Similar Questions

• is my Virgin media Super hub 2ac causing AirPort Extreme restart?

  I'll try and make this short.

  I recently had a hub great media virgins 2ac upgrade to a great hub. Before that, I have not had any problems with my network or wifi. And became 150 MB of download and upload 12.

  I have two extremes of the Apple Airport, one as a primary router and the other as an extension of network (super hub is modem mode) the extreme second is connected via Ethernet to a voltage adapter.
  The problem is that if I use a wired device or wireless broadcasting data continuously for more than 15-25 minutes (22 minutes is the sweet spot) and then the main AirPort Extreme will restart and drop the wifi.

  I did the following:
  Restart all devices (works temporarily)
  Changed all wifi channels
  Off to IPv6
  Bought a new AirPort Extreme
  Bought new cables
  Hard wired devices previously on wifi

  The key is that I'm out of ideas. The only thing that has changed is the super hub, everything else is the same. Is it possible from that great hub is the original AirPort Extreme resets automatically?

  Any help welcome because it leads me to the top of the wall!

  One thing that comes to mind. You mentioned that you have placed the new super hub modem mode. Do you know if this also turns off Wi - Fi hub as well? If it does not then it is possible that you found the Wi - Fi interference between the super hub and AirPort Extreme connected on it.

• Extension of WiFi using the Virgin Super Hub and Airport Extreme

  I am trying to expand the network so that I get better WiFi in another area of the House.  I have set up a unit of the Airport Extreme (AE) and through the Airport utility, I see that it is picking up the WiFi network and get the green light.  When I click on the device in Airport Utility (AU) to check the information of the AE is indicating that it is on the WiFi network and the right connection.   None of my devices (iPadAir 2 and iPhone 5) are picking up the WiFi Signal.  However, when I click on change EI is indicating a Base Station.  So clicking on wireless and network Mode, then click on extend a wireless network by clicking on update of the unit could not leave the stand mode.   Very strange!

  Routers Apple do not work as universal repeaters... they extend ONLY other airports.

  You can't do what you want. You MUST connect the extreme by ethernet on the Super Hub... or use adapters EOP.

• No matter which usb port I use for a usb hub

  I have a compac presario CQ60-215DX notebook and I want to install a usb hub. No matter which usb port I use? would also like to know if it is necessary to remove it to restart my computer"

  Thanks for any help.

  Karen

  The only time you usually get trouble with USB ports is when you mix both USB 3.0 and USB 2.0 devices.

  • For all USB 3.0 is backward compatible, it is simply not the case that all the older devices are USB 3.0 compatible.  If you have a problem with an older device, consider that it may be because it is plugged into a USB 3.0 hub / port.
  • Not all hubs are created equal.  If you try to run some devices high speed (things you plug a hub) on a lower speed (2.0) turntable, they may lose the integrity of the data (Act funny) or refuse to perform certain tasks (depending on the device).  These devices may work best when it is plugged directly into the computer no matter that they are running as the USB 3.0 or USB 2.0.  It is not, therefore, necessarily what port the hub is connected - rather, it could be the hub itself (if you have problems).

  Peripheral USB could better with a reboot - some may not reset at all without rebooting.  A USB hub, one of the simplest types - these are usually plug-and-play.  That's all that is connected to the hub, which could be the determining factor for the restart.  It's Windows - it is always better to restart when things change.

• AirPort Extreme and Virgin super hub

  Hello

  I have a new hub great vm that I put in place in modem only mode and then using my AirPort Extreme of 2nd generation as the wireless router. Is there a reason why I would see lower broadband speeds like that implemented just vs using the super hub in router mode full. I get very fast BB with just the hub acting as the wireless router but it drops by half or even more with my extreme up to game. The problem is that the hub has the power of the terrible wireless signal? I was wondering if it's because of my extreme 2nd generation? Or perhaps a setting that is incorrect.

  appreciate any advice.

  Thank you

  PHil

  A 2nd generation AirPort Extreme is at less than 7 years and that almost 9 depending on where you purchased the product. On average, the useful lifetime of a router designed for domestic use is... average... about 5 years.

  You can reset the AirPort Extreme back to default settings and then set ip all over again, but frankly, I doubt that this will result in a significant improvement. Let us know your results if you decide to try it.

  If you decide to try a new router, AirPort, Apple offers a 14-day return privilege, so if one new product is not the way you want, you can return it for Exchange or refund.

• How to determine if ASA is blocking port or not?

  Hello world

  I support the ASA according to the customer. I'm new to the world of the SAA.

  Users especially to check whether or not ASA allows specfic port.

  I don't know how I can check that.

  Is it possible that I can determine if ASA is blocking port or not?

