PORTS (COM & LPT) is more visible in the device controller speaker?

Similar Questions

• Ports (COM & LPT) does not not code 10

  Hello, im trying to COM with my PC and the mobile phone using J2ME and J2SE, but when I ask for the COM windos anything happen I check the Device Manager and the Ports (COM & LPT) wasn't there, so use the Action menu select Add legacy hardware.
  
  After installation I get the exclamation "Warning" Code 34 and the following comment "Windows cannot determine the settings for this device.
  So I use this tutorial "http://lifewithdotnet.blogspot.com/2012/02/how-to-add-physical-serial-port.html" for the configuration manually.
  Now I have another exclamation Point "Warning" Code 10 of the commentary 'this device cannot start' I have tried to disable then enable the component nothing happen.
  Looking for an update of the component said that its already been updated.
  How can I fix this error?
  PS actually the USB ports work! If I connect a printer USB Flash drive, IPOD, even my work cell fine sound when im trying to get an answer for java that the list of ports is delivered empty, I tried the java SE & ME in the other laptop and it works so I don't think its java.
  I use a Dell M5040 with AMD processor C - 60 Service Pack 1 of Windows 7 Starter.
  I/O 03F8 - 03FF used by: Bus PCI which is not job icon
  IRQ 0 x 00000004 (04) used by: ACPI x 86 computer that isn't job icon.
   

  Hi Charlie,

  In order to change the hardware parameters, you should contact your hardware vendor. Microsoft will not be able to help you change the hardware settings.

• DVD/CD drive is not visible in the Device Manager, but it works.

  Original title: My dvd/cd drive is not visible in the Device Manager but

  This works because I have jst begin with him. I can hear the disc running, but nothing ever comes and when I go to computer its not visible there either.

  Hello

  See the methods listed in the article mentioned below.

  My drive does not appear in Windows Explorer

  http://support.Microsoft.com/kb/330140

  Important: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems can occur if you modify the registry incorrectly. Therefore, make sure that you proceed with caution. For added protection, back up the registry before you edit it. Then you can restore the registry if a problem occurs. For more information about how to back up and restore the registry, click on the number below to view the article in the Microsoft Knowledge Base: 322756 how to back up and restore the registry in Windows.

  See this link to view the hidden devices:

  http://msdn.Microsoft.com/en-us/library/Windows/hardware/ff553955 (v = vs. 85) .aspx

  I hope this helps!

• Comm port not detected by VISA / MAX after the device power cycle connected

  I have a device communicating via USB virtual comm port. The device and labview program both work very well, most of the time. The program is designed for the automatic connection for the connected equipment. It works perfectly when I unplug and reconnect the USB cable.

  However, if the unit power cycled as the USB cable is connected and the program/vi is running of things go wrong. The device enters a phase of boot loader for a few seconds to the power upward, if labview tries to query the port comm during this phase the comm port is corrupted in some way and is no longer recognized by VISA / NI MAX. However, other programs, hyperterminal, etc device manager can see and communicate with the port when the boot loader is complete. For Labview / NI MAX to see the port I have to physically disconnect the USB cable. The program does not need to be restarted in order to detect the port comm again and, infact, labview is restarted or my compiled program does not solve the problem. Physically disconnect the USB port allows visa / MAX OR see the port is connected.

  It seems to me that there is a problem with VISA where somehow if a device is not correctly identified by VISA during the first attempt it just does not take into account the port until a physical intervention. Is there a way to force VISA to reassess completely all connected comm ports?

  Hello MJanus,

  As far as I know, most of the virtual com ports are not fully supported by VISA so some quirks in its operation are to be expected: http://digital.ni.com/public.nsf/allkb/6E1922B526572CB8862571AA00544057?OpenDocument

  Officially, we do not support the use of com virtual ports, if unfortunately, the feature you have now is probably as good you'll be able to get with this configuration. I know it's not the answer you were hoping to hear and I apologize for the inconvenience, but it is not really possible visa work well with all software virtual com port due to the wide variety of products available.

