PPTP and ASA 5505

I have a computer that must reach a server remote pptp, but receives an error that remote server is inaccessible. I have no restrictions on the inside interface, I'm guessing that something should be added on the external interface?

The asa is 8.2, ASDM 6.2.

Thank you

Try adding inspect pptp at inspection_default global_policy/class policy-map

Tags: Cisco Security

Similar Questions

VPN between 878 router and ASA 5505

Hello world

I struggled for a few days now to get a VPN connection works.

The situation

Two offices needs to be connected to eachother with a VPN. The two parties have a WAN connection.

The tunnel between locations rises very well but the communication fails in almost any way.

The host cannot ping each other and also the inside of the router and ASA pings fail.

The only ping works is from inside Site2 to the inside interface of the router side 1 (192.168.1.100 to 192.168.0.250)

NAT works very well on both sites behind the router / asa.

I think I'm doing something wrong with the roads or access lists but after 7 days, many refills, restores, driving from one end of the State to the other to reset stupid moves break and resolder my cable from the console and things completely with default start for 10 times, I'm through, I honestly don't know where to look for more...

Tech Specs:

Site1: has a cable modem that gives a WAN IP with DHCP address

This modem connects to the Cisco 878 (Fastethernet0) router

The router acts as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office

Site2: has a cable-modem/router (Cisco 3925), which made the NAT, this modem/router gives an IP private class-C (192.168.178.x)

This modem/router connects to a Cisco ASA 5505 (Fastethernet0)

The ASA also server as a DHCP server and NAT gateway for the office and offers vpn connectivity to the other office.

Online, it looks like this:

Office 1--> Cisco878--> WAN Cloud<---cablemodemrouter><--- asa5505=""><--- office="">

IP address ranges:

Office 1

Network 192.168.0.0

Subnet mask 255.255.255.0

Gateway 192.168.0.250

IP WAN XXXX

Office 2

Network 192.168.1.0

Subnetmak 255.255.255.0

Gateway 192.168.1.1

IP WAN XXXX

On the location of office 2, there is a NAT between ASA and WAN router. between 192.168.178.x 255.255.255.0

The modemrouter is a Cisco 3925, on which IPSEC passthrough is enabled.

Configs:

Site 1:

CISCO 878 router

Site 2

ASA 5505

I hope someone has a chance to look through my config and tell me what I did wrong this week

Even if you can not help me but still read here: Thank YOU!

(As my problem has been resolved, I removed the configs of this post. If for any reason, you want to work for these devices configuration, please send me a PM)

Post edited by: taaa lijf - reason: problem solved, removed configs and stuff private for obvious reasons ;)

Hello

Ping client customer site 1 site2 and make sh crypto isakmp his and sh crypto ipsec his on the router.

If sh crypto isakmp gives QM_Idle and ping fails and you have no package in the HS cypto ipsec his and then do a debug crypto ipsec

If sh crypto isakmp gives MM_NoState can do a debug crypto isakmp

One note however, you should have ip addresses static at least on the side, initiating the tunnel, otherwise it will not work when ip address changes.

Kind regards.

Alain.

Remote IPSec VPN - client Windows 7 and ASA 5505

Hello

I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.

Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.

In the log, I see the warnings of this type:

TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)

I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.

Thank you for your help.

Petar Koraca

That's what you would have needed on versions 8.3 and earlier versions:

permit same-security-traffic intra-interface

Global 1 interface (outside)

NAT (outside) 1 192.168.150.0 255.255.255.0

However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)

permit same-security-traffic intra-interface

network of the NETWORK_OBJ_192.168.150.0_24 object

dynamic NAT interface (outdoors, outdoor)

Give it a shot and let me know how it goes.

Need help! ASA 5505 not PPTP passthrough to the Server internal

Hello:

Recently, I add a new Cisco ASA 5505 like Firewall of the company network. I found that the PPTP authentication has not obtained through internal Microsoft Server. Any help and answer are appriciated.

Please see my setup as below. Thank you!

ASA Version 8.4 (3)
!
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
switchport access vlan 2
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 172.29.8.254 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 177.164.222.140 255.255.255.248
!
passive FTP mode
clock timezone GMT 0
DNS server-group DefaultDNS
domain ABCtech.com
permit same-security-traffic inter-interface
network obj_any object
172.29.8.0 subnet 255.255.255.0
service object RDP
source eq 3389 tcp service
Orange network object
Home 172.29.8.151
network of the WAN_173_164_222_138 object
Home 177.164.222.138
SMTP service object
tcp source eq smtp service
service object PPTP
tcp source eq pptp service
service of the JT_WWW object
tcp source eq www service
service of the JT_HTTPS object
tcp source eq https service
network obj_lex object
172.29.88.0 subnet 255.255.255.0
network of offices of Lexington Description
network obj_HQ object
172.29.8.0 subnet 255.255.255.0
guava network object
Home 172.29.8.3
service object L2TP
Service udp source 1701 eq
Standard access list VPN_Tunnel_User allow 172.29.8.0 255.255.255.0
Standard access list VPN_Tunnel_User allow 172.29.88.0 255.255.255.0
inside_access_in list extended access permit icmp any one
inside_access_in tcp extended access list deny any any eq 135
inside_access_in tcp extended access list refuse any eq 135 everything
inside_access_in list extended access deny udp any what eq 135 everything
inside_access_in list extended access deny udp any any eq 135
inside_access_in tcp extended access list deny any any eq 1591
inside_access_in tcp extended access list refuse any eq 1591 everything
inside_access_in list extended access deny udp any eq which 1591 everything
inside_access_in list extended access deny udp any any eq 1591
inside_access_in tcp extended access list deny any any eq 1214
inside_access_in tcp extended access list refuse any eq 1214 all
inside_access_in list extended access deny udp any any eq 1214
inside_access_in list extended access deny udp any what eq 1214 all
inside_access_in of access allowed any ip an extended list
inside_access_in list extended access permit tcp any any eq www
inside_access_in list extended access permit tcp any eq www everything
outside_access_in list extended access permit icmp any one
outside_access_in list extended access permit tcp any host 177.164.222.138 eq 3389
outside_access_in list extended access permit tcp any host 177.164.222.138 eq smtp
outside_access_in list extended access permit tcp any host 177.164.222.138 eq pptp
outside_access_in list extended access permit tcp any host 177.164.222.138 eq www
outside_access_in list extended access permit tcp any host 177.164.222.138 eq https
outside_access_in list extended access allowed grateful if any host 177.164.222.138
outside_access_in list extended access permit udp any host 177.164.222.138 eq 1701
outside_access_in of access allowed any ip an extended list
inside_access_out list extended access permit icmp any one
inside_access_out of access allowed any ip an extended list
access extensive list ip 172.29.8.0 outside_cryptomap allow 255.255.255.0 172.29.88.0 255.255.255.0
inside_in list extended access permit icmp any one
inside_in of access allowed any ip an extended list
inside_in list extended access udp allowed any any eq isakmp
inside_in list extended access udp allowed any isakmp eq everything
inside_in list extended access udp allowed a whole
inside_in list extended access permitted tcp a whole
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
local pool ABC_HQVPN_DHCP 172.29.8.210 - 172.29.8.230 255.255.255.0 IP mask
ICMP unreachable rate-limit 1 burst-size 1
enable ASDM history
ARP timeout 14400
NAT static orange interface (inside, outside) source RDP RDP service
NAT (inside, outside) source obj_HQ destination obj_HQ static static obj_lex obj_
Lex-route search
NAT guava Shared source (internal, external) WAN_173_164_222_138 service JT_WWW JT_WWW
NAT guava Shared source (internal, external) WAN_173_164_222_138 service JT_HTTPS JT_HTTPS
NAT guava Shared source (internal, external) WAN_173_164_222_138 service RDP RDP
NAT guava Shared source (internal, external) WAN_173_164_222_138 SMTP SMTP service
NAT guava Shared source (internal, external) WAN_173_164_222_138 PPTP PPTP service
NAT guava Shared source (internal, external) WAN_173_164_222_138 service L2TP L2TP
!
network obj_any object
NAT dynamic interface (indoor, outdoor)
inside_in access to the interface inside group
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 177.164.222.142 1
Route inside 172.29.168.0 255.255.255.0 172.29.8.253 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
AAA-server protocol nt guava
AAA-server host 172.29.8.3 guava (inside)
Timeout 15
guava auth - NT domain controller
identity of the user by default-domain LOCAL
Enable http server
http 172.29.8.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set esp-3des esp-md5-hmac Remote_VPN_Set ikev1
Crypto ipsec transform-set esp-3des esp-md5-hmac Remote_vpn_set ikev1
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto-map Dynamics 20 ikev1 transform-set Remote_VPN_Set set outside_dyn_map
Crypto-map dynamic outside_dyn_map 20 the value reverse-road
card crypto outside_map 1 match address outside_cryptomap
peer set card crypto outside_map 1 173.190.123.138
card crypto outside_map 1 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5
ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA'RE
P-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 1 set ikev2 AES256 AES192 AES 3DES ipsec-proposal OF
map outside_map 65535-isakmp ipsec crypto dynamic outside_dyn_map
outside_map interface card crypto outside
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev2 allow outside
Crypto ikev1 allow outside
IKEv1 crypto policy 1
preshared authentication
3des encryption
sha hash
Group 2
life 43200
IKEv1 crypto policy 10
authentication crack
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 20
authentication rsa - sig
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 40
authentication crack
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 50
authentication rsa - sig
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 60
preshared authentication
aes-192 encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 70
authentication crack
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 80
authentication rsa - sig
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 90
preshared authentication
aes encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 100
authentication crack
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 110
authentication rsa - sig
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 130
authentication crack
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 140
authentication rsa - sig
the Encryption
sha hash
Group 2
life 86400
IKEv1 crypto policy 150
preshared authentication
the Encryption
sha hash
Group 2
life 86400
Telnet 192.168.1.0 255.255.255.0 inside
Telnet 172.29.8.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0

