Positive reviews from Bionic roll

Similar Questions

• A positive review on the V3 771 g 9809

  Many come to forum questions and receive help. I still want to give positive results on the laptop that I chose.

  Model: Aspire V3 - 771 g-9809

  First of all. It is a portable large Due the screen 17.3 ". She is described as a replacement of officeor mobile desktop. Newer models have been improved with changes to the kernel and the bowels (units pre-installed windows 8).

  First of all, I need to say that the current reviews and benchmarks there are no where near reliable. The sad truth is tomshardware and many sites did not include unity that they received, the fact there bi - GPU, and when they compared the games, clearly, they have therefore, using GPU and not the default HD4000 energy saving GT650m. I assure you, run 3dmark in all 3 formats and GPU will amaze you.

  GAMES:

  The unit uses 2 GPU. The HD4000 and the GT650m. By default (with the standard version drivers), the device will use the HD4000. IF you have the latest Nvidia drivers for it, some games are in the profile list of games, and those who will move to the use of the GT650m. You can add programs to the list, or force the laptop to use the GT650m for the high end games.

  I installed Battlefield 3 THE on the laptop. He ran flawlessly on the spot at the appropriate resolution. Locked capsule rate of 60 frames per second, with a few depressions in the places of strong thickness, but nothing below smooth frame rates. The only downside is the loading time can be long due to the upper part of the Tower standard RPM hard disk. However, if running off a Solid State drive secondary, load times are quick (this game is infamous for the slow charge).

  I am an Alpha tester for Final Fantasy XIV Online: A Kingdom Reborn. He is the alpha of the game again, which by the way, is a lot better now. The laptop the big plays on the spot with all the effects to the top. The downside is that alpha can't stand the odd screen resolution, so it assigns 720 p. However by the HDMI it plays fine on a 1080 p HDTV. Time of loading between the areas are a few seconds.

  Amular Kindoms: Reckoning - Mount. The game is played flawlessly at a constant speed. Loading times are not as long. It supports the resolution of monitors and looks amazing. (use an Xbox controller for this game for ease of use).

  DISPLAY:

  There are units that short coming with a resolution of 1600 X 900 on the unit, but higher supported via HDMI and VGA. However it is far around that if you know where to look, but it makes it a little less visible window 8. The screen is bright. You have total control over the brightness, contrast, color saturation, gamma and other entities via the Intel Board, which controls the GT650m (equivalent to a GTX 640) same settings. The default brightness is too high. You can type up to-3.

  SOUND:

  Output is good, but the small speakers, like many high knees, don't you not bass. Just for video chats and listening to low level. The screen surround is good for headphone Virtualization or use a USB surround headset. I wouldn't mind better speakers built in.

  KEYBOARD:

  The fact he has a num pad, is great. Many controls feature keys. It's not backlit, but that's ok. There is however no lights for NumLock and caps lock shift which he should have. With windows 8 it let's you know when caps lock shift is on.

  FEATURES OF ACER:

  Acer is known for putting things added on their devices. However, they actually use. We can not all use clear.fi so that you can disable.

  Acer device Fast Lane, is very convenient. It's in your quickbar in airplane mode, bluetooth, press the key and you said it if your shift caps lock is enabled or disabled (so there for an app for the lids and num lock on screen is simple).

  The power button icon: It is located on the bar in desktop mode as well. For fast Lock, sleep, Hibernate, restart, and shutdown.

  All the standard Acer apps, backup soft, is also included.

  I love this laptop. It's fast. Play games well. Has a nice big screen. A lot of features. Extra slot Bay for adding a second drive or Solid State Drive. The USB 3.0 ports are blue on the left side, USB 2.0 black on the right side. That way you know which is which.

  If you are not sure, the cost of the laptop with the CPU and GPU power makes good worth. Even more so for students who need to work on classes, but who want to play as well.

  Thanks Diorio

  You made my Christmas... IM my opinion, it is one of the best review ever! Great mate!

