Preflight check customized for the size of the page in the crop marks

Similar Questions

• Creating a custom for the current scale

  Hi guys,.

  I need help in the creation of a custom scale. I read motor current (analog I / P) and I want to show that on a chart and write it to a file. I need to use a linear scaling for custom scale. The slope is 2 and the intersection point is 0. I have attached the code to clearly indicate what I'm currently building. The way I put up right now, it's not the scaling. It has 2 spots in the code. I would like to create a custom for the first task, as in the attached code scale. I had a scale customized using VI to Express DAQ Assistant. But I do not see these options when I try to do the same with the DAQmx task. Please let me know how this can be done. Any help is greatly appreciated.

  Thank you

  REDA

  Ah.

  on the pallate DAQmx > advanced > the balance settings

  There is a scale property node and "Create Scale.vi"

• I have outlook express and the spell checker is for the French. How can I change this?

  I have outlook express and the spell checker is for the French. How can I change this?

  You no longer have the correction spell checking capabilities in some languages in Outlook Express 6.0 after you install the Microsoft Office 2007 or Office 2010 system
  http://support.Microsoft.com/kb/932974

  Outlook Express cannot use the check spelling of MS Word in Office 2007 or newer. A free spell-checking the download is the easiest way to get around this.

  Vampirefo spell check.

  Download from Major Geeks:
  http://www.MajorGeeks.com/download.php?Det=2952

  Or upload it to SnapFile:
  http://www.SnapFiles.com/get/spelloe.html

  You wanted TinySpell or. (Check spelling while typing).

  Download it here:
  http://www.tinyspell.M6.NET/

  Australian English spell checking
  (Also suitable for other English speaking countries).
  http://www.justlocal.com.au/clients/oespellcheck/

  If you have an earlier version of Office, see this:
  http://www.Outlook-tips.NET/archives/2006/20061228.htm

  Bruce Hagen
  MS - MVP October 1, 2004 ~ September 30, 2010
  Imperial Beach, CA

• Emailing to my question mark and supervise the work on the first, then the small e accent when arrives to her frame them and the capital E with the accent comes for the question mark.

  get the e french instead of the question mark or frame them

  Emailing to my question mark and supervise the work on the first, then the small e accent when arrives to her frame them and the capital E with the accent comes for the question mark.  Can you tell me what is the cause and how to fix it.  Thank you.

  Hello

  I suggest you according to the question in this forum and check if that helps:

  http://windowslivehelp.com/forums.aspx?ProductID=15

  It will be useful.

• Filter KeywordFilterField customized for the tabular data model

  I am currently looking for the rows in the table that is filtered through the KeywordFilterField. The underlying data are in table form:

  Contact {name, phone, etc etc}

  The KeywordFilterField shows only what I pass to it (Contact.Name) by calling setSourceList() and filters that the channels in the list. So if I get the numbers, which will return a list empty, because none of the Contacts have numbers in their names.

  However, what I want to do is query the table, like a SQL query, retrieve lines that correspond to a part of Contact.Name or Contact.Phone. (Remember this application don't use SQLite.) I'm using RMS to persistent storage and I created my database and queries of base by hand.)

  Is there a way I could customize/override the filter query so that the KeywordFilterField calls my query functions rather than it's default filter String? It is a base with search CRUD application. I use KeywordFilterField because it's everything I need.

  Any help would be useful.

  It is possible with a text field and a list field, this way you can make your own personalized search for the keyword filter field does not search your data the way you want. In addition, I know that the keyword filter field is broken and that it was returning always completely incorrect search result for me.

  Here's an overview of what to do. Some things I can't tell you how for example to what is happening in the function "searchContacts" since it is up to you to write the code to do whatever custom search you want.

  class CustomKeywordFilterScreen extends MainScreen implements FieldChangeListener, ListFieldCallback
  {
      //just a slightly modified edit field for use in entering keywords
      private CustomKeywordField _filterEdit;
      //a standard list field
      private ListField _countryList;
  
      //temp variable to hold the last keyword searched so we don't search for it again
      //you'll see this used later on
      private String _previousFilterValue;
  
      //any other private vars you need to hold search results go here
      //we'll use an a Contact[] for illustration
      private Contact[] _contactResults;
  
      CustomKeywordFilterScreen()
      {
          super(Manager.VERTICAL_SCROLL | Manager.VERTICAL_SCROLLBAR);
  
          //initiaize to empty string
          _previousFilterValue = "";
  
          //searchContacts is whatever function you write to do the customized search you want,
      //in this example passing an empty string returns all contacts
          _contactResults = searchContacts(_previousFilterValue);
  