dhcpd auto_config off vpnclient-wins-override
!
dhcprelay Server 172.29.8.3 on the inside
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
internal ABCtech_VPN group strategy
attributes of Group Policy ABCtech_VPN
value of server DNS 172.29.8.3
Ikev1 VPN-tunnel-Protocol
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list VPN_Tunnel_User
value by default-field ABCtech.local
internal GroupPolicy_10.8.8.1 group strategy
attributes of Group Policy GroupPolicy_10.8.8.1
VPN-tunnel-Protocol ikev1, ikev2
name of user who encrypted password eicyrfJBrqOaxQvS
tunnel-group 10.8.8.1 type ipsec-l2l
tunnel-group 10.8.8.1 General-attributes
Group - default policy - GroupPolicy_10.8.8.1
IPSec-attributes tunnel-group 10.8.8.1
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
tunnel-group ABCtech type remote access
attributes global-tunnel-group ABCtech
address ABC_HQVPN_DHCP pool
authentication-server-group guava
Group Policy - by default-ABCtech_VPN
IPSec-attributes tunnel-group ABCtech
IKEv1 pre-shared-key *.
tunnel-group 173.190.123.138 type ipsec-l2l
tunnel-group 173.190.123.138 General-attributes
Group - default policy - GroupPolicy_10.8.8.1
IPSec-attributes tunnel-group 173.190.123.138
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
remotely IKEv2 authentication certificate
pre-shared-key authentication local IKEv2 *.
!
class-map inspection_default
match default-inspection-traffic
!
!
Policy-map global_policy
class inspection_default
inspect the pptp
inspect the ftp
inspect the netbios
!
172.29.8.3 SMTP server
context of prompt hostname
no remote anonymous reporting call
Cryptochecksum:6a26676668b742900360f924b4bc80de
: end

Hello Wayne,

The first thing I noticed

In the ACL you are pointing to the broad public while it should be to the private sector (YOU HAVE A PERMIT IP ANY ANY to the end, so it's not bad. FYI, if you decide to take this one any allowed ip address then you should point to private servers ip addresses)

Now, the policy where the PPTP inspection, etc., will be used is not applied to any service-policy so add:

global service-policy global_policy

Don't forget not just for a PPTP connection to get established we should see 2 things:

-Trading is done on the TCP 1723 port and then traded on Appreciate data packets.

Follow my blog for more information on this topic:

http://laguiadelnetworking.com/2012/12/22/what-is-new-on-the-PPTP-inspection-on-the-ASA/

Try and let me know

Julio

LAN to Lan tunnel between ASA 5505 and 3030.

I am unable to build a tunnel vpn site-to-site between an ASA 5505 and our Cisco 3030. I tried all possible combinations except one that will work. I am able to ping each peer on the other site. Someone at - it a config between two tunnels of Lan to Lan to work between a 5505 and 3030 that works. Thank you

Hello

Please visit this link using config:

http://www.Cisco.com/c/en/us/support/docs/security/VPN-3000-series-conce...

Kind regards

Aditya

Please evaluate the useful messages.

VLANS with Cisco ASA 5505 and non-Cisco switch

I have an ASA5505 and a switch Netgear GSM7224 L2 that I try to use together. I can't grasp how VLANs (or at least how they should be put in place). When configuring my VLAN on the ASA5505 it seems simple enough, but then on my switch, I thought I'd create just the same VLAN numbers that I used on the SAA and then add the ports that I wanted to use for each VLAN.

Currently on my ASA, I have the following VLAN configured...

outside - vlan11 - Port 0/0

inside - vlan1 - Port 0/1

dmz_ftp - vlan21 - Port 0/2

Port of Corp - vlan31 - 0/3

I need to do the same thing on my switch as well... On my way, I'm a little confused as to how I need to configure the VLAN. Below is the screenshot of web GUI...

Note: Normally you can now change the VLAN ID (red), but in this case the default vlan (vlan id 1) may not be changed or deleted, you can does not change its settings.

Tagged (green), Untagged (purple) and Autodetect (yellow) you must select at least 1. I'm not sure how to in one place to tell my inner vlan (vlan1).

I want VLAN1 ports 1-8 on my Netgear switch used alone to talk to interface/0/1 on the ASA5505 port. I don't want to NOT port 9-24 able to talk to ports 1-8 on the Netgear switch ports OR 0/0, 0/2 - 0 / 7 on the Cisco ASA 5505.

So, how can I configure my inner Vlan1 on ports 1-8 on the switch? Do mark, UNTAG, autodetect them? What about tours? I've been a bit the impression that I would set up my VLAN on both devices, then trunk port 1 and dedicate this port on both devices to nothing other than the sheath and the security of vlan would then take the packages where they need to go. Is this the wrong logic?

Hi Arvo,

If the port of the ASA is just part of a single VLAN (i.e. e0/0 single door 11 VLAN), this is called an access port. If the port of the ASA had to carry several VLANs, it would constitute a Trunk port.

To access ports (VLAN unique), you must set the switch corresponding to be unidentified for port this VLAN individual. If you decide to configure a trunk port, then the port of the switch must be set for labelling for each of VLAN who win the trunk.

For example, ASA I have:
```
interface Ethernet0/1
switchport access vlan 20
!
interface Vlan20
nameif inside
security-level 100
ip address 192.168.100.254 255.255.255.0
```
With the above configuration, the configuration of the switch would look like this (assuming the e0/1 port of the SAA is connected to 0/1 on the switch):
```
VLAN 20 - 0/1 = untagged
```
If instead you use a trunk port, the config would look like this:
```
interface Ethernet0/0
switchport trunk allowed vlan 10,20
switchport mode trunk
!
interface Vlan10
nameif outside
security-level 0
ip address dhcp setroute
!
interface Vlan20
nameif inside
security-level 100
ip address 192.168.100.254 255.255.255.0
```
Assuming that the ASA e0/0 port is connected to 0/1 on the switch):
```
VLAN 10 - 0/1 = tagged
VLAN 20 - 0/1 = tagged
```
Hope that helps.

-Mike

EzVPN between Cisco ASA 5505 (with NEM mode) and Ciscoo 881 Roure

Hi friends,

I configured the Cisco ASA 5505 and Cisco router with DMVPN 881. 3 offices works very well but one office remains failure. I did the same configuration for all facilities but this router does not work. Any ideas?