  Kind regards

  FReeZA

• Problem of Position of from mouse

  With 7 slides in my Captivate project, I added about 5 points of mouse movement to the overall project. The first mouse point added allows me to move the start and end of the mouse position. Unfortunately, the remaining elements of the mouse do not have the Red mouse from position the handle, so I can't move the starting position! I tried for all settings, closing and re-opening the project, even reboot the PC, but no luck. I tried a few searches on this, but very little is out there.
  Any help would be appreciated: o)

  Hi Beaker23 and welcome to our community

  As you have seen, you can only configure the starting point for the mouse on the first slide, where the movement of the mouse starts.

  Look at the following tutorial. Click here to see the tutorial

  If you need to adjust the starting position of slides, adjust you when the mouse has stopped on the previous slide. To do this is to duplicate the slide, set up the calendar for the new slide duration minimum (.1 seconds) and adjust the position on the new slide.

  See you soon... Rick

• How to remove easily several photos from camera roll

  Hello, I want to delete easily a lot of photos on my camera, iPhone 6, is there a simple way without selecting each other?

  Thanks Dianab188

  http://www.iphonefaq.org/archives/974282

• Why the text fields are not shown in the exact position where I place, being in a position different from the design view and preview?

  Enclosed is the difference in preview mode and Design Mode.

  Please note that I noticed the same phenomenon occurs on the "IRINA" template that I downloaded for use in training.

  

  Well, what you are is the correct behavior. The image is scaling due to the width of the browser. This is normal because the text does not meet the resizing (yet). You should be able to fix this in the next version of Muse. Or you can join the public beta version now and try it.

• measure display to the left of position instead from above

  Can someone tell me how to move items measure to the left of the measure, so it appears as follows on the report
  
  number of people 1520
  
  Instead of
  
  number of people
  1523
  
  I chose the third option button in the PivotTable to "column title display" but he has not made a difference. I intend to create a report with the title headings to the left and on the right counts and were only able to manage it using dummy columns. There must be an easier way to do this :(
  
  Help, please.

  Hello
  move the option of 'Measures' in the columns PivotTable beside lines section

  Thank you
  Saichand.v

• Pavilion x 2 detachable 10-n123: cable USB of Type C on Pavilion X 2 detachable

  I bought a cable USB of Type C on Amazon to use with my Pavilion x 2. When I plugged the end of type A into a charger that I and the end of Type C in the 2 x led light white next to the USB port on the x 2 briefly flashed on and off.  When I plugged the Type a end on my desktop and the end of Type C in the 2 x I got the same result.  I tried another cable of Type C with the same result.  In one of my essays (I think it was plug the charger with the x 2 running) I ended up getting a message on the x 2 on the corruption of the BIOS and I had to go through a process using a Bitlocker code to restore the x 2 in working condition.

  The 2 x charge very well with all cable/adapter shipped with the x 2.  I want just an alternative.  I don't want to depend on a single cable.

  Two cables I've tried has received very positive reviews from other users on Amazon.

  The x 2 only works with the cables of Type C from HP?  Or something is wrong with my x 2?

  I realize that I just wanted to know if she would still charge after that.

  Also, in the Amazon reviews, there are lot of people having a similar trouble their features of loading with the version cable issues. It seems that there are compliance issues at the present time, manufacturers are still sorting.

  You can have one of these bad cables?

  Cable questions seems to replace the cables at the request of customers.

  Other than that, I can't tell you, it would be a total guess. I'm sorry.

• Unable to connect wireless Bluetooth keyboard with the iMac

  After researching for a numeric keypad for my iMac (OS X version 10.6.4), I decided to get a keypad wireless Microsoft due to many positive reviews from Mac users. I tried to connect the camera today: 1) turned on the numeric keypad) 2 Mac software came on and recognized 'Microsoft BlueTooth number Pad' 3) a password has been generated) 4 ' synchronization attempt failed"I tried several times with the same result.  I realize that I am a Mac user, but I would give it a try since the system of thought is a Microsoft product. Any help would be appreciated because I would REALLY use it!

