Ports VMK for nfs group

Similar Questions

• Ports vmk NFS considerations when you move a host of distributed 1 switch to another

  Hi everyone, I wonder if you can help with the following...

  I currently have a number of ESX host that accompany the dvswitch0 for connectivity management and NFS.  VM networks has already been migrated to new dvswitch. The following assumptions are correct?

  I need to remove a vmnic from the current dVS, so that I can create a standard vswitch and migrate vmk0 (network management) to it before removing the host of dvswitch0?

  When I did it and I delete the host of dvSwitch0, I lose connectivity for my NFS vmk? Or will they continue to work as I have the info ip configured locally on the ESXi host? I've recreated the PG for NFS on the new dvswitch bearing the same name and config like dvswitch that I want to spend

  If the connection is lost, I guess I need to migrate a vswitch standard before removing the vDS, identical to my management network of my NFS vmk. And then migrate them all using the wizard when I add my host to the new dwswitch

  If the connectivity will not be lost, I guess when I add the new dvswitch host and migrate my vmk0, the vmk NFS will appear in the PG on the new DVS as my exchanges were confiigured with the same name?

  Is that correct the above?

  Thanks in advance

  
  

  If the connectivity will not be lost, I guess when I add the new dvswitch host and migrate my vmk0, the vmk NFS will appear in the PG on the new DVS as my exchanges were confiigured with the same name?

  As long as there is a valid vmnic attached to your destination vSwitch and a group of ports on the VLAN, the migration of your NFS vmk interface will be successful.

  I suggest doing this kind of work, while the host is in maintenance mode; There will be a small window of time during the migration where the host loses connectivity to the NFS data store.

• Network for NFS

  Hello

  I have infrastructure as follows;

  2 welcome each containing 6 1Gig speed NIC each.

  A NAS storage with 4 NIC

  Two L2 Switches (managed HP).

  Planning to run it by the best recommendations and requirements, so that there should not be a SPOF any level.

  So keeping this in mind, we have designed to use ports on each server as follows:

  2 for the NFS storage, 2 for Production management and 2 others for vMotion on each server.

  A cable from each port configured for respective roles goes uplink switch1 and switch2, so if a switch goes down we still have the other switch support.

  Separated VLAN is configured by the switch to different types of traffic.

  My question as below;

  Should I team two ports on each vSS.If so that what should be the parameters for NETWORK adapters for the production, storage, and vMotion network grouping (keeping in mind cables going to switch uplink separated).

  Should I keep adapter in active-standby or active-active mode.

  I didn't think any specific settings to link pass that one cable by a single port is to go there and I don't have the choice of the channel of the ether or LACP.

  In addition, vmware license is essential and having therefore no possibility to use dynamic switches.

  Consider using 5.5.0.

  Also do you propose to use frames as well in the present.

  Kind regards

  Sushil

  Hello

  I suggest always you put management and vMotion on the same set of natachasery management and workloads. It makes no difference where they are subnet a perspective.  I also suggest to read the following:

  • The great debate VSwitch (old writings but still VERY there, let not the age fool you on this one)
  • VMware Virtual networking concepts
  • Networking for administrators of virtualization

  Who should you get.

  natachasery have no IP address in a vSphere environment, they act as a link between a physical and virtual switch. According to the way which you the trunk your VLAN Trunk ends pSwitch (external switch tagging) or the virtual switch (switch virtual tagging). Most people master their VLAN to the virtual switch.

  You want something like the following:

  pSwitch <->pNIC0 <->[ <->Portgroup vSwitch0] <->management (subnet1)

  pSwitch <->pNIC1 <->[ <->Portgroup vSwitch0] <->vMotion (subnet2)

  When switching between pNIC0 and pNIC1 management and vMotion end up on the same bear but when normally run that they remain separated. It is the recommended method. In this case you would master the VLAN to the vSwitch. I know some people who just do not use VLANs, but who use only separate subnets and it works as well.

  pSwitch <->pNIC2/pNIC3 <-> <->Portgroup vSwitch1 (s) <->of workloads (subnet1)

  If you use VLANs (except for vMotion) you're trunking to vSwitch1 (virtual switch tagging). If subnet1 is on the same vSwitch and the trunk is correct via pSwitch ports so he can talk to management on vSwitch0 effortlessly. Switches know how to route traffic to VLAN.

  pSwitch <->pNIC4/pNIC5 <->vSwitch2 <->Portgroup <->NFS (subnet3)

  Here we link pNIC4 and pNIC5 together or use them as a pair of failover for NFS on its own subnet / VLAN itself. This VLAN can end the pSwitch if you wish or terminate once again to the vSwitch.