Please find below the exit of 881 router Cisco:

YF2_Tbilisi_router #.
* 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:26.793 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 4 August 09:31:26.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:31:26.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:26.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:36.793 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
* 4 August 09:31:36.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:31:36.793: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:36.793 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 09:31:44.929 4 August: ISAKMP: (0): serving SA., its is 88961 B 34, delme is 88961 B 34
* 4 August 09:31:46.793: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:46.793 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

* 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:31:46.793 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
* 4 August 09:31:46.793: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
* 09:31:46.793 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:31:46.793 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
* 09:31:46.793 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
* 09:31:46.793 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 09:31:46.793 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

* 4 August 09:31:47.805: del_node 2.2.2.2 src dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
* 09:31:47.805 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

* 4 August 09:31:47.805: ISAKMP: (0): profile of THE request is (NULL)
* 09:31:47.805 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
* 09:31:47.805 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004819
* 09:31:47.805 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
* 09:31:47.805 4 August: ISAKMP: (0): client configuration parameters 87531228 adjustment
* 09:31:47.805 4 August: ISAKMP: 500 local port, remote port 500
* 09:31:47.805 4 August: ISAKMP: find a dup her to the tree during his B 88961, 34 = isadb_insert call BVA
* 4 August 09:31:47.805: ISAKMP: (0): set up client mode.
* 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 4 August 09:31:47.805: ISAKMP: (0): built the seller-07 ID NAT - t
* 4 August 09:31:47.805: ISAKMP: (0): built of NAT - T of the seller-03 ID
* 4 August 09:31:47.805: ISAKMP: (0): built the seller-02 ID NAT - t
* 4 August 09:31:47.805: ISKAMP: more send buffer from 1024 to 3072
* 09:31:47.805 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
* 09:31:47.805 4 August: ISAKMP (0): payload ID
next payload: 13
type: 11
Group ID: Youth_Facility_2
Protocol: 17
Port: 0
Length: 24
* 09:31:47.805 4 August: ISAKMP: (0): the total payload length: 24
* 09:31:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
* 09:31:47.809 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

* 4 August 09:31:47.809: ISAKMP: (0): Beginner aggressive Mode Exchange
* 4 August 09:31:47.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:47.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:31:57.809 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 4 August 09:31:57.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:31:57.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:31:57.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:07.809 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 4 August 09:32:07.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:07.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:07.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:17.809 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 4 August 09:32:17.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:17.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:17.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:27.809 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 4 August 09:32:27.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:27.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:27.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:37.809 4 August: ISAKMP (0): increment the count of errors on his, try 5 of 5: retransmit the phase 1
* 4 August 09:32:37.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:37.809: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:37.809 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 09:32:46.793 4 August: ISAKMP: (0): serving SA., his is 872E1504, delme is 872E1504
* 4 August 09:32:47.809: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:47.809 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

* 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:32:47.809 4 August: % CRYPTO-6-EZVPN_CONNECTION_DOWN: user (customer) = group = Youth_Facility_2 Server_public_addr = 1.1.1.1
* 4 August 09:32:47.809: ISAKMP:isadb_key_addr_delete: no key for address 1.1.1.1 (root NULL)
* 09:32:47.809 4 August: ISAKMP: (0): removal of reason ITS status of 'Death by retransmission P1' (I) AG_INIT_EXCH (peer 1.1.1.1)
* 09:32:47.809 4 August: ISAKMP: Unlocking counterpart struct 0x8AA90C50 for isadb_mark_sa_deleted(), count 0
* 09:32:47.809 4 August: ISAKMP: delete peer node by peer_reap for 1.1.1.1: 8AA90C50
* 09:32:47.809 4 August: ISAKMP: (0): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
* 09:32:47.809 4 August: ISAKMP: (0): former State = new State IKE_I_AM1 = IKE_DEST_SA

* 4 August 09:32:48.909: del_node src 2.2.2.2:500 dst 1.1.1.1:500 fvrf 0 x 0, ivrf 0 x 0
* 09:32:48.909 4 August: ISAKMP: (0): the peer is not paranoid KeepAlive.

* 4 August 09:32:48.909: ISAKMP: (0): profile of THE request is (NULL)
* 09:32:48.909 4 August: ISAKMP: created a struct peer 1.1.1.1, peer port 500
* 09:32:48.909 4 August: ISAKMP: new created position = 0x8AA90C50 peer_handle = 0 x 80004818
* 09:32:48.909 4 August: ISAKMP: lock struct 0x8AA90C50, refcount 1 to peer isakmp_initiator
* 09:32:48.909 4 August: ISAKMP: (0): client setting Configuration parameters 88C05A48
* 09:32:48.909 4 August: ISAKMP: 500 local port, remote port 500
* 09:32:48.909 4 August: ISAKMP: find a dup her to the tree during the isadb_insert his 87B57D38 = call BVA
* 4 August 09:32:48.909: ISAKMP: (0): set up client mode.
* 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-rfc3947 ID
* 4 August 09:32:48.909: ISAKMP: (0): built the seller-07 ID NAT - t
* 4 August 09:32:48.909: ISAKMP: (0): built of NAT - T of the seller-03 ID
* 4 August 09:32:48.909: ISAKMP: (0): built the seller-02 ID NAT - t
* 4 August 09:32:48.909: ISKAMP: more send buffer from 1024 to 3072
* 09:32:48.913 4 August: ISAKMP: (0): ITS been pre-shared key and XAUTH authentication using id ID_KEY_ID type
* 09:32:48.913 4 August: ISAKMP (0): payload ID
next payload: 13
type: 11
Group ID: Youth_Facility_2
Protocol: 17
Port: 0
Length: 24
* 09:32:48.913 4 August: ISAKMP: (0): the total payload length: 24
* 09:32:48.913 4 August: ISAKMP: (0): entry = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_AM
* 09:32:48.913 4 August: ISAKMP: (0): former State = new State IKE_READY = IKE_I_AM1

* 4 August 09:32:48.913: ISAKMP: (0): Beginner aggressive Mode Exchange
* 4 August 09:32:48.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:48.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:32:58.913 4 August: ISAKMP (0): increment the count of errors on his, try 1 5: retransmit the phase 1
* 4 August 09:32:58.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:32:58.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:32:58.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:33:08.913 4 August: ISAKMP (0): increment the count of errors on his, try 2 of 5: retransmit the phase 1
* 4 August 09:33:08.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:33:08.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:33:08.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:33:18.913 4 August: ISAKMP (0): increment the count of errors on his, try 3 of 5: retransmit the phase 1
* 4 August 09:33:18.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:33:18.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:33:18.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.
* 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH...
* 09:33:28.913 4 August: ISAKMP (0): increment the count of errors on his, try 4 out 5: retransmit the phase 1
* 4 August 09:33:28.913: ISAKMP: (0): transmit phase 1 AG_INIT_EXCH
* 4 August 09:33:28.913: ISAKMP: (0): 1.1.1.1 package sending 500 peer_port 500 (I) my_port AG_INIT_EXCH
* 09:33:28.913 4 August: ISAKMP: (0): sending a packet IPv4 IKE.

There is no DMVPN on the SAA. All that you have configured, is not compatible with the ASA or something another DMVPN then. At least debugging shows that there are some EzVPN involved.

The debug version, it seems that there is no communication on UDP/500 possible between devices. Maybe something is blocking who?

Site to Site VPN between Cisco ASA 5505 and Sonicwall TZ170

I'm trying to implement a VPN site-to site between our data center and office. The data center has a Cisco ASA 5505 and the Office has a Sonicwall TZ170. I managed to configure the two so that the vpn connects. Each of the firewall I ping the IP Address of the internet firewall on the other side and a desktop computer I can ping the IP Address of the firewall internal datacenter but I can't carry traffic between private subnets datacenter and desktop. Can anyone help?

The config below has had IPs/passwords has changed.

External Datacenter: 1.1.1.4

External office: 1.1.1.1

Internal data center: 10.5.0.1/24

Internal office: 10.10.0.1/24

: Saved
:
ASA Version 8.2 (1)
!
hostname datacenterfirewall
mydomain.tld domain name
activate the password encrypted
passwd encrypted
names of
name 10.10.0.0 OfficeNetwork
10.5.0.0 DatacenterNetwork name
!
interface Vlan1
nameif inside
security-level 100
10.5.0.1 IP address 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
1.1.1.4 IP address 255.255.255.0
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone IS - 5
clock to summer time EDT recurring
DNS server-group DefaultDNS
buydomains.com domain name
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
inside_access_in list extended access permit icmp any one
inside_access_in list extended access permitted tcp a whole
inside_access_in list extended access udp allowed a whole
inside_access_in of access allowed any ip an extended list
outside_access_in list extended access permit icmp any one
outside_access_in list extended access udp allowed any any eq isakmp
IP DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0 allow Access-list extended pixtosw
pixtosw list extended access allow icmp DatacenterNetwork 255.255.255.0 OfficeNetwork 255.255.255.0
IP OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0 allow Access-list extended pixtosw
pixtosw list extended access allow icmp OfficeNetwork 255.255.255.0 DatacenterNetwork 255.255.255.0
outside_cryptomap_66.1 list of allowed ip extended access all OfficeNetwork 255.255.255.0
outside_cryptomap_66.1 ip OfficeNetwork 255.255.255.0 allowed extended access list all
outside_cryptomap_66.1 list extended access permit icmp any OfficeNetwork 255.255.255.0
outside_cryptomap_66.1 list extended access allowed icmp OfficeNetwork 255.255.255.0 everything
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
IP verify reverse path to the outside interface
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 623.bin
don't allow no asdm history
ARP timeout 14400
NAT-control
Global 1 interface (outside)
NAT (inside) 1 0.0.0.0 0.0.0.0
inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Route inside 0.0.0.0 0.0.0.0 1.1.1.1 1
Route OfficeNetwork 255.255.255.0 outside 1.1.1.1 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
Enable http server
http 10.5.0.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set esp-aes-256 walthamoffice, esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
Crypto dynamic-map ciscopix 1 corresponds to the address outside_cryptomap_66.1
Crypto dynamic-map ciscopix 1 transform-set walthamoffice
Crypto dynamic-map ciscopix 1 the value reverse-road
map dynmaptosw 66-isakmp ipsec crypto dynamic ciscopix
dynmaptosw interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
crypto ISAKMP policy 13
preshared authentication
aes-256 encryption
sha hash
Group 2
lifetime 28800
crypto ISAKMP policy 30
preshared authentication
aes-256 encryption
sha hash
Group 2
life 86400
No encryption isakmp nat-traversal
Telnet 10.5.0.0 255.255.255.0 inside
Telnet timeout 5
SSH 10.5.0.0 255.255.255.0 inside
SSH timeout 5
Console timeout 0
management-access inside
dhcpd address 10.5.0.2 - 10.5.0.254 inside
dhcpd allow inside
!