  Hi mfranken.

  As you have is on Mac operating systems, I suggest that you contact Apple for assistance.

  http://www.Apple.com/support/osFamily/

  I hope this helps!

  Halima S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• How to download files from images on a PC?

  I'm trying to figure out how to download image files in bulk from my iPhone.  Photos are sent to me by members of the family using iPhones.  I don't know where they're going, but image files appear on my iPhone.  I just want to download these files on my PC.  I know how to send photos unique to me by email, but it's too labor intensive and time consuming.  Is it possible to send files from my iPhone photo to my PC?  I read all articles, FAQ Apple and tried to click on all the sharing options, but have had no success.

  iOS 9.2.1.  PC running Windows 7.  A lot of processor, RAM, etc.

  It works easy with photos from camera roll

  If I were you I would try using dropbox or something on both devices

• How can I transfer photos from film on iPad mini iMac

  I have pictures on my camera iPad mini roll which do not seem to have been downloaded on my iMac.

  I often will have pictures from an Sd Card (with adapters) or wifi from my camera to my iPad but not, when I got home, of course to my iMac.

  I need to make room on my iPad how do I transfer it to my iMac.  (I'm still under Maverick, I know!    iPad ISO9.2.1 running)

  I do not use the cloud to store my photos just transfer them via the photo stream.

  The photos are not all on my photo gallery. The photos will go back two years. !

  I recently activated photo stream (October, last year) photos to transfer photos from my iMac iPhoto events if some are OK. I used the info forum to delete several of these photos.

  To check if I remove a photo from my roll of picture on my iPad, it is not deleted from my iMac, correct?  and according to the original question, I need to transfer photos to my iMac.

  IF you have photos that have not been transferred to the Mac because they predate photo stream, you can import them from the film by connecting the iPad to Mac with the cable and launch iPhoto or Image Capture. Your iPad must appears as a device in the left of either of the two apps bar and you will be able to import photos and then delete them from the iPad if you want to do.

  hazel170 wrote:

  To check if I remove a photo from my roll of picture on my iPad, it is not deleted from my iMac, correct?

  As long as the photos have been imported to the Mac, you can delete them from the camera without them being removed from the Mac.

  .. nothing wrong with still run Mavericks if you are uncomfortable with him and it meets your needs. I'm still in Yosemite with no desire to go straight, to El Capitan

• How can I transfer photos labelled "on my computer" from my iPhone to my PC?

  Hi guys.  I have 450 photos that have been synced to my 5s when I upgraded to 4S.  I am trying to transfer these photos - now named ' my computer' - on my PC.  I tried to do in iTunes, however, the folder does not appear as a choice of synchronization.  All I get is Camera Roll ControlCenter3 and images - which have zero points.  When I go into my computer, I have only my photos from camera roll in the DCIM folder.

  Any ideas?  Thank you very much in advance.

  Synchronization of photos is a way - computer to iPhone.

  Your photos have come from your computer in the first place, so they should still be there, and you should always have a backup of your computer.

  The iPhone is not a backup/storage device.

• 2740 - Dead Zones touchscreen - blind spots keep alternating from consecutive cycles of power

  Hello

  I return my 2740 two days and since I am faced with the question of areas inaccessible to the corners of the touch screen.

  To explain further, I'm numbering of the corners as 1,2,3,4 from the top left and go elsewhere (with the display in normal mode for portable computer with keyboard open).

  I'm dead in 3 corners (2,3 and 4) zones. I can drag and drop the slider to one of those corners, I can do the selection rectangle on the desktop windows (but of course from a position away from these corners, when even it means that they are not totally dead), but I can't save any tap (i.e.. clique) on these corners for about 1 to 1.5 cm. considering that, in the corner 1 works perfectly.

  What makes this problem even more strange is that these dead zones alternating custody after consecutive/recovery stops after sleep, that is.

