PIX506 problem, DNS and server Eachange Cofiguration!

Similar Questions

• To:Patrick.Iseli, Please help! PIX506 problem.

  Hi, patrick!

  Sorry, after you.

  I read your ad article abot PIX506 and NETGEAR DG814 configuration.

  I have somting problem, PIX506 configuration. AND it is similar to your PIX when troubleshooting.

  Please, help me!

  Please see below the text and attachments.

  Thank you!

  Hi, Expert everyone!

  I can't write ENGLISH well, that this will cause a problem of communication for YOU.

  I meet a problem to configure the firewall to PIX506.

  I have a firewall PIX506 and NETGEAR RP614 IP-sharer.

  Under PIX506 firewall, there are two Windows servers.

  A Windows 2000 Server is the Web server and DNS, a different Exchange 2003 server based on Windows 2003 server.

  But the problem is...

  I do not receive an email, please send an e-mail very well!

  I have document attached on PIX506 config and my network diagram.

  It's a crazy problem.

  Please please please help me, get Expert everyone.

  I posted the config in the "problem, DNS and Eachange Server Cofiguration PIX506!

  sincerely

  Patrick

• I keep having problems with my server DNS does not. Computer Blu - Ray player and wireless both have problems with the connection.

  I have problems with the server DNS does not.  I have been using my wireless on my computer and watching netflix on my Blu - ray player at the same time.  The Blu - Ray player froze and wouldn't connect.  At first, I thought that the network has not been configured correctly, but it worked not five minutes before.  I tried many things and I realized it was that my DNS server does not.  Does anyone have any suggestions?

  original title: DNS server does not

  Hi Dwright,

  1. have you made changes on the computer recently?
  2. not the problem only occurs when you watch netflix on Blu - Ray player?

  Method 1
  I suggest you try the steps from the following link to fix the server DNS does not problem.
  a. click on start and then Control Panel.
  b. go to the networking and sharing Center and then click on change adapter settings.
  c. right-click on connection to the Local network and select Properties.
  d. Select Internet Protocol Version 6, and then click Properties.
  e. Select obtain DNS server automatically an address and press Ok.
  f. Select obtain IP address automatically.
  g. Repeat steps for Internet Protocol version 4 as well.

  Method 2
  Try resetting Winsock2 from the following link:

  How to determine and to recover from Winsock2 corruption in Windows Server 2003, Windows XP and Windows Vista (applies to Windows 7)
  http://support.Microsoft.com/kb/811259

  Method 3
  Reset TCP\IP.
  How to reset the Internet Protocol (TCP/IP) (applies to Windows 7)
  http://support.Microsoft.com/kb/299357

  Additional information:
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

• Requirement of DNS and DHCP Server Essentials 2012 home

  I have a Server Windows Essentials 2012 acting as DNS and DHCP server with a domain name for backups etc on my home network. It's that everything works fine, no errors, no problem. Works well actually, telling me when the children did not install updates or restarted.

  I have two groups of users. My sons step, 10 and 12, which I want to use OpenDNS as a provider external DNS with a policy very, very limited and my wife and me who want to use indications of root or Google DNS or any other DNS provider. Others, specific devices no user (box of the xBox, WII, Satellite, TV, CCTV etc.) can use.

  Before the 2012 server, I had a 2 k 3 server running in a virtual machine for DHCP, alone and put my wife and my devices on static reservations with the just and external DNS provider used OpenDNS as the default scope, DNS. Unfortunately different bits of domain services 2012 don't seem to work unless the server of 2012 is the first DNS server listed on client machines (backups failed. Impossible to find other local computers). Currently, this means that we are all using OpenDNS.

  What I would like is a way to say 2012 to send adult group DNS queries to another DNS provider and leave the rest at default to OpenDNS, while still having them register in the original DNS domain. Any suggestions?

  This issue is beyond the scope of this site and must be placed on Technet or MSDN
  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• Apple stop updates iOS 9.3 for older iDevices due to activation server locking problems more and more.

  Latest news of Apple posted, incredibly, ELSEWHERE other than on Apple own site Web/community technical forums.

  Apparently Apple has stopped now updates iOS 9.3 for older iDevices due to activation server locking problems more and more.

  http://www.IMore.com/Apple-working-iOS-93-fix-older-iPhone-iPad

  Someone just posted in another thread that it may be active again. I can't check it, because they haven't posted a link about her being active again, and I've already updated all my devices, I can't be sure. Maybe something to watch.

• I have rcd an aol email asking me to connect to correct problems with the server and took me to an unknown website waqui.press.ma once I've trashed this e-mail my server started working normal is this mail a virus?