a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
NTP server 66.250.45.2 source outdoors
NTP server 72.18.205.157 source outdoors
NTP server 208.53.158.34 source outdoors
WebVPN
attributes of Group Policy DfltGrpPolicy
VPN-idle-timeout no
username admin password encrypted
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared-key *.
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
!
context of prompt hostname
Cryptochecksum:7f319172e5de9c0e550804a263f8e49e
: end

Mattew, obvious lack of education is the rule exempt from nat for your tunnel, your access list pixtosw is similar on this example, I assume that you have gone through this link, if it does not see the configs on both sides.

Add the statement of rule sheep in asa and try again.

NAT (inside) 0-list of access pixtosw

http://www.Cisco.com/en/us/products/HW/vpndevc/ps2030/products_configuration_example09186a008052c9d4.shtml

Concerning

Site to site VPN upward but not pass traffic (ASA 5505 8.3.1 and 9.2.3 version)

Hello

I'll put up a tunnel vpn site-to-site between two locations. Both have cisco ASA 5505 running a different version, I'll explain in more detail below. so far, I was able to get the tunnel to come but I can't seem to pass traffic, I work at this for days now and have not been able to understand why he will not pass traffic. Needless to say that the customer's PO would be on the fact that their VPN is not upward and they had to do by hand. I'll put the configs below, if possible can someone help me as soon as POSSIBLE, I really want to get this site up and running so that we do not lose the customer.

An IP address of 0.0.0.0 = site
Site B IP = 1.1.1.1

A Version of the site = 8.3.1
Version of the site B = 9.2.3

__________________________

_________

A RACE OF THE SITE CONFIGURATION

Output of the command: "sh run".

: Saved
:
ASA Version 8.3 (1)
!
hostname SDMCLNASA01
SDMCLNASA01 domain name. LOCAL
Select 5E8js/Fs7qxjxWdp of encrypted password
2KFQnbNIdI.2KYOU encrypted passwd
names of
!
interface Vlan1
nameif inside
security-level 100
the IP 192.168.0.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
the IP 0.0.0.0 255.255.255.252
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
SDMCLNASA01 domain name. LOCAL
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_192.168.0.0_24 object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
network lan_internal object
192.168.0.0 subnet 255.255.255.0
purpose of the smtp network
Home 192.168.0.245
Network http object
Home 192.168.0.245
rdp network object
Home 192.168.0.245
network ssl object
Home 192.168.0.245
network camera_1 object
host 192.168.0.13
network camerahttp object
host 192.168.0.13
service object 8081
source eq 8081 destination eq 8081 tcp service
Dvr description
network camera-http object
host 192.168.0.13
network dvr-http object
host 192.168.0.13
network dvr-mediaport object
host 192.168.0.13
object-group Protocol DM_INLINE_PROTOCOL_1
object-protocol udp
object-tcp protocol
object-group Protocol TCPUDP
object-protocol udp
object-tcp protocol
DM_INLINE_TCP_1 tcp service object-group
EQ port 3389 object
port-object eq www
EQ object of the https port
EQ smtp port object
DM_INLINE_TCP_2 tcp service object-group
port-object eq 34567
port-object eq 34599
EQ port 8081 object
permit access ip 192.168.0.0 scope list outside_1_cryptomap 255.255.255.0 192.168.1.0 255.255.255.0
outside_access_in list extended access permit tcp any any eq smtp
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_1 object-group
outside_access_in list extended access permit tcp any any DM_INLINE_TCP_2 object-group
permit access ip 192.168.0.0 scope list inside_nat0_outbound 255.255.255.0 192.168.1.0 255.255.255.0
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
don't allow no asdm history
ARP timeout 14400
NAT (inside, outside) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
!

network lan_internal object
NAT dynamic interface (indoor, outdoor)
purpose of the smtp network
NAT (all, outside) interface static tcp smtp smtp service
Network http object
NAT (all, outside) interface static tcp www www service
rdp network object
NAT (all, outside) interface static service tcp 3389 3389
network ssl object
NAT (all, outside) interface static tcp https https service
network dvr-http object
NAT (all, outside) interface static 8081 8081 tcp service
network dvr-mediaport object
NAT (all, outside) interface static 34567 34567 tcp service
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 71.42.194.209 1
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
http server enable 8080
http 192.168.0.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 inside
http 192.168.1.0 255.255.255.0 outside
http 71.40.221.136 255.255.255.252 inside
http 71.40.221.136 255.255.255.252 outside
http 192.168.0.0 255.255.255.0 outside
http 97.79.197.42 255.255.255.255 inside
http 97.79.197.42 255.255.255.255 outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
card crypto outside_map 1 match address outside_1_cryptomap
card crypto outside_map 1 set peer 1.1.1.1
card crypto outside_map 1 set of transformation-ESP-3DES-SHA
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 65535
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd address 192.168.0.50 - 192.168.0.150 inside
dhcpd dns 192.168.0.245 209.18.47.62 interface inside
dhcpd SDMCLNASA01 field. LOCAL inside interface
dhcpd allow inside
!

a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
attributes of Group Policy DfltGrpPolicy
Protocol-tunnel-VPN IPSec l2tp ipsec
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared key *.
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
!
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:462428c25e9748896e98863f2d8aeee7
: end

________________________________

SITE B RUNNING CONFIG

Output of the command: "sh run".

: Saved
:
: Serial number: JMX1635Z1BV
: Material: ASA5505, 512 MB RAM, 500 MHz Geode Processor
:
ASA Version 9.2 (3)
!
ciscoasa hostname
activate qddbwnZVxqYXToV9 encrypted password
volatile xlate deny tcp any4 any4
volatile xlate deny tcp any4 any6
volatile xlate deny tcp any6 any4
volatile xlate deny tcp any6 any6
volatile xlate deny udp any4 any4 eq field
volatile xlate deny udp any4 any6 eq field
volatile xlate deny udp any6 any4 eq field
volatile xlate deny udp any6 any6 eq field
names of
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP 1.1.1.1 255.255.255.252
!
passive FTP mode
clock timezone CST - 6
clock to summer time recurring CDT
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
network camera_http object
host 192.168.1.13
network camera_media object
host 192.168.1.13
network of the NETWORK_OBJ_192.168.0.0_24 object
192.168.0.0 subnet 255.255.255.0
network of the NETWORK_OBJ_192.168.1.0_24 object
subnet 192.168.1.0 255.255.255.0
outside_access_in list extended access permit tcp any any eq 9000
outside_access_in list extended access permit tcp any any eq www
outside_access_in list extended access permit icmp any one
outside_cryptomap to access ip 192.168.1.0 scope list allow 255.255.255.0 object NETWORK_OBJ_192.168.0.0_24
pager lines 24
Enable logging
asdm of logging of information
Within 1500 MTU
Outside 1500 MTU
no failover
ICMP unreachable rate-limit 1 burst-size 1
ICMP allow any inside
ICMP allow all outside
ASDM image disk0: / asdm - 732.bin
don't allow no asdm history
ARP timeout 14400
no permit-nonconnected arp
NAT (inside, outside) static static source NETWORK_OBJ_192.168.0.0_24 destination NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.0.0_24
NAT (exterior, Interior) static static source NETWORK_OBJ_192.168.1.0_24 destination NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.0.0_24 NETWORK_OBJ_192.168.1.0_24
!
network camera_http object
NAT (all, outside) interface static tcp www www service
network camera_media object
NAT (all, outside) interface static 9000 9000 tcp service
!
NAT source auto after (indoor, outdoor) dynamic one interface
Access-group outside_access_in in interface outside
Route outside 0.0.0.0 0.0.0.0 71.40.221.137 1
Timeout xlate 03:00
Pat-xlate timeout 0:00:30
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
Floating conn timeout 0:00:00
dynamic-access-policy-registration DfltAccessPolicy
identity of the user by default-domain LOCAL
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-AES-128-SHA-TRANS-aes - esp esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-TRANS-aes - esp esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-128-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-192-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-AES-256-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-3DES-MD5-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac
Crypto ipsec transform-set ikev1 ESP-DES-SHA-TRANS esp - esp-sha-hmac
Crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transit
Crypto ipsec transform-set ikev1 ESP-DES-MD5-TRANS esp - esp-md5-hmac
Crypto ipsec ikev1 transform-set ESP-DES-MD5-TRANS mode transit
Crypto ipsec ikev2 AES256 ipsec-proposal
Protocol esp encryption aes-256
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES192
Protocol esp encryption aes-192
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal AES
Esp aes encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 proposal ipsec 3DES
Esp 3des encryption protocol
Esp integrity sha - 1, md5 Protocol
Crypto ipsec ikev2 ipsec-proposal OF
encryption protocol esp
Esp integrity sha - 1, md5 Protocol
Crypto ipsec pmtu aging infinite - the security association
card crypto outside_map 1 match address outside_cryptomap
card crypto outside_map 1 peer set 0.0.0.0
card crypto outside_map 1 set transform-set ESP-3DES-SHA ikev1
outside_map interface card crypto outside
trustpool crypto ca policy
IKEv2 crypto policy 1
aes-256 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 10
aes-192 encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 20
aes encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 30
3des encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
IKEv2 crypto policy 40
the Encryption
integrity sha
Group 2 of 5
FRP sha
second life 86400
Crypto ikev1 allow outside
IKEv1 crypto policy 120
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet timeout 5
SSH stricthostkeycheck
SSH timeout 5
SSH group dh-Group1-sha1 key exchange
Console timeout 0

