Ports used by Uptime.exe

Similar Questions

• To configure a serial port using Max

  Hello

  I inherited the code that configures the serial port using the old serial code that does not allow the user to specify the term tank and turn on the tank of the term. Any ideas on how this is done with the old serial code? I also tried to use MAX to set the term tank and allow it, I am able to communicate with my device series with Max and I saved the changes when I was. So when I run Labview code, my serial code fails because the term tank is wrong and it is also not enabled.

  Everything that happens with the definition the term tank and allows ideas?

  What you do to the MAX to the extent where the configuration of the serial port have no impact on the LabVIEW program. (EDIT: which means that you can change the configuration in the LabVIEW code.)

  If you load the old code in a version of LabVIEW using VISAS for all the stuff of series then the screw would have been automatically replaced by shell screw that NEITHER created for the old code. Inside, they use just VISA. More than probably the old code use via digital port numbers. For example, in the library of \vi.lib\Instr\serial.llb of , you will see these shell screw Serial Port' writing' for example, calls the 'Open Serial Driver' VI which simply returns a VISA session. It then uses the Write VISA. So you can define characters of termination by obtaining the VISA of "Serial Driver Open" resource.

  Of course, the best solution is to rewrite the code using VISA directly. It will be much cleaner.

• How to transfer files from PC to PC via a serial port using labview

  I need to transfer files (.txt, .doc, .xls) from PC to PC via a serial port using LabVIEW. Is it possible to transfer files, if so how to transfer?

  Yes, it is possible to transfer files with the serial port using LabVIEW.  The files are just collections of bytes and the serial port is good enough in the expedition of the bytes from one PC to another.  You must connect the ports series with a null modem cable.

  First, take a look at the example of serial communication.   In LabVIEW, go to the Help menu and select «Find examples...» ».  From there, you can search for "serial" or navigate to hardware input and output > series.  Select «Write series base» and Read.vi  Try this example to gain confidence on the serial communication methods.

  Then it's time to learn how to read and write files.  For this, the examples might be somewhat confusing as they deal with files that are presumed to have data of a specific type in them.  I would recommend just familiarize yourself with the functions in the file e/s palette.  Specifically, familiarize yourself with the following functions.

  1. Open/create/replace file - on the side of your destination, you will need to create the copy of the file you are trying to transfer
  2. Close the file - when you're done reading or writing to a file, you must close it.  It cleans the memory used and finalizes write operations that are still floating in the write buffer.
  3. Read a binary file - is the best way to play a file when you don't really like what type of file it.  In your case, you just want to get these read bytes and sent so they can be written down instead of destination.
  4. Write to a binary file - next to the destination, is what will store the bytes in the file that you created with the number 1.
  5. Size of the file get (under the range of the advanced features of file) - you need to know how big the file is, so you know when you are finished.

  OK, so once you are able to create files byte write and read bytes from existing files, you can move forward.

  I suggest the basic method is to have the user specify a source file on the source PC, and a folder on the destination computer.  Then find the size of the source file using the number 5.  Divide this number of size by the number of bytes that you want to transfer to the times.  The series pads are usually around 32 k (if I remember correctly) in order not to exceed that.  Now start to send data by reading a number of bytes and this string output wiring to the feature of writing VISAS.  On the side of destination, you will want to monitor the serial port for bytes and read when they arrive.  This string of yarn to the writing of the function of binary file to add them to your destination file.

  This is the basic outline of how to do it.  He needs to not to overload him write and read buffers on the serial ports.  Initially, you can use delays on the side sending to make sure that the side reading has enough time to digest.  To make things faster, you can bring in a control of flow.

  If all that sounds a little intimidating, there are there Alliance member companies (such as the automation of PrimeTest) who can write this code for you and even provides a turnkey for you solution.

  Happy wiring,

  Dan press

  Certified LabVIEW Architect

  PrimeTest Automation

• Cannot change the name of transcoded wallpaper - file supposed to be in use by dmhkcore.exe

  I have a wallpaper that I can't remove.  It does not try to replace it with any theme.  recommended action is to change the name of old but supposed to be in use by dmhkcore.exe file.  I can't find any reference to this file anywhere.  Help!

  I have a wallpaper that I can't remove.  It does not try to replace it with any theme.  recommended action is to change the name of old but supposed to be in use by dmhkcore.exe file.  I can't find any reference to this file anywhere.  Help!

  Start in safe MODE.
  Rename the file there.

  dmhkcore.exe is a display manager easy belonging to DisplayManager of Samsung Electronics.

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• I just installed lightroom cc on a brand new and reveived laptop 2 following errors.  can someone tell me what they mean and wll prevent of sing lightroom?  ERROR: third charge useful Installer vcredist_x64.exe failed with exit code:-2147024546

  I just installed lightroom cc on a laptop computer brand new and reveived errors the following 2.  can someone tell me what they mean and they will prevent to use lightroom?

