PREINST2. File management of stormwater is absent during the procedure of recovery on Satellite A300

Similar Questions

• How can satellite A135-S4656 - I burn PREINST2. File management of stormwater on the DVD?

  I just got the recovery DVD, the post and in the process "cannot read the source file or disk.
  Its new obtained by the post. Can someone send me a link so I can burn the file on the DVD

  PREINST2. FILE MANAGEMENT OF STORMWATER 628 MB 31/05/2007

  Please reply with the link, or file

  estefan2020 at hotmail dot com

  Thank you.

  PS. Optical disc is good, have obtained if part, he's stuck not being able to read this file.

  Thanks again!

  Hello

  Looks like your CD/DVD drive cannot read the disc properly.
  The drive is faulty or the STRANGE laser lens is dirty

  Try to clean the lens of the laser using a fluid tip and alcohol of wadding.
  Then test this new
  You can also try to copy these recovery discs using another computer and could finally try to boot from the recovery disc copied.

• During the installation of recovery that it off

  I recently baught a new laptop computer from a friend and I so wanted to restore factory settings. I inserted the disc and went through the adjustment, and he began to restore. At halfway through the process of close to 50% turns off/on overheating. It tells me to insert the disc starts, which I did not, and now I don't know what to do because it does not start without it.

  What can I do and where can Iget a new?

  Please answer ([email protected])

  Thank you!!

  Hello

  I think the solution to this problem is quite easy. If the computer turns off during the installation of recovery you need to do this installation once again, I think that because some files are missing, etc.

  Then boot from the recovery disc and try again.

  By the way: it would be interesting to know which laptop, you have exactly. If it overheat, try to clean it using the jet of compressed air. ;)

• Upgrades - during the procedure, my PC says it is install updates - but after doing what he wonyt restart and I need to go to restart from the last successful to get windows to restart - ideas?

  Upgrades - during the procedure, my PC says it is install updates - but after having done this, she does not restart and I need to go to restart from the last successful to get windows to restart - ideas?

  Windows Update Forum:

  It's updated operating system Vista, upgraded installation and activate Forum.

  You will get the best help for any problem of Update/Service Pack in the Windows Update Forum; the link below:

  http://social.answers.Microsoft.com/forums/en-us/vistawu/threads

  When you repost here, kindly include the Error Codes, and exactly what is happening when you try to update.

  In this way, you will receive the best help.

  See you soon.

  Mick Murphy - Microsoft partner

• Recently ordered (and order confirmed) "Plan of creative photography of Cloud (one year). I want to cancel it, but during the procedure, I do not even the option "Cancel". How should I proceed?

  Recently ordered (and order confirmed) "Plan of creative photography of Cloud (one year). I want to cancel it, but during the procedure, I do not even the option "Cancel". How should I proceed?

  In order to cancel the order, please contact customer service

  You can use: http://helpx.adobe.com/x-productkb/global/phone-support-orders.html

  For more information on cancellation: cancel your creative cloud membership

• Drive CD/DVD not visible in BIOS, Device Manager or Windows Explorer - only during the analysis of the system.

  Until a few days ago, this problem didn't exist - I know.  My CD/DVD drive is no longer recognized in Windows Explorer, BIOS or Device Manager.  It doesn't, however, appears briefly in Windows Explorer in the analysis of the security of the computer.  It allows to open/close, etc.  and when it is visible, I am able to open the drive and see the contents of the CD.  Then it disappears again.  The light flashes indicating that he works and I can hear it trying to read the CD.  I uninstalled iTunes because I read somewhere that this may have been the issue - but that didn't work.  I tried the system restore, registry cleaners, removal of upper/lower case filters from the registry, used the program Fixit found on the site Web of Microsofts etc and still no luck.  Any ideas?  The computer is a gateway SX2850 (?) with Windows 7 Home Premium installed.

  Hello

  Follow these steps to remove corruption and missing/damaged file system repair or replacement.

  Start - type in the search box - find command top - RIGHT CLICK – RUN AS ADMIN

  sfc/scannow

  How to fix the system files of Windows 7 with the System File Checker
  http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.html

  Then run checkdisk (chkdsk).