dhcpd address 192.168.1.50 - 192.168.1.150 inside
dhcpd dns 192.168.0.245 209.18.47.61 interface inside
dhcpd SDPHARR field. LOCAL inside interface
dhcpd allow inside
!
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
AnyConnect essentials
attributes of Group Policy DfltGrpPolicy
Ikev1 VPN-tunnel-Protocol
internal GroupPolicy_0.0.0.0 group strategy
attributes of Group Policy GroupPolicy_0.0.0.0
VPN-tunnel-Protocol ikev1, ikev2
tunnel-group 0.0.0.0 type ipsec-l2l
tunnel-group 0.0.0.0 ipsec-attributes
IKEv1 pre-shared-key *.
remote control-IKEv2 pre-shared-key authentication *.
pre-shared-key authentication local IKEv2 *.
!
!
!
type of policy-card inspect dns preset_dns_map
parameters
maximum message length automatic of customer
message-length maximum 512
!
context of prompt hostname
no remote anonymous reporting call
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:19031ab1e3bae21d7cc8319fb7ecf0eb
: end
Sorry my mistake.

Delete this if it's still there

card crypto external_map 1 the value reverse-road

Add this to both sides

card crypto outside_map 1 the value reverse-road

Sorry about that.

Mike

How to accompany the IDS in ASA 5505 and 5520?

Dear All;

We have the following configuration of HW for the ASA 5505 and ASA 5520, we add the functionality of system of detection of Intrusion (IDS) to the two ASA. My question is: what are the modules required to support this function, and what is the deference between IPS and IDS, fact the same Module both the feature?

Part number:	Description	QTY.
ASA5505-BUN-K9	ASA 5505 appliance with SW 10 users, 8 ports, 3DES/AES	1
CON-SNT-AS5BUNK9	SMARTNET 8X5XNBD ASA5505-BUN-K9	1
SF-ASA5505 - 8.2 - K8	ASA 5505 Series Software v8.2	1
CAB-AC-C5	Power supply cord Type C5 U.S.	1
ASA5500-BA-K9	ASA 5500 license (3DES/AES) encryption	1
ASA5505-PWR-AC	ASA 5505 power adapter	1
ASA5505-SW-10	ASA 5505 10 user software license	1
SSC-WHITE	ASA 5505 hood SSC of the location empty	1
ASA-ANYCONN-CSD-K9	ASA 5500 AnyConnect Client + Cisco Security Office software	1

Part number:	Description	QTY.
ASA5520-BUN-K9	ASA 5520 appliance with SW HA, 4GE + 1FE, 3DES/AES	2
CON-SNT-AS2BUNK9	SMARTNET 8X5XNBD ASA5520 w/300 VPN Prs 4GE + 1FE3DES/AES	2
ASA5520-VPN-PL	ASA 5520 VPN over 750 IPsec User License (7.0 only)	2
ASA-VPN-CLNT-K9	Cisco VPN Client (Windows Solaris Linux Mac) software	2
SF - ASA - 8.2 - K8	ASA 5500 Series Software v8.2	2
CAB - ACU	Power supply cord (UK) C13 BS 1363 2.5 m	2
ASA-180W-PWR-AC	Power supply ASA 180W	2
ASA5500-BA-K9	ASA 5500 license (3DES/AES) encryption	2
ASA-ANYCONN-CSD-K9	ASA 5500 AnyConnect Client + Cisco Security Office software	2
SSM-WHITE	ASA/IPS SSM hood of the location	2

Thanks in advance.

Rashed Ward.

Okay, I was not quite correct in my first post.

These modules - modules only available for corresponding models of ASA.

They all can act as IPS (inline mode) or IDS ("Promiscuous" mode), depending on how you configure your policies.

When acting as IPS, ASA redirects all traffic through the module, then all the traffic is inspected and can be dropped inline if a signature is triggered.

When she acts as an ID, ASA a few exemplary traffic is the module for inspection, but the actual traffic is not affected by the module, as it's not inline in this case.

In addition, these modules can be both comdination. That is part of the traffic can be inspected "inline", when some other (more sensitive) traffic can be inspected in promiscuous mode.

To better understand, familiarize themselves with this link:

http://www.Cisco.com/en/us/docs/security/ASA/asa84/configuration/guide/modules_ips.html

VPN site-to-site between ASA 5505 and 2911

Hi all

I'm trying to setup VPN S2S. A.a.a.a of ip for the router 2911 office, remote office ASA 5505 8.4 (3) with ip b.b.b.b, but no luck.

2911 config:

