PIX 515E without NAT from upper to lower
Dear all,
Pls find attached schema and configuration PIX 102 and 105 PIX.
Network 192.168.105.x, 192.168.102.x can communicate with the outside world and from the outside we can access 192.168.102.x some open ports.
192.168.105.1is on the interface of higher security and 192.168.102.3 is on the low safety for PIX105 interface.
192.168.105.x can communicate with 192.168.102.x using NAT.
Now the question is:
192.168.105.x cannot communicate with 192.168.102.x without Tried NAT. using the special conversion rules and Nat 0 but cannot continue to communicate.
192.168.105.X is unable to connect to 192.168.101.x (road via PIX 102 and router)
192.168.101.X cannot communicate with 192.168.102.x
I don't want NAT to use between 192.168.105.x, 192.168.102.x and 192.168.101.X
Grateful if you can help do ASAP
Kind regards
Prashanth
you said "192.168.101.x need to access 192.168.102.x for object group dc."
provide that you will speak the traffic is initiated by sous-reseau.101 for sous-reseau.102, then you need to apply another State on pix102.
for example
static (intf2, inside) 192.168.101.0 192.168.101.0 netmask 255.255.255.0
clear xlate
Apart from that, I see no error with the two pix, the config of the router config.
to check the question it either relates to the data center router, try ping pix102.
First, ping the int data center router series, then ping the router the data center sous-reseau.101.
Tags: Cisco Security
Similar Questions
-
We have recently acquired a new partner that is connected by a frame relay to our DMZ.
Here's my problem. The router (frame relay) is in our DMZ their public addresses to our addresses in the DMZ to NATS
172.16.10.90 ftp port
172.16.10.4 port 9100
172.16.10.5 port 9100
172.16.10.6 port 9100
I want to take the source address and the NAT inside our network:
10.10.2.90
10.10.2.4
10.10.2.5
10.10.2.6
I don't have physical devices in the DMZ for these addresses and I have not been able pass traffic back from the demilitarized zone. I have access lists allowing traffic to DMZ 172.16.10.x inside the 10.10.2.x via the appropriate ports.
Currently, we have our Web server and a mail gateway in the demilitarized zone, I want to do this without changing the overall or to compromise the DMZ rules that are currently in place.
Thank you for your help
This feature is available in 6.3 + codes
upgrade to the latest code what 6.3.4
-
PIX 515e - can't view the site from the inside
Hi people
I have a PIX 515E with a Web server in the DMZ. Using a static control that is on the web with an internet address and can be viewed from anywhere outside of the firewall. But users inside can't display it, by ip address or domain name. Would be grateful for any help on the access for this list
Thank you
Oops...
I did not understand how you want this configuration...
It should work...
http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_tech_note09186a0080094aee.shtml#DMZ
-
I configured a PIX 515E, OS 7.0 (1) f? PAT r dynamic of the inside of the network to the external ip address of the PIX. I also configured for icmp access lists from inside to outside and inside. All traffic (www, dns, ftp, etc.) works very well except ping. Whenever I do a ping from host inside to any address outside, I get the following error messages:
6. August 24, 2006 11:10:52 | 609002: duration of disassembly-outside local host: 193.222.224.104 0:00:10
6. August 24, 2006 11:10:52 | 302021: connection of disassembly ICMP for faddr gaddr laddr 8994/FDFR001 212.203.90.59/9 193.222.224.104/0
6. August 24, 2006 11:10:50 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/8 laddr FDFR001/8993
4. August 24, 2006 11:10:50 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".
6. August 24, 2006 11:10:50 | 302020: ICMP connection built for faddr gaddr laddr 8994/FDFR001 212.203.90.59/9 193.222.224.104/0
6. August 24, 2006 11:10:48 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/7 laddr FDFR001/8992
4. August 24, 2006 11:10:48 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".
6. August 24, 2006 11:10:48 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/8 laddr FDFR001/8993
6. August 24, 2006 11:10:46 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/6 laddr FDFR001/8991
4. August 24, 2006 11:10:46 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".
6. August 24, 2006 11:10:46 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/7 laddr FDFR001/8992
6. August 24, 2006 11:10:44 | 302021: connection of disassembly ICMP for faddr 193.222.224.104/0 gaddr 212.203.90.59/5 laddr FDFR001/8990
4. August 24, 2006 11:10:44 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".
6. August 24, 2006 11:10:44 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/6 laddr FDFR001/8991
4. August 24, 2006 11:10:42 | 106023: Deny icmp src, dst outside: 193.222.224.104 inside: 212.203.90.59 (type 0, code 0) by access-group "outside_access_in".