  How to run check disk in Windows 7
  http://www.SevenForums.com/tutorials/433-disk-check.html

  ==========================================================

  After the foregoing:

  References to Vista also apply to Windows 7.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The DVD player does not work after installing Windows 7
  http://support.Microsoft.com/kb/975270/

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during Windows Vista
  Setup after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and the
  correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry settings for your
  CD/DVD drive someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays
  all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

• Warning message to turn off "Are you sure that you want to copy this file/folder without its properties" message during the transfer of files and folders on network file servers? »

  Original title: Annoying message of loss of property

  Win7pro x 64 here.

  Is there a way to disable this annoying message "Are you sure you want to copy this file/folder without its properties" during the transfer of files and folders in all of network file servers?

  Pokermon salvation,

  It would be better if post you this question in the forum category below where this problem is related to Windows server 2003.

  Windows Server forums

  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

  If all goes well, they will be able to solve this problem.

  Kind regards

  Shinmila H - Microsoft Support

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Files Management tab does not appear in the import module. I think that I have configured some settings but am unable to change. I restored the factory default preferences, removed and reinstalled on Macbook, but they are always there for example allow du

  I am new to Lightroom and I followed a guide that allowed me to set import preferences. Now I want to change them, and although I see them in the import dialog box small I don't see a "File management" tab at any time. I have reset factory default in the preferences and removed and re-installed on my Macbook, but they are still there.

  Any advice would be much appreciated as I'm looking for guides and forums but did not find any specific help. Thank you.

  Click on apply when importing

  You see file handling

  If so just select

  

  Hope this helps

  Assani

• Satellite L355D-S7825 - hangs during the installation of recovery

  My laptop girls. She asked me to restore the computer to factory settings. It is running Vista Home Premium 32 bit. I tried the restore disks 4 times now to pretty much the same results. It will get all the way to the "application final Configuration where it installs the user manual and the office links and then it's there. After reading several posts here with the same problem, I decided to let it sit all night. This morning it had expired. I clicked on the button of the mouse to wake him up. It passes to the logon screen. It shows login Admin and says that the account has been locked, please contact your system administrator. How can this be? It won't let me! My only choice is to restart the system. After the reboot, it displays the screen of the AFC and reinstalls the two same files manual user and links and then it's there.

  I can minimize the screen of the AFC I did and then I changed the power settings to never expire. I have the WiFi off button as requested by AFC screen, as it will not be installed file links with WiFi turned on and the user manual. I don't know what else to do.

  Anyone has any ideas on this? What would you say if I was totally format the HD and then try to restore? Any help would be appreciated.

  Hi Poppi,

  What you mean with screen AFC?

  Well, if recovery installation doesn't work properly, it s hardware malfunction or the disk recovery...

  You can install Windows from a normal Microsoft drive correctly?

• HAVE LOTS OF PHOTOS ON THE LAPTOP... I WANT TO TRANSFER PHOTOS FROM MY P/C AND FILE HERE... WHAT IS THE PROCEDURE?

  I HAVE A LOT OF PHOTOS ON THE LAPTOP... I WANT TO TRANSFER PHOTOS FROM MY P/C... NEED HELP WITH THE PROCEDURE.

  There is certainly some options, you can take.  If the two computers are on the same network connection home, you could do it quite easily on the network.  Or the low-tech plugin is a USB flash drive, open the folder and drag image files, then take this drive on the new computer and plug it in and copy.  Last but not least, you can store your files on a synchronization as OneDrive or Google Drive service, and photos on a single computer would automatically transfer instantly to the other computer (which is also very handy as a backup).

• Manager insufficient message show up during the game.

  Have Windows XP. Downloaded eGames escape the Museum 2, and while the play one window shows 'Manager ran out of spikes' and I can't continue.  How can I fix it?

  Hi cowstart,

  Start your computer in a clean boot and check if that helps. Steps to perform the clean boot:

  i. click Start, click run, type msconfigand click OK.

  II. the System Configuration utility dialog box appears.

  III. in the System Configuration utility dialog box, click the general tab and then click Selective startup.

  IV. Click to uncheck the Process SYSTEM. INI file check.

  v. Click to uncheck the process to WIN. INI file check.

  VI. Click to clear the Load Startup items check box. Check The Load System Services and to use Original BOOT. INI are checked.