          //create the edit field and set it as the title of the screen so it's always visible,
      //even when you scroll the list
          _filterEdit = new CustomKeywordField();
          _filterEdit.setLabel("Search: ");
          _filterEdit.setChangeListener(this);
          setTitle(_filterEdit);
  
          //create the list for showing results
          _contactList = new ListField();
          _countryList.setRowHeight(-2);
          _contactList.setSize(_contactResults.length);
          _contactList.setCallback(this);
          add(_contactList);
      }
  
      protected boolean keyChar(char c, int status, int time)
      {
          if (c == Characters.ESCAPE)
          {
          //user pressed escape key, if there's something in the edit field clear it
          //otherwise handle it as closing the screen or whatever else you want
              if (_filterEdit.getTextLength() > 0)
              {
                  _filterEdit.setText("");
              }
              else
              {
                  //close the screen or do something else, it's your call
                  //maybe even do nothing, whatever you want
              }
              return (true);
          }
          else
          {
          //all other keystrokes set focus on the edit field
              _filterEdit.setFocus();
          }
          return (super.keyChar(c, status, time));
      }
  
      public void fieldChanged(Field field, int context)
      {
          if (field == _filterEdit)
          {
          //test the edit field's value against the previously searched value
          //if NOT the same then do a search and refresh results
              if (!_filterEdit.getText().equals(_previousFilterValue))
              {
              //cache the newest search keyword string
                  _previousFilterValue = _filterEdit.getText();
  
                  //search your data
                  _contactResults = searchContacts(_previousFilterValue);
          //update the list size to cause it to redraw
                  _contactList.setSize(_contactResults.length);
              }
          }
      }
  
      public void drawListRow(ListField listField, Graphics graphics, int index, int y, int width)
      {
          if (listField == _contactList && index > -1 && index < _contactResults.length)
          {
              //draw your list field row as you want it to appear
          }
      }
  
      public Object get(ListField listField, int index)
      {
          if (listField == _contactList && index > -1 && index < _contactResults.length)
          {
              return (_contactResults[index]);
          }
          return (null);
      }
  
      public int getPreferredWidth(ListField listField)
      {
          return (Display.getWidth());
      }
  
      public int indexOfList(ListField listField, String prefix, int start)
      {
          return (-1);
      }
  }
  

  class CustomKeywordField extends EditField
  {
      CustomKeywordField()
      {
          super(USE_ALL_WIDTH | NO_LEARNING | NO_NEWLINE);
      }
  
      protected void paint(Graphics graphics)
      {
          super.paint(graphics);
  
          //Draw caret so the edit field always shows a cursor giving the user an indication they can type at anytime,
      //even when the focus is on the list field that is used in conjunction with this edit field to create a
      //keyword filter field replacement
          getFocusRect(new XYRect());
          drawFocus(graphics, true);
      }
  }
  

• Own sony a7. you want to set the wheel 2 to the size of the APS - C sensor for the cropping effect. Changes to the APS - C for everything

  Tried to adjust the '2' on the dial to include APS - C mode.  But there is APS_C for all other modes.  An easy way to switch to other than menus?  Same for the APS - c and Macro combined.  Thanks for the ideas.

  The setting of APS-C size of Capture, as well as other options under the Menu of the camera custom, can be registered in one of the modes of memory recall only. Only the options under the Menu of the camera of the device can be saved in memory recall mode. In addition, options Menu accessible only via the menu of the camera.

  If my post answered your question, please mark it as "accept as a Solution.

• Customized for the RT FIFO device details

  Hello

  I have a few questions about the FIFO VeriStand in a custom device asyncrounous.

  I saw a post earlier where a - 1 to the function of reading of FIFO of RT for him to wait indefinitely for an item to enter the FIFO. This allows pseudo - synchronize the PCL with a device custom asyncrounous. I wonder if this causes the boundary wire custom sleep or it stay active and keep returning? Is it possible to change the polling to blocking?

  Another quick question, if I only want to write to the RT FIFO when the data has changed it will cause unforeseen problems? As the channels time or need to wake up or something? Certain conditions can only write channels once every 1000 iterations of the PCL and loop device custom.

  I know that I can not write the channels selected in a FIFO RT, but can I create multiple FIFOs in a custom device to actually do the same thing? I imagine then having the outputs 1, outputs etc 2 in VeriStand.

  Thank you

  B

  Hi B,

  If you look at the RT VI pilot generated from custom device model you will see exactly what is happening. If you set the time-out for the reading of FIFO-1 then the botton loop will be essentially suspended unless there are items to read in the FIFO. Meanwhile, the thread will always be active because the RT read that VI is querying data during the time specified in the timeout.  I don't think that there is a way to change the FIFO mode to blocking since the dismissal of the FIFO is spent Veristand engine to the RT VI driver.