6. August 24, 2006 11:10:42 | 302020: ICMP connection built for faddr 193.222.224.104/0 gaddr 212.203.90.59/5 laddr FDFR001/8990
6. August 24, 2006 11:10:42 | 609001: built outside local host: 193.222.224.104
What could be the problem?
Thank you, Meg
It's only to predict the responses of echo at all on the external interface. If you do the following ACL on the outside, it should work...
outside_access_in list extended access permit icmp any any echo response
-
Hello
7.0 (1) version pix
ASDM version 5.0 (1)
I have a situation where you go paas-thanks to the VPN feature goes on our PIX 515E. I tried to put this on the pix using a VPN Wizard Site to site
who is enabled. I was unable to connect to the pix from the remote site. Witch's journal replied negotiate the pix is OK and the success
The problem is when I try to set up the tunnel to the top of the remote site. I fall without failure.
where can I see the vpn pix for error log?
is there a manual for the solution of site to site VPN using the wizard
Help, please.
Thanks in advance
the section 'use adsm' (step 14) gives an example on how to set up vpn lan - lan via adsm
Newspaper to go to the section "check".
-
Hello
I have pix 515E and I configured a VPN on it. My users connect to my network from the internet via the Cisco VPN client.
I have problem, only their LAN machine can do VPN from Cisco VPN client to my network at once.
Users are connected to the internet via an ADSL router and the LAN switch.
--------------------------------------------------
PIX Config:
6.3 (4) version PIX
interface ethernet0 car
Auto interface ethernet1
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
enable encrypted password xxxxxxxxxxxxxxx
xxxxxxxxxxxxxxxx encrypted passwd
hostname ABCDEFGH
ABCD.com domain name
clock timezone IS - 5
clock to summer time EDT recurring
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
inside_out to the list of allowed access nat0_acl ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
list of allowed shared access ip 192.168.1.0 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
Outside 1500 MTU
Within 1500 MTU
IP address outside xxx.xxx.xxx.xxx 255.255.255.0
IP address inside 192.168.1.1 255.255.255.0
alarm action IP verification of information
alarm action attack IP audit
IP local pool vpnpool 192.168.2.1 - 192.168.2.254
PDM logging 100 information
history of PDM activate
ARP timeout 14400
Global interface 10 (external)
NAT (inside) 0-list of access inside_out-nat0_acl
NAT (inside) 10 0.0.0.0 0.0.0.0 0 0
Route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
AAA-server GANYMEDE + 3 max-failed-attempts
AAA-server GANYMEDE + deadtime 10
RADIUS Protocol RADIUS AAA server
AAA-server RADIUS 3 max-failed-attempts
AAA-RADIUS deadtime 10 Server
AAA-server RADIUS (inside) host ABCDE timeout 10
AAA-server local LOCAL Protocol
RADIUS protocol radius AAA-server
Radius max-failed-attempts 3 AAA-server
AAA-radius deadtime 10 Server
RADIUS protocol AAA-server partnerauth
AAA-server partnerauth max-failed-attempts 3
AAA-server deadtime 10 partnerauth
partnerauth AAA-server (host ABCDEFG myvpn1 timeout 10 Interior)
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Permitted connection ipsec sysopt
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto-map dynamic outside_dyn_map 20 the transform-set ESP-3DES-MD5 value
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
card crypto client outside_map of authentication partnerauth
outside_map interface card crypto outside
ISAKMP allows outside
ISAKMP key * address 0.0.0.0 netmask 0.0.0.0
ISAKMP identity address
part of pre authentication ISAKMP policy 8
ISAKMP strategy 8 3des encryption
ISAKMP strategy 8 md5 hash
8 2 ISAKMP policy group
ISAKMP life duration strategy 8 the 86400
part of pre authentication ISAKMP policy 10
ISAKMP policy 10 3des encryption
ISAKMP policy 10 sha hash
10 2 ISAKMP policy group
ISAKMP life duration strategy 10 86400
vpngroup myvpn address vpnpool pool
vpngroup myvpn ABCDE dns server
vpngroup myvpn by default-field ABCD.com
splitting myvpn vpngroup split tunnel
vpngroup idle 1800 myvpn-time
vpngroup myvpn password *.