  After stop/standby #1: blind spots are # 2,3,4

  After stop/standby #2: blind spot is no. 1

  After stop/standby #3: blind spots are # 2,3,4

  After stop/standby #4: blind spot is no. 1

  After stop/standby #5: blind spots are # 2,3,4

  After stop/standby #6: blind spot is no. 1

  And a normal restart has no effect on blind spots, there must be a stop or a sleep-CV. Given that each of the corners work, but not all together, makes me very doubtful that this could be a hardware fault.

  I already tried the following hotfixes mentioned by people facing similar problems with their 2740:

  1. different "Wacom Digitizer Driver" published by HP, April 30, 2010, June 23, 2010 and November 22, 2010, respectively.

  2 reloaded Windows 7 Professional 64 bit from scratch and I tried all kinds of drivers, even those of Wacom Web site.

  3. power cycled my unit, that is. has out the battery and ran my unit from the mains without the battery.

  Any information would be extremely useful and appreciated. Others who are facing similar issues well to respond to this thread as well.

  Thank you

  Mrinal

  For reference:

  Corner #1: Top-left

  Corner #2: Top-right

  Corner #3: Down-right

  Corner #4: Left-bottom

  I was able to completely solve the problem of dead with a simple update zone

  For convinience other users faced with similar problems, I'm reposting the fix as suggested by in4mer. If you encounter problems with these steps, please browse the thread started by in4mer, to:
  Indoor/outdoor touch screen and the Pen Firmware update

  Please download and install the following ' Indoor/outdoor Touch Panel and Pen Firmware Update', by using the following link:
  HP EliteBook 2740 Tablet PC - interior/exterior touch screen and stylus updated Firmware - HP Business Support Center

  Don't forget to read the 'Installation Instructions'. If the executable provided by HP is unable to create the bootable USB key, then follow the next procedure.

  Step 1. Creating a USB bootable BACK by following the instructions at:
  How to format a USB stick

  Note: You don't need additional utilities, so no need to copy the files from the Win98 startup disk manually on the USB key, just leave him with the 3 files illustrated in the screenshot of last second.

  Step 2 Copy all the files in the folder "Rompaq" on USB. This folder can be located either in the directory "C:\SWSetup\sp49201", or anywhere where the executable updates downloaded to date (i.e. sp49201.exe) excerpt from its content. Or, you can just use 7 - zip to extract the content of sp49201.exe and to access the folder "Rompaq.

  Note: You may need to activate the options "Show hidden files" and "Visualize protected system files", which is located under the 'View' tab in 'Folder Options', which can be opened from the menu item "tools > Folder Options ' in 'Windows Explorer '. In ' Vista/Windows 7' press the 'Alt' key to make the menu bar in 'Windows Explorer' visible.

  Step 3 Start your computer using the USB. After the comand prompt appears, type "SAM. BEATS", and then press on enter if the value of your monitor starts with"DRY"or type"HYDIS. BEATS"and press ENTER if the value of your monitor starts with"BEP ".

  Note: Boot Menu options are available by pressing the key "F9" as soon as the computer starts to boot and HP logo appears.

  Note: he showed both old and new firmware as even by updating the firmware on my machine. But he still solves the problem.

• Police base / positioning of the text of point vs box

  For some stupid reason too long to address here, I place some point text in the same place, as it would be placed if it was in text box.

  However, it appears in the text box is positioned compared to the 'first line' of the police, while the sharp text is positioned (anchored) from the baseline of the text, see the next with the same position sample model:

  

  What I've done here is just first create "mypoint" by clicking on (0,0) and paste the text ' "(which contains characters that show the level of reference and full height also), and create the text box"mybox"set by draw a text box to (0,0) to (1 000 100) and paste the same text and by changing the colors to make them recognizable.

  I then just added a rule to y = 100, added an adjustment layer and it value parent of these two layers, then shift the position of the adjustment layer - 100 so I can see what is happening.

  Now the question is, how to calculate what "mypoint" position would be to align on the same alignment of Y-position that the text "mybox" is?