  In this configuration you have 3 VLAN and 3 subnets (subnets use by VLAN are also recommended)... for example:

  VLAN100-> subnet1-> workload management

  VLAN200->-> vMOtion subnet2

  VLAN300->-> NFS subnet3

  Let the pSwitches any 'movement' of traffic for each VLAN. You need only a routing device if you want TO cross borders VLAN and there is absolutely no need to do it in this configuration.

  Best regards
  Edward L. Haletky
  VMware communities user moderator, VMware vExpert 2009, 2010, 2011,2012,2013,2014

  Author of the books ' VMWare ESX and ESXi in the business: Planning Server Virtualization Deployment, Copyright 2011 Pearson Education. ' Of VMware VSphere and Virtual Infrastructure Security: securing the virtual environment ', Copyright 2009 Pearson Education.

  Virtualization and Cloud Security Analyst: The Practice of virtualization, LLC - vSphere Upgrade Saga - virtualization security Table round Podcast

• Need new ports USB for Satellite Pro L450D

  Hello

  I ve tried to keep new ports usb for my Toshiba Satellite Pro L450D I ve called Toshiba and they said I have to put it in for repair, but the thing is - it's not is no longer in warranty so that I can t make and send to Toshiba for repair.

  for me would cost loads I ve asked Toshiba provide me for my laptop usb ports, but they won t so I would like to know where I can get these parts as one of my ports usb don t work because of my daughter in the first place to break them and the entire interior of the usb ports is broken.

  Help, please
  Thank you

  Hello

  At first, I must say that Toshiba service doesn t sell these small parts such as USB ports. USB ports are soldered to the motherboard.
  Where to get the new USB ports? Good question.

  I don t know where you MFL, but perhaps you should I use Google in your country and check if you can find some independent repairer for laptop and ask for help.
  I fear it won't be so easy to find new ports of m.

  What you can try is to buy defective mainboard in the hope of USB ports are OK and are trying to replace them.

• Can I set up a "permanent group" in contacts for SMS group or by e-mail?

  Can I set up a "permanent group" in contacts for SMS group or by e-mail?

  We need a lot more information to give you special help. Tell us step by step in detail what your actions are.

  Tell us a story

  -with a beginning, middle and end. We need to figure out what you know and that you have lived.

  If this problem is new, tell us what immediately preceded its appearance - add software, upgrade or update? New equipment?

  Quoted by of Apple  'how to write a good question.

  To help other members in answering your question, give as much detail as possible.

  • Include your name (peripheral) product and specifications such as the speed of the processor, memory and storage capacity. Please do not include your serial number, IMEI, MEID or any other personal information.
  • Provide the version of your operating system and the relevant applications numbers, e.g. "OS X 10.4.11" or "Safari 4.1.3.
  • Describe the problem and include all the Details on what seems to make it.
  • The list of troubleshooting steps you have already tried, or temporary corrections that you discovered.

  For a detailed 'coaching', please see usage tips , help us help you on these forums and wrote an effective communities of Apple Support question

  "Keep it short and Simple"-take your time... but be thorough - CCC

• Need help with the port forwarding for a XBox remote Streaming

  I have a router R6200v2 and need help with port forwarding.

  I came across this set of instructions for setting up stream port forwarding XBox remotely from anywhere

  http://kinkeadtech.com/2015/07/how-to-stream-Xbox-one-to-Windows-10-from-anywhere-with-Internet/

  I have no idea when it comes to such things and I want to make sure I do it correctly without messing up my existing home network.

  Port Forwarding and triggering Port pages setup look very different from what the guy uses. Can someone walk me through what I do to set up please?

  Hi @varxtis,

  You must enter them in the field for a start external Port and external completion Port. You will need to send individually except for the range of 49000-65000. The steps are as follows.

  1. create a Service name (it could be something else that you cannot use the same service name twice. Ex. XBOX1, XBOX2 and so forth.)

  2. Select the type of service (TCP, UDP or both)

  3 entry 5050 times a start external Port and external endpoints.

  4. Select the IP address of your XBOX.

  5. Select apply.

  6 do the same for other port numbers. To the beach, use 49000 for the external departure Port and for the external completion Port 65000.