version 15.2

horodateurs service debug datetime msec

Log service timestamps datetime msec

encryption password service

host name 2911

boot-start-marker

Boot system flash c2900-universalk9-mz. Spa. 152 - 2.T.bin

boot-end-marker

Min-length 10 Security passwords

logging buffered 51200 warnings

No aaa new-model

min-threshold queue spd IPv6 62

Max-threshold queue spd IPv6 63

No ipv6 cef

the 5 IP auth-proxy max-login-attempts

max-login-attempts of the IP 5 admission

DHCP excluded-address IP 192.168.10.1 192.168.10.99

DHCP excluded-address IP 192.168.22.1 192.168.22.99

DHCP excluded-address IP 192.168.33.1 192.168.33.99

DHCP excluded-address IP 192.168.44.1 192.168.44.99

DHCP excluded-address IP 192.168.55.1 192.168.55.99

192.168.10.240 IP dhcp excluded-address 192.168.10.254

DHCP excluded-address IP 192.168.22.240 192.168.22.254

DHCP excluded-address IP 192.168.33.240 192.168.33.254

DHCP excluded-address IP 192.168.44.240 192.168.44.254

DHCP excluded-address IP 192.168.55.240 192.168.55.254

desktop IP dhcp pool

import all

network 192.168.33.0 255.255.255.0

router by default - 192.168.33.254

192.168.10.10 DNS server 202.50.246.41 202.50.246.42

local domain name

-192.168.10.10 NetBIOS name server

h-node NetBIOS node type

wi - fi IP dhcp pool

import all

network 192.168.44.0 255.255.255.0

192.168.10.10 DNS server 202.50.246.41 202.50.246.42

local domain name

router by default - 192.168.44.254

-192.168.10.10 NetBIOS name server

h-node NetBIOS node type

DMZ IP dhcp pool

import all

network 192.168.55.0 255.255.255.0

192.168.10.10 DNS server 202.50.246.41 202.50.246.42

local domain name

router by default - 192.168.55.254

-192.168.10.10 NetBIOS name server

h-node NetBIOS node type

IP dhcp pool voip

import all

network 192.168.22.0 255.255.255.0

192.168.10.10 DNS server 202.50.246.41 202.50.246.42

local domain name

router by default - 192.168.22.254

-192.168.10.10 NetBIOS name server

h-node NetBIOS node type

IP dhcp pool servers

import all

network 192.168.10.0 255.255.255.0

default router 192.168.10.254

192.168.10.10 DNS server 202.50.246.41 202.50.246.42

local domain name

-192.168.10.10 NetBIOS name server

h-node NetBIOS node type

IP domain name of domain

name-server IP 192.168.10.10

IP cef

connection-for block 180 tent 3-180

Timeout 10

VLAN ifdescr detail

Authenticated MultiLink bundle-name Panel

Crypto pki token removal timeout default 0

Crypto pki trustpoint TP-self-signed-3956567439

enrollment selfsigned

name of the object cn = IOS - Self - signed - certificate - 3956567439

revocation checking no

rsakeypair TP-self-signed-3956567439

TP-self-signed-3956567439 crypto pki certificate chain

certificate self-signed 01 nvram:IOS - Self-Sig #1.cer

license udi pid sn CISCO2911/K9

the FULL_NET object-group network

full range of the network Description

192.168.10.0 255.255.255.0

192.168.11.0 255.255.255.0

192.168.22.0 255.255.255.0

192.168.33.0 255.255.255.0

192.168.44.0 255.255.255.0

object-group network limited

description without servers and router network

192.168.22.0 255.255.255.0

192.168.33.0 255.255.255.0

192.168.44.0 255.255.255.0

VTP version 2

password username admin privilege 0 password 7

redundancy

no passive ftp ip

crypto ISAKMP policy 10

BA aes 256

sha512 hash

preshared authentication

ISAKMP crypto key admin address b.b.b.b

invalid-spi-recovery crypto ISAKMP

Crypto ipsec transform-set esp - aes esp-sha-hmac SET

10 map ipsec-isakmp crypto map

the value of b.b.b.b peer

Set transform-set

match address 160

Interface Port - Channel 1

no ip address

waiting-150 to

Interface Port - channel1.1

encapsulation dot1Q 1 native

IP 192.168.11.254 255.255.255.0

IP nat inside

IP virtual-reassembly in

Interface Port - channel1.10

encapsulation dot1Q 10

IP address 192.168.10.254 255.255.255.0

IP nat inside

IP virtual-reassembly in

Interface Port - channel1.22

encapsulation dot1Q 22

IP 192.168.22.254 255.255.255.0

IP nat inside

IP virtual-reassembly in

Interface Port - channel1.33

encapsulation dot1Q 33

IP 192.168.33.254 255.255.255.0

IP nat inside

IP virtual-reassembly in

Interface Port - channel1.44

encapsulation dot1Q 44

IP 192.168.44.254 255.255.255.0

IP nat inside

IP virtual-reassembly in

Interface Port - channel1.55

encapsulation dot1Q 55

IP 192.168.55.254 255.255.255.0

IP nat inside

IP virtual-reassembly in

the Embedded-Service-Engine0/0 interface

no ip address

Shutdown

interface GigabitEthernet0/0

Description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-GE $ 0/0

no ip address

Shutdown

automatic duplex

automatic speed

interface GigabitEthernet0/1

no ip address

automatic duplex

automatic speed

channel-group 1

interface GigabitEthernet0/2

Description $ES_LAN$

no ip address

automatic duplex

automatic speed

channel-group 1

interface GigabitEthernet0/0/0

IP address a.a.a.a 255.255.255.224

NAT outside IP

IP virtual-reassembly in

automatic duplex

automatic speed

crypto map

IP forward-Protocol ND

no ip address of the http server

23 class IP http access

local IP http authentication

IP http secure server

IP http timeout policy slowed down 60 life 86400 request 10000

overload of IP nat inside source list NAT_INTERNET interface GigabitEthernet0/0/0

IP nat inside source udp 500 interface GigabitEthernet0/0/0 500 a.a.a.a static

IP route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx

NAT_INTERNET extended IP access list

refuse the object-group ip FULL_NET 192.168.17.0 0.0.0.255

refuse the object-group ip FULL_NET 192.168.1.0 0.0.0.255

permit ip FULL_NET object-group everything

access-list 1 permit 192.168.44.100

access-list 23 allow 192.168.10.7

access-list 23 permit 192.168.44.0 0.0.0.255

access-list 100 permit ip 192.168.10.0 0.0.0.255 192.168.17.0 0.0.0.255

access-list 160 permit ip 192.168.10.0 0.0.0.255 192.168.17.0 0.0.0.255

control plan

Line con 0

password password 7

opening of session

line to 0

line 2

no activation-character

No exec

preferred no transport

transport of entry all

transport output pad rlogin lapb - your MOP v120 udptn ssh telnet

StopBits 1

line vty 0 4

access-class 23 in

privilege level 15

local connection

entry ssh transport

line vty 5 15

access-class 23 in

privilege level 15

local connection

entry ssh transport

Scheduler allocate 20000 1000

end

The ASA config:

: Saved : ASA Version 8.4(3) ! hostname C domain-name domain enable password password encrypted passwd passwd encrypted names ! interface Ethernet0/0 ! interface Ethernet0/1 shutdown ! interface Ethernet0/2 shutdown ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 100 ! interface Ethernet0/6 switchport trunk allowed vlan 2,6 switchport mode trunk ! interface Ethernet0/7 shutdown ! interface Vlan1 description INTERNET mac-address 1234.5678.0001 nameif WAN security-level 0 ip address b.b.b.b 255.255.255.248 standby c.c.c.c ospf cost 10 ! interface Vlan2 description OLD-PRIVATE mac-address 1234.5678.0102 nameif OLD-Private security-level 100 ip address 192.168.17.2 255.255.255.0 standby 192.168.17.3 ospf cost 10 ! interface Vlan6 description MANAGEMENT mac-address 1234.5678.0106 nameif Management security-level 100 ip address 192.168.1.2 255.255.255.0 standby 192.168.1.3 ospf cost 10 ! interface Vlan100 description LAN Failover Interface ! boot system disk0:/asa843-k8.bin ftp mode passive clock timezone NZST 12 clock summer-time NZDT recurring 1 Sun Oct 2:00 3 Sun Mar 2:00 dns domain-lookup WAN dns server-group DefaultDNS name-server 208.67.222.222 domain-name domain same-security-traffic permit intra-interface object network obj-192.168.17.0 subnet 192.168.17.0 255.255.255.0 object network obj-192.168.10.0 subnet 192.168.10.0 255.255.255.0 object network obj-192.168.2.0 subnet 192.168.2.0 255.255.255.0 object network obj-192.168.9.0 subnet 192.168.9.0 255.255.255.0 object network obj-192.168.33.0 subnet 192.168.33.0 255.255.255.0 object network obj-192.168.44.0 subnet 192.168.44.0 255.255.255.0 object network obj_any object network obj_any-01 object network NETWORK_OBJ_192.168.10.0_24 subnet 192.168.10.0 255.255.255.0 object network NETWORK_OBJ_192.168.17.0_24 subnet 192.168.17.0 255.255.255.0 object network subnet-00 subnet 0.0.0.0 0.0.0.0 object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service RDP tcp description RDP port-object eq 3389 object-group network DM_INLINE_NETWORK_1 network-object 192.168.17.0 255.255.255.0 network-object 192.168.10.0 255.255.255.0 network-object 192.168.33.0 255.255.255.0 network-object 192.168.44.0 255.255.255.0 object-group network DM_INLINE_NETWORK_2 network-object 192.168.10.0 255.255.255.0 network-object 192.168.33.0 255.255.255.0 network-object 192.168.44.0 255.255.255.0 object-group network subnet-17 network-object 192.168.17.0 255.255.255.0 object-group network subnet-2 network-object 192.168.2.0 255.255.255.0 object-group network subnet-9 network-object 192.168.9.0 255.255.255.0 object-group network subnet-10 network-object 192.168.10.0 255.255.255.0 access-list LAN_nat0_outbound extended permit ip 192.168.17.0 255.255.255.0 192.168.10.0 255.255.255.0 access-list LAN_nat0_outbound extended permit ip 192.168.17.0 255.255.255.0 192.168.9.0 255.255.255.0 access-list LAN_IP standard permit 192.168.17.0 255.255.255.0 access-list WAN_access_in extended permit ip any any log debugging access-list WAN_access_in extended permit tcp any object-group RDP any object-group RDP log debugging access-list WAN_access_in extended permit icmp x.x.x.x 255.255.255.248 192.168.10.0 255.255.255.0 access-list MANAGEMENT_access_in extended permit ip any any log debugging access-list OLD-PRIVATE_access_in extended permit ip any any log debugging access-list OLD-PRIVATE_access_in extended permit icmp any object-group DM_INLINE_NETWORK_1 access-list 101 extended permit tcp host 192.168.10.7 any eq 3389 log debugging access-list WAN_1_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0 access-list WAN_1_cryptomap extended permit ip 192.168.17.0 255.255.255.0 192.168.9.0 255.255.255.0 access-list WAN_cryptomap_2 extended permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.0 access-list CiscoVPNClient_splitTunnelAcl standard permit 192.168.17.0 255.255.255.0 access-list LAN_access_in extended permit ip any any log debugging access-list WAN_nat0_outbound extended permit ip 192.168.17.0 255.255.255.0 192.168.10.0 255.255.255.0 access-list WAN_nat0_outbound extended permit ip 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0 access-list WAN_nat0_outbound extended permit ip 192.168.17.0 255.255.255.0 192.168.9.0 255.255.255.0 access-list WAN_2_cryptomap extended permit ip 192.168.17.0 255.255.255.0 192.168.10.0 255.255.255.0 access-list WAN_2_cryptomap extended permit ip 192.168.17.0 255.255.255.0 192.168.9.0 255.255.255.0 access-list LAN_IP_inbound standard permit 192.168.10.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 192.168.10.0 255.255.255.0 192.168.17.0 255.255.255.0 access-list vpnusers_splitTunnelAcl extended permit ip 192.168.17.0 255.255.255.0 any access-list nonat-in extended permit ip 192.168.17.0 255.255.255.0 192.168.2.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 52000 logging monitor informational logging trap informational logging asdm informational logging from-address syslog logging recipient-address admin level errors logging host OLD-Private 192.168.17.110 format emblem logging debug-trace logging permit-hostdown mtu WAN 1500 mtu OLD-Private 1500 mtu Management 1500 ip local pool VPN_Admin_IP 192.168.1.150-192.168.1.199 mask 255.255.255.0 ip local pool vpnclient 192.168.2.1-192.168.2.5 mask 255.255.255.0 failover failover lan unit primary failover lan interface failover Vlan100 failover polltime interface 15 holdtime 75 failover key ***** failover interface ip failover 192.168.100.1 255.255.255.0 standby 192.168.100.2 icmp unreachable rate-limit 1 burst-size 1 icmp permit 192.168.10.0 255.255.255.0 WAN icmp permit host x.x.x.x WAN icmp permit 192.168.17.0 255.255.255.0 WAN icmp permit host c.c.c.c WAN icmp permit host a.a.a.a WAN icmp deny any WAN icmp permit 192.168.10.0 255.255.255.0 OLD-Private icmp permit 192.168.17.0 255.255.255.0 OLD-Private icmp permit host a.a.a.a OLD-Private icmp permit host 192.168.10.0 Management icmp permit host 192.168.17.138 Management icmp permit 192.168.1.0 255.255.255.0 Management icmp permit host 192.168.1.26 Management icmp permit host a.a.a.a Management asdm image disk0:/asdm-647.bin no asdm history enable arp timeout 14400 nat (OLD-Private,any) source static subnet-17 subnet-17 destination static subnet-10 subnet-10 no-proxy-arp nat (OLD-Private,any) source static subnet-17 subnet-17 destination static subnet-2 subnet-2 no-proxy-arp nat (OLD-Private,any) source static subnet-17 subnet-17 destination static subnet-9 subnet-9 no-proxy-arp nat (Management,WAN) source static NETWORK_OBJ_192.168.17.0_24 NETWORK_OBJ_192.168.17.0_24 destination static NETWORK_OBJ_192.168.10.0_24 NETWORK_OBJ_192.168.10.0_24 no-proxy-arp route-lookup ! object network subnet-00 nat (OLD-Private,WAN) dynamic interface access-group WAN_access_in in interface WAN access-group OLD-PRIVATE_access_in in interface OLD-Private access-group MANAGEMENT_access_in in interface Management route WAN 0.0.0.0 0.0.0.0 x.x.x.x 1 timeout xlate 3:00:00 timeout pat-xlate 0:00:30 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy user-identity default-domain LOCAL aaa authentication ssh console LOCAL aaa local authentication attempts max-fail 10 http server enable http b.b.b.b 255.255.255.255 WAN http 0.0.0.0 0.0.0.0 WAN no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart service resetoutside crypto ipsec ikev1 transform-set OFFICE esp-aes esp-sha-hmac crypto map WAN_map 1 match address WAN_1_cryptomap crypto map WAN_map 1 set pfs crypto map WAN_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map Office 2 match address WAN_1_cryptomap crypto map Office 2 set peer a.a.a.a crypto map Office interface WAN crypto map MAP 10 set peer a.a.a.a crypto map MAP 10 set ikev1 transform-set OFFICE crypto ikev2 enable WAN crypto ikev1 enable WAN crypto ikev1 policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto ikev1 policy 30 authentication pre-share encryption des hash sha group 1 lifetime 86400 telnet timeout 5 ssh a.a.a.a 255.255.255.255 WAN ssh timeout 30 ssh version 2 console timeout 0 dhcpd auto_config OLD-Private ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server 129.6.15.28 source WAN prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol ikev1 ssl-client ssl-clientless group-policy admin internal group-policy admin attributes dns-server value 208.67.222.222 156.154.70.1 vpn-tunnel-protocol ikev1 group-policy GroupPolicy_a.a.a.a internal group-policy GroupPolicy_a.a.a.a attributes vpn-tunnel-protocol ikev1 ikev2 group-policy CiscoVPNClient internal group-policy CiscoVPNClient attributes vpn-idle-timeout 30 vpn-session-timeout none vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-clientless split-tunnel-policy tunnelspecified split-tunnel-network-list value CiscoVPNClient_splitTunnelAcl username admin password password encrypted privilege 15 tunnel-group admin type remote-access tunnel-group admin general-attributes address-pool vpnclient authorization-server-group LOCAL default-group-policy admin tunnel-group a.a.a.a type ipsec-l2l tunnel-group a.a.a.a general-attributes default-group-policy GroupPolicy_a.a.a.a tunnel-group a.a.a.a ipsec-attributes ikev1 pre-shared-key ***** ikev2 remote-authentication pre-shared-key ***** ikev2 local-authentication pre-shared-key ***** tunnel-group CiscoVPNClient type remote-access tunnel-group CiscoVPNClient general-attributes address-pool vpnclient default-group-policy CiscoVPNClient tunnel-group CiscoVPNClient ipsec-attributes ikev1 pre-shared-key ***** ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters   message-length maximum client auto   message-length maximum 512 policy-map global_policy class inspection_default   inspect dns preset_dns_map   inspect ftp   inspect h323 h225   inspect h323 ras   inspect rsh   inspect rtsp   inspect esmtp   inspect sqlnet   inspect skinny    inspect sunrpc   inspect xdmcp   inspect sip    inspect netbios   inspect tftp   inspect ip-options   inspect icmp ! service-policy global_policy global smtp-server 192.168.17.10 prompt hostname context no call-home reporting anonymous call-home contact-email-addr admin contact-name admin profile CiscoTAC-1   no active : end asdm image disk0:/asdm-647.bin asdm location c.c.c.c 255.255.255.255 WAN asdm location 192.168.17.2 255.255.255.255 WAN asdm location a.a.a.a 255.255.255.255 OLD-Private no asdm history enable

ASA:

# show crypto ipsec his

There is no ipsec security associations

# show crypto isakmp his

There are no SAs IKEv1

There are no SAs IKEv2

2911:

#show crypto ipsec his

Interface: GigabitEthernet0/0/0

Tag crypto map: map, addr a.a.a.a local

protégé of the vrf: (none)

local ident (addr, mask, prot, port): (192.168.10.0/255.255.255.0/0/0)

Remote ident (addr, mask, prot, port): (192.168.17.0/255.255.255.0/0/0)

current_peer b.b.b.b port 500

LICENCE, flags is {origin_is_acl},

#pkts program: encrypt 0, #pkts: 0, #pkts digest: 0

#pkts decaps: 0, #pkts decrypt: 0, #pkts check: 0

compressed #pkts: 0, unzipped #pkts: 0

#pkts uncompressed: 0, #pkts compr. has failed: 0

#pkts not unpacked: 0, #pkts decompress failed: 0

Errors of #send 4, #recv errors 0

local crypto endpt. : a.a.a.a, remote Start crypto. : b.b.b.b

Path mtu 1500, mtu 1500 ip, ip mtu IDB GigabitEthernet0/0/0

current outbound SPI: 0x0 (0)

PFS (Y/N): N, Diffie-Hellman group: no

SAS of the esp on arrival:

-Other - arrival ah sas:

-More-

-More - CFP sas on arrival:

-More-

-More - outgoing esp sas:

-More-

-More - out ah sas:

-More-

-More - out CFP sas:

Thanks for your time,

Nick

Please add

map Office 2 set transform-set OFFICE ikev1 crypto

If it is not helpful, please enable debug crypto ipsec 255 and paste here.

