcast via the web server.  The main instance of the VI is never worked with: it's a clone whenever someone accesses the correct URL, and the user interacts with the newly created clone (never the main forum).  A clone is able to configure and calling instrument VI when good IDs are entered, which translates to browser popups that are controllable on the end of the user (even if only one user ever does both. To clarify, many clones can be opened simultaneously for connection purposes, but that a user never interacts with the instruments that are not themselves reentrant).

  If the user clicks on my Logout button in their browser, it is trivial to close these instruments other, independent and properly clean.  But if the user simply click on the red X in their browser, it is non-stop and the instruments that the clone called stay open on the server, when they close.

  My experience so far:

  No close panel? event seems to be triggered in the clone.  The clone simply cease to be.

  The remote_panel_connections property doesn't seem to work properly in this case (I have not had luck so far), since it is possible that more than a clone to be active and that the main parent who is spawning clones stays running, but is not interacted with in some way.

  What I need:

  One way for the clone of VI recognize that the user has closed his browser and communicate that it closes all the assets of VI before ending.

  --------------

  I would like to avoid forcing the instruments that the clone call to constantly query to see if the VI clone is present on the network.  If there is no other solution, but this, I would appreciate a suggestion as to the intensive way less code and resources to implement this type of interrogation, as the instruments are really designed to be totally independent after they are called, rather than under vi.

  Thanks for all comments, let me know if you need more information.

  MTdev wrote:

  One way for the clone of VI recognize that the user has closed his browser and communicate that it closes all the assets of VI before ending.

  When a VI stops running, any reference as a queue is also cancelled.  You can make use of this fact.  If your original clone VI could launch a second reentrant VI, which remains active, you could channel all communications to the instruments via VI second using a queue created in the first.  When the first VI disappears, it will trigger an error waiting waiting VI in the second (no vote office is involved).  The second VI can take all the necessary measures.

• start the Web server in different folders

  I developed a compiled VI (Smarts - Net .exe) that has been designed to operate in a specific folder (\Smarts-Net) and activated the Server Web page of Smarts - Net .html in the same folder.  So far so good.

  The application receives data in real time produced another of our programs and generates graphs to show "what happens".

  My clients would like run multiple instances of my program for their customers, but want to isolate their customer 'A' customer 'B' so that they cannot display the data on the other.  I can start my application using different IP ports so that I can have multiple views, but I want to further isolate the data of the customer in different folders.

  I did a 'manager' program that will create a subfolder of the folder in my main application (\Smarts-Net) so that it would appear as "\Smarts-Net\JobA" and copy all the files in the main folder in the new subfolder.  I then change the of Smarts - Net .ini file with the new pathname of the file and the new port like this number:

  [Smarts-Net]
  server.app.propertiesEnabled = True
  Server.OLE.Enabled = True
  Server.TCP.servic = "My Server computer/VI"
  server.vi.propertiesEnabled = True
  WebServer.DirectoryIndex = "index.htm"
  WebServer.LogEnabled = True
  WebServer.LogPath=C:\Smarts-Net\Logs\Smarts-Net.log
  WebServer.MimeTypes = (a LOT of Mime types in here... I left aside for this post)
  WebServer.Port = 9501
  WebServer.Enabled = True
  WebServer.RootPath=C:\Smarts-Net\JobA
  WebServer.TcpAccess = "" + c * ' "
  WebServer.ViAccess = "' + * '"
  DebugServerEnabled = False
  DebugServerWaitOnLaunch = False

  After you change the .ini file, I start the application (Smarts - Net .exe) to the new folder.

  This is where I need help.  If I try to display the VI from another computer using an address like http://snape:9600/JobA/Smarts-Net.html, I get an "HTTP 404 - File not found" error.  But, if I try to http://snape:9600 / Smarts - Net .html, I get the VI Panel!

  Thus, it seems that I can change the Port in the .ini file, but not the RootPath.  Does anyone know how to get the html to load from a different folder from the one specified when I created the application code?

  Hello Steve,.

  From your description it looks that the web server is already doing what you say you need for.

  There is a difference between the URL path, the path that is entered in the browser and the path of file system, the location of the file on the disk.

  The WebServer.RootPath token specifies the directory of the file system that corresponds to the root directory, "/", in the URL. You have specified C:\Smarts-Net\JobA as root your path so all files in this directory will be the URL of the http://mycomputer:myport / myFile. If you want the URL of http://mycomputer:myport/Logan/myFile then you need to have your root C:\Smarts-Net\ directory.

  Does make sense?

  Nathan

• Additional installers do I need to use the web server?

  I am building an application in LabVIEW 8.6 and want it includes the Web of LabVIEW server and eventually Web Services.  Should additional installers I include?  In addition to the runtime, the following options are: 'LV Web Services', "NI LabVIEW Run-Time Engine Web Server", "NI LabVIEW Web Server."  I can find no documentation explaining the differences between these - especially the last two.

  Hello Nathan,.

  From 8.6 web server is a separate component. Just as LabVIEW desktop is a separate installation program since the runtime if there is a web server for each component. In addition, Web Services is a component that is generated on the web server.

  So, if you need web server in the Office two, LabVIEW and RTE and you eventually will need to deploy web services, as well, then you'll need to install these components.