  Kind regards

  Dexter

  The community team

• HP Compaq 6000 Pro AIO: PCI Serial Port driver for HP Compaq 6000 Pro

  Hello world

  I could get help to find driver serial port PCI for HP Compaq 6000 Pro all in one workstation. It has 8.1 Windows x 64 installed. The hardware IDS are

  PCI\VEN_8086 & DEV_2E17 & SUBSYS_1489103C & REV_03
  PCI\VEN_8086 & DEV_2E17 & SUBSYS_1489103C
  PCI\VEN_8086 & DEV_2E17 & CC_070002
  PCI\VEN_8086 & DEV_2E17 & CC_0700

  Thank you

  Vignesh

  Hello:

  You need this driver... Install manually if auto installation does not work.

  http://h20565.www2.HP.com/hpsc/SWD/public/detail?sp4ts.Oid=4210069&swItemId=vc_85050_1&swEnvOid=4059

  You can see on the partial copy and paste installation information file driver that the ID you have posted is supported by this driver.

  ; Drivers
  ;----------------------------------------------------------
  [Manufacturer]
  Intel % = Intel, NTamd64

  [Intel.NTamd64]
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E07 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E17 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E27 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E37 & CC_0700"
  % SRL_DeviceDesc % = ComPort, "PCI VEN_8086 & DEV_2E97 & CC_0700"

• I use a server DNS Server 2008 and need to transmit the DNS lookup on a Linux server that only allows you to Port 3128 for DNS.

  Hello

  I use a server DNS Server 2008 and need to transmit the DNS lookup on a Linux server that only allows you to Port 3128 for DNS.

  How can I configure my DNS server to use this port for shipments?

  Thanks for your replies

  Marcus

  Hello

  The question you posted would be better suited in the TechNet Forums. I would recommend posting your query in the TechNet Forums.
   
  http://social.technet.Microsoft.com/forums/en-us/winserverNIS/threads
   
  Here are a few Server DNS forwarders. Links for refrence,
   
  http://TechNet.Microsoft.com/en-us/library/cc754941.aspx
   
  http://TechNet.Microsoft.com/en-us/library/cc731991.aspx
   
  I hope this helps.

• combining individual photos in hotmail for a group of photos to email

  How to combine individual photos received in hotmail for a group of photos to pass on to third parties?

  Hello JonPaton,

  This thread has been created in the Microsoft answers Site Feedback forum. the Microsoft moderation team has moved this thread on the Forum ofNetworking, Mail and get online other/unknown.

  The question you have posted is related to Hitmail and would be better suited to the Windows Live community. Please visit the link below to find a community that will provide the support you want.
  http://windowslivehelp.com.

  Best regards

  Matthew_Ha

• on port 162 java.exe running. I tried to kill him with the command prodess k 1289. 1298 here is the process ID. but it comes back again. I need the port 162 for sending traps.

  original title: port162

  Hi, on port 162 there is a process called java.exe running. I tried to kill him with the command prodess k 1289. 1298 here is the process ID. but it comes back again. I need the port 162 for sending traps. I first removed java completely from my pc, but still there was this java.exe. in fact, there are two java.exe if I check in the running task manager. need help. I also ran antivirus as well as anti-malware software, but no difference.

  Hello

  I suggest you to visit these links and check if it helps:
  http://www.Java.com/en/download/uninstall.jsp
  http://Java.com/en/download/help/regkey_addremove.XML

  Have you tried to change the port to Java? See this link:

  http://www.Java.com/en/download/help/proxy_setup.XML

  It will be useful.

• How to put a heading for a group of controls without line below the title text?

  Hello

  Is it possible to write a heading for a group of controls and indicators made by "chiseled online", such as the chiseled line remain invisible under the title text and remain visible everywhere else? For example, the titles 'Printer', 'Range', 'Copies' and 'Zoom' in a Microsoft Word form in the PDF file attached. Note that there is no line under the title text and there is no text box surrounding the text of the title. I want to have that kind of title for the Group of controls and indicators in a GUI of my LabVIEW application.

  Any help will be appreciated.

  Thank you.

  Javed

  Any label you use as long as you COLOR IT CORECTLY. Use the background with transparent border color... just set the boxes of color as shown.

  

• How can you change a password on Vista for a group of net work at home

  How can you access the area to change the password for a group of net work at home? I'm unable to find had worked well but formatted Vista computer to make it faster. Now unable to find the box to change the password. Another computer on a network running 7.

  Hello

  What password are you talking?

  If it's regarding network sharing again the sharing.

  Maybe this can help.

  To get best results connect to each computer system screen and set all the computers to be on a bearing the same name of Working Group , while each computer has its own unique name.

  http://www.ezlan.NET/Win7/net_name.jpg

  Make sure that the software firewall, AV, or other security components allow free local traffic on all network computers. If you use the 3rd group of security, firewall native Vista/XP must be disabled, and the active firewall has adjusted to your network numbers IP on what is sometimes called the Zone of confidence (see part 3 firewall instructions

  General example, http://www.ezlan.net/faq.html#trusted
  Please Note that some 3rd party software firewall/AV/security costumes continue to block aspects of the Local traffic even it they are off (off). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic.