  If ASA is blocking port what steps I must take to allow ASA allow specific port?

  concerning

  Mahesh

  Hello

  You can use the command packet--draw to get the results you're after... that is to say if a 10.1.1.10 client attempts to access google dns, you can use the following syntax:

  plotter of entrance inside the 10.1.1.10 udp packets 53 8.8.8.8 53 detailed (I may have the syntax a bit but you can tab your way through this).

  Thank you

  Sent by Cisco Support technique iPad App

• What are the ports used by the Cisco VPN Client?

  Hello

  I need to open my outgoing traffic on my firewall to allow two interns (LAN) Cisco VPN Client to connect to their Internet virtual private network.

  I already opened the port 500/UDP, but they are not able to connect. If I open all outgoing ports, they can connect.

  What are the ports used by the Cisco VPN Client?

  Thank you

  You need to open:

  UDP 500

  ESP protocol

  You must also open the UDP 4500 port (if using NAT - T).

  In addition, if the clients are connecting to a VPN 3000 Concentrator series and it is configured for all other options of NAT-transparency, corresponding ports must be open. By default:

  1. If using IPSec over TCP 10000, then open TCP 10000.

  2. If using IPSec over UDP 10000, open UDP 1000.

• blocked ports affecting http

  On recommendation of Cisco, I have blocked ports TCP 3127-3199 out my interface "inside". Seems that these are commonly used for mydoom ports. Now, when the user's browser uses these ports as source ports they don't have until it exceeds this window. Has anyone seen elsewhere this problem and how do you work around it?

  Roland,

  A MyDoom attack can be launched from the outside (entering your local network) or inside (out to your local network).

  IF YOU WANT TO BLOCK INCOMING OF MYDOOM ATTACKS:

  If this traffic passes through a firewall, then by default, the sessions opened from the outside are blocked unless explicitly allowed entering. If you use a router with ACL, then you must configure an ACL in the INCOMING direction and apply it to the interface from the OUTSIDE as such:

  --------------------------

  For routers:

  access-list 111 tcp refuse any any 3127 3199 Beach

  interface

  IP access-group 111 to

  --------------------------

  In this case, you'll experience the question that you're already because when a web server returns a bunch of session to the client (browser), then the destination ports match the ACL and the router will drop the session. To remedy this, we can apply an IOS Firewall to the external interface of the router. The ACL to block incoming attacks of MyDoom cannot while the router will maintain session state information in its table.

  IF YOU WANT TO BLOCK OUTBOUND MYDOOM ATTACKS:

  Then the ACL must be applied 'in' on the 'inside' interface

  --------------------------

  For the PIX Firewall:

  access-list 111 tcp refuse any any 3127 3199 Beach

  access ip-list 111 allow a whole

  Access-group 111 in the interface inside

  --------------------------

  --------------------------

  For the router:

  access-list 111 tcp refuse any any 3127 3199 Beach

  interface

  IP access-group 111 to

  --------------------------

  This should provide you with enough information to work on your issue.

  Paragraphs

• Oracle cloud virtual image, I was able to create the database using DBCA (virtual image) oracle cloud. I understand with the virtual image, we won't have a lot of tools like on DAAS cloud... But could please at least use us dbconsole?

  On oracle cloud virtual, image I was able to create the database using DBCA (virtual image) oracle cloud. I understand with the virtual image, we won't have a lot of tools like on DAAS cloud. But could please at least use us dbconsole?

  
  I tried to start dbconsole, and it did not work:

  [oracle@ltutest ~] $ emctl start dbconsole

  OC4J Configuration problem. /U01/app/Oracle/product/11.2.0/dbhome_1/OC4J/J2EE/OC4J_DBConsole_ltutest.compute-aulatrobeu83140.oraclecloud.internal_ORCL not found.

  
  

  According to the oracle help doc center - "creating a database on an instance of virtual image service" (http://docs.oracle.com/cloud/latest/dbcs_dbaas/CSDBI/GUID-29290A81-8798-4988-848E-77A1BE0CF08A.htm#GUID-4851560B-D4B6-42...)

  database was created with the option as:

  emConfiguration - NONE - storageType FS

  
  

  I guess we have to manually configure the em console, but when I tried to create it, he told me that "' Dbcontrol repository already exists." "

  When I try to start it, it exports the error

  [Oracle@ltutest ~] $ emctl start dbconsole

  OC4J Configuration problem. /U01/app/Oracle/product/11.2.0/dbhome_1/OC4J/J2EE/OC4J_DBConsole_ltutest.compute-aulatrobeu83140.oraclecloud.internal_ORCL not found.

  Could someone could give me help with this problem?

  
  

  Thanks Brian. I tried your command, and it works. Now I've encountered another problem, how can I browse the URL?

  I created the access rule for access remote on port 1521 and 1158. but when I try to browse the EM console URL, it does not work. all the configurations that I need to do?