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.1.200 - 192.168.1.254 inside
dhcpd dns ABCDE
dhcpd lease 3600
dhcpd ping_timeout 750
field of dhcpd ABCD.com
dhcpd outside auto_config
dhcpd allow inside
Terminal width 80
--------------------------------------------------
Thanks in advance.
-Amit
Try to add the "isakmp nat-traversal" command to your PIX. I suspect what happens is that Remote LAN users is translated to a single IP address as they pass through the DSL connection. I also assume that the machine doing the translation has a capacity of IPSec passthrough. Linksys routers would be a good example of this type of NAT device that allows IPSec pull-out.
If that's the case, that a single VPN connection will be able to operate both. The above command will turn PIX detect clients that are located behind a NAT device, and then try to configure the VPN sessions in UDP packets and so to work around the limitation of NAT and IPSec passthrough device.
-
Using PIX 515E configuration require
Dear all,
Hi.Actually I need help for PIX 515E.Pls. check out the scenario, design & suggest?
Pls. find the details following and configuration of VLAN attached router.
# I want to put as
«Spend my LAN on CISCO 2900 (range 172.16.29.X IP...» (25 PCs) - VLAN router - CISCO PIX - ISP public IP.
# Now it's
"My LAN on CISCO 2900 - VLAN (external) router - ISP.
Details of router & PIX:
#Router inside the IP - 172.16.29.1 (inside property intellectual as it is very critical that cannot be changed)
Outdoor #Router ip - what ip should I use? (I tried with 1.1.1.1 255.255.255.0)
#PIX outside intellectual property - what ip should I use? (My ISP IP?-j' tried with 208.144.230.197 which is currently outside of my router)
#PIX within the intellectual property - what ip should I use? (I tried with 1.1.1.2 255.255.255.0)
Connection ISP #My is directly from the ISP GW to an ethernet cat 5 on my router VLAN
#I would allow www, FTP, web-based like Yahoomail... etc... & Messenger services
VLAN router Config:
Current configuration: 1028 bytes
!
version 12.3
horodateurs service debug datetime msec
Log service timestamps datetime msec
no password encryption service
!
hostname VLANRouter
!
boot-start-marker
boot-end-marker
!
activate the gcsroot password
!
No aaa new-model
IP subnet zero
!
!
no record of conflict ip dhcp
DHCP excluded-address IP 172.16.29.1 172.16.29.240
DHCP excluded-address IP 172.16.29.250 172.16.29.254
!
IP dhcp pool dhcppool
network 172.16.29.0 255.255.255.0
DNS-server 208.144.230.1 208.144.230.2
router by default - 172.16.29.1
!
!
!
!
controller E1 0/0
!
controller E1 0/1
!
!
interface FastEthernet0/0
IP 208.144.230.197 255.255.255.224
NAT outside IP
automatic duplex
automatic speed
!
interface FastEthernet0/1
IP 172.16.29.1 255.255.255.0
IP nat inside
automatic duplex
automatic speed
!
IP nat inside source list 7 interface FastEthernet0/0 overload
IP http server
IP classless
IP route 0.0.0.0 0.0.0.0 208.144.230.200
!
!
access-list 7 permit 172.16.29.0 0.0.0.255
!
Line con 0
line to 0
line vty 0 4
opening of session
!
!
!
end
All advice is appreciated.
Kind regards
Hiren s Mehta.
ORG Informatics Ltd.
Bamako, MALI
AFRICA
Hi hiren,.
See the answers below:
#Router inside the IP - 172.16.29.1 (inside property intellectual as it is very critical that cannot be changed)
When you upgrade the PIX router inbetween and your switch, you must put the PIX inside IP like 172.16.29.1 and change the router within the subnet to someother pool. Do the PAT on the PIX, rather than the router.
Outdoor #Router ip - what ip should I use? (I tried with 1.1.1.1 255.255.255.0)
Router outside the property intellectual property will be that given by the ISP... The ISP would have given a public IP address for the WAN link. This cannot be changed.
#PIX outside intellectual property - what ip should I use? (My ISP IP?-j' tried with 208.144.230.197 which is currently outside of my router)
PIX outside IP must be comprehensive. ISP would have given you a LAN subnet. Use it. In this case, inside the interface of the router has an IP address from that subnet even...
#PIX within the intellectual property - what ip should I use? (I tried with 1.1.1.2 255.255.255.0)
PIX inside must be 172.16.29.1, which will be the default gateway for all PCs. If you change this subnet, then the PC should have an IP address on the same subnet that has decided.