  

  The PCL writes and reads data from and to asynchronous custom FIFO device at each step of the execution. In your custom device, you can configure to read and process data of the 1000th step. I don't see any problems with it.

  You can have a FIFO for input channels and a FIFO for the output channels. You can write to an output channel given by writing data in a function index element in the output array that is passed to the function RT FIFO Write.

• How to select the resolution of the PC to the customer for the execution of LV App?

  Hello

  My GUI is 1250 x 812. (assuming that it is the value of a pixel. This is measured using the width and height-> resize option object).  What resolution PC should I offer for the customer who is going to run this GUI?

  Thank you!

  1280 X 1024.

  List of common resolutions

  SXGA (1280 x 1024)

• Signature custom for the maximum number of connections

  Hi, is there a signature to check the maximum number of connection to a host attacker to open a port to the victim? or should I make a costom for this signature?

  Hello

  You certainly can do it on the IP addresses, follow these steps in making a signature Atomic-ip looking for a tcp packet with only the SYN flag set on port 443 to the destination. You would then add a number of events for the number of connections you need. According to the site however this will flood the channel alarm with alerts, because traffic going out etc it will trigger. Of course, this can also be problematic with NAT.

  I don't know one of the guys ASA on these forums could give an answer better than me with regard to the configuration of the SAA.

  I understand they'RE a dynamic IP filtering or something that can be used to do this, although I've never configured myself.

  Thank you

  Neil

• Reports and Plugin check address for the commercial Site

  Hello

  Part of the work of the PEC for our trade application we want to evaluate some plugins for the following areas-

  1 reports plugin - which will allow the generation and display different reports of Commerce site

  2. address verification system - this will check the shipping and billing address users.

  POC, we use the CRS as our basic application. As a POC work requirements are not stringent and most of all, we would like to first of all has the vaniall support in place. Subsequently, we can bring requirements appropriate to the needs to make more cutomized.

  Can you pl share any plug-in module free for the same thing? Any link/blog for the steps to follow for this support will be great.

  Thank you in advance for your support and help.

  Thank you

  Swati

  Hi Swati

  allows to process reports first, Oracle ATG Web Commerce is fully integrated with Oracle ATG Web Commerce Business Intelligence and includes a default set of reports that can provide basic information about the performance of the Bank.

  Refer to the Guide to reports for detailed information on these reports. See the Trade Reporting job preparation chapter of this guide for more setup information.

  http://docs.Oracle.com/CD/E41069_01/platform.11-0/ATGCommProgGuide/HTML/s0102reporting01.html

  http://docs.Oracle.com/CD/E41069_01/ACI.11-0/index.html

  Some deal with audit, you might want to look at: Avatax is a REST API that can be used to perform calculations of taxes as well as process validation/standardisation.

  You can also look at the liveAddress and the streets of smarty

  +++ Thank you Gareth

  Please indicate any update as "Good response" or "Useful answer" If this update help and answers your question, so that others can identify the correct/good update between the many updates.

• Formatting check box for the conditional statements in Adobe Acrobat format, form editor

  I'm looking for the format I should use boxes in Adobe Acrobat Pro XI, forms, Java Script Editor.  I am very familiar with this, as well as the use of the IF / AND statements.  I'm NOT using LiveCycle.

  Algorithm:

  -If either CB1 or CB2 are checked, then empty, equal

  -Si CB2 is checked then equal "N/a".

  D ' other...

  I don't know how I should be charged the formula.  I was also curious, I noticed in the properties of the box that the value of exports could be retained.  I've seen different variables, including here, Yes, 0, 1, True, etc.  Will there be an impact on the code?

  var v1 = + this.getField ("Check Box1") .value;
  var v2 = + this.getField ("Check Box2") .value;

  If ((v1 == "") & (v2 == "")) event.value = "";

  ElseIf (v2! == 'Off') event.value = "n/a";

  else event.value = ("... ») ;

  Any help is greatly appreciated.

  -Yes, of course. If you change the value of the export of the boxes - and then you have to adjust your code accordingly to take into account.

  -The value of a checkbox that is unchecked is always "Off".

  -When you add the symbol '+' before this.getField("XXX").value you want to convert it to a number. That doesn't look like a good idea in your case, then you should drop.

  -L' Boolean AND operator in JS is &, not &.

• Generate custom for the host storage reports

  Hello

  I have a use case where a I need to generate storage reports customized for i.e host host-> screen-> storage reports (reports on :) is an extension on reports taken hosts storage supported? I've seen examples of views views of performance or monitor. Please see the attachment for details

  If the case is taken over the extension on storage reports, we add another report for the reports on as an action?

  Thank you!