HTH. Please rate if it was helpful. "Correct answer" will be also pleasant.

L2l between an ASA 5505 and WatchGuard XTM330 with dynamic IP

Hi guys,.

I looked for a solution on this one but can't find inappropriate, most of the discussions were old and with dead links to the solution.

We have an ASA 5505 with static IP address on the outside and a customer who have a WatchGuard XTM330 with dynamic IP address to the outside.

Is it possible to have an L2L VPN between our ASA and the WatchGuard when he has a dynamic IP?

I have no experience on the series of WatchGuard,

so, I am very grateful for any answer!

Thanks in advance and have a nice day

BR

Robin

Hi Robin,

Here are the links you can make reference when configuring static to the dynamic VPN tunnel: -.
http://www.Cisco.com/c/en/us/support/docs/security/ASA-5500-x-series-next-generation-firewalls/112075-dynamic-IPSec-ASA-router-CCP.html

This one is with Pix on the remote side, but the configuration will remain the same on the local side: -.
http://www.WatchGuard.com/docs/4-6-Firebox-CiscoPix.PDF

Kind regards
Dinesh Moudgil

PS Please rate helpful messages.

ASA 5505 and ASA 5510 Site to Site VPN Tunnel cannot be established

Hi all experts

We are now plan to form an IPSec VPN tunnel from site to site between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failed, would you please show me how to establish? A reference guide?

I got error syslog 713902 and 713903, how to fix?

I got the following, when I type "sh crypto isakmp his."

Type: user role: initiator

Generate a new key: no State: MM_WAIT_MSG2

Hugo

Hello

This State is reached when the policies of the phase 1 do not correspond to the two ends.

Please confirm that you have the same settings of phase 1 on both sides with the following commands:

See the isakmp crypto race

See the race ikev1 crypto

Also make sure that port UDP 500 and 4500 are open for communication between your device and the remote peer.

Finally, make sure you have a route suitable for the remote VPN endpoint device.

Hope that helps.

Kind regards

Dinesh Moudgil

How can I get voice and data to work with the ASA 5505?

Here's the issue I'm having. Can I get a Cisco 7940 to work behind one site to another configured ASA 5505 and I can also get data to work behind it. However, when I try to create a separate Vlan for voice and data, it does not work. Our voice VLANs on our remote sites are 172.30 and data are 172.31, when I put the inside interface with 172.31 data will work and when I on it 172.30 voice will work. I upgraded to a security more license and tried vlan3 created as voice. I have the data to the top and work but I can't get vlan3 to work. Any help would be greatly appreciated. Thank you

Here is my current config:

hostname TESTvpn
activate the password xxxxx

passwd xxxxx

username admin password xxxxx privilege 15

name Corp_LAN 10.0.0.0
name 192.168.64.0 Corp_Voice
name 172.31.155.0 TESTvpn

object-group network SunVoyager
host of the object-Network 64.70.8.160
host of the object-Network 64.70.8.242

the Corp_Networks object-group network
network-object Corp_LAN 255.0.0.0
object-network Corp_Voice 255.255.255.0

interface vlan2
nameif outside
security-level 0
IP address dhcp setroute
No tap

interface vlan1
nameif inside
security-level 100
IP 172.31.155.1 255.255.255.0
No tap

interface vlan3
nameif Corp_Voice
security-level 100
IP 172.30.155.1 255.255.255.0
No tap

output
interface Ethernet0/0
switchport access vlan 2
No tap

interface Ethernet0/7
switchport access vlan 3
No tap

output

dhcpd allow inside
dhcpd address 172.31.155.10 - 172.31.155.30 inside
dhcpd dns 10.10.10.7 10.10.10.44 interface inside
dhcpd sun.ins area inside interface
dhcpd allow inside

enable Corp_Voice dhcpd
dhcpd address 172.30.155.10 - 172.30.155.30 Corp_Voice
dhcpd dns 10.10.10.7 10.10.10.44 interface Corp_Voice
dhcpd interface of sun.ins of the Corp_Voice domain
enable Corp_Voice dhcpd
dhcpd option 150 ip 192.168.64.4 192.168.64.3

Enable logging
exploitation forest buffer-size 10000
monitor debug logging
logging buffered information
asdm of logging of information

outside_access_in list extended access allow all unreachable icmp
outside_access_in list extended access permit icmp any any echo response
outside_access_in list extended access permit icmp any one time exceed
access extensive list ip 172.31.155.0 inside_access_in allow 255.255.255.0 any
inside_access_in list extended access allow icmp 172.31.155.0 255.255.255.0 any
Access extensive list ip 172.30.155.0 Corp_Voice_access_in allow 255.255.255.0 any
Corp_Voice_access_in list extended access allow icmp 172.30.155.0 255.255.255.0 any

VPN access list extended deny ip 172.31.155.0 255.255.255.0 object-group SunVoyager
extended VPN ip 172.31.155.0 access list allow 255.255.255.0 any

inside_access_in access to the interface inside group
Access-group outside_access_in in interface outside
Access-group Corp_Voice_access_in in the Corp_Voice interface

Global 1 interface (outside)
NAT (inside) 0-list of access VPN
NAT (inside) 1 172.31.155.0 255.255.255.0

Enable http server
http 172.31.155.0 255.255.255.0 inside
http 172.30.155.0 255.255.255.0 Corp_Voice
http 192.168.64.0 255.255.255.0 Corp_Voice
http 10.0.0.0 255.0.0.0 inside
http 65.170.136.64 255.255.255.224 outside
SSH 10.0.0.0 255.0.0.0 inside
SSH 172.31.155.0 255.255.255.0 inside
SSH 65.170.136.64 255.255.255.224 outside
SSH timeout 20

management-access inside

dhcpd outside auto_config

Crypto ipsec transform-set esp-3des esp-md5-hmac VPN
crypto map outside_map 1 is the VPN address
peer set card crypto outside_map 1 66.170.136.65
card crypto outside_map 1 the value transform-set VPN
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 1
preshared authentication
3des encryption
md5 hash
Group 2
lifetime 28800

tunnel-group 66.170.136.65 type ipsec-l2l
IPSec-attributes tunnel-group 66.170.136.65
pre-shared-key xxxxx

output
int eth 0/1
close
No tap
int eth 0/2
close
No tap
int eth 0/3
close
No tap
int eth 0/4
close
No tap
int eth 0/5
close
No tap
int eth 0/6
close
No tap
int eth 0/7
close
No tap

Peter,

Note that access list names are case-sensitive, so you've actually done something different from what I proposed.

Please do:

no nat (Corp_Voice) 0-list of access vpn

No list of vpn access extended permitted ip TESTvpn 255.255.255.0 everything
IP 172.30.155.0 255.255.255.0 extended vpn access do not allow any list all

extended VPN ip 172.30.155.0 access list allow 255.255.255.0 any

NAT (Corp_Voice) 0-list of access VPN

In the case where you did deliberately, for example to separate the 2 acl: note that acl VPN (upper case) is also used in the encryption card, where you cannot add a second LCD.

So if you want to separate you, you will need 3 access lists:

list of access data-vpn ip TESTvpn 255.255.255.0 allow one

voice-vpn ip 172.30.155.0 access list allow 255.255.255.0 any

access-list all - vpn ip TESTvpn 255.255.255.0 allow one

access-list all - vpn ip 172.30.155.0 allow 255.255.255.0 any

NAT (inside) 0-list of access vpn data

NAT (Corp_Voice) - access list 0 voice-vpn

outside_map 1 match address all vpn crypto card

Don't know if this was also clearly to my previous message, I recommend you to replace the "all" (in each of the ACL lines) to something more specific (i.e. a remote network, or group of objects that contain the remote networks).

HTH

Herbert

Cisco asa 5505 and centos VPN server connection

Hi all

Please I want to set up a VPN between Cisco asa 5505 and centos server.

Here's my senerio

-------------------------

ASA 5505

Public IP 155.155.155.2

Local NETWORK: 192.168.6.X

CentOS Server

------------------

Public ip address: 155.155.155.6

Thank you guys

Apology, do you mean access remote VPN Client of hundred BONE for Cisco ASA 5505?

If the remote access, here are the sample configuration:

http://www.Cisco.com/en/us/products/ps6120/products_configuration_example09186a008060f25c.shtml

PPTP and ASA 5505

Similar Questions

Maybe you are looking for