Connection ISP #My is directly from the ISP GW to an ethernet cat 5 on my router VLAN
didn't get it... is that on the internet router or switch?
#I would allow www, FTP, web-based like Yahoomail... etc... & Messenger services
If all these must be permitted from inside to outside, you have not open anything... by default, all traffic to the inside outside is allowed (except if you put a list of access denied)...
-
PIX 515E, 7.2 (1), restarts randomly several times per day
Hello
We have a PIX 515E race 7.2 (1) that reboots randomly. It has happened 4 times this morning and has been for several days.
There is no significant syslog messages prior to the restart of the box. Monitoring CPU and memory usage shows nothing ununusual.
No failover and without VPN. Pretty basic config, a flow low traffic.
I've attached the crashinfo file - I looked through and it is meaningless to me.
Someone at - it an idea?
see you soon
Chris
The inspect esmtp is causing your ASA crashing. See: CSCse41795
HTH pls note
-
Hello
I have a PIX 515E current of execution to 7.
Is it possible to use VPN with only 1 static IP address from the ISP (no gateway or the ip address of the ISP router is provided).
I can set up routing on the ADSL modem, but then the PIX does not have a valid Internet IP address?
I think that v7 does not support PPPOE? so I can't set the mode on the bridged adsl modem?
Is there a way to fix this?
Any help appreciated gratefully.
apply the commands below:
ISAKMP identity address
ISAKMP nat-traversal 20
If the problem persists, then please post the entire config with ip hidden public.
-
I am a new user and I'm trying to configure a PIX 515e Ver 6.3 (3). How can I give my users inside access to my webfarm located on dmz1. I am able to access the test sites inside and outside dzm1. I can't access the Web inside dmz1 sites. Here is my current config:
6.3 (3) version PIX
interface ethernet0 100full
interface ethernet1 100full
interface ethernet2 100full
Automatic stop of interface ethernet3
Automatic stop of interface ethernet4
Automatic stop of interface ethernet5
ethernet0 nameif outside security0
nameif ethernet1 inside the security100
nameif ethernet2 dmz1 security50
nameif ethernet3 intf3 securite6
nameif ethernet4 intf4 security8
ethernet5 intf5 security10 nameif
enable password xxxx
passwd xxxx
hostname pix1
apprendrefacile.com domain name
fixup protocol dns-length maximum 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol 2000 skinny
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names of
aetest name 10.10.10.1
name 10.10.10.2 aetest1
name 13.13.13.3 aetestdmz
name 13.13.13.4 aetestdmz1
access-list from-out-to allow tcp any any eq www
pager lines 24
opening of session
debug logging in buffered memory
Outside 1500 MTU
Within 1500 MTU
dmz1 MTU 1500
intf3 MTU 1500
intf4 MTU 1500
intf5 MTU 1500
IP address outside the 12.x.x.x.255.255.0
IP address inside 10.10.10.2 255.255.255.0
IP address dmz1 13.x.x.x.255.255.0
No intf3 ip address
No intf4 ip address
No intf5 ip address
alarm action IP verification of information
alarm action attack IP audit
no failover
failover timeout 0:00:00
failover poll 15
No IP failover outdoors
No IP failover inside
no failover ip address dmz1
no failover ip address intf3
no failover ip address intf4
no failover ip address intf5
history of PDM activate
ARP timeout 14400
public static 12.12.12.15 (inside, outside) aetest netmask 255.255.255.255 0 0
public static 12.12.12.16 (inside, outside) aetest1 netmask 255.255.255.255 0 0
(dmz1, external) 12.12.12.17 static aetestdmz netmask 255.255.255.255 0 0
(dmz1, external) 12.12.12.18 static aetestdmz1 netmask 255.255.255.255 0 0
Access-group from-out-to external interface
Route outside 0.0.0.0 0.0.0.0 12.12.12.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225
H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00
Timeout, uauth 0:05:00 absolute
GANYMEDE + Protocol Ganymede + AAA-server
RADIUS Protocol RADIUS AAA server
AAA-server local LOCAL Protocol
Enable http server
http 10.10.10.207 255.255.255.255 inside
No snmp server location
No snmp Server contact
SNMP-Server Community public
No trap to activate snmp Server
enable floodguard
Telnet 10.10.10.0 255.255.255.0 inside
Telnet timeout 20
SSH timeout 5
Console timeout 0
Terminal width 80
Cryptochecksum:XXXXX
: end
Thank you... Jay
with pix v6.x, nat/global or static is a must do before the pix will start to transfer packets between two interfaces.
the current static instructions do not cover the translation between the inside and the dmz. as the traffic between pix inside the net and dmz is private, I suggest you to set up no. - nat between the two.
for example
static (inside, dmz1) 10.10.10.0 10.10.10.0 netmask 255.255.255.0
clear xlate
in the above example, pix inside the host must be able to access the dmz Server pointing to the private ip address of dmz Web server.