  I received an email from aol asking me to log in due to problems with my server, it took me to a website "waqu.press.ma" is an attempt to plant a virus?  Once that I've trashed this e-mail my server was working normal.

  If you are on iOS as implied by your footer, and you provided no identification or such information to the server, you're probably fine.   (Unless your device is jailbroken.  This process turns off a large part of the iOS security.)   If you have provided something IDs, change these now and then determine what other information is accessible using the credentials - the content of mail messages, no password that have been sent to you, etc.

• Windows store error "we could not connect to the Bank. This can occur because of a problem with the server or the connection may have expired. Please wait a few minutes and try again. »

  Original title: Windows 8 store does not.

  Whenever I try to open the windows store, I get the message: "we could not connect to the Bank. This can occur because of a problem with the server or the connection may have expired. Please wait a few minutes and try again. »

  This happens constantly, and because of that I have not been able to upgrade to Windows 8.1.

  Hello

  This behavior can occur if the antivirus application blocking the app Store or changes due to some recent on the computer.

  I would suggest trying the following steps and check if it helps.

  Method 1:

  Make sure that your PC is up to date

  Make sure that updates are installed on your PC and that your antivirus program does not prevent the application from running. For more information about installing updates for your PC, see Windows Update: frequently asked questions.

  Method 2:

  Run 'Windows Apps Store' convenience store

  You must be logged in as an administrator in order to run the "Windows Store Apps" troubleshooter. This tool can automatically find and fix some issues with applications. It is available in English only, but will work in all languages. You can let automatically try to fix any problems found, or select what you want made repairs.

  http://download.Microsoft.com/download/F/2/4/F24D0C03-4181-4E5B-A23B-5C3A6B5974E3/apps.diagcab

  Method 3:

  I suggest you delete the Windows Store cache and check how it works.

  1. Press Windows + R logo
  2. Type wsreset.exe in the run window, and then press ENTER.

  Method 4:

  Define the Apps approved in third program Antivirus- If you have a third party AV program installed, check its settings to make sure that the app Store works is not changed to be approved. If the AV program has the app as unreliable, it will block and prevent opening the app.

  Let us know the status of the issue. If you need help, please after return. We will be happy to help you.

• Laptops acquire wrong address DHCP, DNS and gateway wireless

  I have problems with two laptops. For some strange both acquire the bad DHCP, DNS and gateway (server) respond when I try to access the Internet via Wi - Fi. For some reason, this does not happen when I use the LAN (cable) connection.

  that is instead to fetch the address: 133.24.56.78 (no real address), the system retrieves / uses 111.22.33.44 (again, not a real address). BTW, these two systems are configured to fetch automatically get IP addresses and DHCP. I tried to fix the connection in both cases, but it did not work.

  What can I do to fix this?

  Problem solved.

  I changed the router to WEP (WPA - PSK) encryption.

• DNS and static translations

  I have a web server on my dmz. On the demilitarized zone, the computers cannot be accessed by name. The problem is that DNS returns the ip (real) outside. I need the demilitarized zone to translate it into a local ip address. I use the MDP so I'm not using aliases. Any help would be appreciated.

  You can do this with the [static] commands and the "dns" option

  static (dmz, outside) 123.123.123.123 192.168.1.1 dns netmask 255.255.255.255 [keyword dns tells the pix to DNS doctoring for this translation because DNS resolves the public IP address]

  static (dmz, inside) 123.123.123.123 192.168.1.1 subnet 255.255.255.255 mask [allows the internal hosts to connect to the public IP found in DNS and it translates the private IP on the way to the demilitarized zone]

  Make sure you do a [clear xlate] after the changes.

  If you are running under 6.2, you will have to make any [alias] on the Pix.

• How to set the time between workstations and Server 2008 R2

  Hello world

  I have problem with my Server 2008 R2

  all the workstations on my company doesn't synchronize the time on the domain controller

  I tried many ways to set up automatic synchronization via command prompt (Net time) and its does not work

  Please help me configure the time between the DC and the workstations

  Thank you

  Windows Server forums:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer/

• Is there a problem with the server of Combat Flight Simulator 3?

  Is there a problem with the server of Combat Flight Simulator 3? I can play online because I can connect to the internet.

  I have READ 651,2 Kbps. someone helpme?

  Hi Roy sanchez,

  Thank you for using Vista answers Forum.

  What happens when you try to play?

  Here is a link to a few known issues with Combat Flight Sim:

  http://support.Microsoft.com/kb/331570

  I'm not sure of CFS, but most of the game servers are hosted by the players.
  You can check with your preferred server host to see if they are experiencing problems.

  Please let us know if that helps.