  Kind regards

• I accidentally changed a few settings on the appearance of my mail on my IMac screen. The top bar is therefore more visible all the time, and the screen seems now exit by moving to the left. I want to restore valuable appearance and method to quit smoking

  The top on my mail page bar is no longer visible, unless I hover.

  The screen seems out by moving to the left.

  How do I change them?

  I don't want to say 'previous' and not 'valuable '!

• USB port / drive F does more cannot download usb devices

  I think that my drive F (usb port) stopped working. It will not read any of my devices that I connect to download what is the problem?

  I think that my drive F (usb port) stopped working. It will not read any of my devices that I connect to download what is the problem?

  Tips for solving problems of USB devices.

  http://Windows.Microsoft.com/en-us/Windows-Vista/tips-for-solving-problems-with-USB-devices

• My device used to be included in the device under the turbine BP & COM port section manager now it is hub USB root and I can't connect with my camera. Help

  I have a machine that uses a USB to serial connection, after I installed the driver in my computer, it finds the machine and load the device in the ports COM & LPT, but this morning for some reason, he shot my device in the USB root hub system. How to get out of there and recognized him as a COM & LPT device since it is a USB to Serial Port that I can discern the number COM port so that my computer can communicate properly?

  Hello
  
  1. What is the model and brand of the device?
  2. do you see any red or yellow bangs in Device Manager?
   
   
  a. in device, right-click on the Device Manager and select Properties.
  b. now in the Properties window, click on the tab General Post back the message found underdevice status.
  
  Open the Device Manager

  Thanks and greetings
  Umesh P - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.
  [If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message.] [Marking a post as answer, or relatively useful, you help others find the answer more quickly.]

• Output Multipal Modem and Ports Com Usbs without deleting the driver...

  In my laptop I don't connect to many cell phones, now my problem is my Ports none is going too far and I do not use affected old Ports so I tried to find Solution on Web... I Manage to find Solution but I stuck when it comes to too many Ports... I want to release too many Ports in a short way.

  What I find Solution on the Web...

  Run elevated command line Device Manager:

  > set DEVMGR_SHOW_NONPRESENT_DEVICES=1
  > devmgmt.msc
  
  

  Turn on "Show hidden devices" in the menu and uninstall gray COM ports.

  After the display of hidden devices, it's hard to uninstall devices one by one... I want to erase a single Type of devices in a single order without deleting driver device because my goal is to free Ports as much as Possible without removing the device driver...

  

  Hello

  Currently, removing the devices in the Device Manager is possible, one device at a time. This is because each device has its own corresponding entries in the system files and registry.

  Kind regards.

• Satelltie M40X: NIC disappears from the Device Manager

  I have a Satellite M40X with Windows XP SP2 and my card (Realtek gigabit) network is no longer seen by Windows (or Linux: test performed with a Ubuntu live CD).

  The lan card is not seen by Toshiba HW Setup. I disappeared 2 days ago, was back yesterday that a d is not present today...
  LAN card is enabled in the BIOS.

  Can someone help me solve this problem?

  The PC is 13 months (out of warranty Toshiba...)

  Some registry keys are damaged and so the LAN card is not visible in the Device Manager (very possible) or the LAN card is damage (more)

  I think you should try to reinstall the operating system. If after installing new network card is not visible in device (such as unknown device or network card) Manager then it s a bad material work and in my opinion, that the replacement or repair will help.

• Advanced Port Replicator III more compatible with the Portege R200

  I just ordered a new Portege R200 and above-port replicator... However, I note that the R200 is not listed in the list of laptops supported for this Replicator! Can anyone confirm if I have made a mistake and need to change the order?

  Will be

  I visited the area Options & accessories on the European site of Toshiba, and like you said the Portégé R200 is not listed in the list of mobile phones compatible.
  So I assume that the Advanced Port Replicator III more (PA3474E-1PRP) does not support the protected R series.

• Read the serial number of the device in LabView COM port

  Hello

  Is it possible to read a device COM port number in LabView? I would like to make an initialization of the program following the right port COM of a device, for example a USB temperature reading device, and set the COM port as the correct port at the start of the main program of LabView. I want to do that, because a USB device gets usually different dedication of COM port on different computers. Our application runs on 80 different computers. A program like that would be very nice.