If you prefer the pix inside the host to access the dmz by name server, then "alias" command should be applied.
for example
alias (inside) 13.13.13.3 12.12.12.17 255.255.255.255
the need for the command "alias" is due to the fact that when pix inside the host tries to access the server dmz by name, the public dns will point to the public IP address of the dmz Web server. now, as the static electricity created for the dmz Web server is directional i.e. public ip will be accessible from the outside, not the pix inside the net. so the 'alias' command will allow the PIX to manipulate the dns response and point the name to the private ip of Web server dmz for the pix inside the host.
-
PIX 515e, multiple VIRTUAL networks on a physical interface to DMZ
We try to set up multiple VIRTUAL networks on a physical interface to the DMZ on a PIX 515e.
The goal is to have logical subnets linked to our single, physical interface DMZ.
Here's what I've tried so far without success:
The switch
-created the vlan 30
-added switchports fa0/1 to 30 of vlan
-attached host 192.168.100.1 in fa0/1
-added switchport fa0/24 to the vlan 1 and vlan 30 with multimode
-interface PIX DMZ connected to fa0/24 switchport
-attached host to switchport fa0/10 172.16.1.55 (vlan 1)
PIX:
Auto interface ethernet2
logical ethernet2 vlan30 interface
nameif DMZ security50 ethernet2
nameif vlan30 dmz2 security50
address IP DMZ 172.16.1.254 255.255.255.0
IP address dmz2 192.168.100.254 255.255.255.0
Results:
-172.16.1.55 has full connectivity to the PIX and beyond.
-192.168.100.1 cannot ping the PIX to the 192.168.100.254 or anything else besides.
Any help would be greatly appreciated. Also, I realize that I could buy a four port NIC and use the physical interfaces, but I can't get the approved purchase.
Thank you
Creation of VLANS on Ethernet1
We want to create a new interface VLAN - VLAN30 and name DMZ2. Also affect the security level 50 in it.
Step 1: Create a physical Interface:
PIX (config) # interface ethernet1 vlan2 physical
Step 2: Name the Interface and set the security level:
PIX (config) # nameif ethernet1 inside the security100
Step 3: Assign the IP address of the interface:
PIX (config) # ip inside 192.168.1.1 address 255.255.255.0
Step 4: Create the logical Interface:
PIX (config) # interface ethernet1 vlan30 logical
Step 5: Name of the Interface and set the security level:
PIX (config) # nameif vlan30 DMZ2 security50
Step 6: Assign IP address to the interface:
IP pix (config) # DMZ2 192.168.100.254 255.255.255.0
Step 7. Switch, set the port where from the inside, to the Isls or dot1q physical interface. Place the sheath in the native vlan2 as in step 1.
-
upper and lower filters in the registry how ca I get it back
in the registry, how can upper and lower filters I get them back. CD and dvd not being recognized
Hello
You are not absent from these filters, you do not want in most cases.
This is for Windows 7 and Vista is very similar.
------------------------------------------------------------------------------------------
Follow these steps to remove corruption and missing/damaged file system repair or replacement.
Start - type in the search box - find CMD top - RIGHT CLICK – RUN AS ADMIN
sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlThen run checkdisk (chkdsk).
How to run check disk in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html==========================================================
After the foregoing:
References to Vista also apply to Windows 7.
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The DVD player does not work after installing Windows 7
http://support.Microsoft.com/kb/975270/The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
Setup after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and the
correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry settings for your
CD/DVD drive someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays
all devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">
-
Lack of upper and lower filters
My cd/dvd drive is missing. I tried the resolution posted with disassembly of the upper and lower filters, but they are not there. I can't find another solution anywhere! Help! Student with upcoming finals and projects to complete. Thanks in advance :)
Hello
Step 1: Please do all the below even if you did before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps and happy holidays!
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
CD/dvd lack tried to delete the upper and lower part in the registry but were not there to remove. tried to delete the device manager that he should not delete and re-start
Hello
Step 1: Please do all the same underneath if you did some before as is often total
a process that solves the problem.Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
below.