  ERROR: third charge useful Installer vcredist_x64.exe failed with exit code:-2147024546

  AND

  ERROR: Cannot install the Microsoft Visual C++ 2012 Redistributable Package (x 64). Please try to install by double-clicking the executable file to "C:\Users\CHRIST~1\AppData\Local\Temp\{7A86BA4B-C59E-4130-9C4D-DA8765643E21}\Lightroom_6_ LS11\payloads\Microsoft VC 2012 Redist (x 64) \vcredist_x64.exe", or download and install the 2012 Microsoft Visual C++ Redistributable Package last (x 64) Microsoft Web site - www.microsoft.com

  Download Visual C++ Redistributable for Visual Studio 2012 updated 4 of the official Microsoft Download Center

• change the port used by apex 4.0

  Hello
  
  How can I change the port used by apex? For example, instead of 8080 I want to use 8081
  
  Thank you

  If you use OC4J, or any other application server, but you do not use the EPG you must reset the EPG

  exec dbms_xdb.sethttpport( 0 );
  

• How can we change the TCP/IP ports used by LabView?

  I'm under LabView 8.2 on a computer running windows XP sp2.  This computer is connected to a compact RIO via Ethernet.  The system works very well, but now I am trying to add an IP intercom function (acoustic digital ii3) this intercom uses a program called talkMaster to communicate with the host computer.  I can't communicate with the intercom because this program needs of ports 3000,3002,5000 and 5006.   I used a program called Currports to see what ports are used, and a program called lkcitdl.exe (National Instruments Logos product name) uses port 5000.  Is there a way to change this? I contacted digital sound technical support and they said there is no way to change it at their end.

  Any help would be greatly appreciated!

  Thank you

  Jason

  I believe that we have an article on this somewhere, but I don't have a link at the moment. Under Windows, you can set the port range used by the protocols of Logos in the registry. Reach

  HKLM\Software\National Instruments\Logos\Ports

  You will find two values DWORD here, FirstClientPort, and FirstServerPort, which defaults to 5000 and 6000 respectively. Logos will search for the first available port in the range [FirstClientPort, FirstClientPort + 1000] or [FirstServerPort, FirstServerPort + 1000] when starts a server or a client. By adjusting the registry, you should be able to find a port range that does not conflict with your software. You need to restart all programs OR after you make this change (probably easier to simply restart the computer).

  -J.D. Robertson

  National Instruments

• Mozzilla not respounding high cpu use plugin - container.exe computer is totally locked

  I start up firefox, and go new. Sometimes it allows me to watch for a while. without warning mozilla not respounding computer is completely locked. I try to stop the program (mozilla) sometimes it allows me, and other times it takes several tries to stop. Mozilla said plugin - container.exe CPU high usage. Happened several times in recent weeks. I updated several times without success.

  Like most of the commonly used web plugin, Flash is the most likely the cause. I don't know why the problems increased with Flash with the combination of Firefox 41 and 19 Flash. I think that people who work.

  For now, I suggest the following to minimize potential problems with Flash in your troubleshooting:

  (1) to avoid unnecessary pain on the sites where the Flash is not really essential, try to set the Flash on Click-to-Play (Ask 'activation'). This will delay the Flash start on a page, until you approve.

  To set 'Ask to activate', open the page modules using either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click on Plugins. Search 'Shockwave Flash' and always change 'enable' to 'ask to activate '.

  With this setting, when you visit a site that wants to use the Flash, you should see a notification icon in the address bar and usually (but not always) one of the following values: a link in a gray rectangle dark in the page or an information bar sliding between the toolbar and in the page area.

  The plugin notification in the address bar icon usually resembles a little Lego block, dark gray. (If it is red, Flash must update.)

  The delay in the activation of Flash can help distinguish between the problems caused on the initial page load, put in folds and script activation vs Flash/loading bar.

  If you see a good reason to use Flash, and the site looks trustworthy, you can go ahead and click on the notification icon in the address bar to allow Flash. You can trust the site for the time being or permanently.

  But some pages use Flash only for tracking or play ads, so if you do not see an immediate need for Flash, feel free to ignore the notification! He will just stand here in case you want to use it later.

  (2) consider rolling back at the end of the extended support of Flash 18. We make the security updates, which you can find if you scroll down half way down this page: https://www.adobe.com/products/flashplayer/distribution3.html - it's for plugin-based browsers, MSI or EXE format should work.

  Most likely, you need to remove Flash 19 before this installer works. This article has a link to the uninstaller program: https://helpx.adobe.com/flash-player/.../uninstall-flash-player-windows.html.

• Connect iPad Pro 12.9 "on PC 3 USB port using the new USB 3 iPad camera connection kit

  Hello. I would like to connect my iPad Pro 12.9 "to my PC using the speed of the USB 3 port of lightning of the iPad for faster synchronization with back ups. I bought the new camera USB 3 connection and A kit to A 3 USB cable, put everything together and down to iTunes, but it does not recognize the iPad. Has anyone tried this before?

  You don't need the Camera Connection Kit for this. Connect your iPad to your PC using the lightning to the USB cable supplied with the iPad.