  Chris
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Time problems Syncro and hp Advisor does not.

  Well, I had problems lately, and one of them goes down time syncro. I tried to make the prompt for syncro and do not work.  My computer is a HPa630f.  I keep getting some time is not well actually my time shows that it is.

  Second prob is just started coming up with the hp Advisor

  event name clr203 prob

  Siganture04 mscorlib

  signature prob system. I.O.FileLoadException

  Event Viewer.

  Activation context generation failed for "C:\Program Files (x 86) \Hewlett-Packard\HP. Load Assembly Microsoft.VC90.CRT, processorArchitecture = "x 86" publicKeyToken = "1fc8b3b9a1e18e3b", type = "win32", version = "9.0.30729.4148' is not found. Please use sxstrace.exe for detailed diagnosis.

  Application

  source of event side by side 33 id

  Hello

  Flymar01 wrote:

  Mine is HP a6530f.  I looked on my computer and it was on the list.  Mine is vista 64.  Yes internet time sorry.  I have another question which is supported right now as well.  Which would not interfere with it?

  Try a different time server. Take a read of the present. The hyperlink goes to a well written explanation of how to deal with issues of internet time.

  Kind regards
  ERICO

• WRT54GS2 v1 connection expired and server not found

  OK I got the connection expired issues and server not found on both my PC and my Laptop.I I use Zoom ADSL ISP x 5 provided. series 1605. I have a router Linksys WRT54GS2. I followed the installation program in full and was surfing without delay. The problem started there when I bought the router and plugged in about 5 months. I already spoke with technology specialists to my ISP and they said that I have an excellent DSL connection and they have not seen any problems at their end. I had disconnected the router completely my network and removed the Ethernet cable and hooked the cable directly to a DSL modem and had no problems until I plugged the router in the modem. I factory reset the router a few times and implemented accordingly to make sure everything was good. Well, I still have errors in time-out for laptops and PCs. I have tried almost everything in the book and I'm out of ideas. Am I missing something here? Any help would be greatly appreciated.

  I tried changing the settings through the router and nothing seems to work. I checked both PC and laptop computer for viruses and nothing. I talked to my ISP and they tell me that my DSL connection is excellent and which was not disconnects or connection has expired at their end. It is located between my router and two computers. An Ethernet cable is plugged directly from the computer to a DSL modem. And an Ethernet cable is connected directly to the rear of the router. I am just totally stumped. The internet is totally fine when I cut out the router completely. I have no disconnects when the main PC is connected to the DSL modem with router disconnected completely. I have reset the router completely and followed Linksys technical support online for the T and I still get the connection has expired. Initially, I got a Belkin wireless router and thus became the message timeout through it. I thought something was wrong with this one so I went out and bought a Linksys WRT54GS2 router Linksys Wireless G. can someone offer some advice or ideas that I have not already tried? Please? The wife and I are really frustrated.

• problem reports and solution:

  my window vista show me problem reports and solution, but it doesn't give me any solution. Tell me how can I solve this issue?

  How to fix Windows Update, Microsoft Update and Windows Server Update Services installation issues:
  http://support.Microsoft.com/kb/906602

  1. see the "need help?" Tell us what problem you are having"section of http://support.microsoft.com/ph/6527

  2. you cannot install some programs or updates
      http://support.Microsoft.com/kb/822798

  3. check your WindowsUpdate.log (% windir%\WindowsUpdate.log) to find errors associated with the download/install.

  How to read the WindowsUpdate.log file
  http://support.Microsoft.com/kb/902093

  3 b. errors compared to those listed here: http://www.bleepingcomputer.com/blogs/mowgreen/index.php?showentry=1122 or go to http://windowsupdate.microsoft.com > click on help and Support link in the left pane > solve problems on your own.

  ================

  How to reset the Windows Update settings?
  http://support.Microsoft.com/kb/971058

  ================

  Launch a collateral request for assistance free Windows Update:
  https://support.Microsoft.com/OAS/default.aspx?Gprid=6527

  ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft

• Project and server are not accessible! (175002)

  This is the error message I get whenever I try to use Dreamweaver to connect to my server:

  "Project and server are not accessible! (175002).

  I know that this subject has developed for people using Subversion. But I don't use a Subversion.

  It never happened until I made the last update to Dreamweaver.

  Please notify.

  Thank you!

  The f

  Because this is a Subversion error, I suspect that Dreamweaver tries to access the repository, and as you have not, you get the error.

  How to solve this problem is to develop the files Panel by clicking on the icon at the far right:

  

  Then select the icon for the remote server.

  

  You can then restore the files to normal size panel. This should solve the problem.