Then, work your way through these - don't forget the drive might be bad, could be a coward
cable or slight corrosion on the contacts (usually for a laptop) and other issues.Your CD or DVD drive is missing or is not recognized by Windows or other programs
http://support.microsoft.com/kb/314060 - a Mr FixitTry this fix manually if the Fixit 314060 does not work
http://www.pchell.com/hardware/cd_drive_error_code_39.shtmlYour CD or DVD drive is missing or is not recognized by Windows or other programs-
a Mr Fixit
http://support.Microsoft.com/kb/982116The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
for Windows Vista
http://support.Microsoft.com/kb/929461When you insert a CD or a DVD, Windows Vista may not recognize the disc
http://support.Microsoft.com/kb/939052Your CD or DVD drive cannot read or write media - A Mr Fixit
http://support.Microsoft.com/GP/cd_dvd_drive_problemsCD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
Vista installation after booting from the DVD (AHCI)
http://support.Microsoft.com/kb/952951
Drive CD - R or CD - RW Drive is not recognized as a recordable device
http://support.Microsoft.com/kb/316529/Hardware devices not detected or not working - A Mr Fixit
http://support.Microsoft.com/GP/hardware_device_problemsAnother possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
ends. Remove and replace, do not just tight. For laptops, you can often clean power and
contacts data with a pencil eraser.Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
manufacturer of device to see if there is a firmware or drivers for your drive if necessary.===============================
Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
do it right.Did you follow the Troubleshooting Guide for the reader who still does not work? There are
the entries in registry that the troubleshooter does not solve and those who "might" be the cause.Check with your Maker system and a device for the two possible firmware updates and
the correct registry entries for your car.Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
the parameters.HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}
-----------------------------------------------------------------------
You can probably find more info here and maybe even the exact registry for your CD/DVD settings
drive from someone with the same model.Forums - a lot of expert real help
http://Club.myce.com/CD/DVD units
http://www.myce.com/storage/Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
nothing change) - find the DevManView device and then make a right click on it free in RegEdit.DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
devices and their properties in flat table, instead of the tree viewer
http://www.NirSoft.NET/utils/device_manager_view.htmlI hope this helps and happy holidays!
Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.
-
Upper and lower filters with Windows 7 (32 bit).
My Medion compute'rs DVD/CD player continues to try to start when not used. (flashing on it and noise coming from it, but is not).
Medion support sent me a fix on how to a install and re install upper and lower filters.
I typed in REGEDIT and followed their instructions until I went into the registry editor and click 4D36E965-E325-11CE-BFC1-08002BE10318 to select this key, but I don't see the upper and lower filters listed, to remove via the keyboard in the right pane.
They are listed under a different name. ??
Thanks a lot guys, I'm a beginner and never went in the hidden depths of Windows before.
emember - this is a public forum so never post private information such as numbers of mail or telephone!
Ideas:
- You have problems with programs
- Error messages
- Recent changes to your computer
- What you have already tried to solve the problem
For any question on Windows 7:
http://social.answers.Microsoft.com/forums/en-us/category/Windows7
Link above is Windows 7 Forum for questions on Windows 7.
Windows 7 questions should be directed to the it.
You are in the Vista Forums.
See you soon.
Mick Murphy - Microsoft partner
Maybe you are looking for
-
MacBook pro mid 2010 kernel panic
Hi, I have a macbook pro mid 2010 i7 (ID: MacBookPro6, 2) due to randomly crash a kernel panic. Does anyone know how to fix this? There is the report. Thank you. Anonymous UUID: EAE9FB95-BC9F-D97E-5767-F1D894197AB6 Sun Jul 10 12:49:39 2016 Panic repo
-
Verification code not get two-step for app store purchase.
When you download from the app store, Apple requires the user id and "password followed by verification code displayed on your other devices". This is EXTREMELY vague and badly phrased: -It does not say where to find this code. I guess it's supposed
-
Awesome bar taking me to incorrect pages
When I start typing a URL in the Awesome bar (for example msnbc.com) Firefox starts to load the pages based on my story. Sometimes it seems to block on a page, and even when I continue typing in the URL that I want, and then press ENTER to access thi
-
In desperation... all my email is gone. Empty Inbox, and sent. How can I recover them? Thank you.
-
Office disappeared. Page is black
After the removal of the malware using Malwarebytes, the office is now black; No file list. Help!