  Here's our FAQ to get Web services work - you might be useful.

  FAQ Web services

• Activation of scripts on the Web server

  I found this, but cannot locate Scripting on the Web Server: Configuration page

  Activation of scripts on the Web server

  To use the script with a Web service, you must enable the feature on the Web of LabVIEW server. In LabVIEW, select the script on the Web Server: Configuration page in the dialog box Options to enable the use of scripts on the Web server.

  http://zone.NI.com/DevZone/CDA/tut/p/ID/7738

  It seems that scripting is enabled automatically.

• What is the web server integrated for Windows XP Professional?

  Hello

  I would like to know what the web server integrated for Windows XP Professional.

  I don't know of a free web server like Apache or IIS.

  I want to host my site on the net using the web server integrated in XP (not IIS).

  Thanks in advance.

  It is not just any server web, other than IIS, integrated with Windows XP Professional.

  You think perhaps of Personal Web Server (PWS) which was part of the old operating systems like Windows NT.  Which no longer exists in Windows XP Professional - it has been replaced by IIS.

  -B-
  http://www.officeforlawyers.com | http://www.OneNote-tips.com
  Author: Guide to counsel for Microsoft Outlook

• run the Web server in vmware

  Hello
  I run the Web server in the os(xp pro) host and now I want to run the Web server in the guest operating system
  I put things in the host operating system, follow
  router setting page (shared ip settings page)
  1 DHCP using OFF
  2 DMZ host server using on 192.168.10.201
  3. setting of virtual server 192.168.10.201 port TCP port internal external port 81 81
  TCP/IP
  1 use the following IP 192.168.10.201
  2 gateway 192.168.10.1
  3. the DNS settings of
  4. on the Advanced tab > Internet connection sharing > VMware Network Adapter VMnet 8
  for now, when someone tries to access my WAN IP then page host server is apear (from external network)
  If I stop server Web host then cannot access my WAN IP

  and in VMware, I put the (Windows XP Pro)
  TCP/IP configuration
  1 use the following IP 192.168.88.201
  2. default gateway 192.168.88.2
  3. the DNS settings of
  4. click the guest OS tab and click Edit > virtual network editor > NAT VMnet host is VMnet8
  5. setting NAT > Port forwarding > Add >: host port 81 machine virtual ip address 192.168.88.201 port 81
  and at the moment access to 192.168.88.201 in the guest operating system is ok the page is apear
  but nothing is apear when try and access my WAN IP external network and if I start it the host Web server then the host page is apear that im is not the intention of
  How can I make the Web server of the guest to access other networks operating system?
  in the guest operating system, I can access Web server of the customer by access 192.168.10.201
  but I can't access Web server of the client by typing host operating system access the 192.168.10.201
  any ideas? My version of vmware's vmware-workstation - 6.5.2 for windows

  Hi Teayun,

  Thanks for visiting the site of the community of Microsoft Windows XP. The question you have posted is related to VMware and would be better suited to the VMware or TechNet community. Please visit the link below to find a community that will support what ask you

  http://www.VMware.com/support/
  http://TechNet.Microsoft.com/en-us/default.aspx Shawn - Support Engineer - MCP, MCDST
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think

• WANT to 114 does not connect to the Web server

  Have installed a 114 WANT, everything works except for the webservices - wireless eprint etc.

  I tried everything-

  1 re-install services - error cannot connect to the web server

  2. Update - error cannot connect to the web server

  3 give the static IP address

  4 restore the default settings

  I have an internet connection on all computers.  Can someone give me a hint on how to get Web services to work?

  Hi sbenzie,

  How your printer is currently connected to the network? Via Ethernet or wireless? What is your current router / network configuration? That shows your printer because it is the IP address? What happens when you try to launch applications?

  Not yet given the information above, here's what I would try.

  I suggest to reconnect the printer to the network by running the Wireless Setup Wizard and attempt to restart the web services. If this is not enough, you may change some DNS settings in printers EWS (built-in web server) to do this, put the IP address in a browser window on your PC.

  This should start the integrated Web server. In SAP, select the network on the network tab, select 'network '.

  Then select "network address" (IP). Do not change the IP configuration at the top. Go down under "DNS address configuration"and select 'Manual DNS server'. " Under manual DNS server, enter (an 8 in each box on the first line) 8.8.8.8 and 8.8.4.4 on the second line. Press the button 'Apply' at the bottom.

  Now try to connect to Web Services again.

• I can\ to connect to the web server integrated on my D7460?

  Hello

  I had some problems with my Photosmart D7460 printer and resolved (for now) most of them.

  Except that I can't connect to the built-in web server. Also, I do not get a response when I try and ping the printer.

  Giving to think I have problems of network with the exception that I can print to this printer... Well well, from most of the computers on the network, but that's another story.

  I checked what the said road IP address he gave to the printer.

  Any suggestions would be welcome.

  OK, I seem to have solved the problem.

  I'm not sure that bit of material, it was causing the problem but it seems to come form tries to use "WPA & WPA2" parameters (BT Home Hub 3.0) wireless access point.

  Who having spent 'WPA only' I can now ping, print and connect to the web server.