  Sorry, the points supported only buckets are those described in the SDK Programming Guide (and in document ExtensionPoints.html)

• Select the check box for the table of the ADF

  Hi all
  
  I want to add the check box in front of each line. The user will select the row by clicking the box and going to treatment by clicking on a button.
  
  I just almost all possible discussions on OTN.
  
  What I've done so now
  1] added a transitional Boolean attribute in my VO. added as a selectBooleanCheckbox in .jspx page.
  [2] a button with backing bean that will do the processing. [He will pick up the attributes of all ranks and be written in a file]
  [* 3] it works fine if I use the default option of line by Ctel selection + A, or by pressing Ctrl + click or SHIFT + arrow key. Backing bean is not the issue.*
  [4] try to intercept the TableSelection Listner also.
  
  It comes
  
  When I select the check box, only the last selected line is processed and not all lines. How to make the selectable online by clicking on the checkbox.
  
  I use JDeveloper 11.1.1.5
  
  Refered links
  http://www.gebs.ro/blog/Oracle/Oracle-ADF-row-selection-using-checkboxes/
  http://technology.AMIS.nl/2010/07/29/ADF-11g-select-all-rows-in-an-ADF-table/
  http://Sameh-Nassar.blogspot.nl/2009/12/use-checkbox-for-selecting-multiple.html
  http://www.Oracle.com/technetwork/developer-tools/ADF/learnmore/99-checkbox-for-delete-in-table-1539659.PDF
  
  Mukesh.

  https://www.dropbox.com/s/1gqsaobgyjycie6/AddDeleteEmployees.rar
  

• java.sql.SQLException: JDBC LLR, table check failed for the table ' WL_LLR_ADMI

  Hello
  
  I am trying to install OSB in a different domain. I already have a suite of soa running.
  
  This is the directory structure
  Middleware/user_projects/domains
  
  (a) soa_domain
  (b) osb_domain
  
  Who, from the administration server for the BSO, I get error below.
  
  
  Error: -.
  < server failed. Reason: Last forest resource [JTAExceptions:119002] failed during initialization. The server cannot start unless all configured logging last resource (LLRs) initialize. Fault reason:
  javax.transaction.SystemException: weblogic.transaction.loggingresource.LoggingResourceException: java.sql.SQLException: check table JDBC LLR, failed for the table "WL_LLR_ADMINSERVER", line ' JDBC LLR field / / server ' record had an unexpected value ' soa_domain / / AdminServer' expected ' osb_domain / / AdminServer'* ONLY the domain and the server that creates a table original LLR can access *.
  
  
  
  I see the solution in https://blogs.oracle.com/epc/entry/technical_table_verify_failed_for but I have no doubt here.
  
  When I run
  
  Select RECORDSTR in the WL_LLR_ADMINSERVER where
  XIDSTR = "field of LLR JDBC / / server ';"
  
  I get the result like-> soa_domain / / AdminServer
  
  
  If I change it to osb_domain / / this AdminServer, will affect my soa_domain server... ? Please advice
  
  Published by: user10720442 on December 11, 2012 11:54

  Hello

  There are two possible solutions to this problem:

  Solution 1:

  To solve this problem reconfigures the basic information database of Point differently for each domain, if you have more than one domain. That, to change the port of the database and the name below two files in the field

  In the setDomainEnv.cmd (or .sh) file inside directory change DOMAIN_HOME/bin Point base port number and the name of the comic.

  Set POINTBASE_PORT = 9094
  Set POINTBASE_DBNAME = weblogic_eval2

  JDBC:PointBase:server://localhost:9094 / weblogic_eval2

  In the file wlsbjmsrpDataSource - jdbc.xml inside change DOMAIN_HOME/config/jdbc directory under entries with port of pointbase database updated and the name (this will be in two places in the file).

  Solution 2:

  If the domain name has been changed and do not want to change the database properties, then an update to the WL_LLR_ADMINSERVER table is possible:

  that is to say:
  Update SCHEMA_SAMPLE. Set RECORDSTR = WL_LLR_ADMINSERVER ' base_domain / / AdminServer' where XIDSTR = "JDBC LLR field / / server ';"

  Kind regards
  Kal

• Set a custom for the first password rule

  Hi all friends of apex
  
  How to define custom rules for the first password resets.
  for ex
  Password length 6 min
  Must have 1 capital
  Must have 1 tiny
  Time-out in 20 minutes
  Must have a punctuation character
  At least 2 characters must change password next
  
  
  
  Thank you!

  Not all these features exist, but here's how to set password policies in the Apex:

  http://docs.Oracle.com/CD/E14373_01/admin.32/e13371/adm_wrkspc.htm#AEADM204