• Need help to add serial port to a virtual with "Output to the file" computer in PowerCLI

  I have a requirement where I have to add a serial port to a virtual computer that is an Ubuntu operating system and the port type must be 'output to the file"with a file name specified in a data store on the same ESX host.

  Can anyone provide me with a script of powerCLI for this please?

  Thank you very much

  Suparna

  I advise you to upgrade to 4.1 PowerCLI.

  If this is not possible use the attached script that works for versions pre-version 4.1 PowerCLI.

  ____________

  Blog: LucD notes

  Twitter: lucd22

• YouTube seems to be blocking the use of Firefox (MaskingAgent?) on 2015 / 01 / 08

  • YouTube seems to be blocking the use of Firefox on 2015-01-08, let me (ATTACH) a screenshot.
  • I see that the default search engine (alias "recipes) for Firefox Google/YouTube, Yahoo has recently changed.

  This is due to the extension of the masking Agent, sending deliberately incorrect sites on the browser you use. I don't know if the extension allows you to make an exception for youtube.com and ytimg.com in order to work around the problem. If this isn't the case, you may need to disable the extension.

  You can manage on the page extension modules. Either:

  • CTRL + SHIFT + a
  • "3-bar" menu button (or tools) > Add-ons

  In the left column, click Extensions. Then find Agent masking and check for that option button. This is also where you would turn it off.

  (Often a link appears above an extension disabled to restart Firefox. You can complete your work on the tab and click on the last step.)

  As far as I know, your default search engine is invisible to Web sites, so this probably isn't a problem. Or do you want to make a change here? This article has the steps: use the Firefox search bar.

• Why can I not use Kaspersky virtual keyboard?

  Any Firefox above 16 let me use the virtual keyboard from Kaspersky.

  He appears in the Addons Manager?
  If Yes, is it turned on?
  If this is not the case, see Kaspersky for an updated version of their Firefox addon.

• Nighthawk R8000 to Virgin Media Super Hub 2 connection problem.

  My R8000 does not connect to the hub super Virgin Media 1.0 Gbps. I have a line across the R8000 and 150 meg, I get only 96 Mbps.

  My LAN is defined as follows:

  Speed = 1.0 Gbps.

  I made the default settings and that it has not cured the problem.

  If I connect the VM 2 super hub directly to my PC I get 158,2 Mbps when the speed of local area periphery is 1.0 Gbps

  I'm on Windows 10

  When it is connected to the VM via Wifi hub, I get 157 Mbit/s on the % line GHz.

  Any suggestions on how to get this sort would be very usfulll

  OK I'll look into that. Thanks again.

• G505s and Virgin Super Hub

  Really pleased with this computer. Recently updated my internet hub to a Virgin Super Hub. I now can't get a wireless connection of wondows 8.0. When I switch to Windows 8.1 I get the message "unidentified network". I can connect via ethernet cable no problem.

  The wireless adapter is broadcom 802.11n network adapter

  Ipconfig confirms the hub is affecting an ip address for the G505s but will not allow connection internet. The hub admin confirms utility. Hub ping does not return anything.

  3 other laptops (including 2 Lenonovos on win 8.1) and 4 smartphones connect to internet via the new hub with no problems. I did the following: -.

  Restarted hub - many times

  Re-installed win 8 and 8.1 twice

  Follow-up of all win 8 and 8.1 updates

  Re-installed the driver Broadcom Wireless adapter - 3 times

  Tried the IP address physical address / gateway/SubnetMask etc.

  With the help of the Office of support from suppliers through various ipconfig and netsh commands

  Is this a problem with my network adapter?

  Jerry

  
  

• To configure a serial port using Max

  Hello

  I inherited the code that configures the serial port using the old serial code that does not allow the user to specify the term tank and turn on the tank of the term. Any ideas on how this is done with the old serial code? I also tried to use MAX to set the term tank and allow it, I am able to communicate with my device series with Max and I saved the changes when I was. So when I run Labview code, my serial code fails because the term tank is wrong and it is also not enabled.

  Everything that happens with the definition the term tank and allows ideas?

  What you do to the MAX to the extent where the configuration of the serial port have no impact on the LabVIEW program. (EDIT: which means that you can change the configuration in the LabVIEW code.)

  If you load the old code in a version of LabVIEW using VISAS for all the stuff of series then the screw would have been automatically replaced by shell screw that NEITHER created for the old code. Inside, they use just VISA. More than probably the old code use via digital port numbers. For example, in the library of \vi.lib\Instr\serial.llb of , you will see these shell screw Serial Port' writing' for example, calls the 'Open Serial Driver' VI which simply returns a VISA session. It then uses the Write VISA. So you can define characters of termination by obtaining the VISA of "Serial Driver Open" resource.

  Of course, the best solution is to rewrite the code using VISA directly. It will be much cleaner.