  Can someone help me?

  Paal

  Another thought. It also has a place where certain standards can save you a lot of time.

  You have 3 dongles by machine. When setting up a computer are these three dongles * always * assigned to, for example, com 3, com 4 and com 5.

  Similarly, always check that instrument 1 is always on com 3, tool 2 is always on com 4 and 3 device is always on com 5.

  This convention will also simplify debugging...

  Mike...

• lack of port com & Red Cross sign to the MAX (device in unknown state? offline)

  Hello world

  I have three serial ports on our lab computers, one is the default on the motherboard port, and two others are usb connectors of the series. The problem is the default com1 serial port has a cross write in MAX and two other serial ports are missing. All serial ports displayed correctly in windows XP Device Manager and in the register too. The version of labview is 8.5.1 with NI-visa 4.4. See attached photos.

  I have many hours of research and have not found a clue. Please help me.

  Thank you!

  Eric

  Hello

  Have you tried clicking the button solve the problems in the device status section? It is the first time that you have connected these devices to your computer, and you can see the virtual com ports on another computer in the laboratory?

  Kind regards

• Need to identify the designation of port COM through BACK...

  I'm editting a program that sends and receives information to a device via a USB - serial adapter. Previously, the program has been run only on one pc which always use the same COM port when the device is connected. Scripts used with this program have been written to always specify this port. After having taken the device and connected to another pc, the pc allocates another COM port - this is a relatively easy task for me to go through the device management and identify the appropriate COM port, modify the script and get the device communicates with the pc. HOWEVER, in the future, communication must be maintained between the device and a laptop with any user.

  The program you are using may open a windows command prompt and run DOS commands. If possible, I would like to help you find a way to use BACK to identify the COM port used by the USB adapter so I can assign this port number for a variable to be used in scripts, creating their infallible to any user.

  Thanks for your time,

  Chris

  Hello

  To improve assistance to this subject, you can ask your question in the MSDN forums.

  http://social.msdn.Microsoft.com/forums/en-us/categories

• on port 162 java.exe running. I tried to kill him with the command prodess k 1289. 1298 here is the process ID. but it comes back again. I need the port 162 for sending traps.

  original title: port162

  Hi, on port 162 there is a process called java.exe running. I tried to kill him with the command prodess k 1289. 1298 here is the process ID. but it comes back again. I need the port 162 for sending traps. I first removed java completely from my pc, but still there was this java.exe. in fact, there are two java.exe if I check in the running task manager. need help. I also ran antivirus as well as anti-malware software, but no difference.

  Hello

  I suggest you to visit these links and check if it helps:
  http://www.Java.com/en/download/uninstall.jsp
  http://Java.com/en/download/help/regkey_addremove.XML

  Have you tried to change the port to Java? See this link:

  http://www.Java.com/en/download/help/proxy_setup.XML

  It will be useful.

• The button "Toggle Navigation" difficult to see on mobile screens, I need help to make it more visible

  Hi, I'm pretty new to dreamweaver so excuse me if this question is stupid or the obvious answer.

  I created my first project in dreamweaver - a "Coming Soon" page for my site Cyber Zombie Coming Soon! and I'm pretty happy with the results considering it was my first time using dreamweaver for a real project of myself without a tutorial.  However, I have a problem with my navigation menu. When my site is displayed in desktop mode, the navigation is fine (screenshot)

  

  But when I reduce the size of my window to represent a mobile , the button interface that is supposed to say "Turn the Navigation" is extremely difficult to see (screenshot)

  

  When I hover over the button with my mouse, it's a little better but still difficult to see (screenshot) and also you do not have a mouse on a smartphone to get high with.

  

  Is someone can you please tell me how I can remedy this. I need the button 'Toggle Navigation' to be more visible, but I don't know how do to change what I used a "bootstrap" navigation menu which had the button built in.

  Thank you

  Jason

  Hi Jason,

  Try to change this:

      

  to do this: (light text on dark background)