• Tecra A10 erratic mouse then freezes when serial port used for something else

  MT Tecra A10 was beautiful, but has developed a growing problem. It is running win7 ultimate. When you connect anything serial port wise it blocks indicating the Mouse / touchpad. USB mouse feezes completely, 98% frozen touchpad series same happenes when connecting via a usb emulator. Software on the laptop using series includes RS logix, perfect Omron CX1 Motion and NQ Designer, that said that they worked, can anyone guid help me pls.

  See you soon

  Martyn

  Hello

  Eventually, the software that controls the serial port or the device connected to the serial port is not fully compatible with Win 7.
  I think that this should be checked first.
  Maybe one of you should look for the Special Forum of the manufacturer of the software for more details

• How can I extract and use the driver "exe" to communicate and to load an Excel "cvs" in my Amateur Radio transceiver?

  I use a Mac Mini OS 10.11.3 (El Capitan) processor 2.5 GHz intel Core i5.  With 16 GB of ram at 1600 MHz kDDR3.  I down loaded the program I need and you used my (Mac) excellent program to load the cvs program sheet.  However, the driver is contained in a 'exe' format and I can't or can extract my Mac to use this program.  This driver is required to enable communication between my Mac and radio transceiver.   The only option I see is to acquire a computer laptop windows to allow the use of this application unless there is a program bootable can I mix on an external hard drive and then use Bootcamp?  Help please.

  Try using CrossOver Mac, or install Windows in Boot Camp or an emulator such as VirtualBox or Parallels Desktop.

  (139948)

• Blocking ports using a virtual Super Hub 2ac (VMDG490) machine

  Hi all

  My first post and hoping that it is in the right place. A few days ago, I received my upgrade to a SHub1 to SHub2ac. After a speed problem. I created 4 blocking rules port for one of my computers successfully, but when I try to create the same blocks for my other computer I get an error of "the port selected range overlaps with an existing rule".

  I gave the rule a new name and have obviously used the ip addresses of the other boxes on the network. It worked well on my old SH1 then why not on an alleged update?

  VM, I called and they had no idea if it was possible and showed me tech, alas, they had no idea that is then reported to me their salary for support Dept. They said it couldn't be done? As a Department tech VM and the pay per help guys were unable to offer advice, other than to block ports through your firewall software. Can be done using Bitdefender, I can see (it's another can of worms in itself).

  Any help or advice of Netgear technicians or other users of the popular home network. As seems a downgrade of the former 1 SuperHub that would allow any amount of blocks of port by using port numbers providing the name of the rule was different and the IP addy has been changed, is there a possibility of a upgrde of firmware to re - enable this option? Or the guys from VM need to RTFM

  Any help is much appreciated in this matter.

  Best regards.

  Fubar

  sent you a PM response

• CAN transmit/receive same Port using USB-8473?

  Hi, I'm new to the CAN interface. I have a USB-8473 attached to my USB using Labview 11. I write labview routines to use the port, but since I don't have 2 of them, I thought just to transmit a data frame and read it on the same port for testing purposes. Currently I'm using transmission same reception Port.vi example, just to see, if it works, but when I run the VI and transmit data and then set the RTR bit to receive the rear frame, nothing is ever reported. Are there any additional settings I should do before using the device CAN 8473. I even tried setting the attribute of free reception as well and nothing ever gets the spokesperson. I use a baud rate of 125K on CAN0 flow. Can someone help me understand why it does not work?

  Thank you.

  No.... everything will be virtual (pass on 256, 257 reception). NI-CAN comes with two virtual ports internally interconnected. They are not exactly the same as a real port, but it can help you to carry out tests.

• Service using SRVANY. EXE has stopped working on Windows Server 2008 R2

  I have a Windows Server 2008 R2 (64-bit) server that runs as a service for several years a virtual machine VMware Player.  I used the SRVANY old Resource Kit tool. EXE to configure the Windows 8.1 virtual machine to load and run in the background.  This config worked without problem for years and through at least an upgrade of the virtual machine operating system.

  02/06/16, I upgraded VMware Player to version 12 and later upgraded the virtual machine OS Windows 8.1 to Windows 10.  After that, the service that I created using INSTSRV and SRVANY is more years launches the VM.  The service seems to start with success (no errors), but the virtual machine does not start.  I don't see a new instance of the vmplayer.exe process when I start or restart the service.

  Other changes on the Windows Server 2008 R2 server since the last SRVANY config worked were last month security patches.  I have a hard time to believe that upgrading the guest OS could have no relevance here.

  To troubleshoot, I tried vmplayer.exe followed of the file name of the VMX virtual machine from a launch command line.  This works.  However, if I try to run the same exact command from a CMD, launches of VMware Player interface file, but I get a "file not found" dialog box, and the virtual machine does not start.

  I also tried reinstalling VMware Player 12 and temporarily return to VMware Player 6.  None worked.

  Ideas?

  Subscribed to the thread and ping relevant resources.  Good luck