  VII. click on the Services tab.

  VIII. Click to select the hide all Microsoft Services check box.

  IX. click disable all, and then click OK.

  x when you are prompted, click restart to restart the computer.

  XI. try playing the game of tp.

  You can check the link below to check if all software or third-party program is causing the error. Here is the link for the same thing: http://support.microsoft.com/default.aspx/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  i. Click Start, type msconfig.exe in the start search box and press ENTER.

  II. If you are prompted for an administrator password or for confirmation, type your password, or click on continue.

  III. on the general tab, click the Normal startup option and then click OK.

  IV. When you are prompted to restart the computer, click on restart.

  Please return back with the results.

  You can even check from the Web site. Link to the same thing:
        http://www.eGames.com/support.php

  Thank you, and in what concerns:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• File system, verify or repair failed during the installation of Sierra

  I downloaded Sierra and when he tried to install I get an error "file system check or repair a failure", how can I resolve this problem and install Sierra?

  Start of recovery

  and open disk utility:

  -Look at the Smart function. If other verified tham means disc is a failure. The disk may be failing, even if the status is verified.

  -If she tells checked then repair/First Aid disk. If it can be repaired and then try reinstalling the Sierra.

  If it is repairable, replace the drive

• Realtek PCIe Gbe family controller findFile error absent during the installation of the driver

  Model: HP ENVY TouchSmart 15-j052nr

  Question: Has lowered Windows 8 for windows 7 and

  (1) question:

  everything works fine except no USB 3.0 ports are working. I see an unknown device and it is not able to find the driver.

  Unknown device: Details column has ID Hardword

  IUSB3\ROOT_HUB30 & VID_8086 & PID_8C31 & REV_0005 & SID_1962103C

  IUSB3\ROOT_HUB30 & VID_8086 & PID_8C31 & REV_0005

  IUSB3\ROOT_HUB30 & VID_8086 & PID_8C31

  I tried to install https://downloadcenter.intel.com/Detail_Desc.aspx?DwnldID=22824 but it did not help.

  (2) question

  Another question: the Ethernet controller is missing the driver and I get findfile failed when I try to install the driver

  Controller Realtek PCIe Gbe family

  Error: http://answers.microsoft.com/en-us/windows/forum/windows_7-hardware/findfile-failed-the-realtek-netw...

  I tried pluggin ethernet cable when installing the driver also but no result

  You are the very welcome.

  If you have not installed c of the first Intel chipset driver and restart.

  https://Downloadcenter.Intel.com/Detail_Desc.aspx?AGR=Y&ProdId=816&DwnldID=20775&keyword=chipset+installation+utility&lang=eng

  Then, I would try the driver directly from Realtek on the link below.

  You want to download and install the second driver file on the list.

  http://www.Realtek.com.tw/downloads/downloadsView.aspx?langid=1&PNid=13&pfid=5&level=5&Conn=4&DownTypeID=3&GETDOWN=false

• I am trying to create a PDF to a file, however, it only recongnizes 6 files on more than 50 years during the search "all formats supported.

  When I try to create a pdf file it will not recognize in "all formats supported" the .xls.  He has always done in the past, but I had to reload Adobe After my hard drive crashed and now it will not.  How to recognize the .xls

  The other Office formats are actually in the list of formats supported? If you installed Office after Acrobat, you might want to try doing a repair in Acrobat and if this does not work, uninstall and reinstall Acrobat.

• Qosimo G50 - 12G error occurs during the creation of recovery disks

  Nice day

  I have a Qosimo G50 - 12G and I tried several times to do disk recovery, but at some point
  the following error occurs:

  The following file cannot be read

  G:\08299Xsp4.SVM

  Error message: 020150-20-00000000

  Does anybode know what it means and how to fix this?

  Thamks

  Hello

  Have you changed something on your laptop? For example, the partitions of size or do you remove any content of the recovery of HARD drive partition?

  What is the G: drive in your case? Is it a partition or a CD/DVD player?

  I m not very well why this error pops up, but some users here in the forum reported about errors during recovery disc creation. In most cases the use of other and different DVD helped to address this problem.
  I m using the TDK DVD-R and I'm happy.