  If you end up with the 3rd party software uninstalled or disabled, make sure that Windows native firewall is active .

  Network Win 7 with another version of Windows as a work network (works very well if all computers are Win 7 also).

  In the center of the network, by clicking on the type of network opens the window to the right.

  Choose your network type. Note the check box at the bottom and check/uncheck depending on your needs.

  http://www.ezlan.NET/Win7/net_type.jpg

  Win 7 - http://windows.microsoft.com/en-us/windows7/Networking-home-computers-running-different-versions-of-Windows

  Win 7 network sharing folder specific work - http://www.onecomputerguy.com/windows7/windows7_sharing.htm

  Vista file and printer sharing - http://technet.microsoft.com/en-us/library/bb727037.aspx

  When you have finished the configuration of the system, it is recommended to restart everything the router and all computers involved.

  -------------

  If you have permission and security issues with Vista/Win7, check the following settings.

  Point to a folder that wants to share do right click and choose Properties.

  In the properties

  Click on the Security tab shown in the bellows of the photo on the right) and verify that users and their permissions (see photo below Centre and left) are configured correctly. Then do the same for the authorization tab.

  This screen shot is to Win 7, Vista menus are similar.

  http://www.ezlan.NET/Win7/permission-security.jpg

  The Security Panel and the authorization Panel, you need to highlight each user/group and consider that the authorization controls are verified correctly.

  When everything is OK, restart the network (router and computer).

  * Note . The groups and users listed in the screen-shoot are just an example. Your list will focus on how your system is configured.

  ** Note . All the users who are allowed to share need to have an account onall computers that they are allowed to connect to.

  Everyone is an account, that means a group of all users who already have an account now as users. It is available to avoid the need to configure permission for each on its own, it does not mean all those who feel that they would like to connect.

• How it works for objectChoice group "FOCUS_CHANGED".

  Hi all

  can someone tell me how FOCUS_CHANGED works for the group object of choice when we change our focus in the drop-down window?

  actully I use:

  {public focusChanged Sub (field field, int eventType)

  If (eventType == FOCUS_CHANGED) {}
  System.out.println ("FOCUS_CHANGED");
  } else if(eventType == FOCUS_GAINED) {}
  System.out.println ("FOCUS_GAINED");
  } else if(eventType == FOCUS_LOST) {}
  System.out.println ("FOCUS_LOST");
  }

  }

  It nevers print "FOCUS_CHANGED", but it works for the FOCUS_GAINED and the FOCUS_LOST.

  Please help me.

  Its urgency.

  Thank you

  Ashutosh

  Well you're right, it doesn't have the fire for me either. You can use "FieldChangeListener" it will be server your purpose.

• BlackBerry smartphones looking for a group sms application

  I'm looking for a group sms application that will allow me to assign a number of contacts to a group, so when I need to send an sms to all these contacts, I need to do is select the group instead of selecting each contact individually. also, it would be nice if this app can aloow to synchronize me with outlook and my emails. thanx

  I know that you can create a group of contacts in the address book. Try and see if you can mass-SMS to that group.

• When I use the Client for NFS provided by Windows 7, I'm unable to connect. The "mount \\ip address\share Z:" command fails with the error code "the path not found network".

  Identification of customer's Windows 7 NFS UID GID information

  I am trying to connect to the Windows 7 Client NFS on a server running on a computer (VxWorks) NFS.  I am able to properly connect Client NFS software by a 3rd party on the NFS server.  However, when I use the Client for NFS provided by Windows 7, I am unable to connect.  The \\ip address\share Z: mount"command fails with the error code"the path not found network ".  I can't do a ping of the computer running the NFS server.

  The NFS Client operating system: Windows 7 Ultimate, 64-bit

  Data captured by Wireshark

  MOUNT V1 EXPORT call 3rd party client
  Identification information Flavor: AUTH_UNIX (1)
  Length: 32
  Stamp: 0xc7065970

  Machine name: PC
  UID: 1000
  GID: 1000

  MOUNT V1 EXPORT appeal of the NFS client
  Identification information Flavor: AUTH_NULL (0)
  Length: 0

  It seems that the credentials of NFS Client are not correct.  How can I change the flavor of AUTH_UNIX and the UID and GID to 1000?

  Hello VDAEMP,

  As Eddie and Sudarshan has said, the Microsoft Answers community focuses on issues and problems related to the consumer environment. Please join the public IT pro TechNet forums below:
  TechNet - Windows Server
   
  Thank you