  Just for the inspection of a few things:

  

  Looking at the returned rectangles sourceRectAtTime() I get something in the general direction of the following, but he is not quite right:

  

  model var = app.project.activeItem;

  var b = comp.layer ("mybox");

  var p = comp.layer ("mypoint");

  BR var = p.sourceRectAtTime (0, false);

  PR var = b.sourceRectAtTime (0, false);

  var text = p.sourceText.value; copy settings

  var t2 = comp.layers.addText (text);

  text = t2.sourceText.value;

  text.applyColor = true;

  text.fillColor = [0,1,1]; cyan to differentiate

  T2.sourceText.SetValue (Text);

  T2. Name = "myotherpoint";

  T2.parent = comp.layer("adjust-y");

  T2.position.SetValue ([0, 0]); gives the same position as "mypoint".

  T2.position.SetValue ([0, br.top - pr.top]) / / slightly off

  T2.position.SetValue ([0, text.fontSize]) / / No, too low

  Is it a reasonable way of calculation and this... ?

  I tried to add a point text and to match a text box, with a code similar to yours, and it works.

  However I have no parent the text point to layer "settle there" (because you said nothing on the subject), but directly in the text of the box.

  Start-ups can come from your transformation parameters to "settle there" layer. Maybe reset?

  I used this code:

  var comp = app.project.activeItem;
  var b = comp.layer("mybox");
  var br = b.sourceRectAtTime(0, false);
  
  var p = comp.layers.addText(b.text.sourceText.value.text);
  p.name = "mypoint";
  // make same doc specs (skipped)
  var pr = p.sourceRectAtTime(0, false);
  
  // parent, then set relative position
  p.parent = b;
  p.transform.position.setValue([br.left-pr.left, br.top-pr.top, 0]);
  

  Xavier

  Edit: just realized that 'set the y' is on your screen, and it is the parent of all the layers...

  I don't have a lot of time to understand why your code does not work, but if you parent the point of the box instead of the box parent, then it should work.

• Serious accidents with control of the expression spacing based on z-position of the layer

  I have massive crashes when you use this script expression below. I have just a text layer where I control the depandend letter-spacing of the current z position. From z = 0 to-500 (directly in front of the camera), the values are transformed by easyOut() from 0-10. So far, that's all.

  Now when I duplicate this line of text several times and start to change its position, then the accident happens. Text layers more I have the sooner the crash. This occurs when the edition therefore not made involved. In the preview is the applied standard rendering engine.

  Unfortunately, there is no specific error message - it indicates just that AFX no longer works and is now closed.

  My system features:

  I have 8 GB of RAM and 10 GB disk cache. That should be enough for a text flying around.

  I use the latest Version of CC of AFX 2015.1 13.6.1.6 running on Windows Ultrabook (Lenovo Yoga 1) 8.1. No CUDA detected so the preview is rendered by the CPU.

  Anyone has an idea why this happens? Help is very appreciated.

  max_spacing = 10;
  z_position = transform.position[2];
  var new_spacing = easeOut(z_position, -500, 0, max_spacing, 0);
  text.animator("Animator 1").property.trackingAmount = new_spacing;
  

  This is my test scene:

  http://Augenpulver-design.de/Exchange/tmp/AFX_Expression_Crash_Scene.zip

  You create a hole of logic by referencing the layer itself probably. Should not happen, then I would call it a bug. Probably to do with flaky matrix code also used to smack and a few other things. Try to use a Null value and parent the text to it. This would work much better.

  Mylenium

• VCP 4.1 review before training

  Hi all

  I intend to pass the review of VCP 4.1 before participating in the mandatory classroom training. That's because my training is scheduled for next month, and I already have the hands on experience with vSphere and want to save time by giving the review from the outset.

  VMWare allows / she acknowledges this approach.

  Thanks in advance,

  Kind regards

  Shane

  Hi Robert, yes VMware allow you to do. I guess you've studied according to the examination plan and the official documentation for vSphere 4? You will be asked some very specific questions to the review, I have many VCP4 links and information on my blog - http://vmwaretraining.blogspot.com

  Good luck

  Scott.

  -